Page 1
Infrared heater controllers
Get the best from
infrared heaters
Page 2
HLVR2controller
■ Suitable for
appliances up to 3kW
at 220-240V
■ Integral ON/OFF
switch
■ Fully adjustable
power setting
■ High reliability triac
used
■ CE EMC compliant
■ UL approved
Victory lightinginfrared heaters can be used
in a variety of applications and are highly
versatile – even more so when used in
conjunction with a controller.
A controller can be used to vary heat output, or
time the period of use, makingthe heater as
environmentally-friendly as possible,and saving
energy cost.
These low cost,compact units are easy to install and
need minimum maintenance.
Fully adjustable from 0-100%,the
HLVR2will help ensure a comfortable
temperature is always achieved whilst
also savingon wasted energy and costs. It
can be used in both indoor and outdoor
applications and can control multiple heaters simultaneously.
It is robust, user friendly, and easy to install.
The HLVR2can also be used for any devices up to 3kW total.
HLWDIM controller
■ Suitable for up
to 1.5kW infra
red heater
■ Waterproof (IP55)
VLRC2controller
■ Suitable for up to
2kW infra red heater
■ Remote control
operation
■ Can be used indoors
and outdoors
■ LED shows status
■ Stepped power
setting
■ High reliability
triac used
■ CE & EMC compliant
■ IP65 -suitable for
outdoor use
■ ON/OFF, and
4-stagedimming
■ 20 metre remote
range
HLPSS4 soft-startcontroller
■ Extends lamp life and saves energy
■ Soft-start/zero-voltage switch-o
■ Suitable for multiple heaters
■ Low-cost
■ Easy to install
The HLWDIM incorporates a soft-startfunction to eliminate
the lampʼshighinrush current — potentially increasing
lamp life by as much as 30% and reducingthe stress
on the mains supply.
Output levels are selected by up & down push
buttons with a high intensity LED indicatingwhen
the controller is givingoutput to the heater.
The VLRC2is a remotely controlled on/oswitch with a
four-stagestepped dimming function operated by a
small hand-heldremote control fob.
The remote control has a range
of 20meters (depending on local
environmental conditions).
The HLPSS4 4kW controllerprovides energy saving when
used with infrared heaters and also prolongs the lampsʼ
life. It does this by soft-startingthe load when power is rst
applied to the heater(s).
The microcontroller-basedunit incorporates
zero-voltageswitching and its soft-startfunction
eliminates lampsʼ initial high inrush current –
potentially increasinglamp life by as much as 30%. It
can be used with multiple heaters.
Page 3
HLOPIR3PIR
controller
■ 12m detection
range with 200°
area detection
■ Suitable for up to
3kW infra red heaters
■ Head twists
up or down
VLFS-3WiFi
fused spur
■ Available for
Android and iOS
■ Can reduce running
costs if unwanted
programmes
are cancelled
■ 13A suitable for 3kW
■ IP55 weatherproof
rating
■ Adjustable heat ON*
time 5 secs – 18 mins
■ Manual ON/
OFF override
■ Hinged back box
for ease of wiring
■ Adjustable light
level control
■ Supports multiple
devices and users
■ Auto, permanent ON,
permanent OFF
and holidaymodes
■ Optional 1 and
2 hour boost
■ IP66 weatherproof
version available
■ Manual override
The HLOPIR3 utilises passive infrared technologyto
detect heat radiation of movinghuman bodies. Upon
detection, the attached heating load will activate for a
user-determined time period. This product is suitable
for wall or ceilingmounting.
* (We recommend a minimum time
of two minutes to prolong the life
of the infra red lamp.)
Ideal for switchinglightingand electrical heaters with
a Weathersafe IP66 version VLFS-3IPfor outdoor uses.
Programme settings are all activated via your
mobile device, givingyou access to control
your installation at any time, no matter
where you are. Total13A3kW control
with conrmation of settingsand
switchingstatus of the connected
appliance via the on-screenapp.
VLTIM4outdoor timer
■ Easy to t
■ Instant on/o -no delay
■ IP66 -use in wet conditions
■ Loads up to 16A-can control
multiple heaters (ie up to 3680W@ 230V)
■ Supplied with dedicated surface
mounting waterproof back box
HLOTIM3timer
■ Suitable for up to
6kW infra red heaters
at 220-240vsupply
■ Electronic soft start-
extends lamp life
■ Tamper proof
push button
■ Fully adjustable
time delay
■ No retriggering
of switch
■ Red LED indicator
when active
■ Waterproof
(IP55 rated)
Thishigh quality, attractive timer switch can be
used for timed operation of infrared heaters
and other appliancesin outdoor environments.
It is Ideal for use in smokingareas, outdoor
seating,gardens and patios.
Featuring a backlitblue neon indicator ring to
aid location in the dark,these intelligent units
have the ability to latch back on to the mains
power supply and reset in the event of a
power cut.
The soft start feature of the HLOTIM3 helps to
prolong the life of infrared lamps and reduces
stress on the mains supply.
Users can instantlyswitch on heaters,
and the electronic timer will switch o the
equipment after a pre-set delay. A single
controller can control up to four 1.5kW,three 2kW,
or one 6kW heater(s). It can easily be retrotted to existing
equipment. Theswitch is tamper proof to prevent abuse and
cannot be re-activateduntil the timer has turned o.
VLPTDtimer
■ 0-99minute countdown timer
■ LED shows time remaining
in minutes
■ Suitable for up to 2kW
■ Can control 1 or 2 heaters
The VLPTD is a 0-99minute digitalcountdown timer with
built-instart/stop.Time is set by two buttons in steps of
1 or 10 minutes.
The VLPTD is primarily for use with Victorysmall paint
driers and is mounted onto the HLPS paint dryer stand. It
is supplied with a 3m supply cable and tted with a 13AUK
plug. The VLPTD-Eversion is tted with 16AEU Plug.
Page 4
Technical data
Power
controller
WiFi
fused spur
PIR power
controller
HLVR2 HLWDIM VLRC2
Supply voltage 200 – 264V 50/60Hz 230V ±10%, 50Hz 220 – 240V 50/60Hz
Max current rating 15A 6.5A @ 25°C ambient 9A @ 25°Cambient
Peak surgecurrent 240A
Min holding load current 30mA
Operating temperature -20°C – +50°C -20°C – +40°C
Dimensions 86 x 146 x 47mm
68mm inc. knob
Weight 0.55 kg 0.5kg 0.6kg
Protection rating IP55 IP65
Notes Must be mounted proud of a
wall and not recessed into a
cavity.
30mA
95 x 130 x 55mm 120 x 80 x 55mm
Supplied with:
2 x cable gland
Wall mounting screws
Supplied with:
2 x cable glands
Mounting bracket accessory
Hand held remote
Dimming stages:
Step 1 40% / Step 2 70%
Step 3 78% /Step 4 Full
HLPSS4 VLFS-3/ VLFS-3IP HLOPIR3
Supply voltage 230V +/-10% 50 Hz 230V AC 50 Hz 230V
Switchingcapacity 4kW max. 13AResistive (3kW) 3kW max.
Supply fusing 20LCTor MCB20A (1 pole, 440V) BS1362 13A Fuse
Current consumption 50mA
Terminals
Operating temperature -20– +40°C 0°C – +40°C
Dimensions 100 x 100 x 60mm 85 x 85 x 44mm 87 x 73 x 121mm
Weight 0.34kg 0.2kg
Protection rating IP65 VLFS-3:indoor only
Notes WiFi 2.4GHz b/g/n
2.5mm
2
rising clamp
VLFS-3IP: IP66
Manual override
Detection range 12m
Detection angle 200°
Lamp on time 5 sec. – 18mins.
Timer
VLTIM4 HLOTIM3 VLPTD
Supply voltage 240v AC 50Hz 220 – 240V AC 50Hz 220 – 240V AC 50Hz
Max current rating 16Afor all general load types 25A@ 230v AC 9A @25°C
Delay time range 2 minutes – 2 hours 5 – 70 minutes
Dimensions Faceplate: 85 x 85 x 9mm
Backbox : 75 x 75 x 60mm (excl.
cable glands)
Weight 0.2kg 0.375kg 1.1kg
Protection rating IP66 (provided the correct IP66
rated connectionsare made).
Notes Can also be used to switch
contactors if a capacitor (PFCC-
1) is tted across the coil.
Supplied with backbox,seals
and mounting screws.
110 x 168x 80mm 260 x 150 x 100mm
Fitted with twin IEC mains
sockets and 1 x IEC cable with
plug.Mounts on HLPS stand.
Distributed by
Victory Lighting(UK) Ltd
www.victorylighting.co.uk email: sales@victorylighting.co.uk
tel +44(0)1525 487960
© Victory Lighting (UK) Ltd 2020
The information contained in thisliterature is for general information purposes only. VictoryLighting(UK) Ltd endeavours
to k=eepthe information up to date and correct, but makes no representations or warranties of any kind,express or
implied,about the completeness, accuracy, reliability, suitability or availability with respect to the information, products,
services, or related graphics contained in this literature.
Victory Lighting(UK) Ltd accepts no liabilityfor any loss or damage including without limitation, indirect or consequential
Controllers v4.3
loss or damage,or any loss or damage whatsoever arising from loss of data or prots arisingout of, or in connection with,
the use of thisliterature.
Loading...