Instruction Manual XX150-10
Introduction
The information in this manual covers the installation and setup of the V926-PHS Pendant Housing for the
Roughneck V926 Fixed-Position Camera Domes. This unit should be installed by a qualified technician using
approved materials in accordance with national, state and local codes. Read these instructions through
completely before attempting installation.
The V926-PHS provides pendant mounting for the Roughneck V926 Series Fixed-Position Camera Domes. Refer
to Installation and Operation Manual XX150 for V926 Camera Dome complete installation instructions. The
pendant housing was designed for use with any mount that supports the total weight of the V926 and V926-PHS
and adapts to a 1-inch NPT pipe thread. A 1-1/2-inch NPT bushing to 1-inch NPT nipple adapter is provided, if
required. Refer to Installation and Operation Manual for the selected mount for specific mounting information.
Installation
When the Roughneck V926 Dome Camera requires a pendant configuration, it must be installed in a V926-PHS
pendant housing. The mounting surface must provide suitable strength to support the weight of the V926 and the
V925-PH combined, which is approximately 6 lb (2.7 kg). Be sure the area in the selected location is clear of
obstacles (such as steel beams, headers, pipes, electrical wiring, etc.), which would interfere with mounting.
Video and power cables must be routed to the location. An adapter is provided, if necessary, to secure to a mount
with a 1-1/2-inch NPT-F thread. Follow the steps below and refer to Figures 1and 2.
1. Install the selected mount using appropriate hardware for the installation surface and run the cables through it
according to instruction manual for the mount.
2. Apply pipe sealant provided to the threads of 1-inch NPT pipe nipple on mount or threads of 1-1/2 x 1-inch
NPT adapter to create a seal. Screw the V926-PHS assembly onto the wall mount.
3. Run the cables through the V926-PHS. Be sure to have sufficient cable length to complete wiring.
4. Remove the electrical box from the V926 assembly by removing the two (2) screws that secure the camera
interface plate to the electrical box. Save the two screws and discard the electrical box.
5. Attach the tabs on the camera interface plate of the V926 to the V926-PHS mounting plate with the previously
removed 8-32 screws.
6. Remove the two (2) screws that hold the camera mounting bracket to the camera interface plate. Save the
two (2) screws. Make the cable connections to the connectors on the camera mounting bracket. See Figure 2
and refer to instruction manual XX150 if necessary.
7. Reattach the camera mounting bracket to the camera interface plate using the previously removed 6-32
machine screws.
8. Continue with the instructions in the Roughneck V926 installation manual for camera configuration.
Copyright © 2004 Vicon Industries Inc. All rights reserved.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
Product specifications subject to change without notice.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: +44 (0) 1489 566300 WEB: www.vicon-cctv.com
Part No. 8009-8150-10-00 Rev 804 Instruction Manual XX150-10 • 1
2 • Installation Part No. 8009-8150-10-00 Rev 804
Figure 1
Installation Diagram Exploded View
Figure 2
Cable Connections
Part No. 8009-8150-10-00 Rev 804 Installation • 3
Vicon Industries Inc.
Corporate Headquarters
89 Arkay Drive
Hauppauge, New York 11788
631-952-CCTV (2288) 800-645-9116
Fax: 631-951-CCTV (2288)
Vicon Europe
Headquarters
Brunel Way
Fareham, PO15 5TX
United Kingdom
+44 (0) 1489 566300
Fa 44 (0) 1489 566322 x: +
Brussels Office
Planet II - Unit E
Leuvensesteenweg 542
B-1930 Zaventem
Belgium
+32 (2) 712 8780
Fax: +32 (2) 712 8781
Far East Office
Unit 5, 17/F, Metropole Square
2 On Yiu Street, Shatin
New Territories,
Hong Kong
(852) 2145-7118
Fax: (852) 2145-7117
Internet Address: www.vicon-cctv.com
Loading...