Page 1
Kellermeister cellar drain
Instructions for Use
Model Year built:
4956.4 from 01/1998
en_INT
Page 2
Kellermeister cellar drain 2 from 12
Page 3
Table of contents
1 About these instructions for use 4
Table of contents
1.1
1.2
1.3
Target groups 4
Labelling of notes 4
About this translated version 5
2 Product information 6
2.1
2.2
2.2.1
2.2.2
2.2.3
2.3
2.3.1
2.3.2
2.4
2.4.1
2.5
Standards and regulations 6
Intended use 6
Areas of use 6
Media 6
Drainage capacity 7
Product description 7
Overview 7
Technical data 8
Information for use 8
Installation variations 8
Accessories 8
3 Handling 9
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.1
3.3
3.3.1
3.3.2
3.4
Assembly information 9
Important note 9
Installation dimensions 9
Tools and materials 10
Assembly 10
Connecting the drain 10
Care 11
Care tips 11
Cleaning the drain 11
Disposal 12
Kellermeister cellar drain 3 from 12
Page 4
About these instructions for use
1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
n Heating and sanitary professionals and trained personnel
n Tilers
n Consumers
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
viega.com/legal
.
1.2 Labelling of notes
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
Kellermeister cellar drain 4 from 12
Page 5
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Kellermeister cellar drain 5 from 12
Page 6
2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at
Regulations from section: Media
Scope / Notice Regulations applicable in Ger-
Typical domestic wastewater DIN 1986-3
viega.com/standards
Product information
.
many
2.2 Intended use
2.2.1 Areas of use
2.2.2 Media
The drain is intended for use in floor constructions without sealing –
e. g. cellars where wastewater occurs in small quantities at irregular
intervals.
Technical information, see
The drain is intended for draining of household-type wastewater in constant operation, see
n
The short-term temperature of the wastewater may reach up to
95° C. The temperature must be considerably lower in constant
operation.
n The pH value must be higher than 4 but lower than 10.
It is not permitted to introduce wastewater which would damage the
product material.
Ä Chapter 2.3.2 „Technical data“ on page 8
Ä „Regulations from section: Media“ on page 6
.
.
Kellermeister cellar drain 6 from 12
Page 7
2.2.3 Drainage capacity
1
2
10
20
Product information
2.3 Product description
2.3.1 Overview
Nominal width [DN] (drain
100
socket)
Drainage capacity at an accumu-
1.6 l/s
lation height of 20 mm above the
grate
The values are dependent on the total height of the drain unit.
Fig. 1: Components
1 - grate, model 4956-551
2 - base unit
Kellermeister cellar drain 7 from 12
Page 8
2.3.2 Technical data
Product information
2.4 Information for use
2.4.1 Installation variations
Nominal width [DN]
(drain socket)
Nominal width [DN]
(inlet)
Drainage capacity
100
50 or 70 (only in connection with connecting
piece model 4997)
Ä Chapter 2.2.3 „Drainage capacity“
on page 7
Water head seal 50 mm
Dimensions and
installation height
Load class K = 300 kg
The drain can be mounted in the following way:
n in a drill hole
n in a floor recess
Ä Chapter 3.1.2 „Installation dimensions“
on page 9
2.5 Accessories
Optional accessories
Optionally, a connecting piece can be fitted. The connecting piece
serves as a possible additional inlet (DN 50 or DN70).
Kellermeister cellar drain 8 from 12
Page 9
3 Handling
3.1 Assembly information
3.1.1 Important note
Before assembly:
n Check if the drainage capacity of the drain is sufficient for the arising
n Check if the installation height of the drain corresponds with the
n Ensure that the required connection line is installed with the neces-
During assembly:
n Observe installation dimensions.
water volume
planned floor construction.
sary incline to the planned installation location.
Ä Chapter 2.2.3 „Drainage capacity“ on page 7
Handling
.
3.1.2 Installation dimensions
Fig. 2: Dimensional drawing
Kellermeister cellar drain 9 from 12
Page 10
3.1.3 Tools and materials
Required material
n Material for securing the drain
n For the mounting of the connecting piece (optional):
3.2 Assembly
3.2.1 Connecting the drain
Connecting to the wastewater system
The connection to the wastewater system must be completed before
the drain can be installed in the floor construction. Proceed as follows:
Requirements:
Handling
compass saw
Mounting the drain
n A pipe to the planned drainage position is already in place for the
connection to the wastewater system.
n The drainpipe has an internal sealing lip.
Push the drain socket into the drainpipe completely.
Position the drain at the desired height at the place of use. If necessary, raise or lower in the existing floor using suitable material.
Align drain horizontally using a spirit level.
Kellermeister cellar drain 10 from 12
Page 11
Handling
Secure the drain in such a way that it cannot shift when the subsequent works are applied.
Most importantly, it must be ensured that the drain does not float
when the concrete or screed is poured in.
Work the drain into the screed or floor covering.
NOTICE!
Product damage due to improper installation
If hollow spaces occur during the lining of the drain, leaks
may occur when pressure is applied.
Inform the subsequent workers that the drain must be fully
lined and that there must be no hollow spaces.
3.3 Care
3.3.1 Care tips
3.3.2 Cleaning the drain
Normal soap or a mild cleaning agent can be used for regular care and
prevention of lime scale on the grate and frame. Under no circumstances should scouring agent or scratching objects be used.
Strong stains, even around the drain unit and the siphon, can be
removed using typical household cleaner. It should be noted that the
cleaning agent should be rinsed off after the prescribed soaking time.
There should be no residue on the components.
We recommend using a mild cleaning agent and a washing-up brush for
cleaning.
Remove and clean grate.
Kellermeister cellar drain 11 from 12
Page 12
Clean drain.
Re-insert grate.
Handling
3.4 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Kellermeister cellar drain 12 from 12
Loading...