Videology 20E20X, 21E20X Instruction Manual

06/13/2013 INS-20E20X Rev B

Information may change without notice.

This document provides technical information for the user.
Videology reserves the right to modify the information in
this document as necessary. The customer should make
sure that they have the most recent manual version.
Videology holds no responsibility for any errors that may
appear in this document.

General Description

The 2xE20x is a single color CCD board camera
(32mm x 32mm). It’s small and simple design
allows customers to cost effectively integrate
into various products or equipment like ATM
Machines, Kiosks, Domes, Surveillance
Cameras etc.

Features

• Resolution is 540TVL

• 0.1 Lux Sensitivity

• Small compact board size

• DC Auto Iris capability

• ALC adjustable

• Day/Night mode (optional)

• Variety of CS, M12, M14 lenses

available

Box Contents

1. Camera module

2. Connection cable

Warning

To reduce the risk of fire or electric shock, do
not expose this appliance to rain, water or wet
locations. The camera is not to be mounted
outdoors or in hot, humid or otherwise harsh
environment.

Precautions

• Read and follow these instructions carefully.

• Use a proper UL listed 12V power supply.

• Make sure that no flammable substances get

on the camera. It could cause fire, short­circuits or damages.

• Be careful when handling the unit.
To prevent damage, do not drop the camera
or subject it to strong shock or vibration.

• Install away from electric or mag netic fields.

• Install away from any heat sources.

• Use proper grounding when ha n d l ing any

electronic materials.

• Protect from humidity and dust.

• Be careful when installing close to the

ceiling, in a kitchen or boiler room, as the
temperature may rise to high levels.

J3 Connector Settings (back)

ALC Level Control (front)

The 20/21E20X series can operate an auto iris
lens without an external board.

For ALC adjustment on a 20/21E20X, adjust
the potentiometer at the front of the camera.

Power Board Controls

(Optional 24VAC Board)

In dome enclosures the camera may be
connected to a power board that provides
24VAC/12VDC capability.

Videology Imaging Solutions, Inc.®

Videology Imaging Solutions®, Europe B.V.

37M Lark Industrial Parkway
Greenville, Rho

de Island 02828

Tel: (401) 949

– 5332

Fax: (401) 949 – 5276

Neutronenlaa n 4

5405 NH

Uden, The Netherlands

Tel: +31 (0) 413-

256261

Fax: [phone]

Americas, Middle East, Far East &

Australia sales:

sales

@videologyinc.com

www.videologyinc.com

Europe & N. Eurasia sales

:

[e-mail]

www.videology.nl

Instruction Manual

High Resolution (540TVL)

1/3” CCD Color Board Camera

20E20X / 21E20X

IMAGING SOLUTIONS INC.

Original Equipment Manufacturer

1) Power IN (Red)

2) GND (Blue)

3) Video (Yellow)

J3

32mm

32mm

IMAGE

J1

06/13/2013 INS-20E20X Rev B

Specifications Troubleshooting

Before sending the camera out for repair,
check the items below. If the problem persists
after checking these items, contact your
service center directly.

NO IMAGE:

• Is camera plugged into a proper power
supply?

• Check for proper coax cable connection.

• If a DCAI lens is used make sure it’s

plugged in.

• Check all connections are secure.

• Check that monitor is plugged in and

properly adjusted.

UNCLEAR IMAGE:

• Is lens dirty?

Dirt or fingerprints on the lens or sensor
can adversely affect the image. Gently wipe
any dirt or fingerprints off using a soft cloth
or lens cleaning paper and lens cleaning
fluid (commercially available).

• Is the monitor adjusted correctly?

• Is the lens adjusted correctly?

• Is there sufficient light i ng?

Electrical

NTSC

PAL

Image Sensor

1/3” IL CCD

Picture Elements

768 x 492

752 x 585

Resolution

540 TVL

Sensitivity

0.1 Lux (30 IRE) f1.2, 3200°k

Signal To Noise Ratio

>48 dB (AGC off)

Gamma

0.45

Gain Control

AGC 36dB

Synchronization

Internal (crystal controlled)

Scan Mode

Interlaced

Backlight Comp

Default ON

White Balance

Default AWB

Contour (Edge)
Enhancement

Factory set

Iris Controls

Auto detect (Electronic or DC auto iris)

Video Output

Composite 1Vp-p CVBS @75 ohms

Power Supply

+12VDC (+/- 10%)

Power Consumption

< 2.0W

Optional Factory

Settings

Via Hardware

BLC, Mirror mode, AGC

Via Software

Day/Night, Fixed Shutter

These options require a minimum quantity order. Please

contact a Videology sale represen tative for more details.

Environmental

Operation Temp

0°C ~ 70°C (32° F ~ 158° F)

Storage Temp

-25°C ~ 70°C (-13° F ~ 158° F)

Operation Humidity

20% ~ 90% RH

Storage Humidity

Up to 98% RH

Lifetime MTBF

>150,000 hours

Warning: Avoid aiming the camera at the sun or other

extremely bright lights. The CCD image sensor may be

damaged if exposed to very bright objects.

Mechanical

Dimensions W x H

x D w/ pinhole

mount

32mm x 32mm x 18.14mm

(1.26” x 1.26” x 0.71”)

Weight

9.5g (0.021 lbs)

Lens Mount

Replace “X” in model number with desired
lens mount option:

Example:

Change 20E20X to
20E205 to select an

M-12 Board Mount

2 = M-12 Pinhole

5 = M-12 Board
6 = M-14 Board

8 = CS Mount

Accessories

Included

Cable (J3) 60C1026
3-pin molex unterminated

Optional

Power Board 60PB24V-02
24VAC board