VIDAR NDTPRO, AdvantagePRO Series, DosimetryPRO Advantage, DiagnosticPRO Advantage, CAD PRO Advantage Installation Manual
VIDAR NDTPRO
Industrial Film Digitizer
Installation Guide
For Use with Windows 7, 8, & 10
(Serial Numbers 370,000 to 379,999)
© Copyright November 2019 by VIDAR Systems Corporation. All rights reserved.
365 Herndon Parkway
Herndon, VA 20170 U.S.A.
Phone: 1-703-471-7070
Fax: 1-703-471-7665
Internet: www.vidar.com
Emergo Europe
Prinsessegracht 20
2514 AP, The Hague
The Netherlands
Sales: 1-800-471-7070 or
1-800-471-7226
Email: order@3dsystems.com
Technical Support:
1-800-471-7070 or 1-703-471-7070
E-mail: medtech@3dsystems.com
E-mail: EmergoEurope@ul.com
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 2
Caution: No operator-serviceable parts inside. Refer servicing to qualified personnel.
Achtung: Gehäuse nicht öffnen. Wartung uno reparatur nur durch eletrofachkräfte.
Attention: Aucune piece ne peut etre remplacee par l’utilisateur. Toute operation de
maintenance doit etre effectuee par une personne qualiee.
Atencion: Acceso interno solo autorizado a personal tecnico cualificado.
Attenzione: Non appire. Rivolgersi a personale qualificado.
Radio Frequency Emissions
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area can cause harmful interference, in which case the user will be required
to correct the interference at his or her own expense.
Product compliance testing was conducted using VIDAR shielded cables. Modifications
to the digitizer or the VIDAR shielded cables or the use of cables other than those
available from VIDAR could void the user’s authority to operate the equipment.
Acceptable shipping conditions
Temperature: –18° to +60°C (0° to +140°F)
Relative humidity: 20% to 85%, non-condensing
Atmospheric pressure: 500 to 106 hPa (+18,000 to –1,200ft)
Operating conditions
Temperature: 10°C to 30°C (60°F to 85°F)
Relative humidity: 20% to 85%, non-condensing
Atmospheric pressure: 696 to 1013hPa (10,000 to 0 ft)
Electrical supply
Voltage: 100 to 240 VAC
Current: 0.75 to 1.5 A
Frequency: 47 to 63 Hz
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 3
Safety and compliance information
MEDICAL –GENERAL MEDICAL EQUIPMENT AS TO ELECTRIC SHOCK, FIRE
AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH: CSA CAN/CSAC22.2 NO. 60601-1:14, IEC 60601-1:2005+A1:2012) Edition 3.1. ANSI/AAMI
ES60601-1: A1:2012, C1:2009/(R)2012 and A2:2010/(R)2012.
Accessory equipment connected to the analog and digital interfaces must be certified
5RA9
This product is rated for continuous use.
This product is in the Ordinary Equipment Class. It provides no protection against the ingress of water.
This product is not suitable for use in the presence of flammable anesthetic mixtures with air or with oxygen or
with nitrous oxide.
according to the respective IEC standards (i.e. IEC 60950 for data processing equipment
and IEC 60601-1 for medical equipment). Furthermore all configurations shall comply
with the system standard IEC 60601-1-1 or IEC 60601-1 Edition 3.1.
Everybody who connects additional equipment to the signal input part or signal output
part configures a medical system, and is therefore responsible that the system complies
with the requirements of IEC 60606-1-1 or IEC 60601-1 Edition 3.1. If in doubt, consult
the technical services department or your local representative.
Class I Medical Device; No Applied Parts. This product provides Class I medical device protection against
electrical shock.
WARNING: To avoid the risk of electric shock, this equipment must only be connected to a supply mains with
protective earth.
Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked
“HOSPITAL ONLY” or “HOSPITAL GRADE”.
WARNING: Do not modify this equipment without authorization of the manufacturer.
Do not position the product so that it is difficult to access the disconnect switch (power switch) on the back of the
unit.
Mains power may be removed from the product by turning off the power switch on the back of the unit.
Power cords used with this device in North America must be rated by Underwriters Laboratories for hospital use.
Power cords used with this device in Europe must meet the requirements of IEC 227 Designation 53 or IEC 245
Designation 53.
Correct and safe operation of the digitizer requires familiarity with information
that is not marked on the product. The following symbols indicate that the
operator should consult the manual for additional information:
This Class 1 LED device is safe under reasonably foreseeable conditions of
operation.
The LED illumination system consists of 16 Class 1 LEDs, a mirror system to
spread the light, and a diffuser to distribute the light approximately uniformly
across an area of 2.4 sq. in (15.5 sq. cm). Light from the LED illuminator may be
indirectly observed in the digitizer’s film entry and exit areas.
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 4
Table of Contents
Intended Use ............................................................................................................................. 6
Unpack ....................................................................................................................................... 7
1. Look for Damage ...................................................................................................... 7
2. Unpack the shipping carton ..................................................................................... 8
3. Unpack the Accessory Box ....................................................................................... 9
4. Unwrap .................................................................................................................... 10
5. Identify the Components ......................................................................................... 11
6. If Anything Is Missing... ........................................................................................... 12
7. Activate Your Product Warranty.............................................................................. 12
Setting Up ................................................................................................................................ 13
1. Identify Important Features .................................................................................... 14
2. Assemble the Digitizer ........................................................................................... 15
3. Connect the Power Cord ........................................................................................ 20
Device Driver Installation ....................................................................................................... 21
Install Device Drivers for Windows 7, 8, and 10 ........................................................... 21
1. Apply Power to the Digitizer .................................................................................... 21
2. About the VIDAR Drivers ........................................................................................ 22
3. Install the VIDAR Drivers ........................................................................................ 22
Appendix: Electromagnetic Guidance ................................................................................. 29
Appendix: Symbols ............................................................................................................... 33
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 5
Intended Use
The NDTPRO Industrial Film Digitizer is intended for making digital copies of x-ray films for nondestructive testing applications. This device is not intended for medical use.
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 6
In this chapter, you will:
Unpack and inspect the digitizer’s parts.
Identify the digitizer’s parts.
1. Look for Damage
Before unpacking the Digitizer, examine the shipping carton for damage.
If the carton is damaged:
Notify the shipper immediately.
Take photographs of the damage.
Send pictures and description of damage to: medtech@3dsystems.com.
Notify VIDAR Support at 1-703-471-7070.
Unpack
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 7
2. Unpack the shipping carton
IMPORTANT: Save all the packing materials. If you need to
ship the digitizer later, you should repack the digitizer in the
original materials by reversing the procedure described here.
Failure to properly pack, or failure to use VIDAR authorized
shipping materials, will void the product’s warranty, and will
likely result in costly repairs.
Remove items from the shipping carton in the order shown below.
1
Upper foam support
Leave in box:
lower foam support
2
Feeder
Note: For clarity, this
illustration does not show
the plastic bags surrounding
the digitizer and feeder.
3
Digitizer base
4
Accessory box
Shipping carton
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 8
IMPORTANT: Save all the packing materials. If you need to
ship the digitizer later, you should repack the digitizer in the
original materials by reversing the procedure described here.
Failure to properly pack, or failure to use VIDAR authorized
shipping materials, will void the product’s warranty, and will
likely result in costly repairs.
3. Unpack the Accessory Box
a. Remove these items from the accessory box:
2
Film support bar
in padded bag
(bag not shown)
3
Power cord
1
USB cable
4
Documentation in
padded bag (bag
not shown)
Accessory box
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 9
b. Then remove these items from the accessory box:
5
Cardboard retainer
4. Unwrap
6
Exit tray
7
Stand
Accessory box
Note: For clarity, this
illustration does not show
the plastic bag surrounding
the exit tray.
a. Unwrap all items.
b. Remove the foam block from the rear of the digitizer base:
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 10
IMPORTANT: Save the carton and all packing materials. If
you need to ship the digitizer later, you must repack it using the
original wire ties, plastic bags, foam supports and cartons.
Instructions for repacking are provided in the “Packing the film
digitizer for shipment” section of this manual.
5. Identify the Components
Item
Digitizer base
Exit tray
Film feeder
Film support bar
Stand
Power cord: 115V (p/n 4043-001) or 230V (p/n 2104-006)
Quick setup card
USB cable: 6 foot (p/n 4618)
VIDAR NDTPRO Industrial Film Digitizer CD
Digitizer Base
Film Support bar
Exit Tray
Stand
Film Feeder
19440-001 Rev. E VIDAR NDTPRO Industrial Film Digitizer Installation Guide 11
Loading...