Videotec UPTIRPS230 User Manual [en, de, fr, it]

UPTIRPS230

ULISSE external power supply for IR360 versions

EN

English - Instructions manual

IT

Italiano - Manuale di istruzioni

FR

Français - Manuel d’instructions

DE

Deutsch - Bedienungslanleitung

UPTIRPS230

External power supply for ULISSE with infrared illuminators

Instructions manual - English - EN

1 About this manual

Before installing and using this unit, please read this
manual carefully. Be sure to keep it handy for later
reference.

1.1 Typographical conventions

DANGER!
High level hazard.
Risk of electric shock. Disconnect the
power supply before proceeding with any
operation, unless indicated otherwise.

WARNING!
Medium level hazard.
This operation is very important for the
system to function properly. Please read
the procedure described very carefully and
carry it out as instructed.

INFO
Description of system specications.
We recommend reading this part carefully
in order to understand the subsequent
stages.

2 Notes on copyright and information on trademarks

The quoted names of products or companies are
trademarks or registered trademarks.

3 Safety rules

The manufacturer declines all responsibility
for any damage caused by an improper use
of the appliances mentioned in this manual.
Furthermore, the manufacturer reserves
the right to modify its contents without any
prior notice. The documentation contained
in this manual has been collected with great
care, the manufacturer, however, cannot
take any liability for its use. The same thing
can be said for any person or company
involved in the creation and production of
this manual.

• The device must be installed only and exclusively
by qualied technical personnel.

• Before any technical work on the appliance,
disconnect the power supply.

• Do not use power supply cables that seem worn
or old.

• Never, under any circumstances, make any
changes or connections that are not shown in
this handbook: improper use of the appliance
can cause serious hazards, risking the safety of
personnel and of the installation.

• Use only original spare parts. Non-original spare
parts could cause re, electrical discharge or other
hazards.

• Before proceeding with installation check the
supplied material to make sure it corresponds
to the order specication by examining the
identication labels (4.2 Product markings, page 2).

• When installing the device, comply with all the
national standards.

1

4 Identification

4.1 Product description and type designation

Power supply and control in weatherproof box
(IN 230Vac - OUT 24Vac) for ULISSE with infrared
illuminators. Night switch included.

4.2 Product markings

See the label attached to the outside of the package.

5 Preparing the product for

EN - English - Instructions manual

use

Any change that is not expressly approved
by the manufacturer will invalidate the
guarantee.

5.1 Safety precautions before use

In the 115/230Vac powered conguration
it is necessary to insert a 1 0 unipolar main
switch (open contact distance d>3mm).
This switch should be used to disconnect
the power supply before carrying out any
maintenance operation or before opening
the procuct.

5.2 Unpacking and contents

5.2.1 Unpacking

When the product is delivered, make sure that the
package is intact and that there are no signs that it
has been dropped or scratched.

If there are obvious signs of damage, contact the
supplier immediately.

Keep the packaging in case you need to send the
product for repairs.

5.2.2 Contents

Check the contents to make sure they correspond
with the list of materials as below:

• Power supply kit

• Instructions manual

5.3 Safely disposing of packaging

material

The packaging material can all be recycled. The
installer technician will be responsible for separating
the material for disposal, and in any case for
compliance with the legislation in force where the
device is to be used.

When returning a faulty product we recommend
using the original packaging for shipping.

2

6 Assembling and installing

Before starting any operation, make sure
the power supply is disconnected.

The assembly and installation must be
performed only by skilled personnel.

6.1 Installation

Electrical connections must be performed
with the power supply disconnected and
the circuit-breaker open.

6.1.1 Connection of the board

Open the watertight box, taking care not to damage
the seals. Pass the power and control cables through
the appropriate cable glands.

Fig. 1

Locate the position of the trimmer, input and output
power supply terminals and Day/Night contacts on
the control board.

P1 - Sensitivity adjustment

trimmer

J1 - IN 230 Vac J4 - OUT 24Vac J5 - Day/Night

status

Fig. 2

6.1.2 Connecting the dusk switch for the

IR illuminator

Connect the Day/Night (J5) output identied by
STATUS (+) to the alarm input (refer to the P&T
manual).

Connect the second Day/Night (J5) output identied
by STATUS to the alarms common terminal of the P&T.

6.1.3 Connection of the pan & tilt power

supply line

Connect the 24Vac power supply output (J4) to the
power supply connector of the pan & tilt. Use cables
with section of 1.5mm² (AWG 16).

Connect the power supply cables as described in the
table below.

CONNECTION OF THE POWER SUPPLY LINE

Colour Terminals

Power supply 24Vac

Dened by the installer ~/24Vac
Dened by the installer ~/24Vac
Yellow/Green GND/Earth

Tab. 1

Instructions manual - English - EN

3

6.1.4 Connection of the power supply line

Earth cable should be about 10mm longer
than the other two, so that it will not be
disconnected accidentally if pulled.

Connect the J1 power supply terminal to the electric
mains using suitable section cable (min. 1.5mm²).

Close the box, taking care to position the seals
correctly, and lock the cable glands.

The system is ready to be powered.

EN - English - Instructions manual

7 Configuration

The product has already been set in the factory for
optimal operation under a range of conditions, but
it can be adapted to suit the conditions where it will
actually be used.

Use trimmer P1 to adjust the intervention threshold
of the dusk sensor.

By rotating the trimmer clockwise, the night mode
changeover is anticipated (at a greater luminous
value). By rotating the trimmer anti-clockwise,
the night mode changeover is delayed (at a lower
luminous value).

We recommend making the adjustments under the
actual conditions in which the spots will be used.

The switching on of the red LED on the board stands
for the activation of the night-time mode.

8 Maintaining and cleaning

8.1 Maintaining

Maintenance must be carried out by
personnel trained to operate on electrical
circuits.

8.1.1 Fuses replacement

Use fuses with the following features:
T2A H 250V (F1), F8A L 250V (F2).

9 Disposal of waste materials

This symbol mark and recycle system
are applied only to EU countries and not
applied to the countries in the other area of
the world.

Your product is designed and manufactured with
high quality materials and components which can be
recycled and reused.

This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed of
separately from your household waste.

Please dispose of this equipment at your local
Community waste collection or Recycling centre.

In the European Union there are separate collection
systems for used electrical and electronic products.

4

10 Troubleshooting

Ask for assistance from skilled personnel if:

• The unit is damaged after being dropped;

• There is noticeable deterioration in performance

of the unit.

• The unit does not work properly, even though
all the instructions in this handbook have been
followed.

PROBLEM

CAUSE Fuses blown.
SOLUTION Make sure the power supply data

PROBLEM

CAUSE Incorrect wiring or incorrect

SOLUTION Ensure that the board STATUS

There is no power.

plate values coincide with the values
for the installation. Check whether
the green LED inside the box comes
on. Make sure there are no current
overloads or short circuits. Change
the fuses.

The unit does not allow the

Day/Night changeover of the
P&T.

trimmer regulation

contacts and the alarm contacts are
connected. Reset the dusk sensor
sensitivity.

11 Technical data

11.1 General

Plastic box, colour RAL7035

11.2 Mechanical

Dimensions (WxHxL): 226x167x280mm (8.9x6.6x11in)
Unit weight: 5.1kg (11lb)

11.3 Electrical

IN 230Vac, 50/60Hz - OUT 24Vac, 8A
Consumption: 200W max (powering two spots on

maximum power)
Built-in dusk sensor for automatic ON/OFF operation
Day/Night (STATUS): clean contact NO
Input cables size: AWG 12-14
Dimensions of signal cables: AWG 20-26

11.4 Environment

Indoor/Outdoor
IP56
Operating temperature: -25°C / +60°C (-13°F / +140°F)

12 Technical drawings

The dimensions of the drawings are in
millimetres.

Instructions manual - English - EN

62

50 45

226

50

Fig. 3 UPTIRPS230.

200 167

254

280

5

Headquarters Italy Videotec S.p.A.

Via Friuli, 6 - I-36015 - Schio (VI) Italy
Tel. [phone] - Fax [phone]
Email: [e-mail]

www.videotec.com

MNVKUIRPS230_1239_EN

UPTIRPS230

Alimentatore esterno per ULISSE con fari infrarossi

1 Informazioni sul presente manuale

Prima di installare e utilizzare questa unità, leggere
attentamente questo manuale. Conservare questo
manuale a portata di mano come riferimento futuro.

1.1 Convenzioni tipograche

PERICOLO!
Pericolosità elevata.
Rischio di scosse elettriche. Prima di
eseguire qualsiasi operazione assicurarsi di
togliere tensione al prodotto, salvo diversa
indicazione.

ATTENZIONE!
Pericolosità media.
L'operazione è molto importante per il
corretto funzionamento del sistema. Si
prega di leggere attentamente la procedura
indicata e di eseguirla secondo le modalità
previste.

INFO
Descrizione delle caratteristiche del
sistema.
Si consiglia di leggere attentamente per
comprendere le fasi successive.

2 Note sul copyright e informazioni sui marchi commerciali

I nomi di prodotto o di aziende citati sono marchi
commerciali o marchi commerciali registrati
appartenenti alle rispettive società.

3 Norme di sicurezza

Il produttore declina ogni responsabilità
per eventuali danni derivanti da un
uso improprio delle apparecchiature
menzionate in questo manuale. Si
riserva inoltre il diritto di modicarne il
contenuto senza preavviso. Ogni cura è
stata posta nella raccolta e nella verica
della documentazione contenuta in questo
manuale, tuttavia il produttore non può
assumersi alcuna responsabilità derivante
dall'utilizzo della stessa. Lo stesso dicasi
per ogni persona o società coinvolta nella
creazione e nella produzione di questo
manuale.

• L'installazione e la manutenzione del dispositivo
deve essere eseguita solo da personale tecnico
qualicato.

• Prima di eettuare interventi tecnici
sull'apparecchio togliere l'alimentazione elettrica.

• Non utilizzare cavi di alimentazione con segni di
usura o invecchiamento.

• Non eettuare per nessun motivo alterazioni o
collegamenti non previsti in questo manuale:
l'uso di apparecchi non idonei può portare a
gravi pericoli per la sicurezza del personale e
dell'impianto.

• Utilizzare solo parti di ricambio originali. Pezzi di
ricambio non originali potrebbero causare incendi,
scariche elettriche o altri pericoli.

• Prima di procedere con l'installazione controllare
che il materiale fornito corrisponda alle speciche
richieste esaminando le etichette di marcatura (4.2
Marcatura del prodotto, pagina 2).

• Si devono rispettare le normative nazionali per
l'installazione del dispositivo.

Manuale di istruzioni - Italiano - IT

1