Victory Vision Tour 2015 Owner's manual

2015 Rider’s Manual

Victory Vision Tour

California Proposition 65 Warning

This product contains or emits

chemicals known to the state of

California to cause cancer and birth

defects or other reproductive harm.

2015 Rider ’s Manual

Victory Vision® Tour

of publication. Product improvements or other changes may result in differences between this manual and the motorcycle. Depictions and/or procedures in this publication are intended for reference use only.

No liability can be accepted for omissions or inaccuracies. Polaris Industries reserves the right to make changes at any time, without notice and without incurring obligation to make the same or similar changes to motorcycles previously built. Any reprinting or reuse of the depictions and/or procedures contained within, whether whole or in part, is expressly prohibited.

All reference to RIGHT, LEFT, FRONT, REAR are from the operator’s perspective seated in a normal riding position.

Features of VICTORY Motorcycles are covered by U.S. Patent Nos: 6,976,691; 6,407,663; D489670; D482311; D482304; D481980; D481973; D474142.

The following are registered trademarks of Polaris Industries Inc.: POLARIS DUNLOP® is a registered trademark of Dunlop Tire Corporation.

LOCTITE® is a registered trademark of Henkel Corporation. Sirius® and XM® and all related marks and logos are trademarks of Sirius XM Radio Inc. iPod® is a registered trademark of Apple Inc. Garmin® and zumo® are trademarks of Garmin Ltd. or its subsidiaries. Printed in U.S.A. P/N 9925282

®, FREEDOM®, VICTORY®, VICTORY VISION® and VICTORY MOTORCYCLES®.

WARNING

Improper vehicle use can result in SEVERE INJURY or DEATH.

NEVER Operate:

• If you are under the age of 16 and without a driver’s license with motorcycle endorsement

• Under the influence of drugs or alcohol

• Off-road

• With more than one passenger (motorcycle must be equipped with passenger foot pegs)

• With weight that exceeds maximum weight rating

ALWAYS:

• Wear a helmet, eye protection, gloves, long-sleeve shirt, long pants and over-the-ankle boots.

• Make sure any passenger reads and understands all safety labels.

• Be aware of your surroundings and driving conditions.

• Keep both hands on the handlebars and both feet on the footrests when riding.

• Use only genuine VICTORY accessories designed for your model.

AL WAYS USE AN

APPROVED HELMET

AND PROTECTIVE

GEAR.

READ RIDER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND WARNINGS.

Safety Training

Safety training is a top priority for POLARIS. POLARIS strongly encourages you to take a rider education course from the Motorcycle Safety Foundation or another qualified instructor. The course will help you develop or refresh your expertise in safe riding habits through instruction and riding.

For information on Motorcycle Safety Foundation rider education courses in your area, call 1-800 446-9227 or visit their home page at www.msf-usa.org.

NEVER USE WITH

DRUGS OR ALCOHOL.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Reporting Safety Defects . . . . . . . . . . . . . . . . . . . . . . . 17

Identification / Component Location . . . . . . . . . . . . . . . . . . . . . 18

Instruments, Features & Controls. . . . . . . . . . . . . . . . . . . . . . . . 22

Pre-Ride Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Cleaning and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

CB Radio - ICOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

AUX - iPod®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

SiriusXM Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

NAV MP3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Introduction

Thank you for purchasing a Polaris vehicle, and welcome to our world-wide family of Polaris owners. We proudly produce an exciting line of utility and recreational products.

• Snowmobiles

• All-terrain vehicles (ATVs)

• Low emission vehicles (LEVs)

• RANGER® utility vehicles

• VICTORY® motorcycles

• GEM® vehicles For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and

recommendations in this rider’s manual. Keep this manual with the motorcycle, especially when ownership changes. If your rider’s manual is misplaced or damaged, please purchase a replacement from your VICTORY dealer.

All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operator’s perspective when seated in a normal riding position. If you have questions about the operation or maintenance of your motorcycle after you've read this manual, please see your VICTORY dealer. To locate the nearest authorized VICTORY dealer, call 1-800-POLARIS or visit www.polaris.com.

VICTORY motorcycles comply with all federal, state and local safety and emission regulations for the area of intended sale.

Safety

WARNING

About the Rider's Manual

Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual.

This rider’s manual contains information that is essential to safe riding and proper maintenance of your VICTORY motorcycle. Anyone who uses the motorcycle (operators and passengers) must read the rider’s manual before riding. Carefully read and understand the information found in the Safety section. Understand and follow the procedures outlined in the Maintenance section to keep your VICTORY motorcycle in top condition on the road or in storage. Bring the manual with you when you ride. Following the precautions and procedures in the manual will add to your enjoyment and help keep you riding safely. If you lose or damage this manual, you can purchase a new one through any authorized VICTORY dealer. The rider’s manual should be considered part of the motorcycle and remain with it if sold.

Safety Symbols and Signal Words

The following signal words and symbols appear throughout this manual. Your safety and the safety of others is involved when these words and symbols are used. Become familiar with their meanings before reading the manual.

The safety alert symbol indicates a potential for personal injury.

DANGER

A DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

NOTICE indicates a situation that could result in property damage.

The Prohibition Safety Sign indicates an action NOT to take in order to avoid a hazard.

The Mandatory Action Sign indicates an action that NEEDS to be taken to avoid a hazard.

Safety

WARNING

Safe Riding Practices

Improper use of this motorcycle can result in serious injury or death to you, your passenger and others. To minimize the risk of injury, read and understand the information contained in this section before operating the motorcycle. This section contains safety information specific to the VICTORY motorcycle, as well as information about general motorcycle safety. Anyone who rides the motorcycle (operators and passengers) must follow these safety precautions.

Motorcycling has inherent risks.

You can minimize those risks, but you can't eliminate them completely. Even if you're an experienced motorcycle operator or passenger, read all of the safety information in this manual before operating the motorcycle.

• T ake a rider education course from the Motorcycle Safety Foundation or another qualified instructor. The course will help you develop or refresh your expertise in safe riding habits through instruction and riding. For information on Motorcycle Safety Foundation rider education courses in your area, call 1-800-446-9227 or visit their home page at www.msfusa.org.

• Read and understand all information in this rider’s manual.

• Observe all maintenance requirements specified in this manual. For assistance, see the VICTORY Service Manual or your authorized VICTORY dealer.

Design characteristics affect how you should ride the VICTORY motorcycle:

• The motorcycle is designed for on-road use with one rider and one passenger. See the manufacturer’s label (under the rear panel on the console). The label contains the Vehicle Identification Number (VIN) and Gross Vehicle Weight Rating (GVWR) and Gross Axle Weight Rating (GAWR) information. Never exceed the GVWR or the GAWR.

• Riding off-road, riding with more than one passenger, or carrying weight exceeding the maximum weight rating can make handling difficult, which could cause loss of control.

• During the first 500 miles (800 km) of operation, follow all break-in procedures as outlined in the break-in section beginning on page 49. Failure to do so can result in serious engine damage.

• Some VICTORY motorcycles include saddlebags, a windshield, a trunk, or a passenger backrest as standard equipment. To maintain stability, be prepared to reduce the operating speed of motorcycles equipped with these items.

Safety

Safe Riding Practices

Follow these general safe riding practices:

• Before each ride, perform the pre-ride inspections as outlined beginning on page 40.

Failure to do so may result in damage to the motorcycle or an accident.

• Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding

where there is little or no traffic. Practice riding at a moderate speed on various road surfaces and in different weather conditions.

• Know your skills and limits, and ride within them.

• Allow only licensed, experienced operators to ride your motorcycle, and then only after

they have become familiar with its controls and operation. Make sure all riders read and understand this rider’s manual before riding.

• Do not ride when you’re fatigued, ill or under the influence of alcohol, prescription drugs,

over-the-counter drugs or any other drugs. Fatigue, illness, alcohol and drugs can cause drowsiness, loss of coordination and loss of balance. They can also affect your awareness and judgment.

• If your motorcycle operates abnormally, correct the problem immediately. See the

VICTORY Service Manual or an authorized VICTORY dealer.

• Ride defensively, as if you are invisible to other motorists, even in broad daylight. A

motorist's failure to see or recognize a motorcycle is the leading cause of automobile/ motorcycle accidents . Ride where you're clearly visible to other motorists, and observe

their behavior carefully.

• Be especially cautious at intersections, as these are the most likely places for an accident.

• To prevent loss of control, keep your hands on the handlebars and your feet on the

footrests.

• Do not move or operate the motorcycle with the steering locked (with accessory lock), as

the severely restricted steering could result in loss of control.

• Obey the speed limit and adjust your speed and riding technique based on road, weather

and traffic conditions. As you travel faster, the influence of all other conditions increases, which can affect the motorcycle's stability and increase the possibility of losing control.

Safety

Safe Riding Practices

• Reduce speed when:

• the road has potholes, or is otherwise rough or uneven.

• the road contains sand, dirt, gravel or other loose substances.

• the road is wet, icy or oily.

• the road contains painted surfaces, manhole covers, metal grating, railway crossings or other slippery surfaces.

• The weather is windy, rainy or otherwise causing slippery or rapidly changing conditions.

• Traffic is heavy, congested, not allowing sufficient space between vehicles or otherwise not flowing smoothly.

• You are being passed in either direction by a large vehicle that may produce a wind blast in its wake.

• To maximize braking effectiveness, use the front and rear brakes together. Improper braking may cause loss of control or may not slow the vehicle in time to avoid a collision. Be aware of the following braking facts and practices:

• The rear brake provides 40% of the motorcycle's stopping power, at most. Use the front and rear brakes together.

• T o avoid skidding, apply the brakes gradually when the road is wet or rough, or contains loose or other slippery substances.

• If possible, avoid applying the brakes while making a turn. Motorcycle tires have less traction during turns, so braking will increase the possibility of skidding. Bring the motorcycle to the upright position before applying the brakes.

• When approaching a curve, choose a speed and lean angle that allows you to pass through the curve in your own lane without applying the brakes. Excessive speed, improper lean angle or braking in a curve can cause loss of control.

• Ground clearance is reduced when the motorcycle leans. Do not allow components to contact the road surface when leaning the motorcycle in a curve, as this could cause loss of control.

• Retract the sidestand fully before riding. If the sidestand is not fully retracted, it could contact the road surface and cause loss of control.

• Do not tow a trailer. Towing a trailer can make the motorcycle hard to handle.

Anti-Lock Brake System Response (if equipped)

• When the anti-lock brakes engage during a braking event, the rider will feel pulsing at the brake levers. Continue to apply steady pressure to the brakes for the best stopping

performance.

Safety

Safe Riding Practices

Carrying a Passenger

Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests..

To carry a passenger safely:

• Do not exceed the gross vehicle weight rating (GVWR) for your motorcycle. See the

manufacturer’s label (on the left side of the frame at the steering head).

• Direct the passenger to hold onto you or to the passenger hand grips with both hands and

to keep both feet on the passenger footrests. Do not carry a passenger who cannot place both feet firmly on the passenger footrests. A passenger who is not holding on properly, or who cannot reach the passenger footrests, can shift their body erratically, which can make the motorcycle hard to handle and cause loss of control.

• To obtain the best ride and handling characteristics, adjust the rear shock absorber air

pressure. See page 68.

• Before riding, be sure your passenger knows safe riding procedures. Discuss any safety

information unfamiliar to your passenger. A passenger who is unaware of safe riding procedures may distract you or make movements that make the motorcycle hard to handle.

• Adjust your riding style to compensate for the differences in handling, acceleration and

braking caused by the additional weight of the passenger. Failure to do so can cause loss of control.

Protective Apparel

Wear protective apparel to decrease the risk of injury and increase riding comfort.

• Always wear a helmet that meets or exceeds established safety standards. Approved

helmets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Laws in some areas require that you wear an approved helmet. Head injuries are the leading cause of fatalities in accidents involving motorcycles. Statistics prove that an approved helmet is the most effective protection in preventing or reducing head injuries.

• Wear eye protection to protect eyes from wind or airborne particles and objects. Laws in

some areas require that you wear eye protection. VICTORY recommends that you wear approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8, Z87.1, or CE. Make sure protective eyewear is kept clean.

• All riders should wear bright or light-colored and/or reflective clothing to improve

visibility to other motorists. A motorist's failure to see or recognize a motorcycle is the

leading cause of automobile/motorcycle accidents.

• Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from

abrasions, lacerations or burns should the motorcycle fall. Wear boots with low heels, as high heels can catch on pedals or footrests. The combination of boots and pants should completely cover legs, ankles and feet, protecting skin from engine and exhaust system heat.

• Do not wear loose, flowing clothing or long boot laces, as they can catch on handlebars,

levers or footrests, or they can become entangled in the wheels, causing loss of control and serious injury .

Safety

Use of Accessories

Because VICTORY cannot test and make specific recommendations concerning every accessory or combination of accessories sold, the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional weight. Use the following guidelines when choosing and installing accessories:

• Do not install accessories that impair the stability, handling or operation of the motorcycle or operator visibility. Before installing an accessory, be sure that it does not:

• Reduce ground clearance when the motorcycle is either leaned or in a vertical position.

• Limit suspension or steering travel or your ability to operate controls.

• Displace you from your normal riding position.

• Obscure lights or reflectors.

• Bulky or large accessories can cause instability (due to the lifting or buffeting effects of wind) and loss of control.

• Do not install electrical accessories that exceed the capacity of the motorcycle’s electrical system. Never install higher wattage light bulbs than those supplied as original equipment. An electrical failure could result and cause hazardous loss of engine power or lights, or damage to the electrical system. See page 92.

• Use only genuine VICTORY accessories designed for your model.

Modifications

Modifying the motorcycle by removing any equipment or by adding equipment not approved by VICTORY may void your warranty. Such modifications could make the motorcycle unsafe to ride and could result in severe injury to operator or passengers, as well as damage to the motorcycle. Some modifications may not be legal in your area of operation. If in doubt, contact your authorized VICTORY dealer.

Parking the Motorcycle

When leaving the motorcycle unattended, turn the engine off and lock the steering. See page

22. Remove the ignition key to prevent unauthorized use by minors or those without proper

motorcycle certification and training. Park the motorcycle where people are not likely to touch the hot engine or exhaust system or

place combustible materials near these hot areas. Do not park near a flammable source such as a kerosene heater or an open flame, where hot components could ignite combustible materials.

Park the motorcycle on a firm, level surface. Sloped or soft surfaces may not support the motorcycle. If you must park on a slope or soft surface, follow the precautions outlined on page 56.

Safety

Carrying Cargo

Use the following guidelines when attaching cargo or accessories to the motorcycle. Where applicable, these guidelines also refer to the contents of any accessories.

• Keep cargo and accessory weight to a minimum, and keep items as close to the motorcycle

as possible to minimize a change in the motorcycle’s center of gravity. Changing the center of gravity can cause loss of stability and handling and could cause loss of control.

• Distribute weight evenly on both sides of the motorcycle. Maintain even weight

distribution by checking accessories and cargo to make sure they’re securely attached to the motorcycle before riding and whenever you take a break from riding. Uneven weight distribution, or accessories or cargo that shift suddenly while you’re riding can make the motorcycle hard to handle, can cause loss of control, or cargo could fall from the motorcycle creating a hazard for surrounding vehicles.

• Do not attach large or heavy cargo such as sleeping bags, duffel bags or tents to the

handlebars, front fork area or front fender. Cargo or accessories placed in these areas can cause instability (due to improper weight distribution or aerodynamic changes) and could cause loss of control. Such items can also block air flow to the engine and cause overheating that can damage the engine.

• Do not exceed the maximum cargo weight limit of any accessory (see accessory

instructions and labels). Do not attach cargo to an accessory not designed for that purpose. Either circumstance could result in an accessory failure that could cause loss of control.

• Do not attach anything to the motorcycle unless specifically designed for that purpose by

VICTORY.

Saddlebags and Trunk

Whenever operating a motorcycle with saddlebags:

• Never ride at speeds exceeding 80 MPH (120 km/h). Depending on load and weather

conditions, the maximum safe operating speed may be less. Saddlebags, combined with the lifting or buffeting effects of wind, can make the motorcycle unstable and cause loss of control.

• Distribute weight evenly in each of the saddlebags.

• Do not exceed the individual weight limit of each saddlebag or the trunk. A weight

capacity label is attached inside for reference.

• NEVER EXCEED GROSS VEHICLE WEIGHT RATING (GVWR) or the GROSS

AXLE WEIGHT RATING (GAWR), regardless of whether or not the saddlebags and/or trunk are loaded to capacity . Exceeding the weight rating can reduce stability and handling and cause loss of control.

Safety

To loop on frame

(one tiedown each side)

To shock/strut mount, or

rear tip-over bar

(one tiedown each side)

WARNING

Transporting the Motorcycle

If you must transport the motorcycle:

• Use a truck or trailer. Do not tow the motorcycle with another vehicle, as towing will impair the motorcycle's steering and handling.

• Position and restrain the motorcycle so it remains upright on the truck or trailer. If the motorcycle leans to one side, gasoline may leak from the fuel tank and result in a fire hazard or damage to the finish.

• Do not restrain the motorcycle using the handlebars. In front, hook the tiedowns in the loop provided in the bottom of the frame. Place tiedowns as wide apart as possible on the truck or trailer bed for best stability.

Fuel and Exhaust Safety

Always heed these fuel safety warnings when refueling or servicing the fuel system. For fueling procedures, see page 50.

Gasoline is highly flammable and explosive under certain conditions.

• Always exercise extreme caution whenever handling gasoline.

• Always turn off the engine before refueling.

• Always refuel outdoors or in a well-ventilated area.

• Open the fuel cap slowly. Do not overfill the tank. Do not fill the tank neck.

• Do not smoke or allow open flames or sparks in or near the area where refueling is performed or where gasoline is stored.

Gasoline and gasoline vapors are poisonous and can cause severe injury.

• Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you swallow gasoline, inhale more than a few breaths of gasoline vapor, or get gasoline in your eyes, see a physician immediately.

• If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change clothing.

Exhaust gases contain carbon monoxide, a colorless, odorless gas that can cause loss of consciousness or death in a short time.

• Never start the engine or let it run in an enclosed area.

• Never inhale exhaust gases.

Safety

WARNING

Safety Maintenance

Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death. Always perform the safety maintenance procedures as recommended in this manual. Perform maintenance and repairs promptly as outlined in the VICTORY service manual, or see your authorized VICTORY dealer for service.

• Before each ride, perform the Pre-Ride Inspections. See page 40.

• Perform all periodic maintenance at the recommended intervals outlined in the Periodic

Maintenance section beginning on page 59.

• Always maintain proper tire pressure, tread condition and wheel and tire balance. Inspect

tires regularly and replace worn or damaged tires promptly. Use only approved replacement tires. See the VICTORY Service Manual or your authorized VICTORY dealer.

• Always ensure proper steering head bearing adjustment. Regularly inspect the rear shock

absorber and the front forks for fluid leaks or damage. Make any necessary repairs promptly.

• Clean the motorcycle thoroughly to reveal items in need of repair.

• Fasteners must meet original specifications for quality, finish and type to ensure safety.

Use only genuine VICTOR Y replacement parts, and ensure that all fasteners are tightened to the proper torque.

Electromagnetic Interference

This vehicle complies with the requirements of European directive 97/24/EC Chapter 8, United Nations ECE regulation 10 and Canadian ICES-002.

Safety

Gross Vehicle Weight Rating (GVWR)

WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and han-

dling and could cause loss of control. NEVER exceed the GVWR of your motorcycle.

The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR. This capacity is determined by calculating the difference between your motorcycle’s GVWR and wet weight.

Refer to the specification section beginning on page 113 or the Manufacturing Information/ VIN label on the motorcycle frame for model-specific information. See page 17.

When determining the weight you will be adding to your motorcycle, and to ensure you do not exceed the maximum load capacity, include the following:

• operator body weight

• passenger body weight

• weight of all riders’ apparel and items in or on apparel

• weight of any accessories and their contents

• weight of any additional cargo on the motorcycle

Safety

GVWR Information

VIN Number

Tire & Wheel Information

GAWR Information

Date of Manufacture

Safety and Information Labels

Labels are model-specific and market-specific. Your motorcycle may not contain all of the labels shown. See page 85 for seat removal instructions.

1. Windshield Label

2. Vehicle Identification Number (VIN) (on frame, under rear console cover)

3. Operator/Fuel Warning (on rear console cover)

4. Vehicle/Noise Emission Control Information (VECI/NECI) (inside left saddlebag)

5. Cargo Information (in saddlebags and trunk, if equipped)

Reporting Safety Defects

If you believe that your vehicle has a defect that could result in a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Polaris Industries in writing.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or Polaris Industries.

To contact NHTSA, or obtain other information about motor vehicle safety, you may either call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153), visit the NHTSA website at www.safercar.gov, or write to:

ADMINISTRATOR, NHTSA 1200 New Jersey Avenue, SE West Building Washington, DC 20590

Identification

Ignition Key Number

The ignition key number is stamped on the small metal tag attached to the key ring. Remove the tag and record the number on page 113. Store the tag in a safe place.

Additional keys can be copied from one of the original keys. A VICTORY key blank is required. If you lose both original keys, you will need the following:

• Key number (recorded on page 113)

• A new key blank from a VICTORY dealer

• Proof of ownership

• A locksmith or VICTORY dealer with the equipment necessary to cut a new key

Engine Identification Number

The engine number is stamped into the right crankcase behind the rear cylinder. Record the number in the space provided on page 113.

Key Number

Engine Number

Left Side View

1. Spark Plugs

2. Power Port

3. Front Brake Caliper

4. Gear Shift Pedal

5. Operator Footrest

6. Sidestand

7. Oil Drain Plug

8. Oil Filter

9. Passenger Footrest

10. Rear Brake Caliper

11. Diagnostic Connector (in saddlebag)

12.Running Light (Tour)

13. Rear Speakers (Tour)

14. Passenger Hand Grip

15. Rear Shock Air Fitting (under saddlebag door)

Identification

Right Side View

1. Drive Belt Guard

2. Drive Belt

3. Passenger Footrest

4. Drive Sprocket (under cover)

5. Speed Sensor (top of crankcase)

6. Engine Oil Fill Cap / Dipstick

7. Rear Brake Pedal

8. Operator Footrest

9. Front Brake Caliper

10. Passenger Hand Grip

1 1. Reflector

Identification

Top View

1. Windshield

2. Radio Antenna (under dash)

3. Mirror

4. Clutch Fluid Reservoir

5. Clutch Lever

6. Glove Compartment Door

7. Operator Seat

8. Passenger Seat

9. Saddlebag Latch

10. Trim Panel (if equipped)

11. Front Brake Lever

12. Front Brake Fluid Reservoir

13. Fuel Filler Cap Access Door

5 6

13 12

Front View

1. Front Turn Signal (outer light, each side)

2. Wind Deflector

3. Headlamp

4. Driving Lamp (or HID lamp if equipped)

5. Air Filter (front of frame)

6. Tiedown Loop (on frame)

7. Rear Brake Fluid Reservoir

8. Battery

9. Oil Cooler

10. Horn

1 1. Evaporative Emissions Canister

12. Fuel Tank (one each side)

13. Running Light (inner light, each side)

Rear View

1. Turn Signals (uppermost in lens)

2. Tail Lamps (3 each side)

3. Brake Lamps

4. Exhaust Mufflers

5. License Plate Bracket

Identification

Console

1. Speakers

2. Fuel Gauge

3. Speedometer

4. Indicator Lamp Display

5. Multi-Function Display

6. Tachometer

7. Volt Meter

8. Cruise Control Switches (if equipped)

9. Radio Controls

10. Left Handlebar Switch/ Audio Control

Instruments, Features and Controls

Ignition Switch

Place the ignition key in the ignition switch to operate the following functions of the switch.

OFF All electrical circuits are off. The key can be removed. ON All electrical circuits are on. The ignition key cannot be removed. Headlamp, taillight,

ACC Power is supplied to accessory circuits, radio, instruments, turn signals, brake light,

LOCK All electrical circuits are off. The fuel door and glove compartment are locked when

FUEL DOOR See page 23 for instructions.

Ignition Key

The ignition key operates the ignition switch, fuel door, saddlebag door locks and trunk door lock (if equipped). Read the engine starting procedures beginning on page 51 before starting the engine. Store the spare key in a safe place separate from the main key.

Tip: Use a key ring that won’t scratch the finish on the console.

Ignition Lock

Use the ignition lock feature to lock the steering. When locked, the key can be removed.

Tip: The fuel door and glove compartment are locked when the

steering is locked.

1. Turn the handlebars full left.

2. Turn the key to the OFF position.

3. Push the key down while moving it counter-clockwise to the LOCK position.

4. Release the key.

running lights, radio and instrument lights illuminate. Hazard flashers and turn signals can be activated.

windshield motor, horn and hazard (flasher). The key can be removed.

the steering is locked. The key can be removed. See page 22 for instructions.

Locked

Instruments, Features and Controls

Fuel

Door

Release

Fuel

Door

Cap

Holder

Ignition Switch

Fuel Door Lock

1. Turn the handlebars full left.

2. Turn the key to the OFF position.

Tip: Do not push the key down when unlocking the fuel door.

3. Turn the ignition key counter-clockwise to release the fuel door latch. The door will open under light spring tension. See page 50 for fueling procedure.

4. Remove the fuel cap and place it in the cap holder while fueling. Reinstall the fuel cap securely before closing the fuel door.

5. Close the fuel door and press downward to engage the latch.

Tip: The fuel door and glove compartment are locked when the

steering is locked.

Instruments, Features and Controls

Instrument Cluster

The instrument cluster includes the speedometer, tachometer, fuel gauge, volt meter, indicator lamps and multi-function display.

Indicator Lamps

Speedometer

Tachometer

Fuel Gauge

Multi-Function Display

Volt Meter

Speedometer

The speedometer displays vehicle speed in either miles per hour or kilometers per hour. See page 27.

Tachometer

The tachometer displays engine speed in revolutions per minute (RPM). A red line on the face of the gauge indicates the maximum safe engine speed.

WARNING! Excessive engine speed can cause engine damage or failure, which could result in serious injury or death. Do not allow engine speed to exceed the red line.

Fuel Gauge

The fuel gauge displays fuel level. The key must be in the ON or ACC position. For the most accurate reading, sit on the motorcycle and bring it to the upright position.

Volt Meter

When the key is in the ON position, the volt meter displays battery voltage. If the engine is not running, approximate battery voltage displays. If the engine is running, approximate charging voltage displays.

Instruments, Features and Controls

Left Turn

Low Fuel

Cruise Control

Oil Pressure

High Beam

Check Engine

Right Turn

Neutral

Battery Warning

Anti-Lock

Brake System (ABS)

(if equipped)

Indicator Lamps

Lamp Indicates Condition

Neutral This lamp illuminates when the transmission is in neutral and the ignition

High Beam This lamp illuminates when the headlamp switch is set to high beam.

key is in the ON or ACC position.

Check Engine This lamp illuminates momentarily when the ignition switch is in the ON

Turn Signal One arrow flashes when the corresponding turn signal is activated. Both

Low Oil Pressure

position and the engine is off. This indicates proper function. If this lamp

illuminates while the engine is running, contact an authorized VICTORY dealer promptly for diagnosis. The light will remain on if the tilt sensor

shuts down the engine. See page 30. If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists. Retrieve the error codes for diagnosis. See page 27. This lamp is also known as a malfunction indicator lamp (MIL).

arrows flash when the hazard signal is activated. If a bulb fails, or if there

is a short circuit in the signal system, the lamp flashes at more than twice the normal rate.

This lamp illuminates when the ignition switch is in the ON position and the engine is off, indicating that the indicator circuit is functioning properly. This lamp also illuminates if engine oil pressure drops below safe operating pressure. If this lamp illuminates while the engine is running, turn the engine off as soon as safely possible and check the oil level. If the oil level is correct and the lamp remains on after the engine is restarted, turn the engine off immediately.

Instruments, Features and Controls

Gear

Position

Odometer

Trip Odometer

Clock

Temperature

Indicator Lamps

Lamp Indicates Condition

Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of fuel

Low Battery Warning

remains in the fuel tank. This lamp illuminates when battery voltage is low. Make sure the

charging system is operating properly. See page 95.

Cruise Control Engaged

Anti-Lock Brake System Not Activated (if equipped)

Before using the cruise control, read the safety and operation procedures beginning on page 54.

The ABS indicator always illuminates when the key is in the ON position and remains on until the anti-lock system activates, which occurs when vehicle speed exceeds 6 MPH (10 km/h). When the lamp is illuminated, the anti-lock brakes will not activate, but the conventional brake system will continue to operate normally.

Multi-Function Display

Use the mode button to toggle through the modes of the multi-function display . See page 30. Modes available include:

•clock

• gear position

• ambient temperature

• odometer/trip odometer

• fuel range

• average fuel consumption rate

• fuel economy

• trip time (and other trip information)

Instruments, Features and Controls

Avg

881

8.88

88:8

Speed Range Inst Time

TRIP 1 TRIP 2

km / h miles / gal

“Err”

Suspect Parameter Number (SPN)

Error Code

Number (0-9)

Failure Mode

Indicator (FMI)

Multi-Function Display

Engine Error Codes

The error screen displays only when the CHECK ENGINE light is on or when it goes on and off during one ignition cycle. Error codes are not stored. When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine.

If the CHECK ENGINE indicator lamp illuminates, retrieve the error codes from the display.

1. If the error codes are not displayed, use the mode button to toggle until "Err" displays in the clock area.

2. Record the three code numbers displayed in the gear position, temperature and odometer displays.

3. See an authorized VICTORY dealer for code details and diagnosis.

Display Units (Standard/Metric)

The display can be changed to display either standard or metric units of measurement.

Tip: To exit the set-up mode at any time, wait 10 seconds.The display automatically exits and returns to

the odometer display.

Standard Display Metric Display

Distance Miles Kilometers Fuel U.S. Gallons I = Imperial Gallons Liter = Liters Temperature Fahrenheit Celsius Time 12-Hour Clock 24-Hour Clock

Display Units (Standard/Metric)

1. Turn the key to the OFF position.

2. Press and hold the mode button while turning the key to the ON or ACC position.

3. When the display flashes the distance setting, tap the mode button to advance to the desired setting.

4. Press and hold the mode button to save the setting and advance to the next display option.

5. Repeat the procedure to change remaining display settings.

Instruments, Features and Controls

Multi-Function Display

Clock

Tip: The clock must be reset any time the battery has been disconnected or discharged.

1. Turn the key to ON or ACC. Use the mode button to toggle to the odometer display.

Tip: If LOW FUEL is flashing, the display will not enter the CLOCK SET mode.

2. Press and hold the mode button until the hour segment flashes. Release the button.

3. With the segment flashing, tap the mode button to advance to the desired setting.

4. Press and hold the mode button until the next segment flashes. Release the button.

5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the 1-minute segment, step 4 will save the new settings and exit the clock mode.

6. Turn the key to the OFF position.

Odometer/Trip Odometer

The odometer displays the total distance traveled by the vehicle. The trip odometer displays distance traveled since the trip odometer was reset. To view the trip odometer , turn the key to the ON position. Use the mode button to toggle to the trip odometer.

To reset the trip odometer, toggle to the trip odometer, then press and hold the mode button until the trip odometer resets.

Gear Position

Gear position displays only when the vehicle is moving and the clutch is engaged. If the vehicle stops moving, or if the clutch is disengaged, “--” will show in the display.

Temperature

The key must be in the ON or ACC position to display ambient air temperature.

+ 113 hidden pages