Videotel 4022 Operation Manual
Packing List
Model 4022 Industrial DVD Player Operation Manual
With your order you should receive...
1 - 6’ Power Cord (1)
1 - Power Supply (2)
1 - 3’ RCA Video/Audio Cable (3)
1 - Remote (4) (1 remote is included
with every 4 players purchased)
1 - DVD Player (5)
(1) (2) (3) (4) (5)
Basic Operation Of Player
The 4022 comes shipped to you set up for “Auto Start”,
“Auto Play” and “Auto Repeat”. This means once you have
connected the player to a TV and power, all you have to do is
open the tray (16) (by pressing the Open/Close button (17)),
load a disc and close the tray (by pressing the Open/Close
button or by manually pushing the tray in). Within about
15 seconds the movie should begin to play and the player
will be automatically set to auto repeat. When the DVD is in
“Auto” mode the light on the front (18) will be green.
Basic Operation Of Player - Remote
(16)
(19)
(17)
(18)
(21)
Since the “Auto” option was designed to be as simple as possible we have removed functionality from a majority of the buttons on the remote control. If you
plan to only use this unit to play movies over and over, you will probably
never need the remote. However there are a few useful functions that are still
active. Since some of our customers use 10 to 100 players in the same room we
designed the remote to have single function buttons. For example, the Power button (19) ONLY turns the power off. This eliminates the issue of wanting to turn off
100 players and pressing the button once turns off, say 60, and pressing it again
turns off another 20, but turns 30 of the “off” players back on. You can press the
power button as many times as you like and it will only turn power off. The Play/
Pause button (20) ONLY turns players back on. Please note, when you turn players
on they will automatically begin playing from the beginning of the movie unless
you activate the “Resume On” feature (see instructions under “Manual Mode”).
The Open/Close button (21) ONLY opens the disc tray. The “SEL” button (22) ONLY
closes the disc tray.
Basic Operation Of Player - Power Off & Notes
If you wish to turn the power off to the player you can press the Power button
on the remote or on the front of the player. When the power to the player is off,
the light on the front will turn red. The player is powered down and only the light
remains on (uses almost no electricity). If you see the light turn orange, you have
put the player into “Manual Mode”. You can toggle between “Auto” and “Manual
Mode” by holding the Power button on the player for about 5 seconds.
(22)
(20)
Operation Of Player In “Manual Mode”
If you have a disc that won’t auto play or you want to use the remote for other
functions, you need to put the player in “Manual Mode”. To do this, simply hold
the Power button on the front of the player for about 5 seconds. The light should
turn orange. Once in “Manual Mode”, you can use the remote to preform other
functions.
(33)
(23) “Prev” allows you to skip backwards (by chapter) through the DVD.
(24) “Next” allows you to skip forwards (by chapter) through the DVD.
(25) “FR” allows you to rewind the DVD*.
(26) “FF” allows you to fast forward the DVD*.
*each time you press the button, the speed will change (2x,4x,8x,16x,32x,64x)
(27) “Volume +” adjusts the volume output higher.
(28) “Volume -” adjusts the volume output lower.
(29) Arrows keys work normally and are typically only used if you need to
navigate through a menu on a DVD.
(30) “ZOOM” enlarges the picture 1.5 times, 2 times and 3 times its size.
(31) “SR” rewinds the movie slowly in 1/2, 1/4 and 1/8 speeds.
(32) “FR” fast forwards the movie slowly in 1/2, 1/4 and 1/8 speeds.
(33) “MENU” controls the menu of your DVD.
(34) “DISPLAY” shows the current chapter, current title, time played and time
remaining.
(35) “STOP” Pressing this once will stop the movie and allow you to press play
at a later time and resume your spot in the movie. If you press it twice and
then press play, the movie will start from the beginning.
(36) “PLAY/PAUSE” toggles between play and pause.
(37) “SUB-T” rotates through all the available subtitle languages on the DVD
(the subtile option may need to activated on the DVD’s menu).
(38) “GOTO” allows you to select a specific chapter in your movie. Press the
“GOTO” button, then press the “+10key” (42) & any number button (43) to
select your desired chapter, then press “SEL”.
(39) “AUDIO” rotates through the different audio options on your dvd.
(40) “SETUP” brings up the on screen display for the DVD player. This allows you
to change audio settings, video outputs and set a parental security code.
(41) “STEP” pauses the movie and each time you press the button, the movie
advances by 1 frame.
(23) (24)
(25) (26)
(32)
(31)
(43)
(42)
(30)
(28) (27)
(29)
(34)
Switching your player to resume play after powering off
The 4400 has the option to start the disc over once you turn power back on or to
resume play wherever the movie was playing last. To disable and re-enable this
option you need to first remove the DVD. Close the tray and make sure the light
on the front is orange, if its green, press and hold the Power button on the player
for 5 seconds. Now press the “ZOOM” button. An on screen display will show “RESUME ON” (which will continue play) or “RESUME OFF” (which will start the movie
over from the beginning).
Switching your player to not auto repeat
The 4022 has the option to disable the “Auto Repeat” feature (when a disc is at its
end, it will start over and automatically loop). To toggle between these 2 settings
you need to first remove the DVD. Close the tray and make sure the light on the
front is orange, if its green, press and hold the power button on the player for 5
seconds. Now press the “TITLE” button. An on screen display will show “REPEAT
ON” (which will loop the disc continuously) or “REPEAT OFF” (which will play the
movie only once and then return to the disc menu).
(41)
(40)
(35)
(39)
(36)
(37)
(38)
Loading...