VICOR VI-RUZNX-XXXX, VI-RUZMX-XXXX, VI-RUZLX-XXXX, VI-RUZKX-XXXX, VI-RUZJX-XXXX Datasheet

Input Characteristics

90-132/180-264Vac
U = Autoranging

Output Power/Current

V

out

≥ 5V V

out

< 5V

S = 300W S = 60A
P = 450W P = 90A
M = 600W M = 120A

Product Grade

E = 0°C to +85°C Case
C = 0°C to +85°C Case
I = -30°C to +85°C Case

Output Power/Current

V

out

≥ 5V V

out

< 5V

Y = 50W Y = 10A
X = 75W X = 15A
W = 100W W = 20A
V = 150W V = 30A
U = 200W U = 40A

Product Highlights

If you’re looking for the convenience
of a complete, low profile, agency­approved switching power supply,
look no further. The FlatPAC combines
Vicor’s workhorse VI-200 family of
DC-DC converters with a modular
package and front end subassembly to
provide from 50 to 600W of output
power from one to three outputs.

A flat plate heatsink for use in
conduction cooled applications may be
specified as an alternate to the standard
finned version by adding “CC” to the
end of the model number.

Vicor’s FlatPAC is also available with
a current controlled output using
BatMod converter modules of 12, 24,
or 48Vdc outputs. This option is
specified by appending “BM” or “BC”
(for conduction cooled versions) to the
end of the FlatPAC model number.

The FlatPAC’s contemporary design
allows us to configure your order
quickly and provide rapid turnaround
on standard models. It is truly a
complete power solution, enabling
you to spend more time designing your
system and less time worrying about
how to power it.

Features

➤ Microcontroller architecture
➤ Inputs: 115/230Vac autoranging
➤ Meets FCC Part 15, EN55022, Class B

conducted emissions

➤ 80-90% efficiency
➤ Any output: 1 to 95Vdc
➤ Module enable/disable (except LU series)
➤ UL, CSA, TÜV, VDE, BABT, CE marked

➤ Remote sense and current limit
➤ BUS OK and AC OK (except LU series)
➤ 40mS ride-through time
➤ OVP and thermal shutdown
➤ 1 output; up to 200W
➤ 1 or 2 outputs; up to 400W
➤ 1, 2, or 3 outputs; up to 600W

FlatPAC

™

50 to 600W
Autoranging
AC-DC Switchers

FlatPAC Configuration Chart

Typical Model: V I - R U – –
Input: 115/230Vac; Output 1: 5Vdc at 200W

Output 2: 12Vdc at 200W
Output 3: 12Vdc at 200W

# of

Total Power Part No. Converters Dimensions

50-200W VI-LU – 1 9.25" x 2.5" x 1.37"

(234,8 x 63,5 x 34,8mm)

200-400W VI-MU – 2 9.25" x 4.9" x 1.37"

(234,8 x 124,5 x 34,8mm)

300-600W VI-NU – 3 9.25" x 7.3" x 1.37"

(234,8 x 185,4 x 34,8mm)

100-400W VI-PU – 2 9.25" x 4.9" x 1.37"

(234,8 x 124,5 x 34,8mm)

150-600W VI-QU – 3 9.25" x 7.3" x 1.37"

(234,8 x 185,4 x 34,8mm)

150-600W VI-RU – 3 9.25" x 7.3" x 1.37"

(234,8 x 185,4 x 34,8mm)

UUUE110

Single
Outputs:

Dual
Outputs:

Triple
Outputs:

Options

BC= BatMod/Conduction

Cooled
BM= BatMod
CC= Conduction Cooled

Output Voltage

Z 2V M 10V K 40V
Y 3.3V 1 12V 4 48V
0 5V P 13.8V H 52V
X 5.2V 2 15V F 72V
W 5.5V N 18.5V D 85V
V 5.8V 3 24V B 95V
T 6.5V L 28V
R 7.5V J 36V

Output Power

V

out

≥ 5V V

out

< 5V

W = 100W W = 20A
V = 150W V = 30A
U = 200W U = 40A
S = 300W S = 60A
Q = 400W Q = 80A

FlatPAC 10/02 1 of 4

FlatPAC Specifications

(Typical at 25°C, nominal line and 75% load, unless otherwise specified.)

Input Characteristics

AC line input

Autoranging 90-132/180-264Vac
Line frequency 47 to 63Hz (C-grade and E-grade)

47 to 440Hz (I-grade)

Inrush current

115Vac operation 1 converter: 16A @ peak line; 2 converters: 23A @ peak line; 3 converters: 39A @ peak line
230Vac operation 1 converter: 32A @ peak line; 2 converters: 47A @ peak line; 3 converters: 78A @ peak line

Ride-through time (full load)

90/180Vac low line 5ms minimum

115/230Vac nominal line 40ms minimum
AC fail warning time 5ms minimum (low line, full load)
AC and BUS OK (2 converter and 3 converter models only)

Off state Vce = 70V maximum

On state Vcesat = 0.4V maximum @ 1mA (1.5mA max.)
Module disable (2 converter and 3 converter models only, optically isolated LED input)

Continuous forward current 1 mA to 30mA

Forward voltage 1.65V max. at 30mA

Dielectric withstand

Primary to chassis GND 2,121Vdc

Primary to secondary 4,242Vdc

Secondary to chassis GND 707Vdc

Output Characteristics (applies to each output individually)

E-Grade C-, I-Grade

MIN. TYP. MAX. MIN. TYP. MAX UNITS NOTES

Setpoint accuracy 1% 2% 0.5% 1% V

NOM

Load/line regulation 0.5% 0.05% 0.2% V

NOM

LL to HL, 10% to Full Load

Load/line regulation 1% 0.2% 0.5% V

NOM

LL to HL, No Load to full load
Output temperature drift 0.02 0.01 0.02 %/°C Over rated temperature
Long term drift 0.02 0.02 %/1k hours
Output ripple

2V 150mV 60mV 100mV p-p 20MHz bandwidth
5V 5% 2% 3% p-p 20MHz bandwidth
10-48V 3% 0.75% 1.5% p-p 20MHz bandwidth

Output voltage trimming

1

50% 110% 50% 110%

Total remote sense

compensation 0.5 0.5 Volts 0.25V max. neg. leg

OVP setpoint 125% 115% 125% 135%

V

NOM

Recycle power
Current limit 105% 135% 105% 125%

I

NOM

Automatic restart
Short circuit current

2

20% 140% 20% 130% I

NOM

Thermal Characteristics

Efficiency 78-88% 80-90%
Shutdown temp. — case 90 95 105 90 95 105 °C Cool and recycle power to restart
Operating temp. — case 85 85 °C See Thermal Curves

Mechanical Specifications

Weight

3

22.4 (652) 22.4 (652) Ounces (Grams)

Safety Agency Approvals

UL, CSA, TÜV, VDE, IEC950, CE Marked for low voltage directive, 73/23/EEC

Environmental Characteristics/Product Grade Designators

Storage temperature -20°C to +100°C (C-grade and E-grade)

-55°C to +100°C (I-grade)

Operating temperature (case) 0°C to +85°C (C-grade and E-grade)

-30°C to +85°C (I-grade)

EMI/EMC Characteristics (Performed on selected samples representative of the U Series FlatPac product family.)
Conducted emissions, LISN EN 55022 and FCC R&R, Part 15, Subpart B, Class B
Electrostatic discharge IEC 801-2, 1991, Level 4; ±8kV Contact, ± 15kV Air Discharge
RF radiated immunity, E-field IEC 801-3, 1984; 27MHz to 500MHz, 3 V/M, CW
Electrical fast transients/burst EN 61000-4-4, Level 2; ±1kV,
Surge immunity EN 61000-4-5, Class 3; ±2kV Line to Ground, ±1kV Line to Line

1

10, 12V and 15V outputs, trim range ±10%. Consult factory for wider trim range.

2

Output voltages of 5V or less incorporate foldback current limiting, greater than 5V incorporate straight line current limiting.

3

For MU, PU series, multiply value by 2; for NU, QU, RU series, multiply value by 3.

FlatPAC 10/02 2 of 4