Videobaluns HD1011 Installation Manual

INSTALLATION MANUAL

PACKAGE CONTENTS

HDMI CAT-5 Extender

HD1011

VIDEOBALUNS
UNLIMITED

™

The HDMI CAT-5 Extender HD1011 allows you to
place your HDTV display up to 200 feet away from
your HDTV source. All you need is two CAT-5
cables. The HD1011 provides a cost effective way of

getting the most from your HDTV equipment.

The HD1011 includes a transmitter, receiver and two
6 foot HDMI cables. The transmitter is connected to
the HDTV source, such as a DVD player, set top box
or computer using one HDMI cable. The receiver is
connected to the display using the other HDMI cable.
Between the receiver and transmitter, connect two
CAT-5 or better cables of the required length. The
receiver includes an equalization switch to optimize
the image quality.

• HDMI 1.3 compliant

• Extends the distance between an HDTV source and
display up to 200 feet at 1080i or 720p resolution.

• Extends the distance between an HDTV source and
display up to 150 feet at 1080p resolution.

• Includes two 6 foot HDMI cables

• HDCP compliant

• Minimize the cable skew by an adjustable equalization
switch with 8 levels

• Included with the unit: a transmitter, receiver, power
supply, and two HDMI 6 foot cables.

• Video Bandwidth: 2.25 Gbps (HDMI 1.3)

• Input TMDS signal: 1.2 volts (peak-to-peak)

• Input DDC signal: 5 volts (peak-to-peak)

• HDMI Connector: 19 pin type female connector

• Power Supply: 5V 1A (UL & CE Approved)

• RJ-45 Connector: 2 indication LEDs

• Dimensions: 2.75" x 2.60" x 1.0" (Lx W x H)

• Shipping Weight: 2.5 lbs.

INSTALLATION

1. Connect your HDTV source (such as a DVD player)
to the transmitter using the included HDMI cable.

2. Connect your HDTV display (such as a plasma or
LCD TV) to the receiver using the other HDMI cable.

3. Connect your CAT-5/5e/6 cables between the
transmitter and receiver.

4. Plug in the power supply to the receiver.

5. If a flickering or a blinking image is seen, try adjusting
the equalization switch.

NOTE

1. For transmitting non-HDCP compliant video/audio,
you can use only one CAT-5/5e/6 cable using the
jack labeled “TMDS”.

2. All the transmission distances are measured using
high quality CAT-5e.

3. If used in an environment in which Electro Magnetic
Interference exists (such as close to fluorescent
lighting), shielded CAT-5/5e/6 cables can be used to
reduce EMI problems, especially over long distances.

4. Because the quality of the CAT-5/5e/6 cable has a
major effect on performance, the actual transmission
distance is subject to the electrical characteristics
of your CAT-5/5e/6 cable. For resolution greater than
1080i or 1280x1024, a CAT-6 cable is recommended.

PANEL DESCRIPTION

Front View – Transmitter

HDMI IN: Connect to your HDMI source with
the included HDMI cable here.

Rear View – Transmitter

TMDS: Plug in a CAT5/5e/6 cable to the jack
labeled TMDS on the receiver.

DDC: Plug in a CAT5/5e/6 cable to the jack
labeled DDC on the receiver.

Front View - Receiver

HDMI OUT: Connect to your HDTV display using
the included HDMI connector.

Rotary switch: Adjust the equalization strength
to optimize the image.

Rear View - Receiver

TMDS: Plug in a CAT5/5e/6 cable to the jack
labeled TMDS on the receiver.

DDC: Plug in a CAT5/5e/6 cable to the jack
labeled DDC on the receiver.

5V DV: Connect to the 5V DC power supply.

For technical support, please contact:

[e-mail]

Tel: [phone]