Victory Motorcycles OCTANE 2017 Rider's Manual
2017 Rider’s Manual
OCTANE™
California Proposition 65 Warning
This product contains or emits
chemicals known to the state of
California to cause cancer and birth
defects or other reproductive harm.
1
2017 Rider’s Manual
OCTANE™
2
Copyright 2015 Polaris Industries Inc.
All material in this publication is based on the latest product information at the time of publication. Due to
constant improvements in the design and quality of production components, some minor discrepancies may result
between the actual vehicle and the information presented in this publication. Depictions and/or procedures in this
publication are intended for reference use only.
No liability can be accepted for omissions or inaccuracies. VICTORY MOTORCYLES reserves the right to make
changes at any time, without notice and without incurring obligation to make the same or similar changes to
previously manufactured vehicles. Any reprinting, reuse or redistribution of the material in this document is
expressly prohibited.
VICTOR Y®, VICT ORY MOTORCYCLES®, POLARIS® and OCTANE™ are trademarks of Polaris Industries
Inc.
Printed in U.S.A.
P/N 9926391
3
WARNING
Improper vehicle use can result in SEVERE INJURY or DEATH.
NEVER Operate:
• If you are under the age of 16 and without a driver’s license with motorcycle endorsement
• Under the influence of drugs or alcohol
• Off-road
• With more than one passenger (motorcycle must be equipped with passenger foot pegs)
• With weight that exceeds maximum weight rating
ALWAYS:
• Wear a helmet, eye protection, gloves, long-sleeve shirt, long pants and over-the-ankle boots.
• Make sure any passenger reads and understands all safety labels.
• Be aware of your surroundings and driving conditions.
• Keep both hands on the handlebars and both feet on the footrests when riding.
• Use only genuine VICTORY accessories designed for your model.
READ RIDER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND WARNINGS.
Safety Training
Safety training is a top priority for POLARIS. POLARIS strongly encourages you to take a rider
education course from the Motorcycle Safety Foundation or another qualified instructor. The course
will help you develop or refresh your expertise in safe riding habits through instruction and riding.
For information on Motorcycle Safety Foundation rider edu cation courses in your area, call 1-800446-9227 or visit their home page at www.msf-usa.org.
ALWAYS USE AN
APPROVED HELMET
AND PROTECTIVE
GEAR.
NEVER USE WITH
DRUGS OR ALCOHOL.
4
5
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Reporting Safety Defects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Instruments, Features and Controls. . . . . . . . . . . . . . . . . . . . . . 25
Pre-Ride Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cleaning and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Identification Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Maintenance Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
6
Introduction
Thank you for purchasing a Polaris vehicle, and welcome to our world-wide family of
Polaris owners. We proudly produce an exciting line of utility and recreational products.
For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and
recommendations in this rider’s manual. Keep this manual with the motorcycle, especially
when ownership changes. If your rider’s manual is misplaced or damaged, please purchase a
replacement from your VICTORY dealer.
All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operator’s
perspective when seated in a normal riding position. If you have questions about the
operation or maintenance of your motorcycle after you've read this manual, your authorized
VICTORY dealer can assist. To locate the nearest authorized VICTORY dealer, call 1-877737-7172 or visit www.victorymotorcycles.com.
VICTORY motorcycles comply with all federal, state and local safety and emission
regulations for the area of intended sale.
• Snowmobiles • RZR® sport vehicles
• All-terrain vehicles (ATVs) • GEM® electric vehicles
• Low emission vehicles (LEVs) • VICTORY® motorcycles
• RANGER® utility vehicles • INDIAN® motorcycles
•BRUTUS® work vehicles • POLARIS POWER® generators
• SLINGSHOT® three wheel motorcycles • POLARIS DEFENSE® combat vehicles
7
Safety
About the Rider's Manual
Failure to follow recommended precautions and procedures could result in severe injury or death.
Always heed all safety precautions and follow all operation, inspection and maintenance procedures
outlined in this manual.
This rider’s manual contains information that is essential to safe riding and proper
maintenance of your VICTORY motorcycle. Anyone who uses the motorcycle (operators
and passengers) must read the rider’s manual before riding. Carefully read and understand
the information found in the Safety section. Understand and follow the procedures outlined
in the Maintenance section to keep your VICTORY motorcycle in top condition on the road
or in storage. Bring the manual with you when you ride. Following the precautions and
procedures in the manual will add to your enjoyment and help keep you riding safely. If you
lose or damage this manual, you can purchase a new one through any authorized VICTORY
dealer. The rider’s manual should be considered part of the motorcycle and remain with it if
sold.
WARNING
8
Safety
Safety Terms and Signal Words
The following signal words and symbols appear throughout this manual and on your vehicle.
Your safety and the safety of others is involved when these words and symbols are used.
Become familiar with their meanings before reading the manual.
The safety alert symbol indicates a potential personal injury haza rd.
DANGER
A DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING
A WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION
A CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate
injury.
NOTICE
A NOTICE indicates a situation that could result in property damage.
The Prohibition Safety Sign indicates an action NOT to take in order to avoid a hazard.
The Mandatory Action Sign indicates an action that NEEDS to be taken to avoid a hazard.
9
Safety
Safe Riding Practices
Improper use of this motorcycle can result in serious injury or death to you, your passenger and others.
To minimize the risk of injury, read and understand the information contained in this section before
operating the motorcycle. This section contains safety information specific to the VICTOR Y motorcycle,
as well as information about general motorcycle safety. Anyone who rides the motorcycle (operators
and passengers) must follow these safety precautions.
Motorcycling has inherent risks.
You can minimize those risks, but you can't eliminate them completely. Even if you're an
experienced motorcycle operator or passenger, read all of the safety information in this
manual before operating the motorcycle.
• Take a rider education course from the Motorcycle Safety Foundation or another qualified
instructor. The course will help you develop or refresh your expertise in safe riding habits
through instruction and riding. For information on Motorcycle Safety Foundation rider
education courses in your area, call 1-800-446-9227 or visit their web site at www.msfusa.org.
• Read and understand all information in this rider’s manual.
• Observe all maintenance requirements specified in this manual. For more information, see
the VICTORY Service Manual. Your authorized VICTORY dealer can assist.
Design characteristics affect how you should ride the VICTORY motorcycle.
• The motorcycle is designed for on-road use with one rider and one passenger. See the
manufacturer’s label (on the left side of the frame at the steering head). The label contains
the Vehicle Identification Number (VIN) and Gross Vehicle Weight Rating (GVWR) and
Gross Axle Weight Rating (GAWR) information. Never exceed the GVWR or the GAWR.
• Riding off-road, riding with more than one passenger, or carrying weight exceeding the
maximum weight rating can make handling difficult, which could cause loss of control.
• During the first 500 miles (800 km) of operation, follow all break-in procedures as
outlined in the break-in section beginning on page 44. Failure to do so can result in serious
engine damage.
• Some VICTORY motorcycles include saddlebags, a windshield, a trunk, luggage racks or
a passenger backrest as standard equipment. To maintain stability, be prepared to reduce
the operating speed of motorcycles equipped with these items.
WARNING
10
Safety
Safe Riding Practices
Follow these general safe riding practices:
• Before each ride, perform the pre-ride inspections as outlined beginning on page 36.
• Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding
where there is little or no traffic. Practice riding at a moderate speed on various road
surfaces and in different weather conditions.
• Know your skills and limits, and ride within them.
• Allow only licensed, experienced operators to ride your motorcycle, and then only after
they have become familiar with its controls and operation. Make sure all riders read and
understand this rider’s manual before riding.
• Do not ride when you're fatigued, ill or under the influence of alcohol, prescription drugs,
over-the-counter drugs or any other drugs. Fatigue, illness, alcohol and drugs can cause
drowsiness, loss of coordination and loss of balance. They can also affect your awareness
and judgment.
• If your motorcycle operates abnormally, correct the problem immediately. For more
information, see the VICTORY Service Manual. Your authorized VICTORY dealer can
assist.
• Ride defensively, as if you are invisible to other motorists, even in broad daylight. A
motorist's failure to see or recognize a motorcycle is the leading cause of automobile/
motorcycle acci dents. Ride where you're clearly visible to other motorists, and observe
their behavior carefully.
• Be especially cautious at intersections, as these are the most likely places for an accident.
• To prevent loss of control, keep your hands on the handlebars and your feet on the
footrests.
• Be aware that the highway bar is not designed to protect the rider from injury in a
collision.
• Do not move or operate the motorcycle with the steering locked (if equipped), as the
severely restricted steering could result in loss of control.
• Obey the speed limit and adjust your speed and riding technique based on road, weather
and traffic conditions. As you travel faster, the influence of all other conditions increases,
which can affect the motorcycle's stability and increase the possibility of losing control.
11
Safety
Safe Riding Practices
• Reduce speed when:
• the road has potholes, or is otherwise rough or uneven.
• the road contains sand, dirt, gravel or other loose substances.
• the road is wet, icy or oily.
• the road contains painted surfaces, manhole covers, metal grating, railway crossings or other
slippery surfaces.
• The weather is windy, rainy or otherwise causing slippery or rapidly changing conditions.
• Traffic is heavy, congested, not allowing sufficient space between vehicles or otherwise not
flowing smoothly.
• You are being passed in either direction by a large vehicle that may produce a wind blast in its
wake.
• T o maximize braking ef fectiveness, use the fr ont and rear brakes together. Be aware of the
following braking facts and practices:
• The rear brake provides 40% of the motorcycle's stopping power, at most. Use the front and rear
brakes together.
• To avoid skidding, apply the brakes gradually when the road is wet or rough, or contains loose or
other slippery substances.
• If possible, avoid applying the brakes while making a turn. Motorcycle tires have less traction
during turns, so braking will increase the possibility of skidding. Bring the motorcycle to the
upright position before applying the brakes.
• When approaching a curve, choose a speed and lean angle that allows you to pass through
the curve in your own lane without applying the brakes. Excessive speed, improper lean
angle or braking in a curve can cause loss of control.
• Ground clearance is reduced when the motorcycle leans. Do not allow components to
contact the road surface when leaning the motorcycle in a curve, as this could cause loss of
control.
• Retract the sidestand fully before riding. If the sidestand is not fully retracted, it could
contact the road surface and cause loss of control.
• Do not tow a trailer. Towing a trailer can make the motorcycle hard to handle.
Anti-Lock Brake System Response (if equipped)
• When the anti-lock brakes engage during a braking event, the rider will feel pulsing at the
brake levers. Continue to apply steady pressure to the brakes for the best stopping
performance.
12
Safety
Safe Riding Practices
Carrying a Passenger
Do not carry a passenger unless the motorcycle is equipped with passenger seat and
passenger footrests.
To carry a passenger safely:
• Do not exceed the gross vehicle weight rating (GVWR). See the manufacturer’s label (on
the left side of the frame at the steering head).
• If necessary, adjust the rear shock preload. See page 70. Improper preload adjustment can
make your motorcycle hard to handle and can cause loss of control.
• Before riding, be sure your passenger is familiar with safe riding procedures. An
inexperienced passenger may distract you or make movements that cause instability.
• Direct the passenger to hold onto you or the seat strap with both hands and to keep both
feet on the passenger footrests. Do not carry a passenger who cannot place both feet firmly
on the passenger footrests. A passenger who rides improperly can shift body weight
erratically and cause instability.
• Adjust your riding style to compensate for the differences in handling, acceleration and
braking caused by the additional weight of the passenger.
13
Safety
Safe Riding Practices
Protective Apparel
Wear protective apparel to decrease the risk of injury and increase riding comfort.
• Always wear a helmet that meets or exceeds established safety standards. Approved
helmets in the USA and Canada bear a U.S. Department of Transportation (DOT) label.
Laws in some areas require that you wear an approved helmet. Head injuries are the
leading cause of fatalities in accidents involving motorcycles. Statistics prove that an
approved helmet is the most effective protection in preventing or reducing head injuries.
• Wear eye protection to protect eyes from wind or airborne particles and objects. Laws in
some areas require that you wear eye protection. VICTORY recommends that you wear
approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8,
Z87.1, or CE. Make sure protective eyewear is kept clean.
• All riders should wear bright or light-colored and/or reflective clothing to improve
visibility to other motorists. A motorist's failure to see or recognize a motorcycle is the
leading cause of automobile/motorcycle accidents.
• Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from
abrasions, lacerations or burns should the motorcycle fall. Wear boots with low heels, as
high heels can catch on pedals or footrests. The combination of boots and pants should
completely cover legs, ankles and feet, protecting skin from engine and exhaust system
heat.
• Do not wear loose, flowing clothing or long boot laces, as they can catch on handlebars,
levers or footrests, or they can become entangled in the wheels, causing loss of control and
serious injury.
14
Safety
Gross Vehicle Weight Rating (GVWR)
WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and
handling and could cause loss of control. NEVER exceed the GVWR of your motorcycle.
The maximum load capacity of your motorcycle is the maximum weight you may add to
your motorcycle without exceeding the GVWR. This capacity is determined by calculating
the difference between your motorcycle’s GVWR and wet weight.
Refer to the specification section beginning on page 102 or the Manufacturing Information/
VIN label on the motorcycle frame for model-specific information. See page 21.
When determining the weight you will be adding to your motorcycle, and to ensure you do
not exceed the maximum load capacity, include the following:
• operator body weight
• passenger body weight
• weight of all riders’ apparel and items in or on apparel
• weight of any accessories and their contents
• weight of any additional cargo on the motorcycle
Carrying Cargo
Use the following guidelines when attaching cargo or accessories to the motorcycle. Where
applicable, these guidelines also refer to the contents of any accessories.
• Keep cargo and accessory weight to a minimum, and keep items as close to the motorcycle
as possible to minimize a change in the motorcycle’s center of gravity. Changing the
center of gravity can cause loss of stability and handling and could cause loss of control.
• Distribute weight evenly on both sides of the motorcycle. Maintain even weight
distribution by checking accessories and cargo to make sure they’re securely attached to
the motorcycle before riding and whenever you take a break from riding. Uneven weight
distribution, or accessories or cargo that shift suddenly while you’re riding can make the
motorcycle hard to handle, can cause loss of control, or cargo could fall from the
motorcycle creating a hazard for surrounding vehicles.
• Do not attach large or heavy cargo such as sleeping bags, duffel bags or tents to the
handlebars, front fork area or front fender. Cargo or accessories placed in these areas can
cause instability (due to improper weight distribution or aerodynamic changes) and could
cause loss of control. Such items can also block air flow to the engine and cause
overheating that can damage the engine.
• Do not exceed the maximum cargo weight limit of any accessory (see accessory
instructions and labels). Do not attach cargo to an accessory not designed for that purpose.
Either circumstance could result in an accessory failure that could cause loss of control.
• Do not attach anything to the motorcycle unless specifically designed for that purpose by
VICTORY.
15
Safety
Carrying Cargo
Saddlebags
When operating a motorcycle equipped with saddlebags:
• Never ride at speeds exceeding 80 MPH (120 km/h). Depending on load and weather
conditions, the maximum safe operating speed may be less. Saddlebags, combined with
the lifting or buffeting effects of wind, can cause instability.
• Distribute weight evenly in each of the saddlebags.
• Do not exceed the maximum cargo capacity of the saddlebags.
• Do not exceed the gross vehicle weight rating (GVWR).
Parking the Motorcycle
When leaving the motorcycle unattended, turn the engine off. Remove the ignition key to
prevent unauthorized use by minors or those without proper motorcycle certification and
training.
Park the motorcycle where people are not likely to touch the hot engine or exhaust system or
place combustible materials near these hot areas. Do not park near a flammable source such
as a kerosene heater or an open flame, where hot components could ignite combustible
materials.
Park the motorcycle on a firm, level surface. Sloped or soft surfaces may not support the
motorcycle. If you must park on a slope or soft surface, follow the precautions outlined on
page 51.
Modifications
Modifying the motorcycle by removing any equipment or by adding equipment not approved
by VICTORY may void your warranty. Such modifications could make the motorcycle
unsafe to ride and could result in severe injury to operator or passengers, as well as damage
to the motorcycle. Some modifications may not be legal in your area of operation. If in
doubt, your authorized VICTORY dealer can assist.
16
Safety
Transporting the Motorcycle
When transporting the motorcycle:
• Use a truck or trailer. Never tow the motorcycle. Towing will impair steering and
handling.
• Restrain the motorcycle in an upright position to prevent fuel leaks.
• Place the transmission in neutral.
• Do not place restraints on the handlebars. Carefully route the tiedown straps between the
fairing and the fork tubes. Position the tiedown straps around the fork tubes above the
lower triple clamp, being sure to not pinch brake lines or wire harnesses. Secure the rear of
the motorcycle with tiedowns around both sides of the rear axle, being careful to avoid the
brake line, exhaust and drive belt.
Restrain with 2 straps
on each side.
17
Safety
Use of Accessories
Because VICTORY cannot test and make specific recommendations concerning every
accessory or combination of accessories sold, the operator is responsible for determining that
the motorcycle can be safely operated with any accessories or additional weight. Use the
following guidelines when choosing and installing accessories:
• Do not install accessories that impair the stability, handling or operation of the motorcycle
or operator visibility. Before installing an accessory, be sure that it does not:
• Reduce ground clearance when the motorcycle is either leaned or in a vertical position.
• Limit suspension or steering travel or your ability to operate controls.
• Displace you from your normal riding position.
• Obscure lights or reflectors.
• Bulky or large accessories can cause instability (due to the lifting or buffeting effects of
wind) and loss of control.
• Do not install electrical accessories that exceed the capacity of the motorcycle’s electrical
system. Never install higher wattage light bulbs than those supplied as original equipment.
An electrical failure could result and cause hazardous loss of engine power or lights, or
damage to the electrical system.
• Use only genuine VICTORY accessories designed for your model.
18
Safety
Fuel and Exhaust Safety
Gasoline is highly flammable and explosive under certain conditions.
• Always exercise extreme caution whenever handling gasoline.
• Always turn off the engine before refueling.
• Always refuel outdoors or in a well-ventilated area.
• Open the fuel cap slowly. Do not overfill the tank. Do not fill the tank neck.
• Do not smoke or allow open flames or sparks in or near the area where refueling is performed or
where gasoline is stored.
Gasoline and gasoline vapors are poisonous and can cause severe injury.
• Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you swallow gasoline, inhale
more than a few breaths of gasoline vapor, or get gasoline in your eyes, see a physician
immediately.
• If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change
clothing.
• If gasoline spills on the any part of the motorcycle, immediately rinse it off with water.
Exhaust gases contain carbon monoxide, a colorless, odorless gas that can cause loss of
consciousness or death in a short time.
• Never start the engine or let it run in an enclosed area.
• Never inhale exhaust gases.
WARNING
19
Safety
Safety Maintenance
Failure to perform safety maintenance as recommended can result in difficult handling and loss of
control, which could result in serious injury or death. Always perform the safety maintenance
procedures as recommended in this manual. Perform safety-related maintenance and repairs promptly
as outlined in the VICTORY Service Manual, or see your authorized VICTORY dealer for service.
• Before each ride, perform the pre-ride inspections. See page 36.
• Perform maintenance at the intervals specified in the periodic maintenance table. See page
54.
• Always maintain proper tire pressure, tread condition and wheel and tire balance. Inspect
tires regularly and replace worn or damaged tires promptly. Use only approved
replacement tires. For more information, see the VICTORY Service Manual. Your
authorized VICTORY dealer can assist.
• Always ensure proper steering head bearing adjustment.
• Regularly inspect the rear shock absorber and the front forks for fluid leaks or damage.
Make any necessary repairs promptly.
• Clean the motorcycle thoroughly to reveal items in need of repair.
• Fasteners must meet original specifications for quality, finish and type to ensure safety.
Use only genuine VICTORY replacement parts, and ensure that all fasteners are tightened
to the proper torque.
WARNING
20
Safety
Electromagnetic Interference
This vehicle complies with the requirements of European regulation 44/2014/RVCR/Annex
VII, United Nations ECE regulation 10 and Canadian ICES-002.
Reporting Safety Defects
If you believe that your vehicle has a defect that could result in a crash or cause injury or
death, you should immediately inform the National Highway Traffic Safety Administration
(NHTSA) in addition to notifying Polaris Industries in writing.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a
safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
However, NHTSA cannot become involved in individual problems between you, your dealer
or Polaris Industries.
T o contact NHTSA, or obtain other information about motor vehicle safety, you may call the
Vehicle Safety Hotline toll free at 1-888-327-4236 (TTY : 1-800-424-9153), visit the NHTSA
web site at www.safercar.gov, or write to:
ADMINISTRATOR, NHTSA
1200 New Jersey Avenue, SE
West Building
Washington, DC 20590
21
Safety
Safety and Information Labels
Labels are model-specific and market-specific. Your motorcycle may not contain all of the
labels shown.
1. Vehicle Identification Number (VIN) Stamped on Frame
2. Vehicle Identification Number (VIN) on Manufacturing Label
3. Vehicle Emission Control Information (VECI) Label
4. Noise Emission Control Information (NECI) Label
5. Evaporative Emissions Control Label
6. Operator Warning/Fuel Recommendation Label
2
3, 4, 5
6
1
22
Component Identification
7
6
10
9
13
12
4
1
3
8
2
11
21
20
14
10
16
8
15
19
4
17
22
1. Driver’s Seat
2. Air Box (under fuel tank)
3. Fuel Tank
4. Mirror
5. Fairing
6. Right Front Turn Signal
7. Headlight
8. Front Fork
9. Rear Brake Pedal
10. Driver’s Footrest
11. Mufflers
12. Right Rear Turn Signal
13. Taillight
14. Left Front Turn Signal
15. Ignition Switch
16. Battery (under seat)
17. Left Rear Turn Signal
18. Multi-Tool (behind license plate
bracket)
19. Coolant Recovery Bottle
20. Sidestand
21. Gear Shifter
22. Radiator
5
18
23
Component Identification
Handlebar/Console Components
Engine Identification Number
The engine number is stamped into the bottom
of the left crankcase near the sidestand. The
first 8 digits are the engine model number. The
last 5 digits are the serial number.
Record the number in the space provided on
page 104.
Ignition Key Number
The key identification number is stamped on
the metal key tag attached to the key ring. If it
becomes necessary to replace the ignition key
for any reason, provide the key number to your
VICTORY dealer.
Record the number in the space provided on
page 104.
3
1
4
6
7
2
5
1. Clutch Lever
2. Mirror
3. Instrument Cluster
4. Fuel Cap
5. Front Brake Fluid Reservoir
6. Front Brake Lever
7. Throttle Control Grip
Engine Identification
Number
Key Number
24
Component Identification
Switches
Symbol Switch Description
Hazard Warning
Flashers Switch
The hazard warning flashers switch activates and cancels the hazard
warning flashers. See page 26.
High/Low Headlight
Beam Switch
The high/low headlight beam switch toggles the headlight between
high beam and low beam. See page 25.
Horn Switch To sound the horn, press the horn switch.
Turn Signal Switch Move the switch to the left to activate the left turn signals. Move the
switch to the right to activate the right turn signals. A signal will
deactivate automatically when speed or distance reach
predetermined levels. T o cancel a signal manually , move the switch to
the center position and push it inward. Momentary Feature: Move the
turn signal switch left or right and hold it in that position for at least
one second. The momentary feature will activate and the signal will
then cancel when the switch is released.
If a bulb fails, the lamp flashes at more than twice the normal rate.
Stop/Run Switch Press the bottom of the switch (RUN) to allow the engine to start and
run. Press the top of the switch (STOP) to stop the engine. See page
25.
Starter Switch Use the starter switch to start the engine. The engine stop/run switch
must be in the RUN position. See page 25.
Left Control Right Control
High/Low Light
Switch
Horn Switch
Engine Starter Switch
Engine Stop/Run
Switch
Mode Button
Turn Signal Switch
Hazard Warning
Flashers Switch
25
Component Identification
Switches
Engine Stop/Run Switch
Use the engine stop/run switch to turn the engine off quickly. Turn the key off after the
engine stops.
• Press the top of the switch (STOP) to interrupt the
circuits and stop the engine. The engine should
not start or run when the switch is in the STOP
position.
• Press the bottom of the switch (RUN) to complete
the circuits and allow the engine to start and run.
Tip: The headlights and any accessories plugged into
power ports will remain on until the ignition key is
turned off.
Starter Switch
Read the engine starting procedures before starting
the engine. See page 47. The engine stop/run switch
must be in the RUN position and the transmission
must be in neutral, or the clutch must be disengaged.
Press and release the starter switch to start the engine.
High Beam/Low Beam Light Switch
Press the upper portion of the switch to activate the
high beam. Press the lower portion of the switch to
activate the low beam.
Horn Switch
To sound the horn, press the horn switch.
Engine Stop/Run
Switch
Engine Starter
Switch
High/Low Beam
Switch
Horn Switch
26
Component Identification
Switches
Turn Signal Switch
Move the turn signal switch to the left to activate the
left turn signals. Move the switch to the right to
activate the right turn signals. A signal ends when
speed or distance reach preset levels. To end a
signal manually, move the switch to the center and
push it inward.
Momentary Feature: Move the turn signal switch
left or right and hold it in that position. The signal
flashes until the switch is released.
Hazard Warning Flashers Switch
The ignition switch must be in the ON position to
activate the hazard warning flashers, but once
activated, the hazard warning flashers will continue
to flash when the ignition switch is turned off.
When the hazard warning flashers are active, all four turn signals flash.
• Press and hold the hazard warning flashers switch for 1-2 seconds to activate the hazard
warning flashers.
• Press and release the switch to cancel the hazard warning flashers.
Mode Button
The mode button is located on the front side of the
left handlebar controls. With the ignition switch on,
use the mode button to toggle through the modes of
the multi-function display. Use the mode button to
set the display units to either standard or metric
units of measurement. See page 30.
Turn Signal Switch
Hazard Warning Flashers Switch
Mode Button
27
Component Identification
Switches
Ignition/Light Key Switch
The ignition/light key switch controls the electrical
functions of the motorcycle. The switch is located on
the ignition cover on the left side of the motorcycle.
Motorcycle riders must remain as visible as possible at
all times. To aid in this, the headlight must be on at all
times while operating. The headlights automatically
operate when the engine is running. Do not modify the
ignition/light switch wiring to circumvent the automatic
headlight feature.
Before starting the engine, read the instructions for
starting the engine. See page 47.
Turn the ignition switch to the OFF position and
remove the ignition key when leaving the motorcycle
unattended.
OFF
All electrical circuits are inactive and the ignition key
can be removed.
ON
All electrical circuits are energized and the ignition key
cannot be removed. The headlamp, taillight and
instrument lights illuminate.
PARK (P)
Push the key into the ignition switch while turning it to
the PARK position. In PARK, the taillight, indicator
lights and license plate light illuminate. Vehicle
powered accessories (if equipped) can be operated and
the instrumentation is active. The emergency flashers
can be activated. The ignition key can be removed.
OFF
ON
PARK
Ignition Switch
28
Instruments, Features and Controls
Instrument Cluster
Speedometer
The speedometer displays forward vehicle speed in either miles per hour or kilometers per
hour.
Indicator Lamps
Lamp Indicates Condition
High Beam This lamp illuminates when the headlamp switch is set to high beam.
Chassis Fault The alert symbol illuminates if a chassis fault occurs.
Turn Signals The corresponding turn signal indicator flashes when the left, right or
both turn signals (hazard warning flashers) are active. If there is a
problem in the signal system, the lamps will flash at twice the normal
rate.
Anti-Lock Brake
System Not Activated
(if equipped)
The ABS indicator always illuminates when the key is in the ON
position and remains on until the anti-lock system activates, which
occurs when vehicle speed exceeds 6 MPH (10 km/h). When the
lamp is illuminated, the anti-lock brakes will not activate, but the
conventional brake system will continue to operate normally .
Neutral This lamp illuminates when the transmission is in neutral and the
ignition key is in the ON position.
Low Fuel This lamp illuminates when about 1/2 gallon (1.9 L) of fuel remains in
the tank.
Check Engine If this lamp illuminates while the engine is running, prompt service is
required. The light will remain on if the tilt sensor shuts down the
engine. If abnormal sensor or engine operation is detected the light
will remain on as long as the fault condition exists. Retrieve the error
codes for diagnosis. See page 31.
Not used
Speedometer
Indicator Lamps
Multi-Function
Display
Loading...