Victory Hammer S 2014, Hammer 8Ball 2014, Vegas Jackpot 2014, Vegas 8Ball 2014, High Ball 2014 Owner's manual
...
2014 Rider’s Manual
Hammer® S
Hammer 8-Ball®
Vegas Jackpot®
Vegas 8-Ball®
High-Ball®
Victory Judge™
Victory Boardwalk™
1
Copyright© 2013 Polaris Sales Inc.
All material in this publication is based on the latest product information at the time of publication. Due to con-
stant improvements in the design and quality of production components, some minor discrepancies may result
between the actual vehicle and the information presented in this publication. Depictions and/or procedures in this
publication are intended for reference use only. No liability can be accepted for omissions or inaccuracies. Polaris
Industries reserves the right to make changes at any time, without notice and without incurring obligation to make
the same or similar changes to previously manufactured vehicles. Any reprinting, reuse or redistribution of the
material in this document is expressly prohibited.
Features of VICTORY Motorcycles are covered by U.S. Patents: 6,976,691; 6,407,663; D489670; D482311;
D482304; D481980; D481973; D474142. Refer also to the patent label on the motorcycle.
The following are registered trademarks of Polaris Industries Inc.: POLARIS, FREEDOM, HAMMER,
HAMMER 8-BALL, VEGAS, VEGAS JACKPOT, VEGAS 8-BALL, HIGH-BALL, VICTORY and VICTORY
MOTORCYCLES.
VICTOR Y JUDGE and VICTORY BOARDWALK are trademarks of Polaris Industries Inc.
DUNLOP is a registered trademark of Dunlop Tire Corporation.
Printed in U.S.A.
P/N 9924962
2
WARNING
Improper vehicle use can result in SEVERE INJURY or DEATH.
NEVER Operate:
• If you are under the age of 16 and without a driver’s license with motorcycle endorsement
• Under the influence of drugs or alcohol
• Off-road
• With more than one passenger (motorcycle must be equipped with passenger foot pegs)
• With weight that exceeds maximum weight rating
ALWAYS:
• Wear a helmet, eye protection, gloves, long-sleeve shirt, long pants and over-the-ankle boots.
• Make sure any passenger reads and understands all safety labels.
• Be aware of your surroundings and driving conditions.
• Keep both hands on the handlebars and both feet on the footrests when riding.
• Use only genuine VICTORY accessories designed for your model.
AL WAYS USE AN
APPROVED HELMET
AND PROTECTIVE
GEAR.
READ RIDER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND WARNINGS.
Safety Training
Safety training is a top priority for POLARIS. POLARIS strongly encourages you to take a rider
education course from the Motorcycle Safety Foundation or another qualified instructor. The course
will help you develop or refresh your expertise in safe riding habits through instruction and riding.
For information on Motorcycle Safety Foundation rider education courses in your area, call 1-800 446-9227 or visit their home page at www.msf-usa.org.
NEVER USE WITH
DRUGS OR ALCOHOL.
3
4
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Reporting Safety Defects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Instruments, Features and Controls. . . . . . . . . . . . . . . . . . . . . . 25
Pre-Ride Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Identification Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Maintenance Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
5
Introduction
Thank you for purchasing a Polaris vehicle, and welcome to our world-wide family of
Polaris owners. We proudly produce an exciting line of utility and recreational products.
• Snowmobiles
• All-terrain vehicles (ATVs)
• Low emission vehicles (LEVs)
• RANGER® utility vehicles
• VICTORY® motorcycles
• GEM® vehicles
For the safe and enjoyable operation of your vehicle, be sure to follow the instructions and
recommendations in this rider’s manual. Keep this manual with the motorcycle, especially
when ownership changes. If your rider’s manual is misplaced or damaged, please purchase a
replacement from your VICTORY dealer.
All references in this manual to RIGHT, LEFT, FRONT or REAR are from the operator’s
perspective when seated in a normal riding position. If you have questions about the operation or maintenance of your motorcycle after you've read this manual, please see your VICTORY dealer. To locate the nearest authorized VICTORY dealer, call 1-800-POLARIS or
visit www.polaris.com.
VICTORY motorcycles comply with all federal, state and local safety and emission regulations for the area of intended sale.
6
Safety
WARNING
About the Rider's Manual
Failure to follow recommended precautions and procedures could result in severe injury or death.
Always heed all safety precautions and follow all operation, inspection and maintenance procedures
outlined in this manual.
This rider’s manual contains information that is essential to safe riding and proper maintenance of your VICTORY motorcycle. Anyone who uses the motorcycle (operators and passengers) must read the rider’s manual before riding. Carefully read and understand the
information found in the Safety section. Understand and follow the procedures outlined in
the Maintenance section to keep your VICTORY motorcycle in top condition on the road or
in storage. Bring the manual with you when you ride. Following the precautions and procedures in the manual will add to your enjoyment and help keep you riding safely. If you lose
or damage this manual, you can purchase a new one through any authorized VICTORY
dealer. The rider’s manual should be considered part of the motorcycle and remain with it if
sold.
7
Safety
Safety Terms and Signal Words
The following signal words and symbols appear throughout this manual and on your vehicle.
Your safety and the safety of others is involved when these words and symbols are used.
Become familiar with their meanings before reading the manual.
The safety alert symbol indicates a potential personal injury hazard.
DANGER
A DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING
A WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION
A CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate
injury.
NOTICE
A NOTICE indicates a situation that could result in property damage.
The Prohibition Safety Sign indicates an action NOT to take in order to avoid a hazard.
The Mandatory Action Sign indicates an action that NEEDS to be taken to avoid a hazard.
8
Safety
WARNING
Safe Riding Practices
Improper use of this motorcycle can result in serious injury or death to you, your passenger and others.
To minimize the risk of injury, read and understand the information contained in this section before
operating the motorcycle. This section contains safety information specific to the VICTORY motorcycle,
as well as information about general motorcycle safety. Anyone who rides the motorcycle (operators
and passengers) must follow these safety precautions.
Motorcycling has inherent risks.
You can minimize those risks, but you can't eliminate them completely. Even if you're an
experienced motorcycle operator or passenger, read all of the safety information in this manual before operating the motorcycle.
• T ake a rider education course from the Motorcycle Safety Foundation or another qualified
instructor. The course will help you develop or refresh your expertise in safe riding habits
through instruction and riding. For information on Motorcycle Safety Foundation rider
education courses in your area, call 1-800-446-9227 or visit their web site at www.msfusa.org.
• Read and understand all information in this rider’s manual.
• Observe all maintenance requirements specified in this manual. For assistance, see the
VICTORY Service Manual or your authorized VICTORY dealer.
Design characteristics affect how you should ride the VICTORY motorcycle.
• The motorcycle is designed for on-road use with one rider and one passenger. See the
manufacturer’s label (on the left side of the frame at the steering head). The label contains
the Vehicle Identification Number (VIN) and Gross Vehicle Weight Rating (GVWR) and
Gross Axle Weight Rating (GAWR) information. Never exceed the GVWR or the GAWR.
• Riding off-road, riding with more than one passenger, or carrying weight exceeding the
maximum weight rating can make handling difficult, which could cause loss of control.
• During the first 500 miles (800 km) of operation, follow all break-in procedures as outlined in the break-in section beginning on page 45. Failure to do so can result in serious
engine damage.
• Some VICTORY motorcycles include saddlebags, a windshield, a trunk, luggage racks or
a passenger backrest as standard equipment. To maintain stability, be prepared to reduce
the operating speed of motorcycles equipped with these items.
9
Safety
Safe Riding Practices
Follow these general safe riding practices:
• Before each ride, perform the pre-ride inspections as outlined beginning on page 34.
• Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding
where there is little or no traffic. Practice riding at a moderate speed on various road surfaces and in different weather conditions.
• Know your skills and limits, and ride within them.
• Allow only licensed, experienced operators to ride your motorcycle, and then only after
they have become familiar with its controls and operation. Make sure all riders read and
understand this rider’s manual before riding.
• Do not ride when you're fatigued, ill or under the influence of alcohol, prescription drugs,
over-the-counter drugs or any other drugs. Fatigue, illness, alcohol and drugs can cause
drowsiness, loss of coordination and loss of balance. They can also affect your awareness
and judgment.
• If your motorcycle operates abnormally, correct the problem immediately. See the VIC-
TORY Service Manual or an authorized VICTORY dealer.
• Ride defensively, as if you are invisible to other motorists, even in broad daylight. A
motorist's failure to see or recognize a motorcycle is the leading cause of automobile/
motorcycle accidents . Ride where you're clearly visible to other motorists, and observe
their behavior carefully.
• Be especially cautious at intersections, as these are the most likely places for an accident.
• To prevent loss of control, keep your hands on the handlebars and your feet on the footrests.
• Be aware that the highway bar is not designed to protect the rider from injury in a collision.
• Do not move or operate the motorcycle with the steering locked (if equipped), as the
severely restricted steering could result in loss of control.
• Obey the speed limit and adjust your speed and riding technique based on road, weather
and traffic conditions. As you travel faster, the influence of all other conditions increases,
which can affect the motorcycle's stability and increase the possibility of losing control.
10
Safety
Safe Riding Practices
• Reduce speed when:
• the road has potholes, or is otherwise rough or uneven.
• the road contains sand, dirt, gravel or other loose substances.
• the road is wet, icy or oily.
• the road contains painted surfaces, manhole covers, metal grating, railway crossings or other
slippery surfaces.
• The weather is windy, rainy or otherwise causing slippery or rapidly changing conditions.
• Traffic is heavy, congested, not allowing sufficient space between vehicles or otherwise not flowing smoothly.
• You are being passed in either direction by a large vehicle that may produce a wind blast in its
wake.
• T o maximize braking effectiveness, use the fr ont and r ear brakes together. Be aware of the
following braking facts and practices:
• The rear brake provides 40% of the motorcycle's stopping power, at most. Use the front and rear
brakes together.
• T o avoid skidding, apply the brakes gradually when the road is wet or rough, or contains loose or
other slippery substances.
• If possible, avoid applying the brakes while making a turn. Motorcycle tires have less traction
during turns, so braking will increase the possibility of skidding. Bring the motorcycle to the
upright position before applying the brakes.
• When approaching a curve, choose a speed and lean angle that allows you to pass through
the curve in your own lane without applying the brakes. Excessive speed, improper lean
angle or braking in a curve can cause loss of control.
• Ground clearance is reduced when the motorcycle leans. Do not allow components to contact the road surface when leaning the motorcycle in a curve, as this could cause loss of
control.
• Retract the sidestand fully before riding. If the sidestand is not fully retracted, it could contact the road surface and cause loss of control.
• Do not tow a trailer. Towing a trailer can make the motorcycle hard to handle.
11
Safety
Safe Riding Practices
Carrying a Passenger
Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests.
To carry a passe nger safely:
• Do not exceed the gross vehicle weight rating (GVWR). See the manufacturer’s label (on
the left side of the frame at the steering head).
• If necessary , adjust the rear shock preload. See page 60. Improper preload adjustment can
make your motorcycle hard to handle and can cause loss of control.
• Before riding, be sure your passenger is familiar with safe riding procedures. An inexperienced passenger may distract you or make movements that cause instability.
• Direct the passenger to hold onto you or the seat strap with both hands and to keep both
feet on the passenger footrests. Do not carry a passenger who cannot place both feet firmly
on the passenger footrests. A passenger who rides improperly can shift body weight erratically and cause instability.
• Adjust your riding style to compensate for the differences in handling, acceleration and
braking caused by the additional weight of the passenger.
12
Safety
Safe Riding Practices
Protective Apparel
Wear protective apparel to decrease the risk of injury and increase riding comfort.
• Always wear a helmet that meets or exceeds established safety standards. Approved hel-
mets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Laws
in some areas require that you wear an approved helmet. Head injuries are the leading
cause of fatalities in accidents involving motorcycles. Statistics prove that an approved
helmet is the most effective protection in preventing or reducing head injuries.
• Wear eye protection to protect eyes from wind or airborne particles and objects. Laws in
some areas require that you wear eye protection. VICTORY recommends that you wear
approved Personal Protective Equipment (PPE) bearing markings such as VESC 8, V-8,
Z87.1, or CE. Make sure protective eyewear is kept clean.
• All riders should wear bright or light-colored and/or reflective clothing to improve visibil-
ity to other motorists. A motorist's failure to see or recognize a motorcycle is the leading
cause of automobile/motorcycle accidents.
• Wear gloves, a jacket, heavy boots and long pants to prevent or reduce injury from abra-
sions, lacerations or burns should the motorcycle fall. Wear boots with low heels, as high
heels can catch on pedals or footrests. The combination of boots and pants should completely cover legs, ankles and feet, protecting skin from engine and exhaust system heat.
• Do not wear loose, flowing clothing or long boot laces, as they can catch on handlebars,
levers or footrests, or they can become entangled in the wheels, causing loss of control and
serious injury .
13
Safety
Gross Vehicle Weight Rating (GVWR)
WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and
handling and could cause loss of control. NEVER exceed the GVWR of your motorcycle.
The maximum load capacity of your motorcycle is the maximum weight you may add to
your motorcycle without exceeding the GVWR. This capacity is determined by calculating
the difference between your motorcycle’s GVWR and wet weight.
Refer to the specification section beginning on page 96 or the Manufacturing Information/
VIN label on the motorcycle frame for model-specific information. See page 21.
When determining the weight you will be adding to your motorcycle, and to ensure you do
not exceed the maximum load capacity, include the following:
• operator body weight
• passenger body weight
• weight of all riders’ apparel and items in or on apparel
• weight of any accessories and their contents
• weight of any additional cargo on the motorcycle
Carrying Cargo
Use the following guidelines when attaching cargo or accessories to the motorcycle. Where
applicable, these guidelines also refer to the contents of any accessories.
• Keep cargo and accessory weight to a minimum, and keep items as close to the motorcycle
as possible to minimize a change in the motorcycle’s center of gravity. Changing the center of gravity can cause loss of stability and handling and could cause loss of control.
• Distribute weight evenly on both sides of the motorcycle. Maintain even weight distribution by checking accessories and cargo to make sure they’re securely attached to the
motorcycle before riding and whenever you take a break from riding. Uneven weight distribution, or accessories or cargo that shift suddenly while you’re riding can make the
motorcycle hard to handle, can cause loss of control, or cargo could fall from the motorcycle creating a hazard for surrounding vehicles.
• Do not attach large or heavy cargo such as sleeping bags, duffel bags or tents to the handlebars, front fork area or front fender. Cargo or accessories placed in these areas can
cause instability (due to improper weight distribution or aerodynamic changes) and could
cause loss of control. Such items can also block air flow to the engine and cause overheating that can damage the engine.
• Do not exceed the maximum cargo weight limit of any accessory (see accessory instructions and labels). Do not attach cargo to an accessory not designed for that purpose. Either
circumstance could result in an accessory failure that could cause loss of control.
• Do not attach anything to the motorcycle unless specifically designed for that purpose by
VICTORY.
14
Safety
Carrying Cargo
Saddlebags
When operating a motorcycle equipped with saddlebags:
• Never ride at speeds exceeding 80 MPH (120 km/h). Depending on load and weather con-
ditions, the maximum safe operating speed may be less. Saddlebags, combined with the
lifting or buffeting effects of wind, can cause instability.
• Distribute weight evenly in each of the saddlebags.
• Do not exceed the maximum cargo capacity of the saddlebags.
• Do not exceed the gross vehicle weight rating (GVWR).
Parking the Motorcycle
When leaving the motorcycle unattended, turn the engine off. Remove the ignition key to
prevent unauthorized use by minors or those without proper motorcycle certification and
training.
Park the motorcycle where people are not likely to touch the hot engine or exhaust system or
place combustible materials near these hot areas. Do not park near a flammable source such
as a kerosene heater or an open flame, where hot components could ignite combustible materials.
Park the motorcycle on a firm, level surface. Sloped or soft surfaces may not support the
motorcycle. If you must park on a slope or soft surface, follow the precautions outlined on
page 50.
Modifications
Modifying the motorcycle by removing any equipment or by adding equipment not approved
by VICTORY may void your warranty. Such modifications could make the motorcycle
unsafe to ride and could result in severe injury to operator or passengers, as well as damage
to the motorcycle. Some modifications may not be legal in your area of operation. If in
doubt, contact your authorized VICTORY dealer.
15
Safety
Slide turn signal
upward.
Restrain with 2 straps
on each side.
VEGAS
(Models differ in appearance, but
locations are the same as shown)
Transporting the Motorcycle
When transporting the motorcycle:
• Use a truck or trailer. Never tow the motorcycle. Towing will impair steering and handling.
• Restrain the motorcycle in an upright position to prevent fuel leaks.
• Place the transmission in neutral.
• Do not place restraints on the handlebars. Loosen the front turn signal mounts and slide
them upward. Place tiedown straps around the fork tubes above the lower triple clamp.
Secure the rear of the motorcycle with tiedowns around both sides of the swingarm, being
careful to avoid the brake line, exhaust and drive belt. Reposition the turn signals before
operating the motorcycle.
16
Safety
Use of Accessories
Because VICTOR Y cannot test and make specific recommendations concerning every accessory or combination of accessories sold, the operator is responsible for determining that the
motorcycle can be safely operated with any accessories or additional weight. Use the following guidelines when choosing and installing accessories:
• Do not install accessories that impair the stability, handling or operation of the motorcycle
or operator visibility. Before installing an accessory, be sure that it does not:
• Reduce ground clearance when the motorcycle is either leaned or in a vertical position.
• Limit suspension or steering travel or your ability to operate controls.
• Displace you from your normal riding position.
• Obscure lights or reflectors.
• Bulky or large accessories can cause instability (due to the lifting or buffeting effects of
wind) and loss of control.
• Do not install electrical accessories that exceed the capacity of the motorcycle’s electrical
system. Never install higher wattage light bulbs than those supplied as original equipment.
An electrical failure could result and cause hazardous loss of engine power or lights, or
damage to the electrical system.
• Use only genuine VICTORY accessories designed for your model.
17
Safety
WARNING
Fuel and Exhaust Safety
Gasoline is highly flammable and explosive under certain conditions.
• Always exercise extreme caution whenever handling gasoline.
• Always turn off the engine before refueling.
• Always refuel outdoors or in a well-ventilated area.
• Open the fuel cap slowly. Do not overfill the tank. Do not fill the tank neck.
• Do not smoke or allow open flames or sparks in or near the area where refueling is performed or
where gasoline is stored.
Gasoline and gasoline vapors are poisonous and can cause severe injury.
• Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you swallow gasoline, inhale
more than a few breaths of gasoline vapor, or get gasoline in your eyes, see a physician
immediately.
• If gasoline spills on your skin or clothing, immediately wash it off with soap and water and change
clothing.
• If gasoline spills on the any part of the motorcycle, immediately rinse it off with water.
Exhaust gases contain carbon monoxide, a colorless, odorless gas that can cause loss of
consciousness or death in a short time.
• Never start the engine or let it run in an enclosed area.
• Never inhale exhaust gases.
18
Safety
WARNING
Safety Maintenance
Failure to perform safety maintenance as recommended can result in difficult handling and loss of
control, which could result in serious injury or death. Always perform the safety maintenance
procedures as recommended in this manual. Perform maintenance and repairs promptly as outlined in
the VICTORY Service Manual, or see your authorized VICTORY dealer for service.
• Before each ride, perform the pre-ride inspections. See page 34.
• Perform maintenance at the intervals specified in the periodic maintenance table. See page
52.
• Always maintain proper tire pressure, tread condition and wheel and tire balance. Inspect
tires regularly and replace worn or damaged tires promptly. Use only approved replacement tires. See the VICTORY Service Manual or your authorized VICTORY dealer.
• Always ensure proper steering head bearing adjustment.
• Regularly inspect the rear shock absorber and the front forks for fluid leaks or damage.
Make any necessary repairs promptly.
• Clean the motorcycle thoroughly to reveal items in need of repair. See page 81.
• Fasteners must meet original specifications for quality, finish and type to ensure safety.
Use only genuine VICTOR Y replacement parts, and ensure that all fasteners are tightened
to the proper torque.
19
Safety
Electromagnetic Interference
This vehicle complies with the requirements of European directive 97/24/EC Chapter 8,
United Nations ECE regulation 10 and Canadian ICES-002.
Reporting Safety Defects
If you believe that your vehicle has a defect that could result in a crash or cause injury or
death, you should immediately inform the National Highway Traffic Safety Administration
(NHTSA) in addition to notifying Polaris Industries in writing.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a
safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or
Polaris Industries.
T o contact NHTSA, or obtain other information about motor vehicle safety, you may call the
Vehicle Safety Hotline toll free at 1-888-327-4236 (TTY : 1-800-424-9153), visit the NHTSA
web site at www.safercar.gov, or write to:
ADMINISTRATOR, NHTSA
1200 New Jersey Avenue, SE
West Building
Washington, DC 20590
20
Safety and Information Labels
Warning
Label
Manufacturing
Information
Label (VIN)
Engine Identification Number
(stamped on right rear
crankcase half)
Emission Control,
Noise Information
Label
Tire Warning Label
(if applicable)
Patent
Notice
Tire Warning
Label
(if applicable)
Due to different model and market requirements, your vehicle may not have all of the labels
shown. Labels that apply to your model will be located as shown.
Handlebar Position Warning Label
(if equipped)
Safety
(under side cover, on side of fuse box cover)
Fuse and Relay Label
Fuse Box Removal Instruction Label
(on base of fuse box)
21
Component Identification
3
5
1
9
11
4
10
9
7
8
2
6
(Models differ in appearance, but
locations are the same as shown)
6
3
1
19
2
4
5
7
13
8
9
10
11
12
14
16
15
20
17
18
Handlebar Area
1. Clutch Lever
2. Mirror
3. Speedometer
4. Indicator Light Panel
5. Tachometer (if equipped)
6. Front Brake Fluid Reservoir
7. Front Brake Lever
8. Throttle Control Grip
9. Switches
10. Throttle Cables
11. Fuel Cap
Left Side View
1. Front Turn Signal
2. Headlamp
3. Air Filter
4. Spark Plugs
5. Ignition Switch
6. Battery (under side cover)
7. Taillight
8. Rear Turn Signal
9. Rear Axle Adjuster (each side)
10. Rear Brake Caliper
11. Passenger's Foot Rest
12. Evaporative Emissions Canister
(California Models)
13. Oil Filter
14. Oil Drain Plug (under engine)
15. Sidestand
16. Operator's Foot Rest
17. Gear Shift Lever
18. Front Brake Caliper
19. Front Fork
20. Horn
22
Right Side View
1. Passenger Seat/Cowl
2. Rear Brake Fluid Reservoir
(under cover)
3. Diagnostic Connector
4. Fuses
5. Rear Shock Access
6. Front Turn Signal
7. Front Brake Caliper
8. Rear Brake Pedal
9. Operator's Foot Rest
10. Engine Oil Fill Cap/Dipstick
11. Drive Sprocket (under cover)
12. Passenger's Foot Rest
13. Drive Belt (under guard)
14. Exhaust Mufflers
14
13
Component Identification
2, 3, 4, 5
1
12
11
10
8
9
6
7
23
Component Identification
Engine Identification Number
The engine identification number is stamped
into the right crankcase half behind the rear
cylinder. The first 8 digits are the engine
model number. The last 5 digits are the serial
number.
vided on page 102.
Ignition Key Number
The ignition key identification number is
stamped into the shaft of each key . Record the
number in the space provided on page 102.
Ignition Switch
The ignition switch provides electrical power to the ignition, the lighting system and all electrical switches and buttons. The ignition key operates the ignition switch and parking lights.
OFF
All electrical circuits are inactive and the
ignition key can be removed.
ON
All electrical circuits are energized and the
ignition key cannot be removed. The headlamp, taillight, and instrument lights illuminate.
PARK (P)
The taillight, indicator lights, and license
plate light illuminate. The emergency
flashers can be activated, and the ignition
key can be removed. Push the ignition key
inward while selecting the PARK position.
Record the number in the space pro-
Engine Identification Number
Park
On
Off
24
Instruments, Features and Controls
Speedometer
Indicator
Lamps
Multi-Function
Display
Instrument Cluster
Speedometer
The speedometer displays vehicle
speed in either miles per hour (MPH) or
kilometers per hour (km/h).
Indicator Lamps
Lamp Indicates Condition
Neutral This lamp illuminates when the transmission is in neutral and the
High Beam This lamp illuminates when the headlamp switch is set to high beam.
ignition key is in the ON position.
Turn Signal The turn signal indicator flashes when the left, right, or both turn sig-
Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of
Check Engine This lamp illuminates momentarily when the ignition switch is in the
Cruise Control Engaged (if equipped)
Not used
nals (hazard) are active. If a bulb fails, or if there is a short circuit in
the signal system, the lamp flashes at more than twice the normal
rate.
fuel remains in the fuel tank.
ON position and the engine is off. This indicates proper function. If
this lamp illuminates while the engine is running, contact an
authorized VICTORY dealer promptly for diagnosis. The light will
remain on if the tilt sensor shuts down the engine. See page 47. If
abnormal sensor or engine operation is detected the light will remain
on as long as the fault condition exists. Retrieve the error codes for
diagnosis. See page 29. This lamp is also known as a malfunction
indicator lamp (MIL).
25
Instruments, Features and Controls
Instrument Cluster
Multi-Function Display
Use the mode button to toggle through the
modes of the multi-function display . Press and
hold the mode button to reset the trip odometers, average fuel economy, average speed and
trip hour meter.
Modes Available
Standard Modes Accessory Modes
Odometer Trip Odometer 2
Trip Odometer 1 Average Fuel Economy
Tachometer Instantaneous Fuel Economy
Gear Indicator Trip Hours
Clock Average Speed
DC Voltage
Ambient Air Temperature
Display Units (Standard/Metric)
The display can be changed to display either standard or metric units of measurement.
Tip: To exit the set-up mode at any time, wait 10 seconds.The display automatically exits and returns to
the odometer display.
Standard Display Metric Display
Distance Miles Kilometers
Fuel U.S. Gallons Liters, Imperial Gallons
Temperature Fahrenheit Celsius
Time 12-Hour Clock 24-Hour Clock
1. Turn the key to the OFF position.
2. Press and hold the mode button while turning the key to the ON position.
3. When the display flashes the distance setting, tap the mode button to advance to the
desired setting.
4. Press and hold the mode button to save the setting and advance to the next display
option.
5. Repeat the procedure to change remaining display settings.
26
Instruments, Features and Controls
Instrument Cluster
Multi-Function Display
Odometer
The odometer displays total distance traveled by the vehicle.
Trip Odometers
The ignition switch must be in the ON position to access the trip odometers. The trip odometers (Trip 1 and Trip 2) display total distance traveled since being reset. To reset a trip odometer, toggle to the trip odometer. Press and hold the mode button until the meter resets.
Engine Speed (Tachometer)
Engine speed displays in revolutions per minute (RPM).
Gear Position
A gear position displays only when the transmission is in gear and the motorcycle is moving.
Two dashes (--) display if the stop/run switch is in the RUN position and the motorcycle is
not moving while in gear. The dashes also display if the stop/run switch is in the STOP position.
“N” displays when the stop/run switch is in the RUN position and the transmission is in neutral.
Clock
Tip: The clock must be reset any time the battery has been disconnected or discharged.
1. Turn the key to the ON position. Use the mode button to toggle to the odometer display.
2. Press and hold the mode button until the hour segment flashes. Release the button.
3. With the segment flashing, tap the mode button to advance to the desired setting.
4. Press and hold the mode button until the next segment flashes. Release the button.
5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments. After completing the
1-minute segment, step 4 will save the new settings and exit the clock mode.
6. Turn the key to the OFF position.
Average Fuel Economy (Accessory)
This mode displays average fuel economy since being reset. To reset, toggle to this mode.
Press and hold the mode button until the meter resets.
Instantaneous Fuel Economy (Accessory)
This mode displays the instantaneous fuel economy of the motorcycle.
Trip Hours Meter (Accessory)
The trip hours meter displays total hours of operation since being reset. To reset, toggle to
this mode. Press and hold the mode button until the meter resets.
27
Instruments, Features and Controls
Instrument Cluster
Multi-Function Display
Average Speed (Accessory)
The average speed mode displays average vehicle speed since being reset. T o reset, toggle to
this mode. Press and hold the mode button until the meter resets.
DC Voltage (Accessory)
The volt meter displays battery voltage. If the engine is not running, approximate battery
voltage displays. If the engine is running, approximate charging voltage displays.
Ambient Air Temperature (Accessory)
If the accessory sensor is installed, toggle to this mode to display the ambient air temperature. The key must be in the ON position.
Diagnostic Functionality
Certain conditions will cause an error message to display in the screen. If this occurs, please
see your VICTORY dealer.
Message Location Indicates
LO DC Voltage Screen Voltage remains below 11.0 volts for more than 10 seconds
OV DC Voltage Screen Voltage remains above 15.0 volts for more than 10 seconds
ERROR All Checksum error (gauge malfunction)
28
Instruments, Features and Controls
Suspect Parameter
Number (SPN)
Error Code
Number (0-9)
Failure Mode Indicator (FMI)
Instrument Cluster
Multi-Function Display
Engine Error Codes
The error screen displays only when the
CHECK ENGINE light is on or when it goes on
and off during one ignition cycle. Error codes
are not stored. When the key is turned OFF, the
code and message is lost, but will reappear if the
fault reoccurs after restarting the engine.
If the CHECK ENGINE indicator lamp illuminates, retrieve the error codes from the display.
1. If the error codes are not displayed, use the
mode button to toggle until “Ck ENG” displays on the main line of the display.
2. Press and hold the mode button to enter the
diagnostics code menu.
3. Record the three numbers displayed in the gear position, clock and odometer displays.
4. Press and release the mode button to advance to the next error code.
5. Press and hold the mode button to exit the diagnostics code menu.
6. See an authorized VICTORY dealer for code details and diagnosis.
Low Oil Pressure Display
“LO OIL” displays under the following
conditions.
Engine oil pressure has
dropped while the
engine is running.
The key is turned to
ON.
The stop/run switch is
moved to STOP.
Condition Indicates Action Required
Oil pressure is below a
safe operating pressure.
The indicator circuit is
operating properly.
The system is operating
properly.
Stop the engine as soon as safely possible and
check the oil level. If the oil level is sufficient,
but “LO OIL” continues to display after restarting the engine, stop the engine immediately.
Have your dealer check the oil pressure switch.
None - After two seconds the display will return
to the most recently active menu.
Press and release the MODE button to return
to the most recently active menu.
29
Instruments, Features and Controls
Flasher
Switch
High/Low Light Switch
Horn Button
Turn Signal Switch
Clutch Lever
Mode Button
Left Handlebar Controls
Clutch Lever
Pull the lever toward the handlebar
to disengage the clutch. Gradually
release the lever to engage the
clutch. For smooth clutch operation,
pull the lever quickly and release it
gradually.
Tip: A clutch interlock switch prevents
the engine from starting when the
transmission is in gear and the
clutch is engaged. See page 47.
Mode Button
The mode button is located on the front side of the
left handlebar switch. Use the mode button to toggle
through the modes of the multi-function display.
See page 26. Use the mode button to set the display
units to either standard or metric units of measurement.
Emergency Flasher Switch (Hazard Switch)
Press the top of the switch to activate the emergency flashers. All turn signals will
flash. Press the bottom of the switch to cancel the flashers.
High Beam/Low Beam Light Switch
Press the upper portion of the switch to activate the high beam. Press the lower portion of the switch to activate the low beam. Press and hold the lower portion of the
switch to activate the momentary passing beam.
Horn Button
To sound the horn, press the horn button.
Turn Signal Switch
Move the turn signal switch to the left to activate the left turn signals. Move the
switch to the right to activate the right turn signals. A signal ends when speed or distance reach preset levels. To end a signal manually, move the switch to the center
and push it inward.
Momentary Feature: Move the turn signal switch left or right and hold it in that position. The signal flashes until the switch is released.
30
Loading...