”
VICON
‘)c
INSTRUCTIONS FOR
INSTALLATION AND OPERATION
NOTES
I
SHEET
REV. SEC.
SUPERSEDES ITGTFWC’IION
lHANuAL
x682781
X662 893 6
MODEL V8606H-XD MINIATURE CEILING HOUSING
1.
INTRODUCTION
The information in this manual covers the installation
a viewing window. The window is constructed of clear
of the
V8606H-XD
Miniatum Ceiling Housing. The
acrylic plastic. A special tool is provided for opening
installation of this equipment must be in conformance
and closing the tamperproof screw. Electrical connec-
with national, state, and local electrical codes.
tions are made through one of five knock-outs.
Model V8606H-XD is a miniature indoor camera enclo-
sure, constructed of two major parts: a steel upper
housing, into which the camera and lens am mounted,
and a tamperproof hinged lower housing or cover with
This compact unit is designed for very shallow ceiling
clearances. The housing accepts small CCD cameras
with either fixed-focal-length manual or
autoiris
lenses.
2. INSTALLATION
WARNING: Read ALL instructions
A
COMPLETELY before installing this unit. Failure to do so may result in costly installation
mistakes or personal injury to installers or other
persons.
CAUTION: Total weight of camera/lens assembly
A
should not exceed 10 pounds (4.5 kg).
The V8606HXD is designed to be mounted to most types
of ceilings. JnstaUion in a suspended ceiling requires
model
V8606H-XD-ACP,
an adjustable ceiling panel
which allows 360 degree position adjustment capability
for the
V8606HXD
housing.
The V8606H-XD
may
also be mounted in a panel supplied by the installer, but
the panel must be of a material (wood or metal) s&i-
ciently strong to support the combined weight of the
housing and camera/lens assembly.
‘Ibe V8606H-XD
weighs 6.0 lb (2.7 kg). Conventional ceiling tile and
sheet rock will not support this housing.
NOTE: For installation to a suspended ceiling,
see the instructions included with model
V8606H-XD-ACP.
2.1 Ceiling Preparation
1.
Be certain that the area directly above the selected2.Video, sync, and power cables must be routed near
location is clear of obstacles (such as steel beams,
the housing opening.
headers, pipes, electrical wiring, etc.) which would
interfere with the mounting of the housing. The
V8606H-XD
requires 7 inches (17.8 cm) of clear
space.
WARNING: TO PREVENT RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR
MOISTURE.
Product speoitkatiom subject to change without notice.
Copyright
@
1993 Vicon Industries Inc. Au rights reserved.
D
*L
Vicon
part
number
8006-8682-02-00
Vicon and its logo are registered trademarks of
WCOII
lndu~ttic~
Inc.
VICON
INDUSTRIES INC. 525 BROAD HOLLOW ROAD, MELVILLE, N.Y. 11747 TEL:
516-293-2200
FAX: 516-293-2627
TOLL FREE: l-600445-91 16
(OUTSIDE OF NEW YORK)
2.2 Permanent Ceiling Installation
NOTE: Total weight of camerallens combination
should not exceed 10 pounds (4.5 kg).
1.
Place the opened housing flush against the ceiling
and point the housing in the desired viewing direc-
tion.
2.
The
a cut hole in the ceiling using the metal
portion of the housing which is flush against the
wall. Be sure not to include the flange as part of the
cut hole measurement. The cut hole dimensions are
shown in Figure 1.
3.
Place the housing into the cut hole and use an awl
or other pointed object to identify the four (4)
mounting holes. Remove the housing and drill the
four holes into the ceiling.
4.
Insert the supplied liquid tight fitting into the appro-
priate knock-out (7/8-inch) and thread cables
through.
5. Mount the housing using four (4) hollow-wall
anchors with screws or toggle bolts.
6.
Assemble and adjust camera and lens as described
in the camera/lens instruction manuals.
NOTE: Extend the lensfully (shortestfocusing dis-
tance yields the greatest physical extension). This
prevents intelference between the lens and the hous-
ing window when the camera is in use.
7.
Mount the camera onto the mounting plate using the
screw and lockwasher provided.
8.
Connect the video and electrical cables and energize
the camera.
9. Observe the scene on a monitor and adjust the
camera mounting bracket for the desired viewing
angle.
NOTE: For detailed information on camera con-
nections and adjustments, refer to the appropriate
camera instruction manual.
10.
Check all hardware for tightness. Close and lock the
cover.
11. Cover the unused adjustment slots on the sides of
the housing with a piece of duct tape to protect the
housing from dust entry.
2.3 Suspended Ceiling Installation
NOTE: Installation in a suspended ceiling requires
either the V8606H-X.D-ACP adjustable ceiling panel
or a customer-supplied ceiling tile as described in the
introduction to Section 2, Installation. For detailed
instructions on installing the
V8606HXD
in a sus-
pended ceiling, refer to the instruction manual pro-
vided with the V8604H-XD-ACP.
3. MAINTENANCE
The V8606H-XD requires no regular maintenance other
than an occasional cleaning of the window. Use mild
soap and water or a nonabrasive plastic window cleaner.
2
X682-893
-
n.
:m)
in.
ml
for cabling
PEM nut projects
from each side of
I
t
5.50
in.
4.38
in.
(14.0
cm) (11.1 cm)
NOTE: Ceiling panel cutout
must be 10.75 in.
(27,3
cm)
long by 4.5 in. (11.4 cm) wide.
Allow clearance for the
PEM nuts on the sides of the
upper housing.
,
_--
-----
l
I
--
,L----
\
Dashed line indicates
location and size
of upper housing
c
-----
-
\--
------
10.50
in.
(26.7
cm)
12.25
in.
-(31.1
cm)
D
c
X682-893
Figure 1
Outline Drawing
3
Shipping Instructions
Jse the following procedure when returning a unit to
2. Attach a sheet of paper to the unit with the
he factory:
following information:
1.
Call or write Vicon for a Return Authorization
a.
@LA.) at one
of the locations listed below. Re-
cord the name of the Vicon employee who issued
b.
the RA.
Name and address of the company mtuming
theunit
I
Name of the Vicun employee who issued the
R.A
V-ICON INDUSTRIES INC.
525 Broad Hollow Rd.
Melville, NY 11747
516-293-2200 l-800-645-9116
C.
d.
e.
RA
number
VlCON
INDUSTRIES INC.
Western Regional
O&e
3259 Walnut Ave.
Long Beach, CA 90807
310-595-4280
l-800-648-1832
VICON INDUSTRIES INC.
Southeastem Regional Office
3010 Business Pa& Dr., Suite B
Norcmss, GA 30071
4044494499 l-800-824-8479
Brief description of the installation
Complete descripion of the problem and
circumstances under which it occurs
Unit’s original date ofpurchase, if still under
W-Q
f.
3.
Pack the tmit
auefully.
Use the original shipping
carton or its equivalent for maximum pmtcction.
4.
Ma& the RA. number on the outside of tbe
CaMn on the shipping
label
X682-893
Loading...