Victory Hammer S 8Ball 2013, Vegas Jackpot 2013, Vegas 8Ball 2013, High Ball 2013, Judge 2013 Owner's manual

...

2013 Owner's Manual

Hammer® S

Hammer 8-Ball®

Vegas Jackpot®

Vegas 8-Ball®

High-Ball®

Victory Judge™

Victory Boardwalk™

California Proposition 65 Warning

This product contains or emits

chemicals known to the state of

California to cause cancer and birth

defects or other reproductive harm.

The text is printed on 100% recycled

with 40% post-consumer waste (PCW).

For your nearest Polaris dealer, call 1-800-POLARIS or visit www.polarisindustries.com Polaris Sales Inc., 2100 Hwy. 55, Medina, MN 55340 Phone 1-888-704-5290 Part No. 9924064 Rev 01 Printed in USA

*9924064 *

2013

Victory Owner’s Manual

Hammer® S Hammer 8-Ball® Vegas Jackpot®

Vegas 8-Ball®

High-Ball®

Victory Judge™

Victory Boardwalk™

All material in this publication is based on the latest product information at the time of publication. Due to constant improvements in the design and quality of production components, some minor discrepancies may result between the actual vehicle and the information presented in this publication. Depictions and/or procedures in this publication are intended for reference use only. No liability can be accepted for omissions or inaccuracies. Polaris Industries reserves the right to make changes at any time, without notice and without incurring obligation to make the same or similar changes to previously manufactured vehicles. Any reprinting, reuse or redistribution of the material in this document is expressly prohibited.

Features of VICTORY Motorcycles are covered by U.S. Patents: 6,976,691; 6,407,663; D489670; D482311; D482304; D481980; D481973; D474142. Refer also to the patent label on the motorcycle.

The following are registered trademarks of Polaris Industries Inc.: POLARIS, THE WAY OUT, FREEDOM, HAMMER, HAMMER 8-BALL, VEGAS, VEGAS JACKPOT, VEGAS 8-BALL, HIGH-BALL, VICTORY and VICTORY MOTORCYCLES.

VICTORY JUDGE and VICTORY BOARDWALK are trademarks of Polaris Industries Inc.

DUNLOP is a registered trademark of Dunlop Tire Corporation.

Printed in U.S.A.

P/N 9924064

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Reporting Safety Defects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Instruments, Features and Controls. . . . . . . . . . . . . . . . . . . . . . 23

Pre-Ride Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Identification Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Maintenance Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Introduction

Thank you for purchasing a Polaris vehicle, and welcome to our world-wide family of Polaris owners. We proudly produce an exciting line of utility and recreational products.

• Snowmobiles

• All-terrain vehicles (ATVs)

• RANGER® utility vehicles

• Low emission vehicles (LEVs)

• Victory Motorcycles®

For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and recommendations in this owner’s manual. Keep this manual with the motorcycle, especially when ownership changes. If your owner’s manual is misplaced or damaged, please purchase a replacement from your VICTORY dealer.

All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operator’s perspective when seated in a normal riding position. If you have questions about the operation or maintenance of your motorcycle after you've read this manual, please see your VICTORY dealer. To locate the nearest authorized VICTORY dealer, call 1-800-POLARIS or visit www.polarisindustries.com.

VICTORY motorcycles comply with all federal, state and local safety and emission regulations for the area of intended sale.

Safety

WARNING

About the Owner's Manual

Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual.

Please read your VICTORY owner’s manual. This manual contains information essential to safe riding and proper maintenance of the motorcycle. Anyone who rides the motorcycle (operators and passengers) must read the owner's manual before riding.

Read and understand the information found in the safety section, and bring the manual with you when you ride. Following the safety precautions and procedures will add to your riding enjoyment and ensure a safe ride.

Understand and follow all inspection and maintenance procedures outlined in this manual. Following these procedures will ensure that your motorcycle remains in safe operating condition at all times.

Safety

Safety Terms and Signal Words

The following signal words and symbols appear throughout this manual and on your vehicle. Your safety and the safety of others is involved when these words and symbols are used. Become familiar with their meanings before reading the manual.

The safety alert symbol indicates a potential personal injury hazard.

DANGER

A DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.

WARNING

A WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.

CAUTION

A CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

NOTICE

A NOTICE indicates a situation that could result in property damage.

Safety

WARNING

Safe Riding Practices

Improper use of this motorcycle can result in serious injury or death to you, your passenger and others. To minimize the risk of injury, read and understand the information contained in this section before operating the motorcycle. Anyone who rides the motorcycle (operators and passengers) must follow these safety precautions.

Motorcycling has inherent risks.

You can minimize those risks, but you can't eliminate them completely. Even if you're an experienced motorcycle operator or passenger, read all of the information in this safety section before operating the motorcycle.

• Take a rider education course from the Motorcycle Safety Foundation or another qualified instructor. The course will help you develop or refresh your expertise in safe riding habits through instruction and riding. For information on Motorcycle Safety Foundation rider education courses in your area, call 1-800-446-9227 or visit their web site at www.msfusa.org.

• Read and understand all information in this owner's manual.

• Observe all maintenance requirements specified in this manual. For assistance, see the VICTORY Service Manual or your authorized VICTORY dealer.

Design characteristics affect how you should ride the VICTORY motorcycle.

• The motorcycle is designed for on-road use with one rider and one passenger. See page 10.

• Do not exceed the gross vehicle weight rating (GVWR). See the specifications section beginning on page 94 or the certification label on the steering head. Riding off-road, riding with more than one passenger, or carrying weight exceeding the maximum weight rating can make handling difficult, which could cause loss of control.

• Be prepared to reduce speed to maintain stability if your motorcycle is equipped with features such as saddlebags, a windshield or a passenger backrest.

Safety

Safe Riding Practices

Follow these general safe riding practices:

• Before each ride, perform the pre-ride inspections. See page 32.

• Follow all break-in procedures during the first 500 miles (800 km) of operation. See page

43.

• Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding where there is little or no traffic. Practice riding at a moderate speed on various road surfaces and in different weather conditions.

• Know your skills and limits, and ride within them.

• Allow only licensed, experienced operators to ride your motorcycle, and then only after they have become familiar with its controls and operation. Make sure all riders read and understand this owner’s manual before riding.

• Do not ride when you're fatigued or under the influence of alcohol, prescription drugs, over-the-counter drugs or any other drugs.

• If your motorcycle operates abnormally, correct the problem immediately. See the VIC- TORY Service Manual or your authorized VICTORY dealer. Continued operation could aggravate the initial problem, increase the cost of repairs and threaten your safety.

• Ride defensively, as if you are invisible to other motorists, even in broad daylight. A

motorist's failure to see or recognize a motorcycle is the leading cause of automobile/ motorcycle accidents. Ride where you're clearly visible to other motorists, and observe

their behavior carefully.

• Be especially cautious at intersections, as these are the most likely places for an accident.

• To prevent loss of control, keep your hands on the handlebars and your feet on the footrests.

• Do not move or operate the motorcycle with the steering locked (if equipped), as the severely restricted steering could result in loss of control.

• Obey the speed limit and adjust your speed and riding technique based on road, weather and traffic conditions. As you travel faster, the influence of all other conditions increases, which can affect the motorcycle's stability and increase the possibility of losing control.

Safety

Safe Riding Practices

• Reduce speed when:

- the road has potholes or is otherwise rough or uneven.

- the road contains sand, dirt, gravel or other loose substances.

- the road is wet, icy or oily.

- the road contains painted surfaces, manhole covers, metal grating, railway crossings or other slippery surfaces.

- weather is windy, rainy or otherwise causing slippery or rapidly changing conditions.

- traffic is heavy, congested, not allowing sufficient space between vehicles or otherwise not flowing smoothly.

- being passed in either direction by a large vehicle that produces a wind blast in its wake.

• To maximize braking effectiveness, use the front and rear brakes together. Be aware of the following important information:

- The rear brake provides 40% of the motorcycle's stopping power, at most.

- To avoid skidding, apply the brakes gradually when the road is wet or rough, or contains

loose or other slippery substances.

- If possible, avoid applying the brakes while making a turn. Motorcycle tires have less

traction during turns, so braking will increase the possibility of skidding. Bring the motorcycle to the upright position before applying the brakes.

• To avoid loss of control:

- Retract the sidestand fully before riding. Ground clearance is reduced when the motor-

cycle leans.

- When approaching a curve, choose a speed and lean angle that will allow you to pass

through the curve in your own lane without applying the brakes.

- Do not allow components to contact the road surface when leaning in a curve.

- Do not tow a trailer, which can make the motorcycle hard to handle.

Safety

Safe Riding Practices

Carrying a Passenger

Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests.

To carry a passenger safely:

• Do not exceed the gross vehicle weight rating (GVWR).

• If necessary, adjust the rear shock preload. See page 58. Improper preload adjustment can make your motorcycle hard to handle and can cause loss of control.

• Before riding, be sure your passenger is familiar with safe riding procedures. An inexperienced passenger may distract you or make movements that cause instability.

• Direct the passenger to hold onto you or the seat strap with both hands and to keep both feet on the passenger footrests. Do not carry a passenger who cannot place both feet firmly on the passenger footrests. A passenger who rides improperly can shift body weight erratically and cause instability.

• Adjust your riding style to compensate for the differences in handling, acceleration and braking caused by the additional weight of the passenger.

Safety

Safe Riding Practices

Protective Apparel

Wear protective apparel to decrease the risk of injury and increase riding comfort.

• Always wear a helmet that meets or exceeds established safety standards. Approved hel-

mets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Laws in some areas require that you wear an approved helmet. Head injuries are the leading cause of fatalities in accidents involving motorcycles. Statistics prove that an approved helmet is the most effective protection in preventing or reducing head injuries.

• Wear eye protection to protect eyes from wind or airborne particles and objects. Laws in

some areas require that you wear eye protection. VICTORY recommends that you wear approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8, Z87.1, or CE. Make sure protective eyewear is kept clean.

• All riders should wear bright or light-colored and/or reflective clothing to improve visibil-

ity to other motorists. A motorist's failure to see or recognize a motorcycle is the leading

cause of automobile/motorcycle accidents.

• Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from abra-

sions, lacerations or burns should the motorcycle fall. Wear boots with low heels, as high heels can catch on pedals or footrests. The combination of boots and pants should completely cover legs, ankles and feet, protecting skin from engine and exhaust system heat.

• Do not wear loose, flowing clothing or long boot laces, as they can catch on handlebars,

levers or footrests, or they can become entangled in the wheels, causing loss of control and serious injury.

Safety

Gross Vehicle Weight Rating (GVWR)

WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and

handling and could cause loss of control. NEVER exceed the GVWR of your motorcycle.

The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR. This capacity is determined by calculating the difference between your motorcycle’s GVWR and wet weight.

Refer to the specification section of this manual or the Manufacturing Information/VIN label on the motorcycle frame for model-specific information. Refer to the “Safety and Information Labels” section in this manual for location on the motorcycle.

When determining the weight you will be adding to your motorcycle, and to ensure you do not exceed the maximum load capacity, include the following:

• operator body weight

• passenger body weight

• weight of all riders’ apparel and items in or on apparel

• weight of any accessories and their contents

• weight of any additional cargo on the motorcycle

Carrying Cargo

Use the following guidelines when attaching cargo or accessories to the motorcycle.

To prevent instability and loss of control:

• Keep cargo and accessory weight to a minimum. Keep items as close to the motorcycle as possible to minimize a change in the motorcycle's center of gravity.

• Distribute weight evenly on both sides of the motorcycle and secure cargo to prevent unexpected shifting. Check all accessories and cargo for security and even distribution before riding and at each riding break.

• Do not attach large or heavy cargo such as sleeping bags, duffel bags or tents to the handlebars, front fork area or front fender. These areas are not designed to carry cargo. Cargo in these areas can also block air flow to the engine and cause overheating.

• Do not exceed the maximum cargo weight limit of any accessory. Refer to the accessory instructions and labels. Do not attach cargo to an accessory not designed for that purpose.

• Do not attach anything to the highway bar except highway footrests.

Safety

Carrying Cargo

Saddlebags

When operating a motorcycle equipped with saddlebags:

• Never ride at speeds exceeding 80 MPH (120 km/h). Depending on load and weather con-

ditions, the maximum safe operating speed may be less. Saddlebags, combined with the lifting or buffeting effects of wind, can cause instability.

• Distribute weight evenly in each of the saddlebags.

• Do not exceed the maximum cargo capacity of the saddlebags.

• Do not exceed the gross vehicle weight rating (GVWR).

Parking the Motorcycle

When leaving the motorcycle unattended, turn the engine off and remove the ignition key. Park the motorcycle where people are not likely to touch the hot engine or exhaust system or

place combustible materials near these hot areas. Do not park near a flammable source such as a kerosene heater or an open flame, where hot components could ignite combustible materials.

Park the motorcycle on a firm, level surface. Sloped or soft surfaces may not support the motorcycle. See page 48.

Modifications

Modifying the motorcycle by removing any equipment or by adding equipment not approved by VICTORY may void your warranty. Such modifications may make the motorcycle unsafe to ride and could result in severe injury to operator or passengers, as well as damage to the motorcycle. Some modifications may not be legal in your area of operation. If in doubt, contact your authorized VICTORY dealer.

Safety

Slide turn signal upward.

Restrain with 2 straps

on each side.

VEGAS

(Models differ in appearance, but

locations are the same as shown)

Transporting the Motorcycle

When transporting the motorcycle:

• Use a truck or trailer. Never tow the motorcycle. Towing will impair steering and handling.

• Restrain the motorcycle in an upright position to prevent fuel leaks.

• Place the transmission in neutral.

• Do not place restraints on the handlebars. Loosen the front turn signal mounts and slide them upward. Place tiedown straps around the fork tubes above the lower triple clamp. Secure the rear of the motorcycle with tiedowns around both sides of the swingarm, being careful to avoid the brake line, exhaust and drive belt. Reposition the turn signals before

operating the motorcycle.

Safety

Accessory Selection and Installation

Use the following guidelines when choosing and installing accessories:

• Do not install accessories that impair the stability, handling or operation of the motorcycle.

Before installing an accessory, be sure that it does not:

- Reduce ground clearance when the motorcycle is either leaning or upright.

- Limit suspension or steering travel or your ability to operate controls.

- Displace you from your normal riding position.

- Obscure lights or reflectors.

• Do not install bulky or large accessories that can cause instability (due to the lifting or buf-

feting effects of wind).

• Do not install electrical accessories that exceed the capacity of the electrical system.

Never install higher wattage light bulbs than those supplied as original equipment. An electrical failure could result and cause hazardous loss of engine power or lights, or damage to the electrical system.

• Always install accessories designed and approved by VICTORY specifically for your

model, especially a windshield, backrest or luggage rack. An improperly designed or installed accessories can reduce stability, causing loss of control. Follow the instructions for proper installation and use.

Safety

WARNING

Fuel and Exhaust Safety

Gasoline is highly flammable and explosive under certain conditions.

• Always exercise extreme caution whenever handling gasoline.

• Always turn off the engine before refueling.

• Always refuel outdoors or in a well-ventilated area.

• Open the fuel cap slowly. Do not overfill the tank. Do not fill the tank neck.

• Do not smoke or allow open flames or sparks in or near the area where refueling is performed or where gasoline is stored.

Gasoline and gasoline vapors are poisonous and can cause severe injury.

• Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you swallow gasoline, inhale more than a few breaths of gasoline vapor, or get gasoline in your eyes, see a physician immediately.

• If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change clothing.

• If gasoline spills on the any part of the motorcycle, immediately rinse it off with water.

Exhaust gases contain carbon monoxide, a colorless, odorless gas that can cause loss of consciousness or death in a short time.

• Never start the engine or let it run in an enclosed area.

• Never inhale exhaust gases.

Safety

WARNING

Safety Maintenance

Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death. Always perform the safety maintenance procedures as recommended. Perform maintenance and repairs promptly as outlined in the VICTORY Service Manual, or see your authorized VICTORY dealer for service.

• Before each ride, perform the pre-ride inspections. See page 32.

• Perform maintenance at the intervals specified in the periodic maintenance table. See page

50.

• Always maintain proper tire pressure, tread condition and wheel and tire balance. Inspect

tires regularly and replace worn or damaged tires promptly. Use only approved replacement tires.

• Always ensure proper steering head bearing adjustment.

• Regularly inspect the rear shock absorber and the front forks for fluid leaks or damage.

Make any necessary repairs promptly.

• Clean the motorcycle thoroughly to reveal items in need of repair. See page 79.

• Make sure all legally required equipment is properly installed and in good condition,

including the license plate.

• Fasteners must meet original specifications for quality, finish and type to ensure safety.

Use only genuine VICTORY replacement parts, and ensure that all fasteners are tightened to the proper torque.

Safety

Electromagnetic Interference

This vehicle complies with European directive 97/24/EC Chapter 8 requirements, which is equivalent to Canadian ICES-002.

Reporting Safety Defects

If you believe that your vehicle has a defect that could result in a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Polaris Industries in writing.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or Polaris Industries.

To contact NHTSA, or obtain other information about motor vehicle safety, you may call the Vehicle Safety Hotline toll free at 1-888-327-4236 (TTY: 1-800-424-9153), visit the NHTSA web site at www.safercar.gov, or write to:

ADMINISTRATOR, NHTSA 1200 New Jersey Avenue, SE West Building Washington, DC 20590

Safety and Information Labels

Warning

Label

Manufacturing

Information

Label (VIN)

Engine Identification Number

(stamped on right rear

crankcase half)

Emission Control, Noise Information

Label

Tire Warning Label

(if applicable)

Patent Notice

Tire Warning

Label

(if applicable)

Due to different model and market requirements, your vehicle may not have all of the labels shown. Labels that apply to your model will be located as shown.

Handlebar Position Warning Label

(if equipped)

Safety

(under side cover, on side of fuse box cover)

Fuse and Relay Label

Fuse Box Removal Instruction Label

(on base of fuse box)

Component Identification

(Models differ in appearance, but

locations are the same as shown)

Handlebar Area

1. Clutch Lever

2. Mirror

3. Speedometer

4. Indicator Light Panel

5. Tachometer (if equipped)

6. Front Brake Fluid Reservoir

7. Front Brake Lever

8. Throttle Control Grip

9. Switches

10. Throttle Cables

11. Fuel Cap

Left Side View

1. Front Turn Signal

2. Headlamp

3. Air Filter

4. Spark Plugs

5. Ignition Switch

6. Battery (under side cover)

7. Taillight

8. Rear Turn Signal

9. Rear Axle Adjuster (each side)

10. Rear Brake Caliper

11. Passenger's Foot Rest

12. Evaporative Emissions Canister

(California Models)

13. Oil Filter

14. Oil Drain Plug (under engine)

15. Sidestand

16. Operator's Foot Rest

17. Gear Shift Lever

18. Front Brake Caliper

19. Front Fork

20. Horn

Right Side View

1. Passenger Seat/Cowl

2. Rear Brake Fluid Reservoir

(under cover)

3. Diagnostic Connector

4. Fuses

5. Rear Shock Access

6. Front Turn Signal

7. Front Brake Caliper

8. Rear Brake Pedal

9. Operator's Foot Rest

10. Engine Oil Fill Cap/Dipstick

11. Drive Sprocket (under cover)

12. Passenger's Foot Rest

13. Drive Belt (under guard)

14. Exhaust Mufflers

2, 3, 4, 5

Component Identification

Chassis: B = CROSS ROADS CUSTOM D = CROSS COUNTRY E = CROSS ROADS G = VEGAS H = HAMMER M= JUDGE R = BOARDWALK S = VISION W= HIGH-BALL X = JACKPOT

*5VPHB26N0B3000000*

Type: A = 8-BALL B = Standard C= Custom D= Touring S = Sport W= ABS Z = Limited Edition L = Low

Series: N = North America E = International

Serial Number

Plant Code

Model Year B = 2011

SAE-assigned World Manufacturing Identifier

Check Digit

Engine HP 6 = 78-94 7 = 95-115

Engine Size 1 = 1507cc 2 = 1634cc 3 = 1731cc

Vehicle Identification Number

The vehicle identification number (VIN) is stamped into the front of the steering head and also appears on the certification label. Record the number in the space provided on page 100. You will need this identification number to title, register, license or insure the motorcycle, or to order replacement parts.

Component Identification

Engine Identification Number

The engine identification number is stamped into the right crankcase half behind the rear cylinder. The first 8 digits are the engine model number. The last 5 digits are the serial number. vided on page 100.

Ignition Key Number

The ignition key identification number is stamped into the shaft of each key. Record the number in the space provided on page 100.

Ignition Switch

The ignition switch provides electrical power to the ignition, the lighting system and all electrical switches and buttons. The ignition key operates the ignition switch and parking lights.

OFF

All electrical circuits are inactive and the ignition key can be removed.

All electrical circuits are energized and the ignition key cannot be removed. The headlamp, taillight, and instrument lights illuminate.

PARK ( P )

The taillight, indicator lights, and license plate light illuminate. The emergency flashers can be activated, and the ignition key can be removed. Push the ignition key inward while selecting the PARK position.

Record the number in the space pro-

Engine Identification Number

Park

Off

Instruments, Features and Controls

Speedometer

Indicator

Lamps

Multi-Function

Display

Instrument Cluster

Speedometer

The speedometer displays vehicle speed in either miles per hour (MPH) or kilometers per hour (km/h).

Indicator Lamps

Lamp Indicates Condition

Neutral This lamp illuminates when the transmission is in neutral and the

High Beam This lamp illuminates when the headlamp switch is set to high beam.

ignition key is in the ON position.

Turn Signal The turn signal indicator flashes when the left, right, or both turn sig-

Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of

Check Engine This lamp illuminates momentarily when the ignition switch is in the

Cruise Control Engaged (if equipped)

Not used

nals (hazard) are active. If a bulb fails, or if there is a short circuit in

the signal system, the lamp flashes at more than twice the normal rate.

fuel remains in the fuel tank.

ON position and the engine is off. This indicates proper function. If

this lamp illuminates while the engine is running, contact an authorized VICTORY dealer promptly for diagnosis. The light will

remain on if the tilt sensor shuts down the engine. See page 45. If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists. Retrieve the error codes for diagnosis. See page 27. This lamp is also known as a malfunction indicator lamp (MIL).

Instruments, Features and Controls

Instrument Cluster

Multi-Function Display

Use the mode button to toggle through the modes of the multi-function display. Press and hold the mode button to reset the trip odometers, average fuel economy, average speed and trip hour meter.

Modes Available

Standard Modes Accessory Modes

Odometer Trip Odometer 2

Trip Odometer 1 Average Fuel Economy

Tachometer Instantaneous Fuel Economy

Gear Indicator Trip Hours

Clock Average Speed

DC Voltage

Ambient Air Temperature

Display Units (Standard/Metric)

The display can be changed to display either standard or metric units of measurement.

Tip: To exit the set-up mode at any time, wait 10 seconds.The display automatically exits and returns to

the odometer display.

Standard Display Metric Display Distance Miles Kilometers Fuel U.S. Gallons Liters, Imperial Gallons Tem per atur e Fahrenheit Celsius Time 12-Hour Clock 24-Hour Clock

1. Turn the key to the OFF position.

2. Press and hold the mode button while turning the key to the ON position.

3. When the display flashes the distance setting, tap the mode button to advance to the desired setting.

4. Press and hold the mode button to save the setting and advance to the next display option.

5. Repeat the procedure to change remaining display settings.

Instruments, Features and Controls

Instrument Cluster

Multi-Function Display

Odometer

The odometer displays total distance traveled by the vehicle.

Trip Odometers

The ignition switch must be in the ON position to access the trip odometers. The trip odometers (Trip 1 and Trip 2) display total distance traveled since being reset. To reset a trip odometer, toggle to the trip odometer. Press and hold the mode button until the meter resets.

Engine Speed (Tachometer)

Engine speed displays in revolutions per minute (RPM).

Gear Position

A gear position displays only when the transmission is in gear and the motorcycle is moving. Two dashes (--) display if the stop/run switch is in the RUN position and the motorcycle is

not moving while in gear. The dashes also display if the stop/run switch is in the STOP position.

“N” displays when the stop/run switch is in the RUN position and the transmission is in neutral.

Clock

Tip: The clock must be reset any time the battery has been disconnected or discharged.

1. Turn the key to the ON position. Use the mode button to toggle to the odometer display.

2. Press and hold the mode button until the hour segment flashes. Release the button.

3. With the segment flashing, tap the mode button to advance to the desired setting.

4. Press and hold the mode button until the next segment flashes. Release the button.

5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the 1-minute segment, step 4 will save the new settings and exit the clock mode.

6. Turn the key to the OFF position.

Average Fuel Economy (Accessory)

This mode displays average fuel economy since being reset. To reset, toggle to this mode. Press and hold the mode button until the meter resets.

Instantaneous Fuel Economy (Accessory)

This mode displays the instantaneous fuel economy of the motorcycle.

Trip Hours Meter (Accessory)

The trip hours meter displays total hours of operation since being reset. To reset, toggle to this mode. Press and hold the mode button until the meter resets.

Instruments, Features and Controls

Instrument Cluster

Multi-Function Display

Average Speed (Accessory)

The average speed mode displays average vehicle speed since being reset. To reset, toggle to this mode. Press and hold the mode button until the meter resets.

DC Voltage (Accessory)

The volt meter displays battery voltage. If the engine is not running, approximate battery voltage displays. If the engine is running, approximate charging voltage displays.

Ambient Air Temperature (Accessory)

If the accessory sensor is installed, toggle to this mode to display the ambient air temperature. The key must be in the ON position.

Diagnostic Functionality

Certain conditions will cause an error message to display in the screen. If this occurs, please see your VICTORY dealer.

Message Location Indicates

LO DC Voltage Screen Voltage remains below 11.0 volts for more than 10 seconds OV DC Voltage Screen Voltage remains above 15.0 volts for more than 10 seconds ERROR All Checksum error (gauge malfunction)

+ 80 hidden pages