Videx 4836, 4000 Series, 4836-1, 4836-0, 4836-2 User Manual

66250430 - V2.0 - 15/05/18

- 1 -

4000 Series

Art.4836 - Installation instructions

Art.4836 Speaker unit for audio door entry kits or little systems

A

B

B

C

Fig. 1 Front

4836-0
4836-1
4836-2

4836-1D
4836-2D

Made in Italy

Stainless Steel Matte
Aluminium
High Brass

CC1P1P2SS1312

P3

P4

F

D

E

G

Fig. 2 Back

DESCRIPTION

Speaker unit for audio door entry kits or little systems.
The unit circuitry includes:
a. The transmitting amplier with condenser microphone and

volume control;
b. The receiving amplier and volume control;
c. 2 LEDs to illuminate the name plate (except Art.4836-0 model);
d. The lock release relay to enable the electric lock;
e. The modulated tone generator;
On speaker units Art.4836-0, Art.4836-1 and Art.4836-2 the P3
and P4 terminals will not be available.

LEGEND

A

Loudspeaker

B

Push buttons

C

Card name holders

D

Loudspeaker volume

E

Microphone volume

F

Microphone

G

Connection terminals

CONTROLS

Loudspeaker volume

Adjust the loudspeaker volume.
Rotate clockwise to increase or anti-clockwise to decrease

Microphone volume

Adjust the microphone volume.
Rotate clockwise to increase or anti-clockwise to decrease

AVAILABLE VERSIONS AND BUTTONS LAYOUT

Art.4836-0

1

Art.4836-1

1

2

Art.4836-2

13

Art.4836-1D

13

4 2

Art.4836-2D

ADHESIVE GASKET PLACEMENT

Apply the Y seal as shown in Fig. 3.

ANTITAMPERING LOCKS FIXING

Fit the anti-tampering locks

W

as shown in Fig. 4.

Y

G

Fig. 3

W

Fig. 4

66250430 - V2.0 - 15/05/18

- 2 -

4000 Series

Art.4836 - Installation instructions

Art.4836 Speaker unit for audio door entry kits or little systems

HOW TO REMOVE/INSERT THE CARD NAME HOLDER

• To avoid damage to the module front plate, mask the side that

will be in contact with the screwdriver blade;

• Insert the screwdriver (at side) into the card-holder hole as

shown in Fig. 5;

• Move the screwdriver to the left as shown in Fig. 6 to extract

the card name holder;

• Edit the card name then replace it inside the holder and ret:

insert the holder inside its housing from the left or right side

then push the other side until it clips into place.

Fig. 5 Fig. 6

CONNECTION TERMINALS SIGNALS

C Push buttons common

C1 Electronic call tone output (active only on call)

P1

Output call button 1
(available on all versions except Art.4836-0)

P2

Output call button 2
(available only on Art.4836-2 and Art.4836-2D versions)

S

Normally open relay contacts (the contact between S and
S1 is closed when the unit receives the “door open” signal

S1

Power supply input 0V

3 Speech Ground output

1

Speech input
“Door Open” signal
Power supply input 13Vac

2 Speech output

P3

Output call button 3
(available only on Art.4836-1D and Art.4836-2D versions)

P4

Output call button 4
(available only on Art.4836-2D version)

TECHNICAL SPECIFICATION
Power Supply: 13Vac

Power consumption: Stand-by: approx. 25mA

During a call: approx. 150mA
During a conversation: approx 70mA

Working Temperature: -10 +50 °C
CLEANING OF THE PLATE

Use a clean and soft cloth. Use moderate warm water or non-ag­gressive cleansers.

Do not use:

• abrasive liquids;

• chlorine-based liquids;

• metal cleaning products.

66250430 - V2.0 - 15/05/18

- 3 -

Serie 4000

Art.4836 - Istruzioni di installazione

Art.4836

Portiere elettrico per kit citofonici o piccole installazioni in genere

A

B

B

C

Fig. 1 Fronte

4836-0
4836-1
4836-2

4836-1D
4836-2D

Made in Italy

Stainless Steel Matte
Aluminium
High Brass

CC1P1P2SS1312

P3

P4

F

D

E

G

Fig. 2 Retro

DESCRIZIONE

Portiere elettrico per kit citofonici o piccole installazioni in genere.
La sua elettronica comprende:
a. L’amplicatore di trasmissione con microfono a condensatore

e regolazione del volume;
b. L’amplicatore di ricezione con altoparlante da 0,5W e regola-

zione del volume;
c. 2 LED d’illuminazione cartellini (escluso Art.4836-0);
d. Il relè d’asservimento per l’attivazione della serratura elettrica;
e. Il circuito di generazione della nota elettronica.
Nelle versioni Art.4836-0, Art.4836-1 e Art.4836-2 non sono pre­senti i morsetti P3 e P4.

LEGENDA

A

Altoparlante

B

Pulsanti di chiamata

C

Porta cartellini

D

Volume altoparlante

E

Volume microfono

F

Microfono

G

Morsetteria di connessione

REGOLAZIONI

Volume altoparlante

Regolazione del volume dell’altopalralte.
Ruotare in senso orario per aumentare o antiorario per diminuire

Volume microfono

Regolazione del volume del microfono.
Ruotare in senso orario per aumentare o antiorario per diminuire

VERSIONI DISPONIBILI E ORDINE PULSANTI

Art.4836-0

1

Art.4836-1

1

2

Art.4836-2

13

Art.4836-1D

13

4 2

Art.4836-2D

APPLICAZIONE GUARNIZIONE ADESIVA

Applicare la guarnizione adesiva Y come mostrato in Fig. 3.

INSERIMENTO FERMI ANTIEFFRAZIONE

Inserire i fermi anti-erazione

W

come mostrato in Fig. 4.

Y

G

Fig. 3

W

Fig. 4