Videology M14 Board, 20E407, 20E417, 20E409, 21E409 Operation Manual
...
Operation Manual
BOX CONTENTS
1. Camera module
2. Connection cable
3. User manual
SAFEGUARDS & WARNINGS
Prior to installation and use of this
product, the following WARNINGS should
only be observed.
1. Installation and servicing should only
be done by Qualified Service and
Installation Personnel.
2. Installation shall be done in accordance
with all local and national electrical and
mechanical codes.
3. Use only installation methods and materials capable of supporting four (4) times
the maximum specified load.
11/26/08 INS-20E407 Rev E
Camera Functions
Connectors and Controls
Lens options vary, but are pre-backfocused
for normal operation. Varifocal lens options
are indicated in model numbers ending in:
VA (4 to 9mm varifocals)
VB (DC Auto Iris 4 to 9mm varifocals)
WA (2.6 to 5.6mm varifocals)
WB (DC Auto Iris 2.6 to 5.6mm varifocals)
Front
Back
Power Board Controls
An optional 24VAC power board is available.
Note: Line lock is included with this
camera
Camera Settings
Push to Set White balance
The Push to Set White balance (Pt set) may
be implemented by selecting the switch
settings.
Next, focus the camera on a white background under the lighting that is to provide
illumination for the camera scene.
Push the button labeled “Push Lock White
Balance”. The camera White Balance will be
locked and will not change if the scene
changes.
M14 Board Lens
CS Lens
NTSC
PAL
NTSC
PAL
20E407
20E417
20E409
21E409
21E407
21E417
20E419
20E419
Dip Switch 1
Note- “On” Indicates “HI” Position
Function
Off
On
1 FLICKERLESS
Off (Default)
On
2 BLC
Off
On (Default)
3 M IRIS
Electronic CCD
DC Auto Iris
4 AE REF
100 IRE (Default)
80 IRE
5 AGC MAX
20dB max (Default)
26dB max
6 AWB1
White Balance Control (see below)
7 AWB2
White Balance Control (see below)
8 AWB3
White Balance Control (see below)
Note: for DCAI 1, 3, 4 are set ON
White Balance Control
WB AUTO
MODE
Switch 6
AWB1
Switch 7
AWB2
Switch 8
AWB3
Auto Enabled
Off
On
Off
Pt Set Enabled
Off
On
On
WB Fixed Mode
Switch 7
AWB2
Switch 8
AWB3
Color Temp.
Indoor
Off
Off
Approx. 3200K
Fluorescent
On
Off
Lamp
Off
On
Approx. 4200K
Outdoor Fixed
On
On
Approx. 6300K
Dip Switch 2
Note- “On” Indicates “HI” Position
Function
Off
On
1 GAMMA
1.0 enabled
0.45 enabled
(Default)
2 AE / ME
ME - Mechanical
Exposure enabled
AE - Auto Exposure
enabled (Default)
Line Lock
DC Iris
Video GND 12VDC
Push Lock White Balance
Dip Switch 1
1 Flickerless
2 BLC
3 M Iris
4 AE Ref
5 AGC Max
6 AWB 1
7 AWB 2
8 AWB 3
Dip Switch 2
1 Gamma
2 AE/ME
ALC
Adjustment
Technical Specifications
Electrical
20E407
NTSC
21E407
PAL
20E417
NTSC
21E417
PAL
CCD Sensor
1/3” Sony Interline CCD
Active Pixels (HxV)
768x492
752x582
512x492
512x582
Horizontal
Resolution
>460 TVL
>330 TVL
Sensitivity
<0.5 lux
Signal to Noise
Ratio
>46dB
Gamma
Default 0.45/selectable settings
Gain
Automatic/fixed (specified gain),
selectable
Synchronization
Internal / line lock
Back Light
Compensation
Selectable on/off
White Balance
Automatic/fixed setting, selectable/
push to set
Shutter Speed
From /50 (/60 EIA) to <1/10,000 sec,
Fixed shutter speed
Iris
Electronic iris, DC iris
Video Output
1Vp-p baseband video (75 ohm),
Optional YC
Power Supply
12VDC +/- 10%
Power Consumption
1.5W
Environmental
Ambient Operating
Temp.
-10° C ~ 55° C (14° F ~ 131° F)
Ambient Operating
Humidity
90% non-condensing
Storage Temp.
-25° C ~ 70° C (-13° F ~ 158° F)
Storage Humidity
95% non-condensing
Mechanical
Dimensions
WxHxD
38mm x 38mm x 30mm double board
(1.49” x 1.49” x 1.18”)
2.9, 3.6, 4.3, 6.0, 8.0, 12.0
Available board
lenses
Varifocal lens 4-9mm, 2.6-5.6m m
VA
Fixed iris 4-9mm
VB
DC iris 4-9mm
WA
Varifocal fixed iris 2.6-5.6mm
When ordering,
add suffix to
model Number
WB
Varifocal DC iris 2.6-5.6mm
20E407/ 21E407
M12 Board Mount
20E417/ 21E417
M12 Board Mount
20E409/ 21E409
C/CS Mount
Lens mount
20E419/ 21E419
C/CS Mount
Interfaces
Board connector/ power & video out
Ground
Line lock
Accessories
Optional
24VAC power board
Note: Serial Interface or YC options are special requests
Loading...