Page 1
for Advantix shower channel, for installation height of 95 mm
and up, reconstruction model can be cut to size subsequently
Model Year built:
4982.92 from 04/2016
en_INT
Advantix odour trap
Instructions for Use
Page 2
Advantix odour trap 2 from 16
Page 3
Table of contents
1 About these instructions for use 4
1.1
Target groups 4
1.2
Labelling of notes 4
1.3
About this translated version 5
2 Product information 6
2.1
Standards and regulations 6
2.2
Intended use 6
2.2.1
Areas of use 6
2.2.2
Media 6
2.2.3
Drainage capacity 7
2.3
Product description 7
2.3.1
Overview 7
2.3.2
Technical data 8
3 Handling 9
3.1
Assembly information 9
3.1.1
Important note 9
3.1.2
Installation dimensions 9
3.2
Assembly 10
3.2.1
Cutting the drain to size 10
3.2.2
Mounting the odour trap 11
3.3
Disposal 16
Table of contents
Advantix odour trap 3 from 16
Page 4
1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at
viega.com/legal
.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
n Heating and sanitary professionals and trained personnel
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Advantix odour trap 4 from 16
Page 5
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Advantix odour trap 5 from 16
Page 6
2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at
viega.com/standards
.
Regulations from section: Media
Scope / Notice Regulations applicable in Ger-
many
Typical domestic wastewater DIN 1986-3
2.2 Intended use
2.2.1 Areas of use
The Advantix odour trap is suitable for use in ViegaAdvantix shower
channels base unit model 4982.10 and model 4982.20.
The drain is designed for small to medium volumes of water, which
occur in e. g. residential building.
Technical information, see
Ä Chapter 2.3.2 „Technical data“ on page 8
.
The drain is suitable for horizontal connection to the drainpipe.
2.2.2 Media
The drain is intended for draining of household-type wastewater in constant operation, see
Ä „Regulations from section: Media“ on page 6
.
n
The short-term temperature of the wastewater may reach up to
95° C. The temperature must be considerably lower in constant
operation.
n The pH value must be higher than 4 but lower than 10.
It is not permitted to introduce wastewater which would damage the
product material.
Product information
Advantix odour trap 6 from 16
Page 7
2.2.3 Drainage capacity
The drainage capacity at an accumulation height of 10 mm above the
grate is 0.5 l/s
The drainage capacity at an accumulation height of 20 mm above the
grate is 0.55 l/s
2.3 Product description
2.3.1 Overview
1
2
3
4
5
1 - Odour trap immersion pipe
2 - Odour trap insert
3 - O-ring
4 - Casing
5 - Adapter DN50
10
20
Product information
Advantix odour trap 7 from 16
Page 8
2.3.2 Technical data
Nominal width [DN] (drain
socket)
DN40 / DN50
Drainage capacity
Ä Chapter 2.2.3 „Drainage capacity“
on page 7
Dimensions and installation height
Ä Chapter 3.1.2 „Installation dimensions“ on page 9
Water seal level 50 mm
Load class K = 300 kg
Product information
Advantix odour trap 8 from 16
Page 9
3 Handling
3.1 Assembly information
3.1.1 Important note
Observe the instructions for use of the base unit when
mounting.
Before assembly:
n Check if the drainage capacity of the drain is sufficient for the arising
water volume
Ä Chapter 2.2.3 „Drainage capacity“ on page 7
.
n Check if the installation height of the drain corresponds with the
planned floor construction.
n Ensure that the required connection line is installed with the neces-
sary incline to the planned installation location.
During assembly:
n Observe installation dimensions.
3.1.2 Installation dimensions
Fig. 1: Dimensional drawing for model 4982.92
Dimensional drawing
Handling
Advantix odour trap 9 from 16
Page 10
95-155
95
Fig. 2: Installation height for model 4982.92
3.2 Assembly
3.2.1 Cutting the drain to size
Requirements:
n You want to cut the odour trap to the size of the reconstruction
model.
Cut the casing at the sawing groove provided for this purpose.
Cut the odour trap insert at the sawing groove provided for this purpose.
Installation height
Handling
Advantix odour trap 10 from 16
Page 11
Cut the odour trap immersion pipe at the sawing groove provided
for this purpose.
ð
You have cut the odour trap to the size of the reconstruction
model.
3.2.2 Mounting the odour trap
Check the connection element for soiling, clean if necessary.
Determine the screed height.
H
Handling
Advantix odour trap 11 from 16
Page 12
Mount the sealing element.
Check the sealing element for firm seat.
Press the drain into the connection element until it snaps home.
With mounting heights of max. 70 mm, align the base unit in the
mortar bed.
Provide mortar bedding to secure the drain against slipping.
Handling
Advantix odour trap 12 from 16
Page 13
Check whether grounding is required.
Set the base unit to the upper edge of the screed.
Align it horizontally in all directions.
INFO! The drain is 180° rotatable.
Connect the drain DN40 or the adapter element DN50 to the
drainage system.
The wastewater pipe can also be laid under the shower channel
base unit.
Put in the odour trap insert.
Handling
Advantix odour trap 13 from 16
Page 14
The odour trap in installed condition.
Turn the odour trap 90° to the right.
Mount and grease the sealing element.
Insert the odour trap immersion pipe.
ð
The odour trap insert has been fastened.
Check the base unit including the drain and the connection line for
leak tightness.
Handling
Advantix odour trap 14 from 16
Page 15
Insert the hard foam block.
Mount the first part of the site protection.
Remove the lower protective foil and stick the adhesive points on.
Shorten the second part of the site protection if applicable, and
mount it.
Remove the top protective foil of the adhesive point.
Handling
Advantix odour trap 15 from 16
Page 16
Line the shower channel incl. the drain up to the upper edge of the
flange with screed.
3.3 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Advantix odour trap 16 from 16
Loading...