Victory Hammer S 8-Ball 2011, Vegas 8-Ball 2011, Kingpin 8-Ball 2011, Vegas Jackpot 2011 Owner's manual
PMS 419
2011 Owner's Manual
Hammer
Hammer S
Hammer 8-Ball
Vegas
Vegas 8-Ball
Kingpin
Kingpin 8-Ball
Vegas Jackpot
Ness Signature Series Vegas Jackpot
®
®
®
®
®
®
®
®
®
California Proposition 65 Warning
This product contains or emits
chemicals known to the state of
California to cause cancer and birth
defects or other reproductive harm.
The text is printed on 100% recycled
with 40% post-consumer waste (PCW).
PMS 419
For your nearest Polaris dealer,
call 1-800-POLARIS
or visit www.polarisindustries.com
Polaris Sales Inc.,
2100 Hwy. 55, Medina, MN 55340
Phone 1-888-704-5290
Part No. 9923011 Rev 01
Printed in USA
*9923011 *
2011 Owner’s Manual
Hammer
®
Hammer® S
Hammer 8-Ball
Vegas
Vegas 8-Ba ll
Kingpin
Kingpin 8-Ball
Vegas Jackpot
®
®
®
®
®
®
Ness Signature Series V egas Jackpot
®
1
Copyright© 2010 Polaris Sales Inc.
All material in this publication is based on the latest product information at the time of publication. Due to con-
stant improvements in the design and quality of production components, some minor discrepancies may result
between the actual vehicle and the information presented in this publication. Depictions and/or procedures in this
publication are intended for reference use only. No liability can be ac cepted for omissions or inaccu racies. Polaris
Industries reserves the right to make changes at any time, without notice and without incurring obligation to make
the same or similar changes to previously manufactured vehicles. Any reprinting, reuse or redistribution of the
material in this document is expressly prohibited.
Features of VICTORY Motorcycles are covered by U.S. Patents: 6,976,691; 6,407,663; D489670; D482311;
D482304; D481980; D481973; D474142. Refer also to the patent label on the motorcycle.
The following are registered trademarks of Polaris Industries Inc.:
POLARIS, THE WAY OUT, FREEDOM, HAMMER, HAMMER 8-BALL, VEGAS, VEGAS JACKPOT,
VEGAS 8-BALL, KINGPIN, KINGPIN 8-BALL, VICTORY and VICTORY MOTORCYCLES.
DUNLOP is a registered trademark of Dunlop Tire Corporation.
Printed in U.S.A.
P/N 9923011
2
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Reporting Safety Defects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Instruments, Features and Controls. . . . . . . . . . . . . . . . . . . . . . 19
Pre-Ride Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Identification Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Maintenance Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
3
Introduction
Thank you for purchasing a Polaris vehicle, and welcome to our world-wide family of
Polaris owners. We proudly produce an exciting line of utility and recreational products.
• Snowmobiles
• All-terrain vehicles (ATVs)
• RANGER
• Low emission vehicles (LEVs)
• Victory Motorcycles
For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and
recommendations in this owner’s manual. Keep this manual with the motorcycle, especially
when ownership changes. If your owner’s manual is misplaced or damaged, please purchase
a replacement from your VICTORY dealer.
All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operator’s
perspective when seated in a normal riding position. If you have questions about the operation or maintenance of your motorcycle after you've read this manual, please see your VICTORY dealer. To locate the nearest authorized VICTORY dealer, call 1-800-POLARIS or
visit www.polarisindustries.com.
VICTORY motorcycles comply with all federal, state and local safety and emission regulations for the area of intended sale.
®
utility vehicles
®
4
Safety
WARNING
About the Owner's Manual
Failure to follow recommended precautions and procedures could result in severe injury or death.
Always heed all safety precautions and follow all operation, inspection and maintenance procedures
outlined in this manual.
Please read your VICTORY owner’s manual. This manual contains information essential to
safe riding and proper maintenance of the motorcycle. Anyone who rides the motorcycle
(operators and passengers) must read the owner's manual before riding.
Read and understand the information found in the safety section, and bring the manual with
you when you ride. Following the safety precautions and procedures will add to your riding
enjoyment and ensure a safe ride.
Understand and follow all inspection and maintenance procedures outlined in this manual.
Following these procedures will ensure that your motorcycle remains in safe operating condition at all times.
Safety Terms and Signal Words
The following signal words and symbols appear throughout this manual and on your vehicle.
Your safety and the safety of others is involved when these words and symbols are used.
Become familiar with their meanings before reading the manual.
The safety alert symbol indicates a potential personal injury hazard.
WARNING
A WARNING indicates a hazardous situation which, if not avoided, may result in death or serious injury.
CAUTION
A CAUTION indicates a hazardous situation which, if not avoided, may result in minor or moderate
injury.
NOTICE
A NOTICE indicates a situation that may result in property damage.
5
Safety
WARNING
Safe Riding Practices
Improper use of this motorcycle can result in serious injury or death to you, your passenger and others.
To minimize the risk of injury, read and understand the information contained in this section before
operating the motorcycle. Anyone who rides the motorcycle (operators and passengers) must follow
these safety precautions.
Motorcycling has inherent risks.
You can minimize those risks, but you can't eliminate them completely. Even if you're an
experienced motorcycle operator or passenger, read all of the information in this safety section before operating the motorcycle.
• T ake a rider education course from the Motorcycle Safety Foundation or another qualified
instructor. The course will help you develop or refresh your expertise in safe riding habits
through instruction and riding. For information on Motorcycle Safety Foundation rider
education courses in your area, call 1-800-446-9227 or visit their web site at www.msfusa.org.
• Read and understand all information in this owner's manual.
• Observe all maintenance requirements specified in this manual. For assistance, see the
VICTORY Service Manual or your authorized VICTORY dealer.
Design characteristics affect how you should ride the VICTORY motorcycle.
• The motorcycle is designed for on-road use with one rider and one passenger. See page 9.
• Do not exceed the gross vehicle weight rating (GVWR). See the specifications section
beginning on page 82 or the certification label on the steering head. Riding off-road, riding
with more than one passenger, or carrying weight exceeding the maximum weight rating
can make handling difficult, which could cause loss of control.
• Be prepared to reduce speed to maintain stability if your motorcycle is equipped with features such as saddlebags, a windshield or a passenger backrest.
6
Safety
Safe Riding Practices
Follow these general safe riding practices:
• Before each ride, perform the pre-ride inspections. See page 26.
• Follow all break-in procedures during the first 500 miles (800 km) of operation. See page
35.
• Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding
where there is little or no traffic. Practice riding at a moderate speed on various road surfaces and in different weather conditions.
• Know your skills and limits, and ride within them.
• Allow only licensed, experienced operators to ride your motorcycle, and then only after
they have become familiar with its controls and operation. Make sure all riders read and
understand this owner’s manual before riding.
• Do not ride when you're fatigued or under the influence of alcohol, prescription drugs,
over-the-counter drugs or any other drugs.
• If your motorcycle operates abnormally, correct the problem immediately. See the VIC-
TORY Service Manual or your authorized VICTORY dealer. Continued operation could
aggravate the initial problem, increase the cost of repairs and threaten your safety.
• Ride defensively, as if you are invisible to other motorists, even in broad daylight. A
motorist's failure to see or recognize a motorcycle is the leading cause of automobile/
motorcycle accidents. Ride where you're clearly visible to other motorists, and observe
their behavior carefully.
• Be especially cautious at intersections, as these are the most likely places for an accident.
• To prevent loss of control, keep your hands on the handlebars and your feet on the foot-
rests.
• Do not move or operate the motorcycle with the steering locked (if equipped), as the
severely restricted steering could result in loss of control.
• Obey the speed limit and adjust your speed and riding technique based on road, weather
and traffic conditions. As you travel faster, the influence of all other conditions increases,
which can affect the motorcycle's stability and increase the possibility of losing control.
7
Safety
Safe Riding Practices
• Reduce speed when:
- the road has potholes or is otherwise rough or uneven.
- the road contains sand, dirt, gravel or other loose substances.
- the road is wet, icy or oily.
- the road contains painted surfaces, manhole covers, metal grating, railway cr ossings or
other slippery surfaces.
- weather is windy, rainy or otherwise causing slippery or rapidly changing conditions.
- traffic is heavy, congested, not allowing sufficient space between vehicles or otherwise
not flowing smoothly.
- being passed in either direction by a lar ge vehicle that produces a wind blast in its wake.
• T o maximize braking ef fectiveness, use the front and re ar brak es together. Be aware of t he
following important information:
- The rear brake provides 40% of the motorcycle's stopping power, at most.
- To avoid skidding, app ly the brakes gradually when the r oad is wet o r r ough, or con tains
loose or other slippery substances.
- If possible, avoid applying the brakes while making a turn. Motorcycle tires have less
traction during turns, so braking will increase the possibility of skidding. Bring the
motorcycle to the upright position before applying the brakes.
• To avoid loss of control:
- Retract the sidestand fully before riding. Ground clearance is reduced when the motor-
cycle leans.
- When approaching a curve, choose a speed and lean angle that will allow you to pass
through the curve in your own lane without applying the brakes.
- Do not allow components to contact the road surface when leaning in a curve.
- Do not tow a trailer, which can make the motorcycle hard to handle.
8
Safety
Safe Riding Practices
Carrying a Passenger
Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests.
To carry a passenger safely:
• Do not exceed the gross vehicle weight rating (GVWR).
• If necessary, adjust the rear shock preload. See page 50. Improper preload adjustment can
make your motorcycle hard to handle and can cause loss of control.
• Before riding, be sure your passenger is familiar with safe riding procedures. An inexperi-
enced passenger may distract you or make movements that cause instability.
• Direct the passenger to hold onto you or the seat strap with both hands and to keep both
feet on the passenger footrests. Do not carry a passenger who cannot place both feet firmly
on the passenger footrests. A passenger who rides improperly can shift body weight erratically and cause instability.
• Adjust your riding style to compensate for the differences in handling, acceleration and
braking caused by the additional weight of the passenger.
Protective Apparel
Wear protective apparel to decrease the risk of injury and increase riding comfort.
• Always wear a helmet that meets or exceeds established safety standards. Approved hel-
mets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Laws
in some areas require that you wear an approved helmet. Head injuries are the leading
cause of fatalities in accidents involving motorcycles. Statistics prove that an approved
helmet is the most effective protection in preventing or reducing head injuries.
• Wear eye protection to protect eyes from wind or airborne particles and objects. Laws in
some areas require that you wear eye protection. VI CTORY recommends that you wear
approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8,
Z87.1, or CE. Make sure protective eyewear is kept clean.
• All riders should wear bright or light-colored and/or reflectiv e clo thin g to impro ve visib il-
ity to other motorists. A motorist's failure to see or recognize a motorcycle is the leading
cause of automobile/motorcycle accidents.
• Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from abra-
sions, lacerations or burns should the motorcycle fall. Wear boots with low heels, as high
heels can catch on pedals or footrests. The combination of boots and pants should completely cover legs, ankles and feet, protecting skin from engine and exhaust system heat.
• Do not wear loose, flowing clothing or long boot laces, as they can catch on handlebars,
levers or footrests, or they can become entangled in the wheels, causing loss of control and
serious injury .
9
Safety
Gross Vehicle Weight Rating (GVWR)
WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and
handling and could cause loss of control. NEVER exceed the GVWR of your motorcycle.
The maximum load capacity of your motorcycle is the maximum weight you may add to
your motorcycle without exceeding the GVWR. This capacity is determined by calculating
the difference between your motorcycle’s GVWR and wet weight.
Refer to the specification section of this manual or the Manufacturing Information/VIN label
on the motorcycle frame for model-specific information. Refer to the “Safety and Information Labels” section in this manual for location on the motorcycle.
When determining the weight you will be adding to your motorcycle, and to ensure you do
not exceed the maximum load capacity, include the following:
• operator body weight
• passenger body weight
• weight of all riders’ apparel and items in or on apparel
• weight of any accessories and their contents
• weight of any additional cargo on the motorcycle
Carrying Cargo
Use the following guidelines when attaching cargo or accessories to the motorcycle.
To prevent instability and loss of control:
• Keep cargo and accessory weight to a minimum. Keep items as close to the motorcycle as
possible to minimize a change in the motorcycle's center of gravity.
• Distribute weight evenly on both sides of the motorcycle and secure cargo to prevent
unexpected shifting. Check all accessories and cargo for security and even distribution
before riding and at each riding break.
• Do not attach large or heavy cargo such as sleeping bags, duffel bags or tents to the handlebars, front fork area or front fender. These areas are not designed to carry cargo. Cargo
in these areas can also block air flow to the engine and cause overheating.
• Do not exceed the maximum cargo weight limit of any accessory. Refer to the accessory
instructions and labels. Do not attach cargo to an accessory not designed for that purpose.
• Do not attach anything to the highway bar except highway footrests.
10
Safety
Carrying Cargo
Saddlebags
When operating a motorcycle equipped with saddlebags:
• Never ride at speeds exceeding 80 MPH (120 km/h). Depending on load and weather con-
ditions, the maximum safe operating speed may be less. Saddlebags, combined with the
lifting or buffeting effects of wind, can cause instability.
• Distribute weight evenly in each of the saddlebags.
• Do not exceed the maximum cargo capacity of the saddlebags.
• Do not exceed the gross vehicle weight rating (GVWR).
Parking the Motorcycle
When leaving the motorcycle unattended, turn the engine off and remove the ignition key.
Park the motorcycle where people are not likely to touch the hot engine or exhaust system or
place combustible materials near these hot areas. Do not park near a flammable source such
as a kerosene heater or an open flame, where hot components could ignite combustible materials.
Park the motorcycle on a firm, level surface. Sloped or soft surfaces may not support the
motorcycle. See page 40.
Modifications
Modifying the motorcycle by removing any equipment or by addi ng equipment not approved
by VICTOR Y may void your warranty . Such modifications may make the motorcycle unsafe
to ride and could result in severe injury to operator or passengers, as well as damage to the
motorcycle. Some modifications may not be legal in your area of operation. If in doubt, contact your authorized VICTORY dealer.
11
Safety
Slide turn signal
upward.
Restrain with 2 straps
on each side.
VEGAS
(Models differ in appearance, but
locations are the same as shown)
Transporting the Motorcycle
When transporting the motorcycle:
• Use a truck or trailer. Never tow the motorcycle. Towing will impair steering and handling.
• Restrain the motorcycle in an upright position to prevent fuel leaks.
• Place the transmission in neutral.
• Do not place restraints on the handlebars. Loosen the front turn signal mounts and slide
them upward. Place tiedown straps around the fork tubes above the lower triple clamp.
Secure the rear of the motorcycle with tiedowns around both sides of the swingarm, being
careful to avoid the brake line, exhaust and drive belt. Reposition the turn signals before
operating the motorcycle.
12
Safety
WARNING
Accessory Selection and Installation
Use the following guidelines when choosing and installing accessories:
• Do not install accessories that impair the stability , handling or operation of the motorcycle.
Before installing an accessory, be sure that it does not:
- Reduce ground clearance when the motorcycle is either leaning or upright.
- Limit suspension or steering travel or your ability to operate contr ols.
- Displace you from your normal riding position.
- Obscure lights or reflectors.
• Do not install bulky or large accessories that can cause instability (due to the lifting or buf-
feting effects of wind).
• Do not install electrical accessories that exceed the capacity of the electrical system.
Never install higher wattage light bulbs than those supplied as original equipment. An
electrical failure could result and cause hazardous loss of engine power or lights, or damage to the electrical system.
• Always install accessories designed and approved by VICTORY specifically for your
model, especially a windshield, backrest or luggage rack. An improperly designed or
installed accessories can reduce stability, causing loss of control. Follow the instructions
for proper installation and use.
Fuel and Exhaust Safety
Gasoline is highly flammable and explosive under certain conditions.
• Always exercise extreme caution whenever handling gasoline.
• Always turn off the engine before refueling.
• Always refuel outdoors or in a well-ventilated area.
• Open the fuel cap slowly. Do not overfill the tank. Do not fill the tank neck.
• Do not smoke or allow open flames or sparks in or near the area where refueling is performed or
where gasoline is stored.
Gasoline and gasoline vapors are poisonous and can cause severe injury.
• Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you swallow gasoline, inhale
more than a few breaths of gasoline vapor, or get gasoline in your eyes, see a physician
immediately.
• If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change
clothing.
• If gasoline spills on the any part of the motorcycle, immediately rinse it off with water.
Exhaust gases contain carbon monoxide, a colorless, odorless gas that can cause loss of
consciousness or death in a short time.
• Never start the engine or let it run in an enclosed area.
• Never inhale exhaust gases.
13
Safety
WARNING
Safety Maintenance
Failure to perform safety maintenance as recommended can result in difficult handling and loss of
control, which could result in serious injury or death. Always perform the safety maintenance
procedures as recommended. Perform maintenance and repairs promptly as outlined in the VICTORY
Service Manual, or see your authorized VICTORY dea l er fo r servic e .
• Before each ride, perform the pre-ride inspections. See page 26.
• Perform maintenance at the intervals specified in the periodic maintenance table. See page
42.
• Always maintain proper tire pressure, tread condition and wheel and tire balance. Inspect
tires regularly and replace worn or damaged tires promptly. Use only approved replacement tires.
• Always ensure proper steering head bearing adjustment.
• Regularly inspect the rear shock absorber and the front forks for fluid leaks or damage.
Make any necessary repairs promptly.
• Clean the motorcycle thoroughly to reveal items in need of repair. See page 69.
• Make sure all legally required equipment is properly installed and in good condition,
including the license plate.
• Fasteners must meet original specifications for quality, finish and type to ensure safety.
Use only genuine VICTORY replacement parts, and ensure that all fasteners are tightened
to the proper torque.
Electromagnetic Interference
This vehicle complies with European directive 97/24/EC Chapter 8 requirements, which is
equivalent to Canadian ICES-002.
Reporting Safety Defects
If you believe that your vehicle has a defect that could result in a crash or cause injury or
death, you should immediately inform the National Highway Traffic Safety Administration
(NHTSA) in addition to notifying Polaris Industries in writing.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a
safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or
Polaris Industries.
T o co ntact NHTS A, or obtain other information about motor vehicle safety, you may call the
Vehicle Safety Hotline toll free at 1-888-327-4236 (TTY: 1-800-424-9153), visit the NHTSA
web site at www.safercar.gov, or write to:
ADMINISTRATOR, NHTSA
1200 New Jersey Avenue, SE
West Building
Washington, DC 20590
14
Safety and Information Labels
Warning
Label
Manufacturing
Information
Label (VIN)
Engine Identification Number
(stamped on right rear
crankcase half)
Emission Control,
Noise Information
Label
Tire Warning Label
(if applicable)
Patent
Notice
Tire Warning
Label
(if applicable)
Fuse and Relay Label
(under side cover, on side of fuse box cover)
Fuse Box Removal Instruction Label
(on base of fuse box)
Due to different model and market requirements, your vehicle may not have all of the labels
shown. Labels that apply to your model will be located as shown.
Safety
15
Component Identification
3
5
1
9
11
4
10
9
7
8
2
6
(Models differ in appearance, but
locations are the same as shown)
6
3
1
19
2
4
5
7
13
8
9
10
11
12
14
16
15
20
17
18
13
1
6
8
7
12
10
9
2, 3, 4, 5
11
14
Handlebar Area
1. Clutch Lever
2. Mirror
3. Speedometer
4. Indicator Light Panel
5. Tachometer (if equipped)
6. Front Brake Fluid Reservoir
7. Front Brake Lever
8. Throttle Control Grip
9. Switches
10. Throttle Cables
11. Fuel Cap
Left Side View
1. Front Turn Signal
2. Headlamp
3. Air Filter
4. Spark Plugs
5. Ignition Switch
6. Battery (under side cover)
7. Taillight
8. Rear Turn Signal
9. Rear Axle Adjuster (each side)
10. Rear Brake Caliper
11. Passenger's Foot Rest
12. Evaporative Emissions Canister
(California Models)
13. Oil Filter
14. Oil Drain Plug (under engine)
15. Sidestand
16. Operator's Foot Rest
17. Gear Shift Lever
18. Front Brake Caliper
19. Front Fork
20. Horn
Right Side View
1. Passenger Seat/Cowl
2. Rear Brake Fluid Reservoir
(under cover)
3. Diagnostic Connector
4. Fuses
5. Rear Shock Access
6. Front Turn Signal
7. Front Brake Caliper
8. Rear Brake Pedal
9. Operator's Foot Rest
10. Engine Oil Fill Cap/Dipstick
11. Drive Sprocket (under cover)
12. Passenger's Foot Rest
13. Drive Belt (under guard)
14. Exhaust Mufflers
16
Component Identification
Chassis:
B = CROSS ROADS CUSTOM
C= KINGPIN
D= CROSS COUNTRY
E = CROSS ROADS
G= VEGAS
H= HAMMER
S = VISION
X = JACKPOT
*5VPHB26N0B3000000*
Type:
A = 8-BALL
B = Standard
C= Custom
D= Touring
S = Sport
W= ABS
Z = Limited Edition
L = Low
Series:
N= North America
E = International
Serial Number
Plant Code
Model Year
B = 2011
SAE-assigned World
Manufacturing
Identifier
Check Digit
Engine HP
6 = 78-94
7 = 95-115
Engine Size
1 = 1507cc
2 = 1634cc
3 = 1731cc
Vehicle Identification Number
The vehicle identification number (VIN) is stamped into the front of the steering head and
also appears on the certification label. Record the number in the space provided on page 88.
You will need this identification number to title, register, license or insure the motorcycle, or
to order replacement parts.
17
Component Identification
Engine Identification Number
Off
On
Park
Engine Identification Number
The engine identification number is stamped
into the right crankcase half behind the rear
cylinder. The first 8 digits are the engine
model number. The last 5 digits are the serial
number.
vided on page 88.
Ignition Key Number
The ignition key identification number is
stamped into the shaft of each key. Record the
number in the space provided on page 88.
Ignition Switch
The ignition switch provides electrical power to the ignition, the lighting system and all electrical switches and buttons. The ignition key operates the ignition switch and parking lights.
OFF
All electrical circuits are inactive and the
ignition key can be removed.
ON
All electrical circuits are energized and the
ignition key cannot be removed. The headlamp, taillight, and instrument lights illuminate.
PARK (P)
The taillight, indicator lights, and license
plate light illuminate. The emergency
flashers can be activated, and the ignition
key can be removed. Push the ignition key
inward while selecting the PARK position.
Record the number in the space pro-
18
Instruments, Features and Controls
Speedometer
Indicator
Lamps
Multi-Function
Display
Instrument Cluster
Speedometer
The speedometer displays vehicle
speed in either miles per hour (MPH) or
kilometers per hour (km/h).
Indicator Lamps
Lamp Indicates Condition
Neutral This lamp illuminates when the transmission is in neutral and the
High Beam This lamp illuminates when the headlamp switch is set to high beam.
ignition key is in the ON position.
Turn Signal The turn signal indicator flashes when the left, right, or both turn sig-
Low Oil Pressure This lamp illuminates when the ignition switch is in the ON position
Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of
Check Engine This lamp illuminates momentarily when the ignition switch is in the
Cruise Control Engaged (if equipped)
nals (hazard) are active. If a bulb fails, or if there is a short circuit in
the signal system, the lamp flashes at more than twice the normal
rate.
and the engine is off, indicating that the indicator circuit is functioning
properly. This lamp also illuminates if engine oil pressure drops
below safe operating pressure. If this lamp illuminates while the
engine is running, turn the engine off as soon as safely possible and
check the oil level. If the oil level is correct and the lamp remains on
after the engine is restarted, turn the engine off immediately.
fuel remains in the fuel tank.
ON position and the engine is off. This indicates proper function. If
this lamp illuminates while the engine is running, contact an
authorized VICTORY dealer promptly for diagnosis. The light will
remain on if the tilt sensor shuts down the engine. See page 37. If
abnormal sensor or engine operation is detected the light will remain
on as long as the fault condition exists. Retrieve the error codes for
diagnosis. See page 22. This lamp is also known as a malfunction
indicator lamp (MIL).
19
Instruments, Features and Controls
Instrument Cluster
Multi-Function Display
Use the mode button to toggle through the
modes of the multi-function display . Press and
hold the mode button to reset the trip odometers, average fuel economy, average speed and
trip hour meter.
Modes Available
Standard Modes Accessory Modes
Odometer Trip Odometer 2
Trip Odometer 1 Average Fuel Economy
Tachometer Instantaneous Fuel Economy
Gear Indicator Trip Hours
Clock Average Speed
DC Voltage
Ambient Air Temperature
Display Units (Standard/Metric)
The display can be changed to display either standard or metric units of measurement.
Tip: To exit the set-up mode at any time, wait 10 seconds.The display automatically exits and returns to
the odometer display.
Standard Display Metric Display
Distance Miles Kilometers
Fuel U.S. Gallons Liters, Imperial Gallons
Temperature Fahrenheit Celsius
Time 12-Hour Clock 24-Hour Clock
1. Turn the key to the OFF position.
2. Press and hold the mode button while turning the key to the ON position.
3. When the display flashes the distance setting, tap the mode button to advance to the
desired setting.
4. Press and hold the mode button to save the setting and advance to the next display
option.
5. Repeat the procedure to change remaining display settings.
20
Instruments, Features and Controls
Instrument Cluster
Multi-Function Display
Odometer
The odometer displays total distance traveled by the vehicle.
Trip Odometers
The ignition switch must be in the ON position to access the trip odometers. The trip odometers (Trip 1 and Trip 2) display total distance traveled since being reset. To reset a trip odometer, toggle to the trip odometer. Press and hold the mode button until the meter resets.
Engine Speed (Tachometer)
Engine speed displays in revolutions per minute (RPM).
Gear Position
A gear position displays only when the transmission is in gear and the motorcycle is moving.
Two dashes (--) display if the stop/run switch is in the RUN position and the motorcycle is
not moving while in gear. The dashes also displa y if the stop/run switch is in the STOP position.
“N” displays when the stop/run switch is in the RUN position and the transmission is in neutral.
Clock
Tip: The clock must be reset any time the battery has been disconnected or discharged.
1. Turn the key to the ON position. Use the mode button to toggle to the odometer display.
2. Press and hold the mode button until the hour segment flashes. Release the button.
3. With the segment flashing, tap the mode button to advance to the desired setting.
4. Press and hold the mode button until the next segment flashes. Release the button.
5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the
1-minute segment, step 4 will save the new settings and exit the clock mode.
6. Turn the key to the OFF position.
Average Fuel Economy (Accessory)
This mode displays average fuel economy since being reset. To reset, toggle to this mode.
Press and hold the mode button until the meter resets.
Instantaneous Fuel Economy (Accessory)
This mode displays the instantaneous fuel economy of the motorcycle.
Trip Hours Meter (Accessory)
The trip hours meter displays total hours of operation since being reset. To reset, toggle to
this mode. Press and hold the mode button until the meter resets.
21
Instruments, Features and Controls
Suspect Parameter
Number (SPN)
Error Code
Number (0-9)
Failure Mode Indicator (FMI)
Instrument Cluster
Multi-Function Display
Average Speed (Accessory)
The average speed mode displays average vehicle speed since being reset. To reset, toggle to
this mode. Press and hold the mode button until the meter resets.
DC Voltage (Accessory)
The volt meter displays battery voltage. If the engine is not running, approximate battery
voltage displays. If the engine is running, approximate charging voltage displays.
Ambient Air Temperature (Accessory)
If the accessory sensor is installed, toggle to this mode to display the ambient air temperature. The key must be in the ON position.
Diagnostic Functionality
Certain conditions will cause an error message to display in the screen. If this occurs, please
see your VICTORY dealer.
Message Location Indicates
LO DC Voltage Screen Voltage remains below 11.0 volts for more than 10 seconds
OV DC Voltage Screen Voltage remains above 15.0 volts for more than 10 seconds
ERROR All Checksum error (gauge malfunction)
Engine Error Codes
The error screen displays only when the
CHECK ENGINE light is on or when it goes
on and off during one ignition cycle. Error
codes are not stored. When the key is turned
OFF, the code and message is lost, but will
reappear if the fault reoccurs after restarting
the engine.
If the CHECK ENGINE indicator lamp illuminates, retrieve the error codes from the
display.
1. If the error codes are not displayed, use
the mode button to toggle until “Ck
ENG” displays on the main line of the
display.
2. Press and hold the mode button to enter the diagnostics code menu.
3. Record the three numbers displayed in the gear position, clock and odometer displays.
4. Press and release the mode button to advance to the next error code.
5. Press and hold the mode button to exit the diagnostics code menu.
6. See an authorized VICTORY dealer for code details and diagnosis.
22
Instruments, Features and Controls
Flasher
Switch
High/Low Light Switch
Horn Button
Turn Signal Switch
Clutch Lever
Mode Button
Left Handlebar Controls
Clutch Lever
Pull the lever toward the handlebar
to disengage the clutch. Gradually
release the lever to engage the
clutch. For smooth clutch operation,
pull the lever quickly and release it
gradually.
Tip: A clutch interlock switch prevents
the engine from starting when the
transmission is in gear and the
clutch is engaged. See page 37.
Mode Button
The mode button is located on the front side of the
left handlebar switch. Use the mode button to toggle
through the modes of the multi-function display.
See page 20. Use the mode button to set the display
units to either standard or metric units of measurement.
Emergency Flasher Switch (Hazard Switch)
Press the top of the switch to activate the emergency flashers. All turn signals will
flash. Press the bottom of the switch to cancel the flashers.
High Beam/Low Beam Light Switch
Press the upper portion of the switch to activate the high beam. Press the lower portion of the switch to activate the low beam. Press and hold the lower portion of the
switch to activate the momentary passing beam.
Horn Button
To sound the horn, press the horn button.
Turn Signal Switch
Move the turn signal switch to the left to activate the left turn signals. Move the
switch to the right to activate the right turn signals. A signal ends when speed or distance reach preset levels. To end a signal manually, move the switch to the center
and push it inward.
Momentary Feature: Move the turn signal switch left or right and hold it in that position. The signal flashes until the switch is released.
23
Instruments, Features and Controls
Stop/Run Switch
Starter Button
Throttle Control Grip
Front Brake Lever
Rear Brake Pedal
Gear Shift Pedal
Right Handlebar Controls
Engine Stop/Run Switch
Press the top of the engine stop/run switch (STOP) to stop the engine. Press the bottom of the switch (RUN) to allow operation of the engine. The engine should not
start or run when the switch is in the STOP position.
Starter Button
Press the right side of the button to start the engine. See page 37. The starter button
works only when the stop/run switch is on RUN and the transmission is in neutral or
the clutch is disengaged (lever pulled in toward handlebar.)
Throttle Control Grip
Twist the throttle control grip toward your body to increase engine speed. Twist the grip
away from your body to decrease engine speed. When you release the grip, it returns to the
idle speed position.
Front Brake Lever
Pull the lever toward the handlebar to apply the front brake. Always follow proper braking
procedures. See page 39. To maximize braking effectiveness, use the front and rear brakes
together.
Gear Shift Pedal
To shift to a lower gear, press down on the gear shift pedal.
To shift to a higher gear, lift up on the gear shift pedal. See
page 37.
Rear Brake Pedal
To apply the rear brake, press down on the rear brake pedal.
Always follow proper braking procedures. See page 39. To
maximize braking effectiveness, use the front and rear
brakes together.
24
Instruments, Features and Controls
Fuel Cap
Key Slot Cover
Grommets
Fuel Cap
Use the ignition key to open and close the fuel cap. Follow
proper fueling procedures. See page 36.
Tip: Prime the fuel pump if the tank is completely empty.
Open the fuel cap
1. Lift the key slot cover on the fuel cap and insert the key.
2. Turn the key clockwise while pushing downward
lightly. The latch will release and allow you to open the
cap.
Close the fuel cap
1. Insert the key into the cap. Turn the key clockwise and press downward on the cap.
2. Turn the key counter-clockwise while pushing downward lightly.
3. Remove the key and close the key slot cover.
Sidestand
WARNING! An improperly retracted sidestand could contact the ground during operation and cause
loss of control resulting in serious injury or death. Always make sure the sidestand is fully retracted
before operating the motorcycle.
1. While the motorcycle is in the upright position, push the sidestand downward until it is
fully extended.
2. Slowly lean the motorcycle to the left until the full weight of the motorcycle rests safely
on the sidestand.
3. To retract the sidestand, bring the motorcycle to the upright position. Swing the
sidestand upward to its fully retracted position.
Side Covers
Remove the left side cover to access the battery. Remove the right side cover to access
the fuses and the rear brake fluid reservoir.
1. Pull outward at each corner of the side
cover to disengage the darts.
2. Remove the side cover.
3. To reinstall the side cover, make sure
each rubber grommet is properly located.
Align each dart with the appropriate
grommet and press inward firmly to
secure.
25
Pre-Ride Inspections
WARNING
Always perform the recommended pre-ride inspections before each ride. Always perform the
inspections before making a long trip and when removing the motorcycle from storage.
Failure to perform the recommended pre-ride inspections could result in component failure while riding,
which could result in serious injury or death. Always perform the pre-ride inspections before each ride.
When inspection reveals the need for adjustment, replacement or repair, perform the service promptly.
Tip: You must be familiar with all instruments and controls to perform the pre-ride inspections.
During the pre-ride inspections you may use products that are potent iall y hazardous, such as
oil or brake fluid. When using any of these products, always follow the instructions and
warnings on the product packaging.
When inspections reveal the need for adjustment, replacement or repair:
• refer to the maintenance section of this manual
• refer to the VICTORY Service Manual
• or see your authorized VICTORY dealer
Electrical Components
Move the ignition switch to the ON position before performing the electrical inspections outlined on this page. Return the ignition switch to the OFF position after completing these
inspections. If inspection of any electrical item reveals component failure, repair or replace
the component before operating the motorcycle.
Electrical Item Inspection Procedure
Headlamp Verify that the headlamp illuminates. Switch to high beam. Verify that the high
Taillight/Brake Light Verify that the taillight and license plate light illuminate. Verify that taillight
Turn Signals Move the turn signal switch to the left. Verify that front and rear left turn signals
Emergency Flashers Slide the emergency flasher switch to the left. Verify that all four turn signals
Horn Press the horn button. Verify that the horn sounds loudly.
Low Oil Pressure
Indicator
Neutral Indicator Place the transmission in neutral. Verify that the neutral indicator comes on.
Engine Stop/Run
Switch
beam indicator comes on and that lamp brightness increases.
brightness increases when the front brake lever is applied and also when the
rear brake pedal is applied.
flash, as well as the corresponding light on the indicator panel. Push the
switch inward to cancel the signal. Verify that the signals and the indicator light
stop flashing. Repeat the procedure for the right turn signals.
flash, as well as the light on the indicator panel. Slide the switch to the right.
Verify that all signals and indicators stop flashing.
Start the engine. Verify that the low oil pressure indicator goes off.
Start the engine. Move the stop/run switch to the STOP position. V erify that the
engine stops. Attempt to restart the engine to verify that the engine WILL NOT
start.
26
Loading...