Videx 3600 Series 3618 Installation Instructions Manual
66251030-EN - V2.1 - 15/06/16
1
3600 Series
Art.3618 - Installation instructions
161
178
218
62
46
Fig. 1
1
2
3
4
ON
Fig. 2
DESCRIPTION
Videophone (with hands free facility) using 3.5” full colour active matrix LCD monitor for traditional video door entry systems using
composite (coax cable) or balanced (twisted pair) video signal to bring the video signal. Are available “door open” , “answer/camera
recall/push to talk”, “privacy/call reject/service” buttons plus 3 LED’s give visual signalling relative to the videophone operation.
Controls: loudspeaker volume, call tone volume, picture contrast, brightness and hue.
Programmable privacy duration, melody, number of rings, door opening time and video mode. Input for electronic call tone.
The Art.3618 is for surface mount (requires the Art.5980 connection board plus wall mounting plate). It can be used in all the
systems where are used the Art.3411, Art.3412, Art.5418, Art.SL5418 or Art.5412 but requires an additional wire for 12Vdc power
supply and cannot be connected in parallel with the mode is mentioned above in the same apartment.
PUSH BUTTONS
1. On an incoming call, operation of this button allows the user to answer and converse with the visitor in hands free
mode. The relevant LED will illuminate. You can answer also by the handset.
2. If operated when system is in standby (no Call) camera recall will be activated and the relevant LED will illuminate.
3. When in conversation (monitor on), momentary operation of the button will switch the videophone o. The videophone will also automatically switch o after a time delay if the button is not pressed. The relevant LED will
switch o.
4. When in conversation (monitor on), pressing and holding the button for more than 3 seconds will switch the videophone into SIMPLEX speech mode. Press and hold the button to speak to the caller (The LED will ash rapidly),
release the button to listen (The LED will ash slowly). If the button is not pressed for 10 seconds the videophone
will switch o. The videophone will revert to duplex speech when another call is made.
During a call, operation of this button will activate the “door open” relay. On the display (top centre) will be signalled
the door opening. The LED of the button will illuminate if terminal 19 has been properly connected i.e. to a door
contact to monitor the door status.
Art.3618 Videophone for traditional video systems using coax video
signal or balanced video signal
66251030-EN - V2.1 - 15/06/16
2
3600 Series
Art.3618 - Installation instructions
PUSH BUTTONS
1. During a call, press this button to reject the call.
2. When the system is in stand-by, short pressing of this button enables / disables the privacy service. The relevant
LED will illuminate when the privacy service is enabled. When privacy is enabled calls will not be received.
3. When the system is in stand-by, press this button until the videophone switches on emitting a beep to enter into
the programming menu that allows to set the privacy duration, the call tone volume, the melody selection, the
number of rings and the door opening time.
4. During a conversation, press this button to enter the adjustment menu that allows to set the speech volume, the
brightness, the contrast and the hue.
5. During a conversation, press and keep pressed this button until the videophone emits a beep: the auxiliary output
is operated and the terminal “12/SB” is linked to ground for 2 seconds.
CONTROLS AND PROGRAMMING
The adjustments and settings are carried out through the two OSD menus that are described below. For video mode setup (coax or
balanced) operate the 4 way dip switch on the rear side of the videophone.
The Art.3618 has an additional programming related to the system in which it is used: 890 Mode (for systems in which it is used the
control unit Art.890/Art.890N) and 4838 Mode (for systems in which it is used the speaker unit Art.4838).
The videomonitor has two dierent menus for programming and adjustment functions:
1. One menu operates when the system is in stand-by and allows to set:
• The privacy duration;
• The melody volume;
• The melody type;
• The number of rings;
• The door opening time;
2. The second menu operates when the system is turned ON (during a conversation or a camera recall) and allows to set;
• Speech volume;
• Brightness;
• Contrast;
• Hue;
MENÙ 1
• When the system is in stand-by (monitor turned OFF) press and hold pressed the “
” button until the monitor switches emitting
a beep to enter the programming menu.
• TThe OSD menu appears on the display: the top of the screen shows “menu” followed by the available function icons, the bottom
of the screen shows the currently selected function value on the left, the currently selected function icon in the middle and the
next function icon on the right side.
• The rst function available is the privacy duration (max 20 hours): press as many times or hold pressed the “ ” button to increase or the “
” button to decrease the duration of a half an hour each step (signalled by a beep).
• Press the “
” button to store the new value and to enter the following programming function.
• The second function is the melody volume: press as many times or hold pressed the “
” button to increase or the “ ” button
to decrease the melody volume level (signalled by a beep).
• Press the “
” button to store the new value and to enter the following programming function.
• The third function is the melody type: press the “
” button to hear and select the previous melody or the “ ” button to hear
and select the following melody.
• Press the “
” button to store the new value and to enter the following programming function.
• The fourth and last programming function is the number of rings (max 9): press as many times or hold pressed the “ ” button
to increase or the “
” button to decrease the number of rings.
• Press the “
” button to store the new value and to enter the following programming function.
• The fth programming function is the door opening time (max 99 seconds): press as many times or hold pressed the “ ” button to increase or the “
” button to decrease the number of rings.
• Press the “
” button to store the new value and exit the programming menu, the monitor turns OFF .
Art.3618 Videophone for traditional video systems using coax video signal or balanced video signal
66251030-EN - V2.1 - 15/06/16
3
3600 Series
Art.3618 - Installation instructions
MENÙ 2
• When the monitor is turned ON (conversation or camera recall) press the “
” button to enter the adjustment menu.
• The OSD menu appears on the display: the top of the screen shows “menu” followed by the allowed function icons, the bottom
of the screen shows the currently selected function value on the left, the currently selected function icon in the middle and the
next function icon on the right side.
• The rst adjustment is the speech volume: press as many times or hold pressed the “
” button to increase or the “ ” button
to decrease the speech volume level (signalled by a beep).
• Press the “
” button to store the new value and to enter the following programming function.
• The second adjustment is the brightness: press as many times or hold pressed the “
” button to increase or the “ ” button
to decrease the brightness level (signalled by a beep).
• Press the “
” button to store the new value and to enter the following programming function.
• The third function is the contrast: press as many times or hold pressed the “
” button to increase or the “ ” button to de-
crease the contrast level (signalled by a beep).
• Press the “
” button to store the new value and to enter the following programming function.
• The fourth and last function is the hue: press as many times or hold pressed the “
” button to increase or the “ ” button to
decrease the hue level (signalled by a beep).
• Press the “
” button to store the new value and exit the programming menu the monitor goes back to shown standard mes-
sages for conversation.
SYSTEM MODE
• To set the 890 Mode (for systems where it is used the control unit Art.890/Art.890N) unplug the ribbon cable from the PCB connection board Art.5980 then plug it again keeping pressed the button “
” until the related LED switches on for approx 1 second.
• To set the 4838 Mode (for systems where it is used the speaker unit Art.4838) unplug the ribbon cable from the PCB connection
board Art.5980 then plug it again keeping pressed the button “
” until the related LED switches on for approx 1 second.
TO SET THE VIDEO MODE
The videophone can operate with either composite video signal (coax cable)
or balanced video signal (two wires).
Switches 1 & 2 of SW2 are used to set video mode while switches 3 & 4 are for video termination. When more videophone
have a pass through connection for the
video signal, you must enable the video
termination only for the last videophone.
VIDEO MODE
Switches 1,2 Mode
Coax
Balanced
75 OHM VIDEO TERMINATION
Switches 3,4 Termination
Enabled
Disabled
Art.3618 Videophone for traditional video systems using coax video signal or balanced video signal
Loading...