Vidikron Vision 12, Vision 10 User Manual

Download

Page 1

OWNER’S OPERATING MANUAL

10/12

DLP™ PROJECTORS

VERSION 2.0

Page 2

Page 3

TWO YEAR LIMITED WARRANTY

For Projectors, Video Processors and Controllers

Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup and care, you should enjoy many years of unparalleled video performance.

This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents.

WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

SERVICE LABOR: Vidikron will pay for service labor by Vidikron Authorized Service Center when needed as a result of manufacturing defect for a period of two (2) years from the effective date of delivery to the end user (excluding the lamp).

PARTS (not including the lamp): Vidikron will provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of two (2) years from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.

PROJECTOR LAMP: Vidikron will pay for service labor by a Vidikron Authorized Service Center when needed as a result of a manufacturing defect for a period of six (6) months or 1000 hours, whichever comes first, from the effective date of delivery to the end user. In addition, Vidikron will provide a new or rebuilt replacement lamp for the lamp that fails due to defects in materials or workmanship for a period of six (6) months or 1000 hours, whichever comes first, from the effective date of delivery to the end user. Such replacement lamps are then subsequently warranted for the remaining portion (if any) of the original warranty period.

WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

IMINAR

This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this Limited Warranty.

CAUTION: THIS LIMITED WARRANTY ONLY COVERS VIDIKRON PRODUCTS PURCHASED FROM VIDIKRON AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. IT IS IMPERATIVE THAT INSTALLATION AND SETUP WORK BE PERFORMED ONLY BY AN AUTHORIZED VIDIKRON DEALER TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY. THIS WILL ALSO ENSURE THAT YOU ENJOY THE FINE PERFORMANCE OF WHICH YOUR VIDIKRON PRODUCT IS CAPABLE WHEN INSTALLED AND CALIBRATED BY VIDIKRON AUTHORIZED PERSONNEL.

RIGHTS, LIMITS AND EXCLUSIONS:

Vidikron limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warranties. Vidikron also excludes any obligation on its part for incidental or consequential damages related to the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

PRE

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual iii

Page 4

EFFECTIVE WARRANTY DATE:

This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date.

IMPORTANT -- WARRANTY REGISTRATION:

Please fill out and mail your warranty registration card. It is imperative that Vidikron knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified.

CONTACT A VIDIKRON AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:

Repairs made under the terms of this Limited Warranty covering your Vidikron video product will be performed at the location of the product, during usual working hours, providing location of product is within normal operating distance from a Vidikron Authorized Service Center. In some instances it may be necessary for the product to be returned to the Vidikron factory for repairs. If, solely in Vidikron’s judgment, location of product to be repaired is beyond normal operating distance of the closest Vidikron Authorized Service Center, or the repair requires the unit be returned to the Vidikron factory, it is the owner’s responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Vidikron Dealer. If this is not possible, contact Vidikron directly for a Return Authorization number and shipping instructions. Vidikron will return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be the responsibility of the owner.

© Copyright 2006 Vidikron, a Runco International Company. This document contains proprietary information protected by copyright, trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer.

Vidikron, Vision, IntelliWide, Imagix, DView and CSMS are trademarks of Vidikron. All other trademarks and registered trademarks used in this document are the property of their respective owners.

Vidikron products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents Pending.

IMINAR

PRE

iv Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 5

ADDITIONAL INFORMATION:

To locate the name and address of the nearest Vidikron Authorized Service Center, or for additional information about this Limited Warranty, please call or write:

VIDIKRON

Attn: Customer Service Department

2900 Faber Street

Union City, CA 94587

Ph: (510) 324-5900

Fax: (510) 324-5905

Toll Free: (888) 4VIDIKRON

VIDIKRON PRODUCT INFORMATION

RETAIN THIS INFORMATION FOR YOUR RECORDS

IMINAR

_________________________________________________________ ________________________________________

Model Purchased Date

____________________________________________________________________________________________________________

Serial Number

____________________________________________________________________________________________________________

Vidikron Authorized Dealer Name

____________________________________________________________________________________________________________

PRE

Address

____________________________________________ __________________ ________________________

City State/Province Postal Code

____________________________________________ _______________________________________________________

Phone Fax

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual v

Page 6

Safety Precautions

Thank you for your purchase of this quality Vidikron video projector! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation.

WAR NING

CAUTION

RISK OFELECTRIC SHOCK

DO NOTOPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Do not use this equipment near water, outdoors or otherwise exposed to the elements.

5. Clean only with a dry cloth.

6. Do not block any ventilation openings.

CAUTION:

SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

IMINAR

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.

9. The 12V trigger only outputs DC 12V signal for triggering. Do not connect to any other power input or output. This could cause damage to this unit.

10. Only use accessories specified by Vidikron.

11. Keep the packing material in case the equipment should ever need to be shipped.

12. Unplug this projector during lightning storms or when it will not be used for an extended period of time.

13. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond rated life could cause them to explode in rare occasions.

14. Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any way, objects have fallen or spilled into the projector, the projector has been exposed to rain or moisture, does not operate normally, or has been dropped.

PRE

vi Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 7

1Table of Contents

TWO YEAR LIMITED WARRANTY ............................................................................................. iii

Safety Precautions ................................................................................................................... vi

1. Introduction ........................................................................................................................ 1

About This Manual ............................................................................................................................................ 1

Target Audience......................................................................................................................................... 1

If You Have Comments About This Manual... .................................................................................. 1

Textual and Graphic Conventions ....................................................................................................... 1

Using This Manual ............................................................................................................................................. 2

Description, Features and Benefits ............................................................................................................. 3

Key Features and Benefits....................................................................................................................... 3

Parts List ....................................................................................................................................................... 4

2. Controls and Functions ...................................................................................................... 5

Vision 10/12 at a Glance ..................................................................................................................................5

Front/Top/Side View................................................................................................................................. 5

Rear/Top/Side View................................................................................................................................... 7

Vision 10/12 Remote Control ........................................................................................................................ 9

3. Installation ........................................................................................................................ 13

Remote Control ................................................................................................................................................ 13

Notes on Batteries ...................................................................................................................................13

PRE

Notes on Remote Control Operation................................................................................................14

Quick Setup ....................................................................................................................................................... 15

Installation Considerations ..........................................................................................................................16

Installation Type ......................................................................................................................................16

IMINAR

Ambient Light ..........................................................................................................................................16

Other Considerations ............................................................................................................................16

Throw Distance.........................................................................................................................................17

Vertical and Horizontal Position ......................................................................................................... 18

Vertical and Horizontal Lens Shift......................................................................................................18

Adjusting the Projection Angle ..........................................................................................................20

Mounting ....................................................................................................................................................21

Folded Optics ............................................................................................................................................21

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual vii

Page 8

Table of Contents

Connections to the Vision 10/12 ................................................................................................................22

Connector Panel Access ........................................................................................................................22

Connecting the Vision 10/12 to Source Components................................................................22

RS-232 Controller Connection ............................................................................................................27

Connecting to the 12-Volt Trigger Output.....................................................................................28

4. Operation .......................................................................................................................... 29

Turning on the Power .................................................................................................................................... 29

Adjusting the Projector Height or Projection Angle ...........................................................................29

Changing the OSD Language ..................................................................................................................... 30

Adjusting the Picture Orientation .............................................................................................................30

Lens Adjustments ............................................................................................................................................31

Focus/Zoom...............................................................................................................................................31

Shift .............................................................................................................................................................. 32

Using the On-Screen Menus ........................................................................................................................32

Main Menu ................................................................................................................................................34

Source Select ............................................................................................................................................34

Aspect Ratio .............................................................................................................................................. 34

Picture Adjust............................................................................................................................................36

Image Option ...........................................................................................................................................42

Installation ................................................................................................................................................. 44

ISF Settings ................................................................................................................................................46

5. Maintenance and Troubleshooting ................................................................................49

Cleaning the Projector ...................................................................................................................................49

Cleaning the Lens ............................................................................................................................................49

PRE

Cleaning the Intake and Exhaust Vents ...................................................................................................50

Lamp Maintenance .........................................................................................................................................51

IMINAR

Lamp Cautions ..................................................................................................................................................51

Lamp Replacement .........................................................................................................................................52

Troubleshooting Tips .....................................................................................................................................53

6. Serial Communications .................................................................................................... 55

RS-232 Connection and Port Configuration ..........................................................................................55

Serial Command Syntax ................................................................................................................................55

7. Specifications .................................................................................................................... 57

Vision 10/12 Specifications ..........................................................................................................................57

Vision 10/12 Dimensions ..............................................................................................................................59

Computer Signal Compatibility ..................................................................................................................60

Video Signal Compatibility ..........................................................................................................................62

viii Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 9

1List of Figures

2-1. Vision 10/12 Top/Front/Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2-2. Vision 10/12 Rear/Top/Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2-3. Vision 10/12 Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3-1. Available Range of the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3-2. Estimating Throw Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3-3. Projector Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3-4. Vertical Lens Shift (Example only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3-5. Horizontal Lens Shift (Example only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3-6. Folded Optics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3-7. HDMI (or DVI) Source Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3-8. Analog RGB Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3-9. Component Video Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3-10. Composite and S-Video Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3-11. RS-232 Control System Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3-12. Connecting the 12-Volt Trigger Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4-1. Adjusting the Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4-2. Focus and Zoom Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4-3. Vertical and Horizontal Lens Shift Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4-4. Vision 10/12 OSD Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4-5. Typical PLUGE Pattern for Adjusting Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

PRE

4-6. Typical Gray Bar Pattern for Adjusting Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4-7. Typical Color Bar Pattern for Adjusting Color Saturation and Tint . . . . . . . . . . . . . . . . . . . . . . . . 38

IMINAR

4-8. Typical Test Pattern for Adjusting Sharpness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

4-9. CIE 1931 Chromaticity Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

4-10. Horizonal and Vertical Keystone Correction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4-11. ISF-Enabled Vision 10/12 Splash Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

7-1. Vision 10/12 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual ix

Page 10

List of Figures

Notes:

IMINAR

PRE

x Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 11

1Introduction

This Owner’s Manual describes how to install, set up and operate the Vidikron Vision Model

10 and Model 12 DLP Projectors. Throughout this manual, the Vidikron Vision

10/Vision 12 DLP Projector is referred to simply as the “Vision 10/12.”

most out of the Vision 10/12.

Vidikron has made every effort to ensure that this manual is accurate as of the date it was printed. However, because of ongoing product improvements and customer feedback, it may require updating from time to time. You can always find the latest version of this and other Vidikron product manuals on-line, at www.vidikron.com.

Vidikron welcomes your comments about this manual. Send them to info@vidikron.com.

Text Conventions: The following conventions are used in this manual, in order to clarify the information and instructions provided:

• Remote and built-in keypad button identifiers are set in upper-case bold type; for

example, “Press EXIT to return to the previous menu.”

• Computer input (commands you type) and output (responses that appear on-screen) is

shown in monospace (fixed-width) type; for example: “To change the aspect ratio to Letterbox, type RRD02.”

• All keys with functional names are initial-capped, set in bold type and enclosed in angle

brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc> and <Tab>.

• <Enter> indicates that you may press either the RETURN or ENTER key on your keyboard

if it has both keys.

In addition to these conventions, underlining, boldface and/or italics are occasionally used to highlight important information, as in this example:

PRE

IMINAR

1.1 About This Manual

Target AudienceVidikron has prepared this manual to help home theater installers and end users get the

If You Have Comments About This Manual...

Textual and Graphic Conventions

Note

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 1

A carriage return must be used after each command or string.

Page 12

Introduction

Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury:

1.2

Using This Manual

Tip

Note

Caution

TIPS highlight time-saving short cuts and helpful guidelines for using certain features.

NOTES emphasize text with unusual importance or special significance. They also provide supplemental information.

CAUTIONS alert users that a given action or omitted action can degrade performance or cause a malfunction.

WARNING

DANGER!

Use the following table to locate the specific information you need in this manual.

WARNINGS appear when a given action or omitted action can result in damage to the equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or death.

IMINAR

If you need... ... Turn to page:

Information about obtaining service iv

General information about the Vision 10/Vision 12 DLP Projector

Installation instructions 13

First-time configuration instructions 30

PRE

Advanced configuration instructions 46

Troubleshooting tips 53

Vision 10/Vision 12 DLP Projector specifications 57

2 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 13

Introduction

Vidikron proudly introduces its most affordable home theater projectors to date -- the Vision Model 10 and Model 12. The Vision 10/12 offers a performance feature set based on the latest generation of DLP™ light engines with Vidikron’s exclusive Imagix™ video processing technology to produce outstanding blacks, superior contrast performance, maximum screen brightness and an accurate color palette.

The Vision 10/12 is equipped with a precision optics package (with manual zoom lens) plus generous horizontal/vertical mechanical lens shift capabilities and electronic keystone correction for flexible placement within virtually any home theater environment. Among the finest attributes of the Vision 10/12 is its ability to meet the rigid Imaging Science Foundation™ (ISF) industry standards for video fidelity and accurate gray scale tracking -vital to achieving true-to-life color reproduction and superior black and white performance.

The Vision 10/12 accepts high-definition, HDCP-compliant signals from today’s latest digital sources, and provides a generous array of component, composite, S-video and VGA inputs, as well as Discrete IR and RS-232 control allowing integration with other audio/video components and automated control systems.

• Native Resolution: 1024 x 576 (Model 10) or 1280 x 720 (Model 12)

• 16:9 Native Aspect Ratio

• High-performance Digital Light Processing (DLP™) engine

• HDMI Input with High-bandwidth Digital Content Protection (HDCP)

•HDTV Compatible

IMINAR

1.3 Description, Features and Benefits

Key Features and BenefitsThe Vision 10/12 offers these key features and benefits:

PRE

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 3

Page 14

Introduction

Parts List Your Vision 10/12 is shipped with the following items. If any items are missing or damaged,

➤

please contact your Vidikron dealer or Vidikron Customer Service at (888) 4VIDIKRON.

• Vision 10/Vision 12 DLP Projector

• AC Power Cord (North America)

• AC Power Cord (Europe)

•Remote Control Unit and two (2), AAA-size batteries

• HD 15-pin VGA to HD 15-pin VGA cable

• DVI-D to DVI-D cable

•DVI-to-HDMI adapter

• Composite video cable (RCA)

• +12-Volt Trigger adapter (3.5-mm, mini phono plug)

• Warranty information and registration card

• Vidikron Vision Model 10/Model 12 Owner’s Operating Manual (this document)

Optional Accessories:

• Ceiling mount kit

IMINAR

PRE

4 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 15

2Controls and Functions

Figure 2-1 and Figure 2-2 show the locations of key Vision 10/12 projector components.

IMINAR

2.1 Vision 10/12 at a Glance

Front/Top/Side View

PRE

Figure 2-1. Vision 10/12 Top/Front/Side View

345678

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 5

Page 16

Controls and Functions

1. TOP IR SENSOR

2. VERTICAL LENS SHIFT DIAL

Shifts the image up or down.

3. INTAKE VENT

4. ADJUSTABLE FEET

Use to adjust the height or projection angle.

5. VIDIKRON LOGO

The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) or upright. To rotate the logo, grip it at the sides, pull it away from the projector and rotate it 180 degrees.

6. FRONT IR SENSOR

7. FOCUS/ZOOM RING

8. EXHAUST VENT

9. HORIZONTAL LENS SHIFT DIAL

10. TEMPERATURE INDICATOR

Flashes blue when the projector is overheated.

11. POWER INDICATOR

Lights solid blue when the projector is in standby mode; flashes blue during cool-down. During normal operation, this LED is off.

IMINAR

PRE

6 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 17

Controls and Functions

Rear/Top/Side View

HDMI

PRE

Figure 2-2. Vision 10/12 Rear/Top/Side View

IMINAR

10 9

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 7

Page 18

Controls and Functions

1. COMPOSITE VIDEO INPUT

Standard composite video input for connecting a VCR, camcorder, laser disc player or other composite video source.

2. S-VIDEO

Standard S-Video input for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR.

3. COMPONENT VIDEO (RCA connectors)

Standard-definition (480i/576i) or high-definition (720p/1080i), YPrPb component input. This is the input for component video from sources such as DVD players.

Tip

4. RGB HD

A 15-pin VGA connection to a personal computer or HD tuner with an RGB output. The Vision 10/12 automatically detects the signal resolution: 480p, 576i, 720p or 1080i.

5. HDMI / Computer Input (Digital)

HDCP-compliant digital video input for connecting a DVD player, personal computer or HD tuner with a DVI or HDMI output.

6. POWER INPUT (100 to 240 VAC)

Connect the Vision 10/12 to power here.

7. RS-232 CONTROL PORT

A female, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system.

8. 12-VOLT TRIGGER (3.5-mm mini phono jack; Tip = +12V; Sleeve = Ground)

For connecting to retractable screens or other devices that respond to 12-volt triggers. Outputs +12 volts / 250 milliamps when the projector is turned on.

9. LAMP COVER

10. EXHAUST VENT

IMINAR

PRE

For best results, do not run your DVD player in progressive mode.

8 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 19

Controls and Functions

Figure 2-3 shows the Vision 10/12 remote control, and the paragraphs that follow describe its functionality.

IMINAR

2.2 Vision 10/12 Remote Control

PRE

Figure 2-3. Vision 10/12 Remote Control

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 9

Page 20

Controls and Functions

1. ON / OFF

Press to turn the projector on or off.

2. IR OUTPUT INDICATOR

Lights when a button is pressed to indicate that an IR signal is being transmitted.

3. Source Selection Buttons:

VIDEO

Press to switch to the Composite video input.

COMP 1 (Component 1)

Press to switch to the Component 1 (480i/576i/720p/1080i) video input.

RGB HD

Press to switch to the RGB HD input.

S-VID 1 (S-Video)

Press to switch to the S-Video input.

COMP 2 (Component 2)

Press to switch to the Component 2 (480i/576i/720p/1080i) video input.

DVI

Press to switch to the Digital Video (HDMI) input.

4. Aspect Ratio Selection Buttons:

ANA (Anamorphic)

For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.

4X3 (Standard 4:3)

Scales the input signal to fit 4:3 display mode in the center of the screen.

L-BOX (Letterbox)

For viewing LaserDisc movies or non-anamorphic DVDs on a 4:3 screen.

PRE

I-WIDE (IntelliWide)

Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display.

CINEMA For viewing 2.35:1 source material on a 1.78:1 (16:9) screen. The upper and lower portions are masked.

C-FILL (CinemaFill)

Stretches a 2.35 image vertically in both directions to fill a 16:9 screen.

IMINAR

5. DEF

Press to restore factory-default settings for the current source.

6. ISF DAY

Press to recall settings for the current input from the “ISF Day” memory preset.

7. ENTER

Press to select a highlighted menu item or confirm a changed setting.

8. MENU

Press this button to access the on-screen display (OSD) controls.

10 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 21

9. Not used.

10. LIGHT Press this button to illuminate the buttons.

11. CUST Press to recall settings for the current input from the “Custom” memory preset.

12. ISF NIGHT Press to recall settings for the current input from the “ISF Night” memory preset.

13. Cursor Keys ( , , , ) Use these buttons to select items or settings, adjust settings or switch display patterns.

14. EXIT Press this button to exit the current menu and return to the previous one.

15. NUMBER KEYS Use these buttons to enter menu passcodes.

Controls and Functions

IMINAR

PRE

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 11

Page 22

Controls and Functions

Notes:

IMINAR

PRE

12 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 23

3Installation

To install batteries in the remote control:

1. Press down the tab on the cover and pull the cover in the direction of the arrow.

2. Insert the included batteries. Ensure that the polarities correctly match the and markings inside the battery compartment.

3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place.

IMINAR

• Do not mix an old battery with a new one or different types of batteries.

• If you will not use the remote control for a long time, remove the batteries to avoid

damage from battery leakage.

3.1 Remote Control

Notes on Batteries• When installing batteries, make sure that the battery polarities are correct.

PRE

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 13

Page 24

Installation

Notes on Remote Control

Operation

The remote control can be used to control the projector within the ranges shown in Figure

➤

3-1.

30°

23'(7 m)

45°

23'(7 m)

30°

IMINAR

Figure 3-1. Available Range of the Remote Control

Note

PRE

• For best results, hold the remote control within 23 feet (7m) of the back or top sensor and aligned within 30°.

• Do not drop the remote control or expose it to moisture or high temperature.

• The remote control may malfunction under a fluorescent lamp. If that occurs, move the projector away from the fluorescent lamp.

• Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the projector.

• If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

• Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the projector, and repeat the operation.

The signal from the remote control can be reflected by the screen.

14 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 25

Installation

Table 3-1 gives a quick overview of the Vision 10/12 installation process. The sections following this one provide detailed instructions.

Note

Table 3-1. Installation Overview

Step Procedure

Choose a location for the projector 16

Connect signal sources to the projector 22

Connect external controller to RS-232 port (optional) 27

Apply power to the projector 29

For rear-screen and/or ceiling-mount installations, select the

proper picture orientation

Lens adjustments: projected image size (zoom), position

(shift) and focus

Installation should be performed by a qualified custom video installation specialist.

For Details, refer to

page...

18, 31

IMINAR

3.2 Quick Setup

Projector calibration: adjust the following for each input, starting with Component SD; save settings when finished:

• Aspect ratio

• Brightness

• Contrast

• Color level

• Tint

• Input position

PRE

34 through 43

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 15

Page 26

Installation

3.3 Installation Considerations

Installation Type Choose the installation type that best suits your needs: front or rear screen, floor mount or

➤

Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs optimally.

inverted mount.

Table 3-2. Projector Installation Options

• Easy to set up

• Can be moved or changed quickly

• Easy to access

• Does not take up audience space

• Projector is unobtrusive

• Projector cannot be accidentally moved

• Projector is completely hidden

• Projector is easily accessed

• Usually good ambient light rejection

Table 3-2 compares these various installation methods.

Advantages Considerations

Front Screen, Floor Mount Installation

• Shares floor space with audience

Front Screen, Inverted Mount (ceiling) Installation

• Installation is more permanent

• Projector access is more difficult

Rear Screen, Floor Mount Installation

• Requires separate room

IMINAR

Rear Screen, Inverted Mount (ceiling) Installation

• Installation cost is usually higher

• Projector is completely hidden

• Usually good ambient light rejection

Rear Screen, Floor Mount with Mirror

PRE

Ambient Light In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your

Other Considerations Other considerations and tips that can help improve your installation:

➤

• Projector is completely hidden

• Usually good ambient light rejection

• Requires less space behind screen than other rear screen installations

images will be noticeably reduced if light directly strikes the screen, such as when a shaft of light from a window or floodlight falls on the image. Images may then appear washed out and less vibrant.

• Keep the ambient temperature constant and below 35°C (95°F). Keep the projector away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the projector circuitry, which may affect performance.

• Keep the projector away from devices that radiate electromagnetic energy such as motors and transformers. Common sources of these include slide projectors, speakers, power amplifiers and elevators.

• Requires separate room

• Installation cost is usually higher

• Requires separate room

• Installation cost is usually higher

16 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 27

an important calculation in any projector installation as it determines whether or not you have enough room to install your projector with a desired screen size and if your image will be the right size for your screen.

You can quickly estimate the throw distance by taking the width of the screen and multiplying it by the lens throw ratio; see

• The Vision 10 has a lens throw ratio of between 1.40 and 1.60.

• The Vision 12 has a lens throw ratio of between 1.42 and 1.65.

The result of this calculation tells you roughly how far back the projector should be positioned from the screen in order to project a focused image large enough to fill the screen.

Figure 3-2.

Installation

Throw DistanceThrow distance is the distance measured from the front of the projector to the screen. This is

For example, with an 8-foot (96-inch) wide screen:

• The Vision 10 has a throw distance range of between 134.4 inches (3.41 meters) and 153.6 inches (3.90 meters).

• The Vision 12 has a throw distance range of between 136.3 inches (3.46 meters) and 158.4 inches (4.02 meters).

Estimating Throw Distance (TD)

Vision Model 10

Minimum TD = Screen Width x 1.40 Maximum TD = Screen Width x 1.60

Vision Model 12

Minimum TD = Screen Width x 1.42 Maximum TD = Screen Width x 1.65

IMINAR

PRE

Figure 3-2. Estimating Throw Distance

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 17

Page 28

Installation

➤

Vertical and Horizontal

Position

Proper placement of the projector relative to the screen will yield a rectangular, perfectly-centered image that completely fills the screen.

Ideally, the projector should be positioned perpendicular to the screen and in such a way that the lens center and screen center are aligned with each other, as shown in

Ceiling Installation

Height

Projection Distance

Lens Center

Ceiling

Figure 3-3.

Screen Lens Center

Floor Installation

Lens Center

Height

Screen

Lens Center

Vertical and Horizontal Lens

Shift

PRE

IMINAR

Projection Distance

Floor

Figure 3-3. Projector Placement

If it is not possible to align the projector and screen as shown in Figure 3-3, you can use the lens shift controls to center the image on the screen. Lens shift is generally expressed as a percentage of the screen height or width, as shown in

Base plate

to lens center =

approx. 4" (depending

on the amount of lens shift)

Figure 3-4 and Figure 3-5.

Screen Center

50% Height

Lens Shift

(0.5 x H)

100% Height

Lens Shift

(1.0 x H)

150% Height

Lens Shift

(1.5 x H)

Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example.

Figure 3-4. Vertical Lens Shift (Example only)

18 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 29

150% Width Lens Shift

(1.5 x W)

100% Width Lens Shift

(1.0 x W)

50% Width Lens Shift

(0.5 x W)

Screen Width (W)

Installation

Screen Center

IMINAR

Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example.

Figure 3-5. Horizontal Lens Shift (Example only)

PRE

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 19

Page 30

Installation

➤

Table 3-3 gives the lens shift limits for the Vision 10 and Vision 12, as percentages and absolute measurements with a 96 x 54 inch (1.78:1) screen.

Table 3-3. Vertical and Horizontal Lens Shift Limits

Vision 10 Vision 12

Lens Shift Limits, as Percentages of Screen Height or Width (Notes 1 and 2)

Adjusting the Projection

Angle

Vertical

(Notes 2 and 3)

Horizontal

(Note 2)

Lens Shift Limits in Inches, with a 96-by-54 inch (1.78:1) Screen

Vertical

Horizontal

Notes:

1. With no vertical or horizontal lens shift, the lens center and screen center are aligned with each other.

2. Vertical shift limits are percentages of the screen height. Horizontal shift limits are percentages of the screen width.

3. Vertical lens shift figures apply to ceiling mount configurations. For floor installations (where the projector is upright), reverse the up/down vertical offset percentages.

IMINAR

Up 40% 46%

Down 60% 63%

Left 8%

Right 8%

Up 21.60 24.84

Down 32.40 34.02

Left 7.68

Right 7.68

If the screen is significantly higher or lower than the projector, you can also tilt the projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling mount. For a floor installation, turn the four adjustable feet on the bottom of the projector to adjust the projector height and/or projection angle.

If you do this, you may need to shift the image or apply keystone correction using the

PRE

on-screen display (OSD) controls, to compensate. For detailed instructions, refer to

On-Screen Menus on page 32.

Using the

20 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 31

installation, one method may be more suitable than another.

Floor Mounting: In typical front and rear screen installations the projector can be mounted to a secure and level surface, such as a table or cart. Carts are useful when moving a projector during a presentation or from site to site. If possible, lock the wheels when it’s in position to prevent it from being moved during a presentation.

Ceiling Mounting: The projector can also be inverted and suspended from the ceiling using a specially designed ceiling mount fixture. This type of mounting is recommended for fixed installations and for those that want the projector out of sight or have a limited space for projector and audience.

Installation

MountingThere are several methods for mounting the projector. Depending on your chosen

Note

to fold the optical path, as shown in be accurately set. If you are considering this type of installation, contact your dealer for assistance.

Screen

Use only the Vidikron-approved ceiling mount kit designed for your projector.

Figure 3-6. The position of the projector and mirror must

Mirror

IMINAR

PRE

Figure 3-6. Folded Optics

Folded OpticsIn rear-screen applications where space behind the projector is limited, a mirror may be used

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 21

Page 32

Installation

➤

3.4 Connections to the Vision 10/12

Connector Panel Access To access the connector panel, press and hold the black door release button. Then, pull

Connecting the Vision 10/12

to Source

Components

Proceed as follows to connect the Vision 10/12 to your video sources, external controller(s) – if present – and AC power.

When connecting your equipment:

• Turn off all equipment before making any connections.

• Use the correct signal cables for each source.

• Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them.

Route all cables through the opening on the rear underside of the

Tip

gently on it to open the door.

Connect your video sources to the Vision 10/12 as shown and described in the sections that follow.

HDMI Connections: The Vision 10/12 has an HDMI input for connecting a DVD player, DTV decoder, personal computer or any other device with a DVI or HDMI output. Connect such devices as shown in

projector. This allows you to keep the connector panel access door closed, making for a more tidy installation.

Figure 3-7.

IMINAR

Tip

Use the HDMI inputs whenever possible. This ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal path, from source component output into the projector.

Note

PRE

The Vision 10/12 supports the VESA Display Data Channel (DDC) standard. This standard provides “Plug and Play” capability; the projector and a VESA DDC-compatible computer communicate their setting requirements, allowing for quick and easy setup.

In order for Plug and Play to work correctly, you must turn on the projector before you turn on the connected computer.

22 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 33

Installation

S-VIDEOVIDEO P

S-VIDEO VIDEOP

COMP 1 COMP 2

CRP

CBYP

RS-232

COMP 1

CRP

CBY

RGB-HD

COMP 2

RGB-HD

HDMI

IMINAR

HDMI or DVI Source

(DVD Player

or HD Set Top Box)

PRE

Note: To connect a DVI source, use the HDMI-to-DVI adapter and DVI cable provided with the projector.

Figure 3-7. HDMI (or DVI) Source Connections

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 23

Page 34

Installation

RGB-HD Connections: The Vision 10/12 has an RGB input for connecting a personal computer or DTV decoder with an RGB output. See

Figure 3-8.

S-VIDEOVIDEO P

S-VIDEO VIDEOP

COMP 1 COMP 2

CRP

CBYP

RS-232

COMP 1

CRP

CBY

COMP 2

IMINAR

RGB-HD

HDMI

PRE

Figure 3-8. Analog RGB Connections

Note

Personal Computer

1. Refer to Computer Signal Compatibility on page 60 for a list of computer signals compatible with the Vision 10/12. Use with signals other than those listed may cause some functions not to work.

2. Some Macintosh computers may require a Macintosh video adapter. Contact your nearest authorized service center or dealer.

3. This Vision 10/12 may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, switch the notebook computer to “CRT only” mode. If you are unsure how to do this, refer to your notebook computer’s user manual.

24 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 35

Component Video Connections: If you have a DVD player or DTV decoder with a component (YPbPr) output, connect it to the COMP 1 or COMP 2 input as shown in Figure 3-9.

Installation

S-VIDEOVIDEO P

S-VIDEO VIDEOP

COMP 1 COMP 2

CRP

RS-232

COMP 1

CRP

CBY

Pr/Cr Pb/Cb Y

COMP 2

RGB-HD

HDMI

IMINAR

Component

Video Source

(DVD Player

or HD Set Top Box)

PRE

Figure 3-9. Component Video Connections

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 25

Page 36

Installation

Composite/S-Video Connections: The Vision 10/12 has S-Video and composite video inputs for connecting a DVD player, VCR, satellite receiver, camcorder, laser disc player et cetera; see

Figure 3-10.

S-VIDEOVIDEO P

Composite S-Video

CRP

S-VIDEO VIDEOP

RS-232

COMP 1 COMP 2

CRP

COMP 1

RS-232

CBY

COMP 2

RGB-HD

IMINAR

RGB-HD

HDMI

PRE

DVD Player, VCR, Satellite Receiver

Figure 3-10. Composite and S-Video Connections

etc.

26 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 37

Installation

Use a standard, 9-pin RS-232 cable to connect a PC or home theater control/automation system (if present) to the RS-232 port on the Vision 10/12; see

Figure 3-11.

For more information about using this connection, refer to Serial Communications on page 55.

S-VIDEOVIDEO P

S-VIDEO VIDEOP

COMP 1 COMP 2

CRP

CBYP

RS-232

COMP 1

CRP

CBY

COMP 2

RGB-HD

345

2 Transmit Data 3 Receive Data 5 Ground All others = not used

RGB-HD

HDMI

RS-232 Controller Connection

Figure 3-11. RS-232 Control System Connection

PRE

IMINAR

To PC or Automation/ Control System

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 27

Page 38

Installation

Connecting to the 12-Volt

Trigger Output

If your home theater contains a retractable screen or other, 12-Volt trigger-activated

➤

equipment, connect it to the 12-volt trigger output on the Vision 10/12 as shown in 3-12.

S-VIDEOVIDEO P

S-VIDEO VIDEOP

COMP 1 COMP 2

CRP

RS-232

COMP 1

CRP

CBY

COMP 2

RGB-HD

Retractable Screen

3.5-mm mini plug

Black = Ground (Sleeve)

Red = +12V (Tip)

or other, 12-volt

trigger-activated equipment

Figure

HDMI

Figure 3-12. Connecting the 12-Volt Trigger Output

IMINAR

PRE

28 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 39

4Operation

1. Turn on your source components.

2. Plug the female end of the power cord into the AC receptacle on the rear of the Vision 10/12 (AC 100V ~ 240V).

3. Connect the other end to your AC power source. The power indicator lights blue to indicate that the Vision 10/12 is in “standby” mode.

4. Press the ON button on the remote control to turn on the projector. The power indicator turns off.

5. After a brief warm-up period (approximately 10 seconds), the Vision 10/12 will start projecting.

When the Vision 10/12 is installed upright, you can adjust the projector height or projection angle by turning the four adjustable feet on the bottom of the projector; see is useful for correcting the angle of projection when the projector is placed on an uneven surface or when the screen is at an angle. You can tilt the projector up to five (5) degrees up or down by adjusting the feet.

The feet are connected to threaded bolts; turn them clockwise to raise the projector or counterclockwise to lower it.

IMINAR

Figure 4-1. This

4.1 Turning on the Power

4.2 Adjusting the Projector Height or Projection Angle

Note

Tilting the projector may cause keystone distortion. To correct this, refer to

Keystone Correction on page 45.

PRE

Figure 4-1. Adjusting the Feet

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 29

Page 40

Operation

4.3

Changing the OSD Language

4.4

Adjusting the Picture Orientation

The Vision 10/12 OSD language is initially set to English, but can also display the menus in French, Italian, German or Spanish. To change the OSD language:

1. Press MENU.

2. Select Installation from the Main Menu.

3. Select Language from the Installation Menu.

4. Press or to select the desired language. The change takes effect immediately.

By default, the Vision 10/12 is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this:

1. Press MENU.

2. Select Installation from the Main Menu.

3. Select Picture Configuration from the Installation Menu.

4. Choose Floor Rear, Ceiling Front or Ceiling Rear, to match the installation method.

IMINAR

PRE

30 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 41

Operation

The Vision 10/12 gives you a great deal of control over the picture size, position and focus. Figure 4-2 shows the location of the focus and zoom controls; Figure 4-3 shows the location of the lens shift controls.

To make the picture larger (zoom in), rotate the zoom ring to the left, toward the Vidikron logo. To make the picture smaller (zoom out), rotate the zoom ring to the right.

Focus

Ring

Zoom Ring

IMINAR

4.5 Lens Adjustments

Focus/ZoomTo focus the projected image, rotate the focus ring left or right.

Focus ring

PRE

Zoom ring

Figure 4-2. Focus and Zoom Controls

Zoom inZoom out

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 31

Page 42

Operation

Shift To change the projected image position, rotate the vertical and/or horizontal lens shift dials.

➤

Note

Lens shift dial (Horizontal)

Do not force the lens shift dials beyond their respective ranges. This may cause the projector to malfunction.

Lens shift dial

(Vertical)

IMINAR

4.6

Using the On-Screen Menus

Figure 4-3. Vertical and Horizontal Lens Shift Controls

PRE

To use the on-screen menus:

1. Press MENU to display the Main Menu.

2. To select a menu item, use the up- or down-arrow buttons ( , ) on the remote control to highlight it.

3. Press the right- or left-arrow button ( or , depending on the OSD position) to access that menu.

4. Use the up- or down-arrow buttons ( , ) to select the setting you want to change.

5. Press the right- or left-arrow button ( , ) to change that setting;

-- OR --

With some settings, you can press ENTER to hide the OSD menus and display a slidebar for that setting only. Then, press the right- or left-arrow button (

6. To return to the previous menu, press EXIT.

, ) to change it.

The Vision 10/12 OSD menus are arranged hierarchically, as shown in Figure 4-4. Depending on the selected input source, some menu options may not be available.

32 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 43

Operation

Picture Adjust

Source Select

Aspect Ratio

Image Option

Installation

Brightness

Contrast

Color

Tint

Sharpness 1, 2, 3, 4, 5

Gamma 1.0, 1.5, 1.8, 2.0, 2.2, 2.35, 2.5, 2.8

Color Temp Native, 5,000K, 5,500K, ... 10,000K

ICC Select Standard, NTSC, HDTV, PAL

White Balance

Save Settings

Load Saved Settings Custom 1, ISF Day, ISF Night

Video

S-Video

Component 1

Component 2

RGB-HD

HDMI/DVI

Anamorphic (16/9)

Standard (4/3) (not available with HD signals)

LetterBox

IntelliWide

Cinema

Cinema Fill

HD/RGB Adjust (available only when RGB-HD input is selected)

Image Position (not available on HDMI input)

Over Scan Adjust 0% to 10%

SDTV Adjust (not available on HDMI or RGB-HD inputs)

Brightness Enhance (on/off)

Lamp Power 200W or 250W

Information (read-only)

Restore Factory Settings

Language

Picture Configuration

OSD Timeout 5 secs., 15 secs. or 60 secs.

OSD Transparent (on/off)

Source Detect Auto or Manual

Auto Power Off (on/off)

Blue Enable (on/off)

OSD Position

Keystone

Fan High Speed Mode (on/off)

PRE

(not available on HDMI or RGB-HD inputs)

R/G/B Gain

R/G/B Offset

Clock

Phase

Reset

Execute Auto Tune

Auto Tune

H Position

V Position

Reset

Chroma Enhance

Video On Film (on/off)

Film Mode

Source, Resolution, V Frequency, H Frequency, Lamp Timer, firmware version

English, French, Italian, German or Spanish

Floor Front, Ceiling Rear, Floor Rear or Ceiling Front

Top Left, Bottom Left, Top Right or Bottom Right

V Keystone

H Keystone

Reset

IMINAR

ISF Settings

Brightness

Contrast

Color

Tint

Sharpness 1, 2, 3, 4, 5

Gamma 1.0, 1.5, 1.8, 2.0, 2.2, 2.35, 2.5, 2.8

Color Temp Native, 5,000K, 5,500K, ... 10,000K

Load Saved Settings Custom 1, ISF Day, ISF Night

White Balance

Save Settings

Lamp Timer Reset

ICC Adjust

ISF Enable (on/off)

Blue Enable (on/off)

Splash Screen Timer 15, 20, 25, 30, ... 60 secs.

Noise Reduction 0, 1, 2, ... 8

(not available on HDMI or RGB-HD inputs)

R/G/B Gain

R/G/B Offset

Standard, NTSC, HDTV, PAL Intensity, Saturation, Hue

Figure 4-4. Vision 10/12 OSD Menu Structure

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 33

Page 44

Operation

Vision Model 10

Picture Adjust

Source select

Aspect Ratio

Image Option

Installation

ISF Settings

Source select

Video

S-Video

Component 1

Component 2

RGB-HD

HDMI/DVI

Main Menu The Main Menu is the starting point for accessing all projector functions.

Source Select From the Main Menu, select Source select to choose a video signal source.

➤

(The ISF Settings menu is grayed out and not accessible until you enter a passcode.)

➤

The active source is indicated by a green square (Q) to its left; in the example at left, Video is the active source.

Aspect Ratio

Anamorphic (16/9)

Standard (4/3)

LetterBox

IntelliWide

Cinema

Cinema Fill

Aspect Ratio To change the aspect ratio (size and shape) of the projected image, select Aspect Ratio from

➤

the Main Menu and press ENTER. Select the appropriate aspect ratio for the type of program material being viewed; refer to

The currently-selected aspect ratio is indicated by a green square (Q) to its left; in the example at left, Anamorphic is selected.

Note

IMINAR

PRE

Table 4-1.

When you change the aspect ratio, save the change to a preset afterwards. Otherwise, the change will be lost when a different input is selected. (The aspect ratio is saved for each input and resolution separately.) For information about saving settings, refer to

Settings on page 42.

Save

34 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 45

Table 4-1. Aspect Ratio Settings

Remote

Aspect Ratio

Control

Key

Operation

Description

Anamorphic

(16/9)

Standard (4/3) 4X3 Standard 4:3 scales the input

ANA Select Anamorphic to view

16:9 DVDs and HDTV

16:9 Image on

16:9 Screen

4:3 Image on

16:9 Screen

Active Image

Area (4:3)

programs in their native aspect ratio. 4:3 images are stretched horizontally to fit a 16:9 screen.

signal to fit in the center of the 16:9 screen. 4:3 is the aspect ratio used by computer monitors, standard television programming and most VHS video cassettes.

IMINAR

This aspect ratio is not available with HD signals.

In Letterbox mode, the image is stretched vertically; the top and bottom portions are "blanked off." Letterbox is best suited for viewing LaserDisc movies or non-anamorphic DVDs on a 4:3 screen.

LetterBox LET

BOX

Letterbox Image on

16:9 Screen

PRE

IntelliWide I-WIDE A 4:3 image is horizontally

scaled in a NON-linear fashion (more on the sides than in the center) to fit a 16x9 screen.

Cinema CINEMA Select Cinema to view 2.35

source material on a 16:9

2.35:1 Image on 16:9 Screen

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 35

screen. The upper and lower portions of the screen are masked, but the geometry of the active image area is not changed.

Page 46

Operation

Table 4-1. Aspect Ratio Settings (continued)

Remote

Aspect Ratio

Cinema Fill C-FILL A 2.35 image is stretched

Control

Key

2.35:1 Image on 16:9 Screen

Description

anamorphically in both directions to fill a 16:9 image.

Picture Adjust Use the controls in the Picture Adjust menu to calibrate your Vision 10/12 for optimum

Picture Adjust

Brightness 0

Contrast 0

Color 0

Tint 0

Sharpness 3

Gamma 2.2

Color Temp 6500K

ICC Select Standard

White Balance

Save Settings

Load Saved Settings

PRE

2.35:1 Image on

16:9 Screen with

Cinema Fill

➤

picture quality.

The Vision 10/12 has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted, industry-recognized standards for optimal video performance and has implemented a training program for technicians and installers to use these standards to obtain optimal picture quality from Vidikron video display devices. Accordingly, Vidikron recommends that setup and calibration be performed by an ISF certified installation technician.

All signal types require separate processing. Therefore, you need to calibrate each input separately. Vidikron recommends calibrating the Vision 10/12 inputs in the following order:

1. Component 1 / Component 2

2. S-Video

3. Video

4. RGB-HD

5. HDMI

IMINAR

Note

Although it may be possible to obtain satisfactory picture quality using the naked eye and regular program material, Vidikron recommends using the following calibration tools for best results:

• External test pattern source -- Sencore VP401 Multimedia Video Generator, Ovation Multimedia test DVD or equivalent.

• A blue filter (provided with many test DVDs), for color level and tint adjustments.

When you change a picture quality setting, save the change to a preset afterwards. Otherwise, the change will be lost when a different input is selected. (Picture quality settings are saved for each input and resolution separately.) For information about saving settings, refer to on page 44.

36 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Installation

Page 47

Connect your test pattern source to the input that you are calibrating and proceed as follows.

Perform the adjustments in the order listed here.

Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an

acronym for “Picture Line-Up Generation Equipment.”) pattern.

Figure 4-5 shows a typical PLUGE

Below Black

bove Black

Operation

Figure 4-5. Typical PLUGE Pattern for Adjusting Brightness

PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes.

IMINAR

Select Brightness from the Picture Adjust menu. Using the left- and right-arrow ( ) buttons, adjust the brightness so that:

• The darkest black bars disappear into the background.

• The dark gray areas are barely visible.

• The lighter gray areas are clearly visible.

• The white areas are a comfortable level of true white.

• The image contains only black, gray and white (no color).

PRE

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 37

Page 48

Operation

Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in

Figure 4-6.

Figure 4-6. Typical Gray Bar Pattern for Adjusting Contrast

Select Contrast from the Picture Adjust menu. Using the left- and right-arrow ( ) buttons, adjust the contrast to a point just below which the white rectangle starts to increase in size.

Note

Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in

IMINAR

Figure 4-7.

gray

PRE

Brightness and contrast controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

yellow

cyan

green

red

magenta

blue

Figure 4-7. Typical Color Bar Pattern for Adjusting Color Saturation and Tint

38 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 49

Select Color from the Picture Adjust menu. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue:

Operation

gray

yellow

cyan

green

red

magenta

blue

Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To set the tint, select Tint from the Picture Adjust menu. While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue.

IMINAR

Note

1. Like the brightness and contrast controls, the color and tint controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

2. Color and tint controls are not available on the HDMI or RGB-HD

inputs.

PRE

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 39

Page 50

Operation

Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture Adjust menu and press ENTER. On your external test pattern source, select a pattern like the one shown in needed, looking for white edges around the transitions from black to gray and different sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them.

Figure 4-8. Adjust as

IMINAR

Figure 4-8. Typical Test Pattern for Adjusting Sharpness

Gamma: The Gamma control determines how gray shades are displayed between minimum

input (black) and maximum input (white) for all signals. A good gamma setting helps to optimize blacks and whites while ensuring smooth transitions for the “in-between” values utilized in other grays.

PRE

Unlike brightness and contrast controls, Gamma allows you to lighten or darken the overall tone of your images without changing the extremes. All images will be more vibrant while still showing good detail in dark areas.

The default Gamma setting is appropriate for most typical home cinema environments.

40 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 51

Color Temperature: To adjust the color temperature, select Color Temp from the Picture Adjust menu and press ENTER. (Color temperature defines the “color of gray.”) The range is from 5,000K to 10,000K, in increments of 500K. The default setting, 6,500K, is appropriate for most situations. Higher settings produce a “bluer” picture; lower ones impart a reddish hue to the image.

For more precise control over the color temperature, you can adjust the x and y coordinates for gray. These define its location on the standard CIE chromaticity graph, shown in 4-9. (CIE stands for “Commission Internationale de l’Éclairage” (International Commission on Illumination), the organization responsible for color measurement and management standards.) Changing either or both of these numbers changes the hue of gray, within a narrow range above or below the selected color temperature; refer to

Table 4-2. Effect of X and Y Coordinates for Color Temperature

Table 4-2.

Figure

Operation

Color Temp 6500K

x 0

y 0

Reset Color Temp

X-adjustment Y-adjustment Result

red hues

blue hues

green hues

yellow hues

To restore the default color temperature, select Reset Color Temp and press ENTER. Press ENTER again to confirm.

1.0

0.9

0.8

0.7

IMINAR

PRE

0.6

0.5

0.4

0.3

0.2

0.1

0.0

0.0 0.1 0. 2 0.3 0. 4 0.5 0. 6 0.7 0.8 0.9 1. 0

Figure 4-9. CIE 1931 Chromaticity Diagram

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 41

D93

D65

10000

8000

D50

6667

5714

5000

4000

3077

2500

2000

Page 52

Operation

White Balance

R Gain 0

G Gain 0

B Gain 0

R Offset 0

G Offset 0

B Offset 0

ICC Select: Choose ICC Select from the Picture Adjust menu to specify the color space (Standard, NTSC, HDTV or PAL) that is appropriate for the source signal, to achieve optimal color balance.

If you select NTSC, HDTV or PAL, you can make further adjustments to individual color space characteristics in the this section. (The Standard color space is factory-set and not adjustable.)

White Balance: To remove any trace of color from the white areas of the projected image, choose White Balance from the Picture Adjust menu and press ENTER.

•Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue, decrease the Gain for that color.

• Offset: Use the Offset controls in the White Balance sub-menu to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red, green or blue, decrease the Offset for that color.

Save Settings: The Vision 10/12 lets you save image quality settings for each input and supported resolution to a preset. You can recall this preset at a later time by simply pressing a button on the remote control or using the Load Saved Settings menu command (see below).

ICC Adjust sub-menu under the ISF Settings menu, described later in

Image Option Use the controls in the Image Option menu to perform advanced image quality adjustments,

PRE

Image Option

HD/RGB Adjust

Image Position

Over Scan Adjust 1%

SDTV Adjust

Brightness Enhance OFF

Lamp Power 250W

Information

Restore Factory Settings

You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected:

• Aspect ratio

• Picture adjustments (brightness, contrast, color saturation, tint, sharpness, gamma, color temperature, ICC selection and white balance settings)

• Image options (SDTV adjust settings, brightness enhance, lamp power)

Load Saved Settings: To recall a preset, choose Load Saved Settings from the Picture Adjust menu and select “Custom1,” “ISF Day” or “ISF Night.” Or, use the corresponding buttons on the remote control.

➤

obtain information about the projector or perform a factory reset.

HD/RGB Adjust: To improve the quality of projected images from a computer or other analog RGB source, select HD/RGB Adjust and press ENTER.

•Clock: If you notice flickering or vertical noise when displaying computer images, adjust the Clock setting to correct the issue.

•Phase: Adjust the phase if the image shows shimmer or “horizontal” noise. Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may notice that you can stabilize the image at more than one point. Use either setting in this case.)

IMINAR

To restore the original Clock and Phase settings, select Reset and press ENTER, then press ENTER again to confirm the reset.

42 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 53

• Auto Tune: Auto Tune automatically adjusts settings to optimize computer images. Auto Tune can be executed either on command or automatically whenever an incoming RGB signal is present. To execute Auto Tune on command, select Execute Auto Tune and press ENTER. To enable automatic Auto Tune, select Auto Tune and set it to ON.

Operation

Note

Image Position: To adjust the horizontal and vertical position of the projected image, select Image Position from the Image Option menu and press ENTER.

•H Position: Use the up- or down-arrow buttons ( , ) to select H Position. Then, use the right-arrow button ( ) to shift the image to the right; use the left-arrow button ( ) to shift the image to the left.

•V Position: Use the up- or down-arrow buttons ( , ) to select V Position. Then, use the right-arrow button ( ) to shift the image up; use the left-arrow button ( ) to shift the image down.

To restore the default image position, select Reset and press ENTER. Then, press ENTER to confirm or EXIT to cancel.

Over Scan Adjust: Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area.

Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Over scan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area.

Auto Tune may take some time to complete, depending on the characteristics of the incoming signal.

IMINAR

Select from 0% to 10% of Overscan, as desired.

For HDTV, DVDs and other video sources, Overscan is generally not necessary or desirable.

SDTV Adjust: To maximize the quality of 480i (composite, S-Video or component) video signals, select SDTV Adjust from the Image Option menu and press ENTER.

• Chroma Enhance: Use Chroma Enhance to add chroma (color information) to the input signal, making colors appear more vibrant and saturated.

• Video On Film: Set Video On Film to ON to repair distortions or abnormalities in a video image.

•Film Mode: Use the Film Mode control to smooth out moving images from interlaced sources. In most cases, the Vision 10/12 detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may wish to force a setting to ensure stable processing for that source.

Brightness Enhance: to amplify the bright areas of the image, select Brightness Enhance and use the right- or left-arrow button ( useful for high ambient light environments or when you use the lower Lamp Power setting (see below).

Lamp Power: Select Lamp Power from the Display Color Menu to adjust the lamp output level. You can choose to run the lamp as bright as possible (250W; this is the default setting) or you can choose the lower setting (200W). Generally, lower lamp output can prolong the life of the lamp, but decreases brightness.

PRE

or ) to set it to ON. Brightness Enhance can be

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 43

Page 54

Operation

Source : Component 1

Resolution: 720 x 480

Vert Freq : 60 Hz

Horz Freq : 31 kHz

Lamp Timer : 720 HR

F/W Version : 226.4.150

Information: Select Information from the Main Menu to see information about the current source, input resolution, horizontal and vertical frequencies, lamp hours and the installed firmware version.

Should you ever need to contact Vidikron Technical Support, this information will help them answer your questions or resolve product performance issues.

Restore Factory Settings: To reset all items in the Image Options menu to their factory default values, select Restore Factory Settings and press ENTER. A warning message appears; press ENTER again to confirm the reset or press EXIT to cancel. After the reset, the projector powers off and restarts.

Installation The Installation menu to change the picture orientation, appearance and behavior of the

Installation

Language English

Picture Configuration Floor Front

OSD Timeout 5 secs

OSD Transparent OFF

Source Detect Auto

Auto Power Off OFF

Blue Enable OFF

OSD Position

Keystone

Fan High Speed Mode ON

➤

PRE

OSD menus, fan speed and other projector settings.

Language: Select Language from the Installation menu and press the right- or left-arrow buttons to select the OSD language (English, French, Italian, German or Spanish).

Picture Configuration: Select Picture Configuration from the Installation menu to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

OSD Timeout: The OSD Timeout setting controls how long the OSD menus stay on screen when no buttons are pressed. Select a time-out period of 5, 15 or 60 seconds.

OSD Transparent: To allow the projected image to show through the OSD menus, select OSD Transparent from the Installation menu and set it to ON.

Source Detect: The Vision 10/12 can automatically detect an incoming signal and switch to that input. To enable automatic source detection, select Source Detect from the Installation menu and set it to Auto.

Auto Power Off: The Vision 10/12 can be set to power off automatically after 15 minutes of no input signal or user input via the remote control. To enable this feature, set it to ON. When you do, a warning message appears on-screen five minutes before the shutdown is to occur. To prevent the projector from powering off, press any key on the remote control.

Blue Enable: Blue Enable removes all red and green color information from the image, simulating a blue filter. You can use it instead of a blue filter when performing color and tint adjustments.

IMINAR

OSD Position: To change the position of the OSD controls, select OSD Position from the Installation menu. Use the up- and down-arrow buttons to select Top Left, Bottom Left, Top Right or Bottom Right, then press ENTER.

44 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 55

Keystone Correction: If the projector and screen are not installed perpendicular to each other, the image may become distorted in a trapezoidal shape, as shown in Select Keystone from the Installation menu to compensate for this.

Horizontal Keystone Correction

Figure 4-10.

Operation

Projector

Positive values compress right side;

Negative values compress left side.

Vertical Keystone Correction

Projected Image

IMINAR

Positive values compress top;

negative values compress bottom.

Figure 4-10. Horizonal and Vertical Keystone Correction

PRE

Note

1. The Vision 10/12 keystone correction can compensate for up to approximately 15 degrees of screen and/or projector tilt.

2. Straight lines or the edges of images may appear jagged while

adjusting the image.

3. Keystone correction is not possible with a 1080i input signal.

Fan High Speed Mode: If the projector is being used in a high-altitude environment, use Fan High Speed Mode to prevent it from overheating. Set Fan High Speed Mode to ON to run the fan at high speed; set it to OFF to run the fan at normal speed.

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 45

Page 56

Operation

ISF Settings Use the ISF Settings menu to perform advanced picture quality adjustments. This menu

ISF Calibration

Brightness 0

Contrast 0

Color 0

Tint 0

Sharpness 3

Gamma 2.2

Color Temp 6500K

Load Saved Settings

White Balance

Save Settings

Lamp Timer Reset

ICC Adjust Standard

ISF Enable OFF

Blue Enable OFF

Splash Screen Timer 60 secs

Noise Reduction 4

➤

should be used by ISF-certified technicians only.

Note

Several controls in this menu are identical to those in the Picture Adjust menu, but are accessible only by entering the ISF Calibration menu passcode. This makes it possible to restore the picture quality settings to what they were when the projector was installed, simply by recalling the “ISF Night” or “ISF Day” preset.

Brightness: Refer to Brightness on page 37.

Contrast: Refer to Contrast on page 38.

Color: Refer to Color Saturation on page 38.

Tint: Refer to Tint on page 39.

Sharpness: Refer to Sharpness on page 40.

Gamma: Refer to Gamma on page 40.

Color Temp: Refer to Color Temperature on page 41.

Load Saved Settings: To recall the Custom1, ISF Night or ISF Day settings, choose Load

Saved Settings from the ISF Calibration menu. Then, select “Custom1,” “ISF Night” or “ISF Day” and press ENTER, or use the corresponding buttons on the remote control.

You must enter a passcode to access the ISF Settings menu.

IMINAR

White Balance: Refer to White Balance on page 42.

Save Settings: For each input and supported resolution, the Vision 10/12 lets you save

image quality settings as presets that you can recall at a later time. You can create up to three presets -- designated “Custom1,” “ISF Day” and “ISF Night” -- per input and resolution.

You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected:

PRE

• Aspect ratio

• Picture adjustments (brightness, contrast, color saturation, tint, sharpness, gamma, color temperature, ICC selection and white balance settings)

• Image options (SDTV adjust settings, brightness enhance, lamp power)

To save image settings in the “ISF Day” or “ISF Night” preset, select Save Settings from the ISF Calibration menu and select “ISF Day” or “ISF Night.” (To save settings to the “Custom1” memory preset, refer to

Lamp Timer Reset: When you replace the projector lamp, you should also reset the lamp hour counter. To do this, select Lamp Timer Reset from the ISF Calibration menu and press ENTER. The Vision 10/12 shows the number of hours the projector lamp has been in service and asks you to confirm or cancel the reset. Press ENTER to confirm or EXIT to cancel.

For detailed lamp replacement instructions, refer to Lamp Replacement on page 52.

Save Settings on page 42.)

46 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 57

ICC Adjust: Use the ICC Adjust controls to customize the stored NTSC, HDTV and/or PAL

G B C Y M

color space characteristics. To do this:

1. Select ICC Adjust from the ISF Calibration menu and press ENTER.

2. Select the color space to modify using the left- or right-arrow buttons.

3. Select a component color (Red, Green, Blue, Cyan, Yellow or Magenta).

For each component color, you can adjust the following:

•Intensity: This slidebar adjusts the intensity -- also known as luminance -- of a given color.

• Saturation: This slidebar adjusts the color saturation level -- the amount of that color in a

video image. Lower settings produce less saturated colors; a setting of “-64” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

•Hue: This slidebar adjusts the red/green color hue for true color reproduction of video signals. For best results, adjust the hue while displaying an external color bar test pattern (

Figure 4-7).

When you have finished customizing the color space, select Store Setting and press ENTER.

ISF Enable: Use ISF Enable to control the display of the ISF logo on the Vision 10/12 splash screen upon power-up; see

Figure 4-11.

Operation

ICC Adjust

Color Type NTSC

Intensity 0

Saturation 0

Hue 0

Store Setting

&$/,%5$7(')25

PRE

Figure 4-11. ISF-Enabled Vision 10/12 Splash Screen

IMINAR

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 47

Page 58

Operation

Blue Enable: Refer to Blue Enable on page 44.

Splash Screen Timer: Press the right- or left-arrow buttons to set the Splash Screen Timer.

This timer controls how long the startup (ISF and Vidikron logo) image stays on-screen after you turn on the projector. Select from 15 to 60 seconds, in 5-second increments.

Noise Reduction: To apply Digital Noise Reduction (DNR) to the input signal, select Noise Reduction from the ISF Calibration menu. Noise reduction is useful for clearing up noisy RGB images such as those from a PC. Adjust as desired using the left- or right-arrow buttons, keeping in mind that reducing noise (which reduces high frequencies) may also “soften” the image.

IMINAR

PRE

48 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 59

5Maintenance and Troubleshooting

• Unplug the power cord before cleaning the projector.

• Avoid using benzene or thinner, as these can damage the finish on the projector exterior.

• Do not use volatile agents, such as insecticides, on the projector.

• Do not leave rubber or plastic objects in contact with the projector for long periods as they may damage the finish of the projector.

• Wipe off dirt gently with a soft flannel cloth.

• For hard-to-remove dirt, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then wipe the projector.

• Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before using.

• Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid cleaning agents, as they may wear the coating film on the surface of the lens.

• The surface of the lens is easily damaged. Do not scrape or hit the lens.

PRE

5.1 Cleaning the Projector

IMINAR

5.2 Cleaning the Lens

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 49

Page 60

Maintenance and Troubleshooting

5.3

Cleaning the Intake and Exhaust Vents

PRE

This Vision 10/12 is equipped with intake and exhaust vents to allow the flow of cool air through the projector and maintain the proper operating temperature.

You should periodically clean the vents by vacuuming them with a vacuum cleaner. Vidikron recommends doing this after every 100 hours of use, or more often if the projector is used in a dirty or smoky location.

To clean the intake and exhaust vents:

1. Press OFF on the remote control to turn off the power. Wait until the cooling fan stops.

2. Unplug the power cord.

IMINAR

Side and front view

Ventilation holes

Power OFF button

3. Remove dust by placing the cleaner hose on the intake and exhaust vents.

50 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 61

Maintenance and Troubleshooting

The projector lamp has a life of 2,000 hours. Maintain proper ventilation to keep the lamp operating throughout its lifetime. Do not subject the projector to unnecessary vibration.

• Lamp replacement is recommended after approximately 2,000 cumulative hours of use or when you notice a significant deterioration in the picture and color quality. To find out how long the currently-installed lamp has been in service, select Image Options menu.

• The actual lamp service life may be less than 2,000 hours depending on the environment in which the projector is used.

• For lamp replacement, please contact your nearest Vidikron authorized service center or Vidikron dealer. Do not attempt to replace the lamp yourself!

Information from the

Caution

This projector uses a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure is caused by excessive shock, improper cooling, surface scratches or deterioration of the lamp due to usage. The period of time up to failure largely varies depending on the individual lamp and the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

When the lamp replacement indicator and on-screen display icon are illuminated or are flashing, replace the lamp with a new one immediately, even if the lamp appears to be operating normally.

IMINAR

If the lamp breaks, glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. As the gas in this lamp contains mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

5.4 Lamp Maintenance

5.5 Lamp Cautions

If the lamp breaks, there is also a possibility that glass particles may spread inside the projector. If this happens, contact your nearest Authorized Dealer to remove the damaged lamp and ensure safe operation.

PRE

Do not remove the lamp unit immediately after turning off the projector. Touching a hot lamp can cause burns or injury. Wait at least one hour after the disconnecting the power cord to allow the surface of the lamp unit to fully cool before removing.

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 51

Page 62

Maintenance and Troubleshooting

5.6

Lamp Replacement

1. Turn off the projector and wait for the cooling fan to stop.

2. Unplug the power cord. Allow the projector to cool down for approximately one hour prior to removing the lamp assembly for replacement.

3. Loosen the two captive lamp cover screws and remove the cover.

4. Loosen the four lamp assembly mounting screws.

5. Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing. As you do so, the lamp cooling interlock switch on the inside of the lamp cavity (near the top) moves to the

PRE

OFF position.

IMINAR

6. Gently slide the new lamp assembly into the lamp cavity. Align the two power connectors at the top of the lamp assembly with the two sockets at the top of the lamp cavity. Press gently on both sides of the lamp assembly to snap it into place. As you do so, the lamp cooling interlock switch returns to the ON position.

7. Tighten the lamp assembly mounting screws.

8. Replace the lamp cover and secure the captive lamp cover screws.

9. Plug in the projector and turn it on.

10. Reset the Lamp Timer to zero. To do this, select Lamp Timer Reset from the ISF Calibration menu and press ENTER. The Vision 10/12 shows the number of hours the projector lamp has been in service and asks you to confirm or cancel the reset. Press ENTER again to confirm.

52 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 63

Maintenance and Troubleshooting

Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the Vision 10/12. If you encounter an issue not described here, please contact your Vidikron dealer or Vidikron Technical Support.

Table 5-1. Troubleshooting Chart

Symptom Possible Cause(s) Solution

The projector does not turn on after initial installation.

The projector is on, but there is no video image on-screen.

A projected image from a DVD is split or otherwise scrambled.

Image is too bright and/or lacks definition in the bright areas of the image.

• The Vision 10/12 is not plugged in or the AC outlet is not active.

• The remote control batteries have run out.

• Incorrect source selection.

• Source component is not turned on.

•DVD player is set to progressive scan mode.

• Contrast is set too high. • Lower the contrast setting.

• Ensure that the Vision 10/12 is plugged in and that the AC outlet is active.

• Replace the batteries.

• Select the correct source.

• Turn on the source component.

• Turn off progressive scan on the DVD player.

• Connect the DVD player to the HD/RGB 1 or HD/RGB 2 input.

IMINAR

5.7 Troubleshooting Tips

Image appears “washed out” and/or dark areas appear too bright.

Colors in the image are swapped; for example, reds appear blue or vice versa.

RGB-HD images appear “noisy.”

The projector will not turn back on after it was powered down, or the image disappears during operation.

• Brightness is set too high. • Lower the brightness

• The Red/Pr, Green/Y or Blue/Pb outputs from the source are connected to the wrong inputs on the Vision

PRE

10/12.

• Clock and Phase settings need adjustment.

• The projector will not turn on for two minutes after power-down, to protect the lamp.

• The lamp has failed or was improperly installed.

setting.

• Ensure that the source outputs are connected to the correct Vision 10/12 input.

• Manually adjust Clock and Phase settings, or perform an Auto-Tune (refer to HD/RGB Adjust on page 42).

• Wait until the cooling fan stops.

• Replace or re-install the lamp.

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 53

Page 64

Maintenance and Troubleshooting

Notes:

IMINAR

PRE

54 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 65

6Serial Communications

To interface the Vision 10/12 with a home theater automation/control system or a PC running terminal emulation software, connect it to your control system or PC as shown in Figure 3-11.

Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 9600, to match that of the Vision 10/12 RS-232 port.

Table 6-1 lists the RS-232 command set. All commands are in ASCII format and must be in UPPERCASE.

When you send a valid command, the Vision 10/12 executes it and acknowledges it with the first three characters of the command followed by “OK;” for example, RRAOK. When you send an invalid command, the Vision 10/12 ignores it and returns the first three characters of the command followed by “NG;” for example, RRXNG.

Table 6-1. Serial Commands

Command Description Reply

RRA00 Saves current settings to the CUSTOM 1 memory

(Note

RRA01 Saves current settings to the ISF Day memory (Note 1) RRAOK

RRA02 Saves current settings to the ISF Night memory

(Note 1)

IMINAR

RRAOK

6.1 RS-232 Connection and Port Configuration

6.2 Serial Command Syntax

RRB00 Recalls the Custom 1 memory settings RRBOK

RRB01 Recalls the ISF Day memory settings RRBOK

RRB02 Recalls the ISF Night settings RRBOK

RRC00 Selects the S-VIDEO input RRCOK

RRC01 Selects the COMPOSITE VIDEO input RRCOK

RRC02 Selects the COMPONENT 1 input RRCOK

RRC03 Selects the COMPONENT 2 input RRCOK

RRC04 Selects the HDMI input RRCOK

RRC05 Selects the RGB input RRCOK

RRD00 Selects the ANAMORPHIC (16:9) aspect ratio RRDOK

RRD01 Selects the STANDARD (4:3) aspect ratio RRDOK

Notes:

1. All image quality settings must be made with the remote control. After the image adjustments are complete, you can use these commands to store the settings in the selected memory.

2. The power on command (PON) will not provide an OK reply; it will instead reply with a random character. For your automation system, simply ensure that you receive a character after the PON command. If you do not get any reply after PON, send PON again.

PRE

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 55

Page 66

Serial Communications

Table 6-1. Serial Commands (continued)

Command Description Reply

RRD02 Selects the LETTERBOX aspect ratio RRDOK

RRD03 Selects the INTELLIWIDE aspect ratio RRDOK

RRD04 Selects the CINEMA (2.35:1) aspect ratio RRDOK

RRD05 Selects the CINEMA FILL aspect ratio RRDOK

RRE00 Turns the projector OFF RREOK

PON Turns the projector ON Random (Note 2)

Notes:

1. All image quality settings must be made with the remote control. After the image adjustments are complete, you can use these commands to store the settings in the selected memory.

IMINAR

PRE

56 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 67

7Specifications

Table 7-1 lists the Vision 10/12 specifications.

Table 7-1. Vision 10/12 Specifications

Projector Type: Digital Light Processing (DLP), single-chip DMD

Native Resolution: Vision Model 10: 1024 x 576 (16:9)

Vision Model 12: 1280 x 720 (16:9)

Aspect Ratios: 4:3, Letterbox, 16:9 Anamorphic, IntelliWide, Cinema,

Cinema Fill

Video Standards: NTSC, PAL, SECAM

Scan Frequency: Horizontal: 15 to 80 kHz

Vertical: 43 to 100 Hz

Picture Size (16:9 Screen): Recommended Width: 72 to 96 in.

Maximum Width: 150 in.

Throw Distance (Factor x Screen Width):

Vision Model 10:

Minimum: Screen Width x 1.40 Maximum: Screen Width x 1.60

Vision Model 12:

Minimum: Screen Width x 1.42 Maximum: Screen Width x 1.65

IMINAR

Horizontal Offset: 8% of screen width left or right

7.1 Vision 10/12 Specifications

Vertical Offset – Vision Model 10: Ceiling-mounted --

60% of screen height below; 40% of screen height above

Floor-mounted --

40% of screen height below;

PRE

Vertical Offset – Vision Model 12: Ceiling-mounted --

Lamp: 250 Watts

Estimated Lamp Life: 2000 hours

Source Inputs: (1) Composite; (1) S-Video; (2) RCA Component (YPbPr); (1)

Control Options: - Discrete infrared remote

RS-232 Communication Parameters:

60% of screen height above

63% of screen height below; 46% of screen height above

Floor-mounted --

46% of screen height below; 63% of screen height above

VGA; (1) HDMI 1.2 with HDCP

- Serial commands via RS-232

9600 bps, no parity, 8 data bits, 1 stop bit, no flow control

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 57

Page 68

Specifications

Table 7-1. Vision 10/12 Specifications (continued)

+12V Output: 0.25 Amps, active when the projector is turned on

Power Requirements: 100 to 240 VAC (auto-sensing), 50/60 Hz, 370 Watts

Operating Environment: 41°F to 95°F (5°C to 35°C), 0% to 90% humidity

Dimensions: See Figure 7-1

Weight (including lens): 27.5 lbs. (12.47 kg)

Brightness and Contrast: Cinema Standards Measurement System (CSMS)

IMINAR

PRE

(non-condensing)

Specifications

- Brightness: 15.9 foot-Lamberts (fL) (Vision Model 10);

16.1 foot-Lamberts (fL) (Vision Model 12)

- Contrast Ratio: 219:1 (Vision Model 10);

224:1 (Vision Model 12)

These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter, Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6,500K and has a minimum of 150 hours of usage. The foot-Lambert (fL) is the unit of measurement used in commercial movie theaters to express image brightness at the screen surface. The Society of Motion Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters. The foot-Lambert measurement is dependent on screen size, screen gain and projector light output.

Home Theater Calibration Specifications

- Light Output: 410 ANSI Lumens (Vision Model 10);

417 ANSI Lumens (Vision Model 12)

- Contrast Ratio: 219:1 (Vision Model 10);

224:1 (Vision Model 12)

These specifications are obtained by calibrating the projector as described above for CSMS measurements.

Industry-Standard Specifications

- Light Output: 780 ANSI Lumens (Vision Model 10);

820 ANSI Lumens (Vision Model 12)

- Contrast Ratio: 2400:1 (Vision Model 10);

2550:1 (Vision Model 12)

These are typical projector brightness and contrast specifications found in most companies’ sales literature. Vidikron includes these measurements in its literature to allow for direct comparison with other manufacturers’ projectors. These measurements are typically taken at 9,000K to 13,000K to get expected performance data when the projector is used in professional, commercial and industrial displays.

Regulatory Approvals: Complies with FCC, CE C-Tick

Limited Warranty: Projector: Two (2) years parts and labor from the date of

delivery to the end user. Lamp: 1000 hours or six (6) months, whichever comes first.

Specifications are subject to change without notice.

58 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 69

Specifications

Figure 7-1 shows the Vision 10/12 dimensions.

Rear View

15.66in

Side View Side View

16.06in

398.0mm

9.12in

231.7mm 166.3mm

6.54in

16.99in

431.6mm

16.90in

429.4mm

IMINAR

7.2 Vision 10/12 Dimensions

Front View

4.09in

103.9mm

PRE

6.48in

164.6mm 408.0mm

Bottom View

3.42in 3.42in 87mm 87mm

Figure 7-1. Vision 10/12 Dimensions

6.40in

162.6mm

0.89in

22.8mm164.6mm

6.48in

7.15in

181.8mm

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 59

Page 70

Specifications

7.3 Computer Signal Compatibility

The Vision 10/12 can display video signals from a variety of computer sources via its RGB-HD and HDMI inputs. It is compatible with the three most common sync modes -- sync-on-green, composite sync and RGB with separate sync -- as well as XGA display adapters that use advanced intelligent compression.

Table 7-2 lists the signal types that are compatible with the Vision 10/12, and indicates which of those are VESA standards.

Table 7-2. Computer Signal Compatibility Chart

PC/MAC/

PC VGA 640 x 350 27.0 60 Upscale

Resolution

720 x 350 27.0 60

640 x 400 27.0 60 √

IMINAR

720 x 400 27.0 60 √

Horizontal Frequency

(kHz)

31.5 70

37.9 85 √

31.5 70

31.5 70 √

37.9 85 √ √

31.5 70 √

Vertical

Frequency

(Hz)

VESA

Standard

HDMI

Support

Display

PRE

Notes:

1. This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, switch the notebook computer to “CRT only” mode. If you are unsure how to do this, refer to your notebook computer’s user manual.

2. When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.

3. Interlaced video signals received through the RGB input may not display correctly. If this occurs, use the Component 1, Component 2, S-video or Composite video input instead.

37.9 85 √ √

640 x 480 26.2 50 √

31.5 60 √

36.8 70 √

37.9 72 √ √

37.5 75 √ √

43.3 85 √ √

47.9 90 √

53.0 100 √

60 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 71

Table 7-2. Computer Signal Compatibility Chart (continued)

Specifications

PC/MAC/

PC SVGA 800 x 600 31.4 50 √ Upscale

PC SVGA 800 x 600 53.7 85 √ √ Upscale

PC XGA 1024 x 768 35.5 43

Resolution

Horizontal Frequency

(kHz)

35.1 56 √ √

37.9 60 √ √

44.5 70 √

48.1 72 √ √

46.9 75 √ √

56.8 90 √

64.0 100 √

40.3 50

48.4 60

56.5 70

60.0 75

68.7 85

73.5 90

Vertical

Frequency

(Hz)

IMINAR

VESA

Standard

√ √

HDMI

Support

√

Display

True

77.2 96

80.6 100

MAC 13” VGA 640 x 480 34.9 67 Upscale

MAC 16” SVGA 832 x 624 49.6 75

MAC 19” XGA 1024 x 768 48.4 60

Notes:

2. When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.

3. Interlaced video signals received through the RGB input may not display correctly. If this occurs, use the Component 1, Component 2, S-video or Composite video input instead.

PRE

√

True

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 61

Page 72

Specifications

7.4 Video Signal Compatibility

Table 7-3 lists numerous common video signal formats and indicates which input(s) on the Vision 10/12 can accept a given format.

Table 7-3. Video Signal Compatibility Chart

Resolution

NTSC 640 x 480i 15.73 59.94/

Video

PAL 768 x 576i 15.63 50 √ √ √ √

SECAM √ √ √ √

NTSC-

4.43

PAL-M

PAL-N

NTSC-J

PAL-60

NTSC-

EDTV 480p 720 x 480p 31.5 59.94/

HDTV 1080i/501920 x

IMINAR

576p 720 x 576p 31.3 50 √ √ √ √

1080i

H-Freq

(kHz)

28.1 50 √ √ √ √

V-Freq

(Hz)

Comp. 1Comp. 2S-

√ √ √ √

(not supported)

√ √ √ √

Compatible Inputs (Note 1)

Video

posite

(adjustment required)

Com-

VGA HDMI

1080i/

720p/501280 x

PRE

720p/

HTPC (Note

Notes:

1. The Component 1 and Component 2 inputs accept both analog (YPbPr) and digital (YCbCr) signals.

2. HTPC = Home Theater PC

720p/481280 x

2) 720p/

576p/481024 x

720p

576p

33.8 59.94/ 60

37.5 50 √ √ √ √

45.0 59.94/ 60

48 √

75 √

48 √

62 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

√ √ √ √

Page 73

Page 74

RUMA-011175

rev. 08-14-06 v2.0

Vidikron 2900 Faber Street Union City, CA 94587 510-324-5900 Fax 510-324-5905 1-888-4-VIDIKRON www.vidikron.com

SERIAL NUMBER

Vidikron Vision 12, Vision 10 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TWO YEAR LIMITED WARRANTY

Safety Precautions

1Introduction

1.1 About This Manual

Target AudienceVidikron has prepared this manual to help home theater installers and end users get the

If You Have Comments About This Manual...

Textual and Graphic Conventions

Using This Manual

1.3 Description, Features and Benefits

Key Features and BenefitsThe Vision 10/12 offers these key features and benefits:

Parts List Your Vision 10/12 is shipped with the following items. If any items are missing or damaged,

2Controls and Functions

2.1 Vision 10/12 at a Glance

Front/Top/Side View

Figure 2-1. Vision 10/12 Top/Front/Side View

Rear/Top/Side View

Figure 2-2. Vision 10/12 Rear/Top/Side View

2.2 Vision 10/12 Remote Control

Figure 2-3. Vision 10/12 Remote Control

3Installation

3.1 Remote Control

Notes on Batteries• When installing batteries, make sure that the battery polarities are correct.

Figure 3-1. Available Range of the Remote Control

Table 3-1. Installation Overview

3.2 Quick Setup

3.3 Installation Considerations

Installation Type Choose the installation type that best suits your needs: front or rear screen, floor mount or

Table 3-2. Projector Installation Options

Ambient Light In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your

Other Considerations Other considerations and tips that can help improve your installation:

Throw DistanceThrow distance is the distance measured from the front of the projector to the screen. This is

Figure 3-2. Estimating Throw Distance

Figure 3-3. Projector Placement

Figure 3-4. Vertical Lens Shift (Example only)

Figure 3-5. Horizontal Lens Shift (Example only)

Table 3-3. Vertical and Horizontal Lens Shift Limits

MountingThere are several methods for mounting the projector. Depending on your chosen

Figure 3-6. Folded Optics

Folded OpticsIn rear-screen applications where space behind the projector is limited, a mirror may be used

3.4 Connections to the Vision 10/12

Connector Panel Access To access the connector panel, press and hold the black door release button. Then, pull

Figure 3-7. HDMI (or DVI) Source Connections

Figure 3-8. Analog RGB Connections

Figure 3-9. Component Video Connections

Figure 3-10. Composite and S-Video Connections

RS-232 Controller Connection

Figure 3-11. RS-232 Control System Connection

Figure 3-12. Connecting the 12-Volt Trigger Output

4Operation

4.1 Turning on the Power

4.2 Adjusting the Projector Height or Projection Angle

Figure 4-1. Adjusting the Feet

Changing the OSD Language

Adjusting the Picture Orientation

4.5 Lens Adjustments

Focus/ZoomTo focus the projected image, rotate the focus ring left or right.

Figure 4-2. Focus and Zoom Controls

Shift To change the projected image position, rotate the vertical and/or horizontal lens shift dials.

Using the On-Screen Menus

Figure 4-3. Vertical and Horizontal Lens Shift Controls

Figure 4-4. Vision 10/12 OSD Menu Structure

Source select

Aspect Ratio

Main Menu The Main Menu is the starting point for accessing all projector functions.

Table 4-1. Aspect Ratio Settings

Picture Adjust

Figure 4-5. Typical PLUGE Pattern for Adjusting Brightness

Figure 4-6. Typical Gray Bar Pattern for Adjusting Contrast

Figure 4-7. Typical Color Bar Pattern for Adjusting Color Saturation and Tint

Figure 4-8. Typical Test Pattern for Adjusting Sharpness

Table 4-2. Effect of X and Y Coordinates for Color Temperature

Figure 4-9. CIE 1931 Chromaticity Diagram

White Balance

Image Option

HD/RGB Adjust

Installation