Victory 2012 Ness Signature Series, 2012 Vision Tour, Victory Vision Tour, Victory Vision Tour Ness Signature Series Rider's Manual
PMS 419
2012
Rider's Manual
Victory Vision Tour
Ness Signature Series
Victory Vision Tour
California Proposition 65 Warning
This product contains or emits
chemicals known to the state of
California to cause cancer and birth
defects or other reproductive harm.
The text is printed on 100% recycled
with 40% post-consumer waste (PCW).
For your nearest VICTORY dealer,
call 1-800-POLARIS
or visit www.polarisindustries.com
Polaris Sales Inc.,
2100 Hwy. 55, Medina, MN 55340
Phone 1-888-704-5290
Part No. 9923276 Rev 01
Printed in USA
PMS 419
*9923276 *
1
2012 Rider’s Manual
Victory Vision® Tour
Ness Signature Series Victory Vision
®
Tour
2
Copyright© 2011 Polaris Sales Inc.
All information contained within this publication is based on the latest product information available at the time
of publication. Product improvements or other changes may result in differences between this manual and the
motorcycle. Depictions and/or procedures in this publication are intended for reference use only.
No liability can be accepted for omissions or inaccuracies. Polaris Industries reserves the right to make changes at
any time, without notice and without incurring obligation to make the same or similar changes to motorcycles
previously built. Any reprinting or reuse of the depictions and/or procedures contained within, whether whole or
in part, is expressly prohibited.
All reference to RIGHT , LEFT, FRONT, REAR are from the operator’s perspective seated in a normal riding
position.
Features of VICTORY Motorcycles are covered by U.S. Patent Nos: 6,976,691; 6,407,663; D489670; D482311;
D482304; D481980; D481973; D474142.
The following are registered trademarks of Polaris Industries Inc.:
POLARIS
®, THE WAY OUT®, FREEDOM®, VICTORY®, VICTOR Y VISION® and VICTORY MOTOR-
CYCLES
®.
DUNLOP® is a registered trademark of Dunlop Tire Corporation.
LOCTITE® is a registered trademark of Henkel Corporation.
XM Ready® is a registered trademark of XM® Satellite Radio Inc. All rights reserved.
iPod® is a registered trademark of Apple Inc.
Garmin® and zumo® are trademarks of Garmin Ltd. or its subsidiaries.
Printed in U.S.A.
P/N 9923276
3
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Reporting Safety Defects . . . . . . . . . . . . . . . . . . . . . . . 15
Identification / Component Location . . . . . . . . . . . . . . . . . . . . .16
Instruments, Features & Controls. . . . . . . . . . . . . . . . . . . . . . . . 20
Pre-Ride Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Cleaning and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
W arranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
CB Radio - ICOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
AUX - iPod®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
XM Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
NAV MP3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
4
Introduction
Thank you for purchasing a Polaris vehicle, and welcome to our world-wide family of
Polaris owners. We proudly produce an exciting line of utility and recreational products.
• Snowmobiles
• All-terrain vehicles (ATVs)
• RANGER utility vehicles
• Low emission vehicles (LEVs)
• VICTORY MOTORCYCLES
For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and
recommendations in this rider’s manual. Keep this manual with the motorcycle, especially
when ownership changes. If your rider’s manual is misplaced or damaged, please purchase a
replacement from your VICTORY dealer.
All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operator’s
perspective when seated in a normal riding position. If you have questions about the operation or maintenance of your motorcycle after you've read this manual, please see your VICTORY dealer. To locate the nearest authorized VICTORY dealer, call 1-800-POLARIS or
visit www.polarisindustries.com.
VICTORY motorcycles comply with all federal, state and local safety and emission regulations for the area of intended sale.
5
Safety
About the Rider's Manual
Failure to follow recommended precautions and procedures could result in severe injury or death.
Always heed all safety precautions and follow all operation, inspection and maintenance pro c edures
outlined in this manual.
This rider’s manual contains information that is essential to safe riding and proper maintenance of your VICTORY motorcycle. Anyone who uses the motorcyc le (operators and passengers) must read the rider’s manual before riding. Carefully read and understand the
information found in the Safety section. Understand and follow the procedures outlined in
the Maintenance section to keep your VICTORY motorcycle in top condition on the road or
in storage. Bring the manual with you when you ride. Following the precautions and procedures in the manual will add to your enjoyment and help keep you riding safely. If you lose
or damage this manual, you can purchase a new one through any authorized VICTORY
dealer. The rider’s manual should be considered part of the motorcycle and remain with it if
sold.
Safety Symbols and Signal Words
The following signal words and symbols appear throughout this manual. Your safety and the
safety of others is involved when these words and symbols are used. Become familiar with
their meanings before reading the manual.
The safety alert symbol indicates a potential for personal injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.
NOTICE
NOTICE indicates a situation that may result in property damage.
WARNING
6
Safety
Safe Riding Practices
Improper use of this motorcycle can result in serious injury or death to you, your passenger and others.
To minimize the risk of injury, read and understand the information contained in this section before
operating the motorcycle. This section contains safety information specific to the VICTOR Y motorcycle,
as well as information about general motorcycle safety. Anyone who rides the motorcycle (operators
and passengers) must follow these safety precautions.
Motorcycling has inherent risks.
You can minimize those risks, but you can't eliminate them completely. Even if you're an
experienced motorcycle operator or passenger, read all of the safety information in this manual before operating the motorcycle.
• T ake a rider education course from the Motorcycle Safety Foundation or another qualified
instructor. The course will help you develop or refresh your expertise in safe riding habits
through instruction and riding. For information on Motorcycle Safety Foundation rider
education courses in your area, call 1-800-446-9227 or visit their home p age at www.msfusa.org.
• Read and understand all information in this rider’s manual.
• Observe all maintenance requirements specified in this manual. For assistance, see the
VICTORY Service Manual or your authorized VICTORY dealer.
Design characteristics affect how you should ride the VICTORY motorcycle:
• The motorcycle is designed for on-road use with one rider and one passenger. See the
manufacturer’s label (under the rear panel on the console). The label contains the Vehicle
Identification Number (VIN) and Gross Vehicle Weight Rating (GVWR) and Gross Axle
Weight Rating (GAWR) information. Never exceed the GVWR or the GAWR.
• Riding off-road, riding with more than one passenger, or carrying weight exceeding the
maximum weight rating can make handling difficult, which could cause loss of control.
• During the first 500 miles (800 km) of operation, follow all break-in procedures as outlined in the break-in section beginning on page 47. Failure to do so can result in serious
engine damage.
• Some VICTORY motorcycles include saddlebags, a windshield, a trunk, or a passenger
backrest as standard equipment. To maintain stability, be prepared to reduce the operating
speed of motorcycles equipped with these items.
WARNING
7
Safety
Safe Riding Practices
Follow these general safe riding practices:
• Before each ride, perform the pre-ride inspections as outlined beginning on page 38. Fail-
ure to do so may result in damage to the motorcycle or an accident.
• Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding
where there is little or no traffic. Practice riding at a moderate speed on various road surfaces and in different weather conditions.
• Know your skills and limits, and ride within them.
• Allow only licensed, experienced operators to ride your motorcycle, and then only after
they have become familiar with its controls and operation. Make sure all riders read and
understand this rider’s manual before riding.
• Do not ride when you're fatigued or under the influence of alcohol, prescription drugs,
over-the-counter drugs or any other drugs. Fatigue, alcohol and drugs can cause drowsiness, loss of coordination and loss of balance. They can also affect your awareness and
judgment.
• If your motorcycle operates abnormally, correct the problem immediately. See the VIC-
TORY Service Manual or an authorized VICTORY dealer.
• Ride defensively, as if you are invisible to other motorists, even in broad daylight. A
motorist's failure to see or recognize a motorcycle is the leading cause of automobile/
motorcycle accidents. Ride where you're clearly visible to other motorists, and observe
their behavior carefully.
• Be especially cautious at intersections, as these are the most likely places for an accident.
• To prevent loss of control, keep your hands on the handlebars and your feet on the foot-
rests.
• Do not move or operate the motorcycle with the steering locked (with accessory lock), as
the severely restricted steering could result in loss of control.
• Obey the speed limit and adjust your speed and riding technique based on road, weather
and traffic conditions. As you travel faster, the influence of all other conditions increases,
which can affect the motorcycle's stability and increase the possibility of losing control.
8
Safety
Safe Riding Practices
• Reduce speed when:
• the road has potholes, or is otherwise rough or uneven.
• the road contains sand, dirt, gravel or other loose substances.
• the road is wet, icy or oily.
• the road contains painted surfaces, manhole covers, metal grating, railway crossings or other
slippery surfaces.
• The weather is windy, rainy or otherwise causing slippery or rapidly changing conditions.
• Traffic is heavy, congested, not allowing sufficient space between vehicles or otherwise not flowing smoothly.
• You are being passed in either direction by a large vehicle that produces a wind blast in its wake.
• To maximize braking effectiveness, use the front and rear brakes together. Improper brak-
ing may cause loss of control or may not slow the vehicle in time to avoid a collision. Be
aware of the following braking facts and practices:
• The rear brake provides 40% of the motorcycle's stopping power, at most. Use the front and rear
brakes together.
• To avoid skidding, apply the brakes gradually when the road is wet or rough, or contains loose or
other slippery substances.
• If possible, avoid applying the brakes while making a turn. Motorcycle tires have less traction
during turns, so braking will increase the possibility of skidding. Bring the motorcycle to the
upright position before applying the brakes.
• When approaching a curve, choose a speed and lean angle that allows you to pass through
the curve in your own lane without applying the brakes. Excessive speed, improper lean
angle or braking in a curve can cause loss of control.
• Ground clearance is reduced when the motorcycle leans. Do not allow components to contact the road surface when leaning the motorcycle in a curve, as this could cause loss of
control.
• Retract the sidestand fully before riding. If the sidestand is not fully retracted, it could contact the road surface and cause loss of control.
• Do not tow a trailer. Towing a trailer can make the motorcycle hard to handle.
Anti-Lock Brake System Response (if equipped)
• When the anti-lock brakes engage during a braking event, the rider will feel pulsing at the
brake levers. Continue to apply steady pressure to the brakes for the best stopping perfor-
mance.
9
Safety
Safe Riding Practices
Carrying a Passenger
Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests..
To carry a passenger safely:
• Do not exceed the gross vehicle weight rating (GVWR) for your motorcycle.
• Direct the passenger to hold onto you or to the passenger hand grips with both hands and
to keep both feet on the passenger footrests. Do not carry a passenger who cannot place
both feet firmly on the passenger footrests. A passenger who is not holding on properly, or
who cannot reach the passenger footrests, can shift their body erratically, which can make
the motorcycle hard to handle and cause loss of control.
• T o obtain the best ride and handling characteristics, adjust the rear shock absorber air pres-
sure. See page 66.
• Before riding, be sure your passenger knows safe riding procedures. Discuss any safety
information unfamiliar to your passenger. A passenger who is unaware of safe riding procedures may distract you or make movements tha t make the motorcycle hard to handle.
• Adjust your riding style to compensate for the differences in handling, acceleration and
braking caused by the additional weight of the passenger . Failure to do so can cause loss of
control.
Protective Apparel
Wear protective apparel to decrease the risk of injury and increase riding comfort.
• Always wear a helmet that meets or exceeds established safety standards. Approved hel-
mets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Laws
in some areas require that you wear an approved helmet. Head injuries are the leading
cause of fatalities in accidents involving motorcycles. Statistics prove that an approved
helmet is the most effective protection in preventing or reducing head injuries.
• Wear eye protection to protect eyes from wind or airborne particles and objects. Laws in
some areas require that you wear eye protection. VICTORY recommends that you wear
approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8,
Z87.1, or CE. Make sure protective eyewear is kept clean.
• All riders should wear bright or light-colored and/or refl ectiv e clo thin g to impro ve visibil-
ity to other motorists. A motorist's failure to see or recognize a motorcycle is the leading
cause of automobile/motorcycle accidents.
• Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from abra-
sions, lacerations or burns should the motorcycle fall. Wear boots with low heels, as high
heels can catch on pedals or footrests. The combination of boots and pants should completely cover legs, ankles and feet, protecting skin from engin e and exhaust system heat.
• Do not wear loose, flowing clothing or long boot laces, as they can catch on handlebars,
levers or footrests, or they can become entangled in the wheels, causing loss of control and
serious injury.
10
Safety
Use of Accessories
Because VICTOR Y cannot test and make specific recommendations concerning every accessory or combination of accessories sold, the operator is responsible for determining that the
motorcycle can be safely operated with any accessories or additional weight. Use the following guidelines when choosing and installing accessories:
• Do not install accessories that impair the stability , handling or operation of the motorcycle.
Before installing an accessory, be sure that it does not:
• Reduce ground clearance when the motorcycle is either leaned or in a vertical position.
• Limit suspension or steering travel or your ability to operate controls.
• Displace you from your normal riding position.
• Obscure lights or reflectors.
• Bulky or large accessories can cause instability (due to the lifting or buffeting effects of
wind) and loss of control.
• Do not install electrical accessories that exceed the capacity of the motorcycle’s electrical
system. Never install higher wattage light bulbs than those supplied as original equipment.
An electrical failure could result and cause hazardous loss of engine power or lights, or
damage to the electrical system. See page 90.
• Use only genuine VICTORY accessories designed for your model.
Modifications
Modifying the motorcycle by removing any equipment o r by adding equipment not approved
by VICTORY may void your warranty. Such modifications could make the motorcycle
unsafe to ride and could result in severe injury to operator or passengers, as well as damage
to the motorcycle. Some modifications may not be legal in your area of operation. If in
doubt, contact your authorized VICTORY dealer.
Parking the Motorcycle
When leaving the motorcycle unattended, turn the engine off and lock the steering. See page
20. Remove the ignition key to prevent unauthorized use.
Park the motorcycle where people are not likely to touch the hot engine or exhaust system or
place combustible materials near these hot areas. Do not park near a flammable source such
as a kerosene heater or an open flame, where hot components could ignite combustible materials.
Park the motorcycle on a firm, level surface. Sloped or soft surfaces may not support the
motorcycle. If you must park on a slope or soft surface, follow the precautions outlined on
page 54.
11
Safety
Carrying Cargo
Use the following guidelines when attaching cargo or accessories to the motorcycle. Where
applicable, these guidelines also refer to the contents of any accessories.
• Keep cargo and accessory weight to a minimum, and keep items as close to the motorcycle
as possible to minimize a change in the motorcycle’s center of gravity. Changing the center of gravity can cause loss of stability and handling and could cause loss of control.
• Distribute weight evenly on both sides of the motorcycle. Maintain even weight distribu-
tion by checking accessories and cargo to make sure they’re securely attached to the
motorcycle before riding and whenever you take a break from riding. Uneven weight distribution, or accessories or cargo that shift suddenly while you’re riding can make the
motorcycle hard to handle and could cause loss of control.
• Do not attach large or heavy cargo such as sleeping bags, duffel bags or tents to the han-
dlebars, front fork area or front fender. Cargo or accessories placed in these areas can
cause instability (due to improper weight distribution or aerodynamic changes) and could
cause loss of control. Such items can also block air flow to the engine and cause overheating that can damage the engine.
• Do not exceed the maximum cargo weight limit of any accessory (see accessory instruc-
tions and labels). Do not attach cargo to an accessory not designed for that purpose. Either
circumstance could result in an accessory failure that could cause loss of control.
• Do not attach anything to the motorcycle unless specifically designed for that purpose by
VICTORY.
Saddlebags and Trunk
Whenever operating a motorcycle with saddlebags:
• Never ride at speeds exceeding 80 MPH (120 km/h). Depending on load and weather con-
ditions, the maximum safe operating speed may be less. Saddlebags, combined with the
lifting or buffeting effects of wind, can make the motorcycle unstable and cause loss of
control.
• Distribute weight evenly in each of the saddlebags.
• Do not exceed the individual weight limit of each saddlebag or the trunk. A weight capac-
ity label is attached inside for reference.
• NEVER EXCEED GROSS VEHICLE WEIGHT RATING (GVWR) or the GROSS
AXLE WEIGHT RATING (GAWR), regardless of whether or not the saddlebags and/or
trunk are loaded to capacity . Exceeding the wei ght rating can reduce stability and handling
and cause loss of control.
12
Safety
Transporting the Motorcycle
If you must transport the motorcycle:
• Use a truck or trailer . Do not tow the motorcycle
with another vehicle, as towing will impair the
motorcycle's steering and handling.
• Position and restrain the motorcycle so it remains
upright on the truck or trailer. If the motorcycle
leans to one side, gasoline may leak from the fuel
tank and result in a fire hazard or damage to the
finish.
• Do not restrain the motorcycle using the handlebars. In front, hook the tiedowns in the loop provided in the bottom of the frame. Place tiedowns as
wide apart as possible on the truck or trailer bed for
best stability.
Fuel and Exhaust Safety
Always heed these fuel safety warnings when refueling or servicing the fuel system. For
fueling procedures, see page 48.
Gasoline is highly flammable and explosive under certain conditions.
• Always exercise extreme caution whenever handling gasoline.
• Always turn off the engine before refueling.
• Always refuel outdoors or in a well-ventilated area.
• Open the fuel cap slowly. Do not overfill the tank. Do not fill the tank neck.
• Do not smoke or allow open flames or sparks in or near the area where refueling is performed or
where gasoline is stored.
Gasoline and gasoline vapors are poisonous and can cause severe injury.
• Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you swallow gasoline, inhale
more than a few breaths of gasoline vapor, or get gasoline in your eyes, see a physician
immediately.
• If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change
clothing.
Exhaust gases contain carbon monoxide, a colorless, odorless gas that can cause loss of
consciousness or death in a short time.
• Never start the engine or let it run in an enclosed area.
• Never inhale exhaust gases.
To loop on frame
(one tiedown each side)
To shock/strut mount, or
rear tip-over bar
(one tiedown each side)
WARNING
13
Safety
Safety Maintenance
Failure to perform safety maintenance as recommended can result in difficult handling and loss of
control, which could result in serious injury or death. Always perform the safety maintenance
procedures as recommended. Perform maintenance and repairs promptly as outlined in the VICTORY
service manual, or see your authorized VICTORY dealer for service.
• Before each ride, perform the Pre-Ride Inspections. See page 47.
• Perform all periodic maintenance at the recommended intervals outlined in the Periodic
Maintenance section beginning on page 57.
• Always maintain proper tire pressure, tread condition and wheel and tire balance. Inspect
tires regularly and replace worn or damaged tires promptly. Use only approved replacement tires.
• Always ensure proper steering head bearing adjustment. Regularly inspect the rear shock
absorber and the front forks for fluid leaks or damage. Make any necessary repairs
promptly.
• Clean the motorcycle thoroughly to reveal items in need of repair.
• Make sure all legally required equipment is properly installed and in good condition,
including the license plate.
• Fasteners must meet original specifications for quality, finish and type to ensure safety.
Use only genuine VICTORY replacement parts, and ensure that all fasteners are tightened
to the proper torque.
Electromagnetic Interference
This vehicle complies with European directive 97/24/EC Chapter 8 requirements, which is
equivalent to Canadian ICES-002.
WARNING
14
Safety
Gross Vehicle Weight Rating (GVWR)
WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and han-
dling and could cause loss of control. NEVER exceed the GVWR of your motorcycle.
The maximum load capacity of your motorcycle is the maximum weight you may add to
your motorcycle without exceeding the GVWR. This capacity is determined by calculating
the difference between your motorcycle’s GVWR and wet weight.
Refer to the specification section of this manual or the Manufacturing Information/VIN label
on the motorcycle frame for model-specific information. Refer to the “Safety and Information Labels” section in this manual for location on the motorcycle.
When determining the weight you will be adding to your motorcycle, and to ensure you do
not exceed the maximum load capacity, include the following:
• operator body weight
• passenger body weight
• weight of all riders’ apparel and items in or on apparel
• weight of any accessories and their contents
• weight of any additional cargo on the motorcycle
15
Safety
Safety and Information Labels
Labels are model-specific and market-specific. Your motorcycle may not contain all of the
labels shown. See page 83 for seat removal instructions.
1. Windshield Label
2. Vehicle Identification Number (VIN) (on frame, under rear console cover)
3. Operator/Fuel Warning (on rear console cover)
4. Vehicle/Noise Emission Control Information (VECI/NECI) (inside left saddlebag)
5. Cargo Information (in saddlebags and trunk, if equipped)
Reporting Safety Defects
If you believe that your vehicle has a defect that could result in a crash or cause injury or
death, you should immediately inform the National Highway Traffic Safety Administration
(NHTSA) in addition to notifying Polaris Industries in writing.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a
safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or
Polaris Industries.
To contact NHTSA, or obtain other information about motor vehicle safety, you may either
call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153), visit the
NHTSA website at www.safercar.gov, or write to:
ADMINISTRATOR, NHTSA
1200 New Jersey Avenue, SE
West Building
Washington, DC 20 590
GVWR Information
VIN Number
Tire & Wheel Information
GAWR Information
Date of Manufacture
2
3
5
4
1
16
Identification
Ignition Key Number
The ignition key number is stamped on the small metal tag
attached to the key ring. Remove the tag and record the number
on page 107. Store the tag in a safe place.
Additional keys can be copied from one of the original keys. A
VICTORY key blank is required. If you lose both original
keys, you will need the following:
• Key number (recorded on page 107)
• A new key blank from a VICTORY dealer
• Proof of ownership
• A locksmith or VICTORY dealer with the equipment necessary
to cut a new key
Engine Identification Number
The engine number is stamped into the right crankcase behind
the rear cylinder. Record the number in the space provided on
page 107.
Key Number
Engine Number
17
Identification
Left Side View
1. Sp ark Plugs
2. Power Port
3. Front Brake Caliper
4. Gear Shift Pedal
5. Operator Footrest
6. Sidestand
7. Oil Drain Plug
8. Oil Filter
9. Passenger Footrest
10. Rear Brake Caliper
11. Diagnostic Connector (in
saddlebag)
12.Running Light (Tour)
13. Rear Speakers (Tour)
14. Passenger Hand Grip
15. Rear Shock Air Fitting (under
saddlebag door)
Right Side View
1. Drive Belt Guard
2. Drive Belt
3. Passenger Footrest
4. Drive Sprocket (under cover)
5. Speed Sensor (top of crankcase)
6. Engine Oil Fill Cap / Dipstick
7. Rear Brake Pedal
8. Operator Footrest
9. Front Brake Caliper
10. Passenger Hand Grip
11. Reflector
1
3
4
5
6
7
8
9
10
11
12
15
14
13
2
2
1
2
3
4
5
6
7
8
9
10
11
18
Identification
Top View
1. Windshield
2. Radio Antenna (under dash)
3. Mirror
4. Clutch Fluid Reservoir
5. Clutch Lever
6. Glove Compartment Door
7. Operator Seat
8. Passenger Seat
9. Saddlebag Latch
10. Trim Panel (if equipped)
11. Front Brake Lever
12. Front Brake Fluid Reservoir
13. Fuel Filler Cap Access Door
Front View
1. Front Turn Signal (outer light, each
side)
2. Wind Deflector
3. Headlamp
4. Driving Lamp (or HID lamp if
equipped)
5. Air Filter (front of frame)
6. Tiedown Loop (on frame)
7. Rear Brake Fluid Reservoir
8. Battery
9. Oil Cooler
10. Horn
11. Evaporative Emissions Canister
12. Fuel Tank (one each side)
13. Running Light (inner light, each side)
1
2
3
4
5
6
7
8
9
10
11
12
13
3
9
1
2
3
4
5
6
7
8
9
10
11
12
13
19
Identification
Rear View
1. Turn Signals (uppermost in lens)
2. Tail Lamps (3 each side)
3. Brake Lamps
4. Exhaust Mufflers
5. License Plate Bracket
Console
1. Speakers
2. Fuel Gauge
3. Speedometer
4. Indicator Lamp Display
5. Multi-Function Display
6. Tachometer
7. V olt Meter
8. Cruise Control Switches (if
equipped)
9. Radio Controls
10. Left Handlebar Switch/
Audio Control
1
2
3
4
4
5
1
2
3
4
5
6
7
8
9
10
1
20
Instruments, Features and Controls
Ignition Switch
Place the ignition key in the ignition switch to operate the following functions of the switch.
Ignition Key
The ignition key operates the ignition switch, fuel door , saddlebag door locks and trunk door
lock (if equipped). Read the engine starting procedu res begin ning on page 49 be fore starting
the engine. Store the spare key in a safe place separate from the main key.
Tip: Use a key ring that won’t scra tch the finish on the console.
Ignition Lock
Use the ignition lock feature to lock the steering. When
locked, the key can be removed.
Tip: The fuel door and glove compartment are locked when the
steering is locked.
1. Turn the handlebars full left.
2. Turn the key to the OFF position.
3. Push the key down while moving it counter-clockwise
to the LOCK position.
4. Release the key.
OFF All electrical circuits are off. The key can be removed.
ON All electrical circuits are on. The ignition key cannot be removed. Headlamp, taillight,
running lights, radio and instrument lights illuminate. Hazard flashers and turn signals
can be activated.
ACC Power is supplied to accessory circuits, radio, instruments, turn signals, brake light,
windshield motor, horn and hazard (flasher). The key can be removed.
LOCK All electrical circuits are off. The fuel door and glove compartment are locked when
the steering is locked. The key can be removed. See page 20 for instructions.
FUEL DOOR See page 21 for instructions.
Locked
21
Instruments, Features and Controls
Ignition Switch
Fuel Door Lock
1. Turn the handlebars full left.
2. Turn the key to the OFF position.
Tip: Do not push the key down when unlocking the fuel door.
3. Turn the ignition key counter-clockwise to release
the fuel door latch. The door will open under light
spring tension. See page 48 for fueling procedure.
4. Remove the fuel cap and place it in the cap holder
while fueling. Reinstall the fuel cap securely before
closing the fuel door.
5. Close the fuel door and press downward to engage
the latch.
Tip: The fuel door and glove compartment are locked when the
steering is locked.
Fuel
Door
Release
Fuel
Door
Cap
Holder
22
Instruments, Features and Controls
Instrument Cluster
The instrument cluster includes the speedometer, tachometer, fuel gauge, volt meter, indicator lamps and multi-function display.
Speedometer
The speedometer displays vehicle speed in either miles per hour or kilometers per hour. See
page 25.
Tachometer
The tachometer displays engine speed in revolutions per minute (RPM). A red line on the
face of the gauge indicates the maximum safe engine speed.
WARNING! Excessive engine speed can cause engine damage or failure, which could result in
serious injury or death. Do not allow engine speed to exceed the red line.
Fuel Gauge
The fuel gauge displays fuel level. The key must be in the ON or ACC position. For the most
accurate reading, sit on the motorcycle and bring it to the upright position.
Volt Meter
When the key is in the ON position, the volt meter displays battery voltage. If the engine is
not running, approximate battery voltage displays. If the engine is running, approximate
charging voltage displays.
Speedometer
Tachometer
Fuel Gauge
Volt Meter
Indicator Lamps
Multi-Function Display
23
Instruments, Features and Controls
Indicator Lamps
Lamp Indicates Condition
Neutral This lamp illuminates when the transmission is in neutral and the ignition
key is in the ON or ACC position.
High Beam This lamp illuminates when the headlamp switch is set to high beam.
Check Engine This lamp illuminates momentarily when the ignition switch is in the ON
position and the engine is off. This indicates proper function. If this lamp
illuminates while the engine is running, contact an authorized VICTORY
dealer promptly for diagnosis. The light will remain on if the tilt sensor
shuts down the engine. See page 28. If abnormal sensor or engine
operation is detected the light will remain on as long as the fault
condition exists. Retrieve the error codes for diagnosis. See page 25.
This lamp is also known as a malfunction indicator lamp (MIL).
Turn Signal One arrow flashes when the corresponding turn signal is activated. Both
arrows flash when the hazard signal is activated. If a bulb fails, or if there
is a short circuit in the signal system, the lamp flashes at more than
twice the normal rate.
Low Oil
Pressure
This lamp illuminates when the ignition switch is in the ON position and
the engine is off, indicating that the indicator circuit is functioning
properly. This lamp also illuminates if engine oil pressure drops below
safe operating pressure. If this lamp illuminates while the engine is
running, turn the engine off as soon as safely possible and check the oil
level. If the oil level is correct and the lamp remains on after the engine is
restarted, turn the engine off immediately.
Left Turn
Low Fuel
Cruise Control
Oil Pressure
High Beam
Check Engine
Right Turn
Neutral
Battery Warning
Anti-Lock
Brake System (ABS)
(if equipped)
24
Instruments, Features and Controls
Indicator Lamps
Multi-Function Display
Use the mode button to toggle through the modes of the multi-function display. See page 28.
Modes available include:
•clock
• gear position
• ambient temperature
• odometer/trip odometer
• fuel range
• average fuel consumption rate
• fuel economy
• trip time (and other trip information)
Lamp Indicates Condition
Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of fuel
remains in the fuel tank.
Low Battery
Warning
This lamp illuminates when battery voltage is low. Make sure the
charging system is operating properly. See page 93.
Cruise Control
Engaged
Before using the cruise control, read the safety and operation
procedures beginning on page 52.
Anti-Lock Brake
System Not
Activated
(if equipped)
The ABS indicator always illuminates when the key is in the ON position
and remains on until the anti-lock system activates, which occurs when
vehicle speed exceeds 6 MPH (10 km/h). When the lamp is illuminated,
the anti-lock brakes will not activate, but the conventional brake system
will continue to operate normally.
Gear
Position
Odometer
Trip Odometer
Clock
Temperature
25
Instruments, Features and Controls
Multi-Function Display
Engine Error Codes
The error screen displays only when the CHECK
ENGINE light is on or when it goes on and off
during one ignition cycle. Error codes are not
stored. When the key is turned OFF, the code and
message is lost, but will reappear if the fault reoccurs after restarting the engine.
If the CHECK ENGINE indicator lamp illuminates, retrieve the error codes from the display.
1. If the error codes are not displayed, use the
mode button to toggle until "Err" displays in
the clock area.
2. Record the three code numbers displayed in
the gear position, temperature an d odometer
displays.
3. See an authorized VICTORY dealer for code details and diagnosis.
Display Units (Standard/Metric)
The display can be changed to display either standard or metric units of measurement.
Tip: To exit the set-up mode at any time, wait 10 seconds.The display automatically exits and returns to
the odometer display.
Display Units (Standard/Metric)
1. Turn the key to the OFF position.
2. Press and hold the mode button while turning the key to the ON or ACC position.
3. When the display flashes the distance setting, tap the mode button to advance to the
desired setting.
4. Press and hold the mode button to save the setting and advance to the next display
option.
5. Repeat the procedure to change remaining display settings.
Standard Display Metric Display
Distance Miles Kilometers
Fuel U.S. Gallons I = Imperial Gallons Liter = Liters
Temperature Fahrenheit Celsius
Time 12-Hour Clock 24-Hour Clock
Avg
C
F
8
881
88
:
88
8.88
:
88:8
Speed Range Inst Time
TRIP 1
TRIP 2
km / h
miles / gal
“Err”
Suspect Parameter Number (SPN)
Error Code
Number (0-9)
Failure Mode
Indicator (FMI)
26
Instruments, Features and Controls
Multi-Function Display
Clock
Tip: The clock must be reset any time the battery has been disconnected or discharged.
1. Turn the key to ON or ACC. Use the mode button to toggle to the odometer display.
Tip: If LOW FUEL is flashing, the display will not enter the CLOCK SET mode.
2. Press and hold the mode button until the hour segment flashes. Release the button.
3. With the segment flashing, tap the mode button to advance to the desired setting.
4. Press and hold the mode button until the next segment flashes. Release the button.
5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the
1-minute segment, step 4 will save the new settings and exit the clock mode.
6. Turn the key to the OFF position.
Odometer/Trip Odometer
The odometer displays the total distance traveled by the vehicle. The trip odometer displays
distance traveled since the trip odometer was reset. To view the trip odometer , turn the key to
the ON position. Use the mode button to toggle to the trip odometer.
To reset the trip odometer, toggle to the trip odometer, then press and hold the mode button
until the trip odometer resets.
Gear Position
Gear position displays only when the vehicle is moving and the clutch is engaged. If the
vehicle stops moving, or if the clutch is disengaged, “--” will show in the display.
Temperature
The key must be in the ON or ACC position to display ambient air temperature.
Loading...