Vidikron VP-5000 User Manual

OWNER’S OPERATING MANUAL

HIGH DEFINITION PLASMA DISPLAYS

Models VP-5000 and VP-5000a

THREE YEAR LIMITED WARRANTY

For Plasma Displays

Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup
and care, you should enjoy many years of unparalleled video performance.

This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other
important documents.

WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

SERVICE LABOR: Vidikron will pay for service labor by a Vidikron Authorized Service Center when needed as a result of a
manufacturing defect for a period of three (3) years from the effective date of delivery to the end user (excluding the plasma glass
panel).

PARTS (not including plasma glass panel): Vidikron will provide new or rebuilt replacement parts for the parts that fail due to
defects in materials or workmanship for a period of three (3) years from the effective date of delivery to the end user. Such
replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.

PLASMA GLASS PANEL: Vidikron will pay for service labor by a Vidikron Authorized Service Center when needed as a result of a
manufacturing defect for a period of one (1) year from the effective date of delivery to the end user. In addition, Vidikron will
provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of one (1)
year from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the remaining
portion (if any) of the original warranty period.

Y

WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

Image burn-in on plasma display panels is specifically excluded from coverage under this Limited Warranty. Image burn-in is the
result of misuse of the product and therefore cannot be repaired under the terms of this Limited Warranty.

Normal viewing material such as television/satellite broadcasts, videotape or DVDs (not put into pause for extended periods of
time) will not cause damage to your display under normal conditions. Many DVD players are also equipped with screen savers for
this reason.

TO AVOID IMAGE RETENTION (Burn-in): Please ensure that still images are left on your plasma display panel for no more than a
few minutes. Also ensure that images displayed in the 4:3 aspect ratio mode (black or gray stripes, but no picture information is
present on the left and right edges of the screen) are used as infrequently as possible. This will prevent permanent image burns on
your plasma display panel, which can be seen permanently under certain conditions once burn-in has occurred.

The types of images to avoid include video games, still images and computer screens with stationary tool bars and icons. (This is
why computers are equipped with screen savers – to prevent still images from burning into the monitor’s phosphors after being
displayed continuously for an extended period of time).

This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not
cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from
accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper
maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and brownouts;
damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote control units,
damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this Limited Warranty.

PRE

IMINAR

L

Vidikron PlasmaView Owner’s Operating Manual iii

CAUTION: THIS LIMITED WARRANTY ONLY COVERS VIDIKRON PRODUCTS PURCHASED FROM VIDIKRON AUTHORIZED DEALERS.
ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. MOREOVER, DAMAGE
RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE
UNDER THIS LIMITED WARRANTY. IT IS IMPERATIVE THAT INSTALLATION AND SETUP WORK BE PERFORMED ONLY BY AN
AUTHORIZED VIDIKRON DEALER TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY. THIS WILL ALSO ENSURE THAT YOU ENJOY
THE FINE PERFORMANCE OF WHICH YOUR VIDIKRON PRODUCT IS CAPABLE WHEN INSTALLED AND CALIBRATED BY VIDIKRON
AUTHORIZED PERSONNEL.

RIGHTS, LIMITS AND EXCLUSIONS:

Vidikron limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There
are no express warranties. Vidikron also excludes any obligation on its part for incidental or consequential damages related to the
failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some
states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

EFFECTIVE WARRANTY DATE:

This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as
evidence of the purchase date.

IMPORTANT – WARRANTY REGISTRATION:

Y

Please fill out and mail your warranty registration card. It is imperative that Vidikron knows how to reach you promptly if we should
discover a safety problem or product update for which you must be notified.

IMINAR

L

CONTACT A VIDIKRON AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:

Repairs made under the terms of this Limited Warranty covering your Vidikron video product will be performed at the location of
the product, during usual working hours, providing location of product is within normal operating distance from a Vidikron
Authorized Service Center. In some instances it may be necessary for the product to be returned to the Vidikron factory for repairs.
If, solely in Vidikron’s judgment, location of product to be repaired is beyond normal operating distance of the closest Vidikron
Authorized Service Center, or the repair requires the unit be returned to the Vidikron factory, it is the owner’s responsibility to
arrange for shipment of the product for repair. These arrangements must be made through the selling Vidikron Dealer. If this is not
possible, contact Vidikron directly for a Return Authorization number and shipping instructions. Vidikron will return product
transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be the
responsibility of the owner.

COPYRIGHT AND TRADEMARKS:

© Copyright 2007 Vidikron, a Runco International Company. This document contains proprietary information protected by
copyright, trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic or other means, in any form, without prior written permission of the manufacturer.

Vidikron, Vision, DVSI, Imagix, CineWide, AutoScope, V2 Aperture Control, CSMS and IntelliWide are trademarks of Runco, LLC. All
other trademarks and registered trademarks used in this document are the property of their respective owners.

PRE

Vidikron products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents Pending.

iv Vidikron PlasmaView Owner’s Operating Manual

ADDITIONAL INFORMATION:

To locate the name and address of the nearest Vidikron Authorized Service Center, or for additional information about this Limited
Warranty, please call or write:

VIDIKRON

Attn: Customer Service Department

2900 Faber Street

Union City, CA 94587

Ph: [phone]

Fax: [phone]

Toll Free: (888) 4VIDIKRON

VIDIKRON PRODUCT INFORMATION

RETAIN THIS INFORMATION FOR YOUR RECORDS

Y

IMINAR

_________________________________________________________ ________________________________________

L

Model Purchased Date

____________________________________________________________________________________________________________

Serial Number

____________________________________________________________________________________________________________

Vidikron Authorized Dealer Name

____________________________________________________________________________________________________________

PRE

Address

____________________________________________ __________________ ________________________

City State/Province Postal Code

____________________________________________ _______________________________________________________

Phone Fax

Vidikron PlasmaView Owner’s Operating Manual v

Safety Precautions

Thank you for your purchase of this quality Vidikron video product! It has been designed to provide you with the quality of video
that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the
menus and operation.

WAR NING

CAUTION

RISK OFELECTRIC SHOCK

DO NOTOPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

CAUTION

To turn off main power, be sure to remove the plugs from power outlets. The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.

WAR NIN G

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S
POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

WAR NIN G

CAUTION:

SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.

Y

IMINAR

L

This equipment has been tested and found to comply with the limits for a Class ‘B’ digital device, pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the Installation Manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area may cause harmful interference, in which case the user will be required to correct the interference at his own
expense.

DOC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Please read and follow the safety precautions listed below to ensure the equipment is free from damage, and to ensure that no
injury will occur as a result of improper use.

• Do not insert any object, especially metal or liquids, into the plasma display.

• Do not place any objects containing water or any other liquid on top of the plasma display.

• Do not place the units in direct sunlight, near heaters or in extremely dusty or humid locations.

• Do not install this system outdoors or otherwise exposed to the elements.

• Do not place heavy objects on top of the plasma display.

• If the power cord is damaged or frayed in any way, electrical shock and/or fire may result. Do not place objects on the power
cord, and keep the cord away from heat-emitting devices. Should the power cord become damaged in any way, please contact
your Vidikron Dealer for a replacement cord.

• Do not remove the cover of the plasma display for any reason. If any problems arise with the unit, please contact a Vidikron
Dealer or Vidikron for service. Removing the covers will void the warranty.

PRE

vi Vidikron PlasmaView Owner’s Operating Manual

1Table of Contents

THREE YEAR LIMITED WARRANTY .......................................................................................... iii

Safety Precautions ................................................................................................................... vi

1. Introduction ........................................................................................................................ 1

About This Manual ............................................................................................................................................ 1

Target Audience......................................................................................................................................... 1

If You Have Comments About This Manual... .................................................................................. 1

Textual and Graphic Conventions ....................................................................................................... 1

Using This Manual ............................................................................................................................................. 2

Description, Features and Benefits ............................................................................................................. 3

Key Features and Benefits....................................................................................................................... 3

Parts List ....................................................................................................................................................... 4

2. Controls and Functions ...................................................................................................... 5

PlasmaView at a Glance .................................................................................................................................. 5

Controls and Indicators ........................................................................................................................... 5

Connectors .................................................................................................................................................. 6

IMINAR

Y

PlasmaView Remote Control ......................................................................................................................... 8

3. Installation ........................................................................................................................ 11

Remote Control ................................................................................................................................................ 11

PRE

Quick Setup ....................................................................................................................................................... 13

Installation Considerations ..........................................................................................................................14

Connections to the PlasmaView ................................................................................................................17

L

Notes on Batteries ................................................................................................................................... 11

Notes on Remote Control Operation................................................................................................ 11

High-Altitude Operation .......................................................................................................................14

Mounting the PlasmaView on a Wall or Table Stand.................................................................. 14

Ambient Light ........................................................................................................................................... 15

Ventilation .................................................................................................................................................. 15

Other Considerations ............................................................................................................................. 16

Connecting the PlasmaView to Source Components ................................................................ 17

Audio Connections..................................................................................................................................18

RS-232 Controller Connection ............................................................................................................ 19

Cable Management.................................................................................................................................20

Vidikron PlasmaView Owner’s Operating Manual vii

Table of Contents

4. Operation .......................................................................................................................... 21

Turning on the Power ....................................................................................................................................21

Setting the PC Display Properties ..............................................................................................................22

Using the On-Screen Menus ........................................................................................................................23

Main Menu ................................................................................................................................................25

Picture Adjust ............................................................................................................................................25

Audio Setup ...............................................................................................................................................32

Image Options .......................................................................................................................................... 32

Install ............................................................................................................................................................ 35

Function ...................................................................................................................................................... 37

Signal Info ..................................................................................................................................................41

5. Maintenance and Troubleshooting ................................................................................ 43

Troubleshooting Tips .....................................................................................................................................43

6. Serial Communications ....................................................................................................45

Y

RS-232 Connection and Port Configuration ..........................................................................................45

Serial Command/Response Messages .....................................................................................................45

Example....................................................................................................................................................... 45

Command List...........................................................................................................................................46

7. Specifications .................................................................................................................... 55

PlasmaView Specifications ........................................................................................................................... 55

PlasmaView Dimensions ............................................................................................................................... 56

Computer/Video Signal Compatibility ....................................................................................................57

IMINAR

L

PRE

viii Vidikron PlasmaView Owner’s Operating Manual

1List of Figures

2-1. PlasmaView Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2-2. PlasmaView Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2-3. PlasmaView Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3-1. Available Range of the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3-2. Ventilation Requirements for Enclosure Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3-3. PlasmaView Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3-4. RS-232 Control System Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3-5. Installing the Cable Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4-1. Attaching the Ferrite Cores to the Power Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4-2. PlasmaView OSD Menu Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4-3. Typical PLUGE Pattern for Adjusting Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4-4. Typical Gray Bar Pattern for Adjusting Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4-5. Typical Color Bar Pattern for Adjusting Color Saturation and Tint . . . . . . . . . . . . . . . . . . . . . . . . 27

4-6. Typical Test Pattern for Adjusting Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4-7. Zoom Navigation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4-8. Image Freeze Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

7-1. PlasmaView Model VP-5000/VP-5000a Dimensions (with Table Stand) . . . . . . . . . . . . . . . . . . . 56

IMINAR

L

Y

PRE

Vidikron PlasmaView Owner’s Operating Manual ix

List of Figures

Notes:

Y

IMINAR

L

PRE

x Vidikron PlasmaView Owner’s Operating Manual

1Introduction

This Owner’s Manual describes how to install, set up and operate the Vidikron PlasmaView
High-Definition Plasma Display (Model VP-5000 or VP-5000a). Throughout this manual, the
Vidikron PlasmaView High-Definition Plasma Display is referred to simply as the
“PlasmaView.” Except where noted, the information in this manual applies to both
PlasmaView models.

most out of the PlasmaView.

Vidikron has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
may require updating from time to time. You can always find the latest version of this and
other Vidikron product manuals on-line, at www.Vidikron.com.

Vidikron welcomes your comments about this manual. Send them to [e-mail].

Text Conventions: The following conventions are used in this manual, in order to clarify the
information and instructions provided:

• Remote control button identifiers are set in upper-case bold type; for example, “Press EXIT
to return to the previous menu.”

• Computer input (commands you type) and output (responses that appear on-screen) is
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to 16:9,
send the command DF 80 60 51 01 05 16.”

• All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <Spacebar>, <Control>,
<Esc> and <Tab>.

• <Enter> indicates that you may press either the RETURN or ENTER key on your keyboard
if it has both keys.

PRE

IMINAR

L

Y

1.1 About This Manual

Target AudienceVidikron has prepared this manual to help home theater installers and end users get the

If You Have Comments About This Manual...

Textual and Graphic Conventions

In addition to these conventions, underlining, boldface and/or italics are occasionally used to
highlight important information, as in this example:

WARNING

Vidikron PlasmaView Owner’s Operating Manual 1

To prevent image retention (burn-in) on your display, ALWAYS use a
screen saver and set it to the shortest possible time.

Introduction

Graphic Conventions: These symbols appear in numerous places throughout the manual,
to emphasize points that you must keep in mind to avoid problems with your equipment or
injury:

1.2

Using This Manual

Tip

Note

Caution

TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.

NOTES emphasize text with unusual importance or special significance.
They also provide supplemental information.

CAUTIONS alert users that a given action or omitted action can degrade
performance or cause a malfunction.

Y

WARNING

DANGER!

Use the following table to locate the specific information you need in this manual.

WARNINGS appear when a given action or omitted action can result in
damage to the equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or death.

IMINAR

If you need... ... Turn to page:

Information about obtaining service iv

L

General information about the PlasmaView
High-Definition Plasma Display

Installation instructions 11

First-time configuration instructions 23

PRE

Advanced configuration instructions 35

Troubleshooting tips 43

Specifications for the PlasmaView High-Definition
Plasma Display

3

55

2 Vidikron PlasmaView Owner’s Operating Manual

Introduction

Vidikron’s PlasmaView High-Definition Plasma Display is perfect for high-definition viewing.
Advanced engineering and design features and state-of-the-art performance make the
PlasmaView the ideal choice for those wanting true high definition capability with a
resolution of up to 1365 x 768.

The PlasmaView handles all HDTV signals with ease, in addition to standard television. A 16:9
native resolution display panel with advanced engineering innovations gives you the
brightest, clearest images possible. Vidikron’s superior video processing with 3:2 film
detection circuitry is built into the monitor and provides exceptional detail and artifact-free
video enhancement, elevating even standard NTSC material to near-HD quality.

Multiple aspect ratio control includes Vidikron’s IntelliWide™ mode, offering the ability to
view standard video formats in widescreen without loss of image quality. IR and discrete
RS-232 controls facilitate glitch-free custom installation, while Dynamic Pixel Protection™
helps to protect the plasma panel from stationary image burn.

A generous number of inputs and the sleekest styling around make this flat-panel display
monitor a great value and the ideal choice for discerning viewers.

For high-altitude installations, Vidikron also offers the VP-5000a with industry-leading
high-altitude compliance to over 9000 feet (2,740 meters) mean sea level (MSL). The
VP-5000a shares all other features and specifications with the VP-5000.

• 16:9 Native Resolution: 1365 x 768

• Screen Size (diagonal): 50 inches

• Multiple Aspect Ratios with IntelliWide™ Mode

• Less than 5 inches deep

• Dual HDMI Inputs with High-bandwidth Digital Content Protection (HDCP)

•HDTV Compatible

• Exceptional detail and artifact-free video enhancement

• Superior video processing with 3:2 film detection circuitry

IMINAR

L

Y

PRE

1.3 Description, Features and Benefits

Key Features and BenefitsThe PlasmaView offers these key features and benefits:

Vidikron PlasmaView Owner’s Operating Manual 3

Introduction

Parts List Your PlasmaView is shipped with the following items. If any items are missing or damaged,

➤

please contact your Vidikron dealer or Vidikron Customer Service at (888) 4VIDIKRON.

• PlasmaView High-Definition Plasma Display

• AC Power Cord

• Remote Control Unit and two (2), AAA-size batteries

• Warranty information and registration card

• Vidikron PlasmaView Owner’s Operating Manual (this document)

•Ferrite cores (2)

• Cable Clamps

• Wall Mount Kit (part number VIHK-000200)

or

Table Stand (part number VIHK-000250)

• Safety metal fittings

• Screws for safety metal fittings

Note

Use the safety fittings to fasten the PlasmaView to a wall when using the
optional tablestand. This prevents tipping due to external shock. Use the
supplied screws to fasten the safety fittings to the holes in the back of the
plasma.

Y

IMINAR

L

PRE

4 Vidikron PlasmaView Owner’s Operating Manual

2Controls and Functions

Figure 2-1 and Figure 2-2 show the locations of the PlasmaView controls, indicators and
connectors.

IMINAR

2.1 PlasmaView at a Glance

Controls and Indicators

Y

L

MENU / ENTER

Located on bottom
of Plasma

VOLUME

DOWN UP LEFT/- RIGHT/+ /EXIT

INPUT SELECT

Located on bottom
of Plasma

PRE

7

Figure 2-1. PlasmaView Controls and Indicators

1. POWER BUTTON

Turns the monitor’s power on and off.

2. REMOTE CONTROL SENSOR

Receives the signals from the remote control.

3. POWER/STANDBY INDICATOR

- Lights red to indicate that the PlasmaView is in standby mode;

- Lights green to indicate normal operation;

- Flashes red to indicate that the internal temperature is too high.

4. INPUT SELECT/EXIT

Press this button to switch inputs, or exit the current menu if an On-Screen Display (OSD)
menu is visible.

6

5

4

1

2

3

Vidikron PlasmaView Owner’s Operating Manual 5

Controls and Functions

5. LEFT/– and RIGHT/+
These enlarge or reduce the image and function as CURSOR ( / ) buttons in OSD
mode.

6. VOLUME DOWN and UP
These adjust the volume and function as CURSOR ( / ) buttons in OSD mode.

7. MENU/ENTER
Press this button to access the On-Screen Display (OSD) controls. Press this button
during the display of the main menu to go to a submenu. Also used to select a
highlighted menu item or confirm a changed setting.

The Power on/off switch does not disconnect the plasma display

WARNING

completely from the supply mains.

Y

Connectors

PRE

➤

VIDEO AUDIO

1

2

L

RIGHT

LEFT

+ -

- +

2

4

1

DVD/HD

R

L

(

)

MONO

IMINAR

DVD/HD3DVD/HD

4

AUDIO

3

R

HDMI HDMI

L

(

)

MONO

AUDIO

R

L

EXTERNAL CONTROL

DVD/HD3DVD/HD

3

(

)

MONO

REMOTE

D-SUB

IN OUT

HDMI HDMI

4

1

Y Cb/Pb Cr/Pr

AUDIO

R

L

(
MONO

VIDEO AUDIO

1

R

1

L

(

)

2

MONO

2

)

AUDIO

2

DVD/HD

1

R

Y Cb/Pb Cr/Pr

L

(

)

MONO

DVD/HD

2

YCb/PbCr/Pr

DVD/HD

YCb/Pb

PC/RGB

2

D-SUB

Cr/Pr

PC/RGB

D-SUB

EXTERNAL CONTROL

D-SUB

AC IN

1

10

REMOTE

IN OUT

3

5678

Figure 2-2. PlasmaView Connector Panel

6 Vidikron PlasmaView Owner’s Operating Manual

9

1. POWER INPUT (100 to 240 VAC)
Connect the PlasmaView to power here, using the included power cord.

2. EXTERNAL SPEAKER OUTPUTS
Connect optional, external speakers here. Maintain the correct polarity. Connect the
(positive) and (negative) speaker wires to the EXT SPEAKER terminals on both the
LEFT and RIGHT channels. Please refer to the owner’s manual for your speakers.

3. VIDEO1, 2 (RCA, S-Video)
Standard, Composite video and S-Video inputs for connecting a DVD player, satellite
receiver, camcorder, laser disc player or Super VHS (S-VHS) VCR.

4. AUDIO1, AUDIO2, AUDIO3
Stereo, RCA-type audio inputs. You can associate each audio input with any video input

-- that is, specify which audio input becomes active when a given video source is
selected. For more information, refer to

5. DVD/HD1

DVD/HD2

Standard-definition (480i/576i) or high-definition (720p/1080i), YPrPb component
inputs for connecting a DVD player or high-definition TV source.

Audio Setup on page 32.

Controls and Functions

Y

Tip

6. PC/RGB (15-pin D-Sub)
Connect an analog RGB signal from a computer or DTV decoder here.

7. DVD/HD3, DVD/HD4 (HDMI)
HDCP-compliant digital video input for connecting a DVD player, personal computer or
HD tuner with a DVI or HDMI output.

8. EXTERNAL CONTROL (9-pin, male D-Sub)
A male, 9-pin D-sub connector for interfacing with a PC or home theater
automation/control system.

9. REMOTE IN (3.5-mm mini phone jack, tip/ring/sleeve)
Wired input from an external remote control or infrared (IR) receiver.

10. REMOTE OUT (3.5-mm mini phone jack, tip/ring/sleeve)
Wired output to the REMOTE IN jack of another device; allows you to control both the
PlasmaView and the other device using the same wired remote control.

For best results, do not run your DVD player in progressive mode.

IMINAR

L

PRE

Vidikron PlasmaView Owner’s Operating Manual 7

Controls and Functions

2.2

PlasmaView Remote Control

Figure 2-3 shows the PlasmaView remote control, and the paragraphs that follow describe its
functionality.

2

1

Y

3

4

6

IMINAR

5

7

8

9

L

12

13

PRE

Figure 2-3. PlasmaView Remote Control

10

11

14

8 Vidikron PlasmaView Owner’s Operating Manual

1. IR OUTPUT INDICATOR
Lights when a button is pressed to indicate that an IR signal is being transmitted.

2. POWER ON/OFF
Use these buttons to turn the PlasmaView on or off. (This does not operate when the
POWER/STANDBY indicator of the main unit is off.)

3. CURSOR ( , , , )
Use these buttons to select items or settings, adjust settings or switch display patterns.

4. EXIT
Press this button to exit the OSD controls in the main menu. Press this button during the
display of a submenu to return to the previous menu.

5. MENU
Press this button to access the On-Screen Display (OSD) controls. Press this button
during the display of the main menu to go to a submenu. Also used to select a
highlighted menu item or confirm a changed setting.

6. VID 1-2
Press this button to select VIDEO 1 as the source. Press it again to select VIDEO 2.

7. DVD-HD 1-4
Press this button repeatedly to select a DVD/HD source.

8. RGB
Press this button to select the PC/RGB input as the source.

Controls and Functions

Y

9. ASPECT
Press this button to select an aspect ratio. (Not active for all signals.)

10. MUTE
Press to mute the audio output. Press it again to restore the sound.

11. VOLUME (+/–)
Use these buttons to adjust the audio volume.

12. AUTO OFF
Press this button to set the sleep timer. Press it repeatedly to scroll through the available
options (30, 60, 90 or 120 minutes; or, select 0 to turn the timer off).

13. DISPLAY
Displays the currently-selected aspect ratio and input on the screen.

14. LIGHT
Press to illuminate the buttons.

PRE

IMINAR

L

Vidikron PlasmaView Owner’s Operating Manual 9

Controls and Functions

Notes:

Y

IMINAR

L

PRE

10 Vidikron PlasmaView Owner’s Operating Manual

3Installation

To install batteries in the remote control:

1. Remove the battery cover from the remote control.

2. Insert the two (2), AAA-size batteries included with the remote
control. Ensure that the polarities correctly match the
markings inside the battery compartment.

3. Replace the battery cover.

and

IMINAR

• Do not mix an old battery with a new one or different types of batteries.

• If you will not use the remote control for a long time, remove the batteries to avoid

damage from battery leakage.

L

3.1 Remote Control

Y

Notes on Batteries• When installing batteries, make sure that the battery polarities are correct.

The remote control can be used to control the PlasmaView within the ranges shown in Figure
3-1.

PRE

Approx.

23 ft (7m)

Figure 3-1. Available Range of the Remote Control

Vidikron PlasmaView Owner’s Operating Manual 11

Notes on Remote Control Operation