VC-600 and VC-610 Series
COLOR DOME CAMERAS
About this manual
Dimensions : inch (mm)
INSTRUCTION MANUAL XX166-01-00
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
This installation should be made by a qualified service person and
should conform to the National Electric Code, ANSI/NFPA 70 and
all local codes.
Installers should use appropriate hardware mounting materials.
TROUBLESHOOTING LENS ADJUSTMENT
PRECAUTIONS
■ Do not open or modify
Do not open the case except during maintenance and
installation, as it may be dangerous and cause damages.
■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get inside the camera. It could cause fire, short-circuits or
damages.
■ Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■ Install away from electric or magnetic fields
■ Protect from humidity and dust
■ Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen
or boiler room, as the temperature may rise to high levels.
■ Cleaning
Dirt can be removed from the case only by wiping it
with a soft cloth moistened with a soft detergent solution.
■ Mounting Surface
The mounting surface material must be strong enough to
support the camera.
Before sending the camera out for repair, check the items
below.
If the problem persists after checking these items, contact
your service center.
■ If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■ If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
1. Adjust the panning(360˚) and tilt(60˚) position.
2. Set the zoom position by using Zoom Lever Screw.
3. Set the focus by using Focus Lever Screw.
4. Loosen set screws to adjust roll (turns camera position
top/bottom).
PAN - 360˚
TILT - 60˚
Zoom
Focus
Set Screw
(2x)
ROLL
■ CONNECTIONS
CONNECTIONS AND CAMERA SETTINGS
SPECIFICATION - VC-600, VC-600S SPECIFICATION - VC-610, VC-610S
CAUTION
The use of a UL Listed Class 2 power supply is required to ensure
compliance with electrical safety standards.
Check for polarity when using a 12VDC power supply.
Red (+)
Black (-)
DC12V
AC2 4V
VIDEO
GENERAL Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
White Balance
WDR
Control DIP Switch
ME/AE DIP Switch Select ME/AE (ON/OFF)
ATW/AWB DIP Switch Select ATW/AWB (ON/OFF)
WDR ON/OFF DIP Swi tch Select WDR (ON/OFF)
AGC MAX ON DIP Switch Select ON/OFF
Electrical Spec
Operating Voltage 12VDC(10-20V), 24VAC(20-27V)
Power Consumption 12VDC - 3.7[W], 24VAC -4.0[W]
Mechanical Spec
Opertion Temp
14°F ~ 131°F (-10°C ~ +55°C)
Air Humidity Up to max.90%
Lens Mount 3.3-12mm
Connections via BNC(VIDEO), 2P WIRE(POWER)
Auto
ON or OFF (DIP S/W)
0.45
0.06fc, 0.6Lux(Scene) With F1.2 Lens
480TV Lines
10Vp-p/75ohm Composite
Internal / External (Line Lock)
> 45dB [AGC off]
GENERAL Spec NTSC PAL
HQ Interline Transf er CCD 1/3" 410K Pixels Color 1/ 3" 470K P ixels Col or
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC DIP Switch Select ON/OFF
ME/AE DIP Switch Select ME/AE (ON/OF F )
ATW/AWB DIP Switch Select ATW/AWB (ON/OFF)
AGC DIP Switch Select ON/OFF
Electrical Spec
Operating Voltage 12VDC(11-20V), 24VAC(20-27V)
Power Consumption 12VDC - 3.7[W], 24VAC -4.0[W]
Mechanical Spec
Opertion Temp
14°F ~ 131°F (-10°C ~ +55°C)
Air Humidity Up to max.90%
Lens Mount 3.3-12mm
Connections via BNC(VIDEO), 2P WIRE(POWER)
0.45
0.3Lux(Scene) Wi th F1.2 Lens
550TV Lines
10Vp-p/75ohm Composite
Internal / External (Line Lock)
> 48dB [AGC off]
■ CAMERA SETTINGS FOR VC-600, VC-600
S
■ CAMERA SETTINGS FOR VC-610, VC-610
S
● Confiming the wide dynamic range setting 3
WDR(ON) WDR is working
WDR(OFF) WDR is not working
● Setting gain control (AGC) 4
For adjusting the sensitivity of the camera.
Use this setting for shooting in dark environments.
ON Normal Setting
OFF Set this when there is excessive noise
● Compensating for backlight 1
ON When back light is too bright
OFF Normal setting
CAUTION : It will be correctly set by adjusting level volume 5.
● Confirming the iris setting 2
ME(ON) When DC auto-iris lens is ins talle d
AE(OFF) When fixed iris lens is installed
● Whi te balance se tting 3
ATW (ON)
Use this under light source below 2500K and over
9500K of natri um.
AWB (OFF)
Use this under light source between 2500K and
9500K of fluo rescent lamp, incande scent light.
●
Setting gain cont rol (A GC) 4
For adjusting the sens i tivi t y of the c amera.
Use this settin g for s hooting in dark environment s.
ON Normal Setting
OFF Set this when there is excessive noise.
● Adjusting level volume 5
If the entire image is too dark or bright, or the backlight
compen s a t i on is no t c orr ect, you ne ed to ad j u s t t h e l eve l vol u me.
CCW (LOW) Closes the lens iris, making the entire image darker
CW (HIGH) Opens the lens iris, making the entire image brighter.
● Confirming the iris setting 1
ME(ON) When DC auto-iris lens is installed
AE(OFF) When fixed iris lens is installed
●
White balance setting 2
ATW(ON)
AWB(OFF)
Use this under light source below 2500K and over
9500K of natrium.
Use this under light source between 2500K and 9500K
of fluorescent lamp, incandescent light
●
Confirming the iris setting 1
DC IRIS(ON) When DC auto- iris lens is installed
EE(OFF) When fixed iris lens is installed
NO. FUNCTION
1BLCOFFON
2AE/MEAEME
3ATW/AWBAWBATW
4AGC MAXOFF ON
DIP S/W
ON
OFF
1 2 3 4
INSTALLATION
1 Use the philips screwdriver to remove the screw (C).
2 Separate upper case (A) from bottom case (D).
3 Cut a hole (diameter:2.9inch/73mm) in the ceiling for
routing the cables.
4 Align the extension ring with the surface of the ceiling;
make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill the four
holes.
5 Pass the power cable (I) and video cable (H) from the
camera unit through the cable hole in the ceiling.
6 Align the four screw holes in the extension ring (G)
with the screw holes in the ceiling, and then secure
the camera in place by tightening four screws (F)
supplied with the unit.
7 Fixing mounting extension ring (G) on bottom case (D)
by using screw (B).
8 Carry out the settings and adjustments to the camera.
9 Adjust the dome liner (E) so that the dome camera's
lens is visible from the camera window and then
use a philips screwdriver to attach the dome cover.
10 Connect upper case (A) and bottom case (D).
11 Tighten the screw (C).
I
H
G
F
D
C
A
B
E
INSTALLATION WITH ADAPTER PLATE
1. Install Adapter Plate to existing electrical box in ceiling using 2 8-32 screws.
2. Perform steps 2 and 5 – 11 from above, installing the extension ring (G)
to the new plate instead of the ceiling.
Internet Address: www.vicon-cctv.com
Vicon Industries Inc.
Corporate Headquarters
89 Arkay Drive
Hauppauge, New York 11788
USA
631-952-CCTV (2288) 800-645-9116
Fax: 631-951-CCTV (2288)
European Headquarters
Brunel Way
Fareham, PO15 5TX
United Kingdom
+44(0) 1489 566300
Fax: +44(0) 1489 566322
Vicon Part number 8009-8166-01-00 Rev107
Germany
vin-videotronic infosystems gmbh
Lahnstrasse
D-24539 Neumuenster
Phone: +49 (0) 4321 8790
Fax: +49 (0) 4321 879 97
Loading...