Vicon SurveyorVFT SVFT-C22C, SurveyorVFT SVFT-W22C, SurveyorVFT SVFT-W22, SurveyorVFT SVFT-P22, SurveyorVFT SVFT-C23 Installation And Operation Manual

...

XX134-07-00

Camera Dome

Warning: To reduce a risk of fire or electric shock, do not expose

the indoor unit to rain or moisture.

Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose.

Copyright © 2008 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. SurveyorVFT, NOVA and Vicoax are trademarks and ViconNet and Kollector are registered trademarks of Vicon Industries Inc. ExView is a trademark of Sony Corporation.

VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788

TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116

24-Hour Technical Support: 800-34-VICON (800-348-4266)

UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com

Vicon part number 8009-8134-07-00 Section 3 Rev 908

Important Safeguards – Outdoor Use

GRAPHIC SYMBOL EXPLANATION

The lightening bolt symbol alerts the user to the presence of dangerous voltage that may present the risk of electric shock.

The exclamation point symbol alerts the user to the presence of important operating and maintenance instructions.

1. Read Instructions - Read all safety and operating instructions before the product is operated.

2. Retain Instructions - Retain all safety and operating instructions for future reference.

3. Heed Warnings - Pay attention to all product warnings.

4. Follow Instructions - Follow all operating instructions.

5. Cleaning -(Do not use caustic, abrasive or aerosol cleaners)

a) For units that CAN BE DISCONNECTED from the power

source, use a damp cloth for cleaning.

units that CANNOT BE DISCONNECTED from the

b) For

power source, use a damp cloth for cleaning and do not allow moisture or liquids to enter vents.

6. Attachments - Use only UL Listed Vicon recommended attachments to prevent unit damage and personal injury.

7. Water and Moisture - Use only products designed for outdoor environments where they will be exposed to water or moisture.

8. Accessories - Do not place the unit on an unstable surface to avoid falling. Use only UL Listed Vicon recommended mounting accessories.

9. Ventilation - Do not block ventilating slots and openings as they ensure reliable operation. Do not place the unit near a heat source or into an enclosure unless recommended by Vicon.

10. Power Sources - The product should only be operated from the recommended power source. Use only a UL Class 2 indoor/dry or Class 3 outdoor/wet power supply.

11. Grounding - Only products equipped with a 3-prong grounded plug should be inserted into a grounded power outlet. Contact an electrician to replace an obsolete outlet. Do not force a plug into a non-grounded outlet.

12. Power Cord Protection - Power supply cords should not be routed in trafficked areas or in tight spaces where they will be pinched or used to bear weight. Allow some slack in the cord where it enters the unit.

13. Outdoor Cable Grounding - Use only grounded outdoor cables to protect against voltage surges and static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70-1984, provides information on proper grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors and the requirements of grounding electrodes.

14. Lightning - Disconnect the product from its power source and cable system when possible to prevent damage due to lightning and power-line surges.

15. Power Lines - Do not locate outside cables over power or utility lines where they can fall and make direct contact. Contact with power lines can be fatal.

16. Overloading - Do not overload wall outlets and extension cords to prevent risk of fire and electric shock.

17. Object and Liquid Entry - Never probe through, or spill liquid into, enclosure openings to prevent risk of fire or electric shock.

18. Servicing - Refer all servicing to qualified service personnel.

19. Damage Requiring Service - Obtain service when:

a) The power-supply cord or plug is damaged. b) Objects have fallen or liquid has been spilled into the

product.

c) The product is not designed for outdoor use and has been

exposed to water or moisture.

d) The product does not operate per the operating instructions.

Perform Vicon recommended adjustments, modifications and troubleshooting only to avoid unit damage and personal

injury. e) The product has been dropped. f) The product shows a significant change in performance.

20. Replacement Parts - Use only Vicon specified replacement parts or an approved equivalent to prevent unit damage and injury.

21. Safety Check - Request safety checks to be performed following repair or maintenance to verify proper operation.

22. ESD Precaution - Take all normal electrostatic discharge precautions to avoid component damage during installation and operation.

23. For 230 VAC Devices Only - When the disconnect device is not incorporated in the equipment or when the plug on the power supply is intended to serve as the disconnect device, follow the guidelines below: a) For permanently connected 230 VAC units, a readily

accessible disconnect device must be incorporated into the

site wiring. b) For 230 VAC units with a plug, the outlet must be installed

near the unit and be easily accessible.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 0BImportant Safeguards – Outdoor Use • 3

FCC Notice

Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a

Class A digital device.

WARNING

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specification in subpart B of part 15 of the FCC rules, which are designed to provide reasonable protection against such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient the receiving antenna.

• Relocate the equipment with respect to the receiver.

• Relocate the equipment away from the receiver.

• Plug the equipment into a different electrical outlet so that the equipment and receiver

are on different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.

The user may find the following booklet prepared by the Federal Communications Commission helpful:

“Interference Handbook, Bulletin CIB-2”

This booklet is available from the U.S. Government Printing Office, Superintendent of Documents, Mailstop SSOP, Washington, D.C. 20402-9328, ISBN 0-16-045542-1.

Warning: Power must be removed from this unit before removing circuit modules or ribbon cables.

Caution: This unit contains circuit cards with integrated circuit devices that can be damaged by static

discharge. Take all necessary precautions to prevent static discharge

Contents

IMPORTANT SAFEGUARDS...................................ERROR! BOOKMARK NOT DEFINED.

FCC NOTICE .........................................................................................................................I

CONTENTS .........................................................................................................................III

INTRODUCTION ...................................................................................................................1

How to Use this Manual.................................................................................................................................4

Accessory Kits................................................................................................................................................5

Unpacking and Inspection.............................................................................................................................5

SurveyorVFT Components............................................................................................................................8

Enclosure ..................................................................................................................................................8

Camera Drive............................................................................................................................................8

Shroud.......................................................................................................................................................8

Lower Dome..............................................................................................................................................8

Housing.....................................................................................................................................................8

Sunshield...................................................................................................................................................8

INSTALLATION..................................................................................................................11

Quick Installation – In-Ceiling Model..........................................................................................................11

Quick Installation – Indoor Pendant ..........................................................................................................12

Quick Installation – Outdoor Pendant........................................................................................................13

Detailed Installation .....................................................................................................................................14

In-Ceiling Mount Model...............................................................................................................................14

Use of the Provided Scribe .....................................................................................................................14

Indoor Pendant Model ................................................................................................................................19

Outdoor Pendant Model..............................................................................................................................22

WIRING...............................................................................................................................27

Typical Relay and Alarm Connections.......................................................................................................29

Installing the Cables ....................................................................................................................................30

For an In-Ceiling Installation ...................................................................................................................30

For an Indoor or Outdoor Pendant Model Installation.............................................................................31

Installation Configurations..........................................................................................................................35

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System • iii

Installing the Flash Upgrade and PC Direct Control................................................................................36

Standalone Configuration...........................................................................................................................36

Star Configuration ......................................................................................................................................37

CONFIGURATION ............................................................................................................. 39

Setting the DIP Switches.............................................................................................................................39

For RS-422/485 Mode:...........................................................................................................................39

For Vicoax Mode:....................................................................................................................................39

Setting the End-of-Line Jumpers JP1, JP2 & JP3 for RS-485 Protocol Operation................................42

Configuring the ViconNet (IP/LAN) Version...............................................................................................42

Configuring the Network Settings...........................................................................................................43

Using the VNSetup Utility....................................................................................................................43

ViconNet Configuration........................................................................................................................... 48

ViconNet (IP/LAN) Version Operation........................................................................................................ 48

UNINSTALLING THE SURVEYORVFT............................................................................. 49

For an In-Ceiling Installation...................................................................................................................49

For a Pendant Installation.......................................................................................................................49

OPERATION...................................................................................................................... 50

Initial Power-Up ......................................................................................................................................50

Verifying Proper Operation.........................................................................................................................51

Testing Preset 93.......................................................................................................................................51

Use of the Auto-Baud Detect Feature........................................................................................................51

Troubleshooting...........................................................................................................................................52

COMPETITIVE PROTOCOLS............................................................................................ 53

Testing Conditions..................................................................................................................................53

MAINTENANCE................................................................................................................. 61

Care and Cleaning of Metallized Domes....................................................................................................61

Care and Cleaning of Smoked and Clear Acrylic Domes........................................................................61

Fuse Replacement.......................................................................................................................................61

SHIPPING INSTRUCTIONS............................................................................................... 62

REFERENCE ..................................................................................................................... 63

TECHNICAL INFORMATION............................................................................................. 66

VICON STANDARD EQUIPMENT WARRANTY......ERROR! BOOKMARK NOT DEFINED.

iv • 2BContents XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Introduction

The information in this manual covers the installation, configuration and operation of the SurveyorVFT™ Camera Dome. This system should only be installed by a qualified technician using common hand tools and approved materials and wiring methods in accordance with the National Electrical Code ANSI/NFPA 70, state and local wiring codes. All interconnecting equipment or accessories must be UL Listed. Any mention in this manual of alarm inputs/outputs have not been evaluated by UL to be used for burglar alarm functionality.

NOTE: Read all instructions before beginning any installation.

The SurveyorVFT is a compact, lightweight intelligent security device comprised of a camera, pan/tilt drive, receiver and CPU-based electronics all in an attractive and covert enclosure. SurveyorVFT can be programmed and operated using any V1300X/V1400X/1500 series of NOVA™/Pilot communication devices and enhanced Vicoax™ II protocol and ViconNet variety of prepackaged configurations with choices in environment, mounting configuration, camera type, and lower dome types. Refer to Table 1 for a complete list of model numbers.

The basic SurveyorVFT provides video transmission over coaxial cable. Options are available that provide TCP/IP (ViconNet), fiber-optic and twisted-pair (UTP/NVT) video transmission. Each of these options includes an interface board that allows the specific type of video transmission. An appropriate receiver is required for UTP/NVT and fiber optic versions. The ViconNet option provides support for direct network connection to Kollector® Elite Digital Video Recorders and ViconNet Workstations via ViconNet Version 5 software. A preinstalled LAN interface board allows direct plug-in to a system network hub, switch or router. Video from the camera is available to all network recorders and workstations for live view and recording. The Vicon SurveyorVFT camera dome can be used in conjunction with competitive PTZ drivers through DIP switch selection. Audio input capability is available on the ViconNet version.

The SurveyorVFT is designed for easy snap-in installation. The drive simply snaps into the housing. When removed, the housing retains all programmed functions in its on-board memory. The customer interface board snaps down for easy access and the PCB provides removable terminal blocks for simple wiring connections. Several mounting accessories are available to fit almost any installation need.

There are four camera types available, each with NTSC and PAL versions. The basic model is a 22X highresolution camera/lens (CA in model number). Another 22X model is available with ExView™ CCD technology (22XEX). The third version is a 23X day/night camera/lens with wide dynamic range. The fourth model is a 35X day/night camera/lens with wide dynamic range and image stabilization. See Technical Information for camera features.

Refer to tables below for specific model numbers and options available. Call your Vicon representative for model availability. All versions use the same firmware for programming and operation. For programming, refer to the most recent version of SurveyorVFT Programming Manual XX134-40. The SurveyorVFT Camera Dome is compatible with the SVFT-UWM and SVFT-WM Wall Mounts, SVFT-UCM Ceiling Mount, SVFT-ICKT In-Ceiling Mount, SVFT-UCP Ceiling Panel, SVFT-URM-1 Roof Mount, and SVFT-UPM-1 Parapet Mount.

SurveyorVFT meets requirements for an FCC Class A computing device. SurveyorVFT complies with the fire code of certain local municipalities. The fire code for any given municipality should be verified for SurveyorVFT’s compliance at the installation site.

The electronic components within the SurveyorVFT are sensitive to damage from ESD (Electro-Static Discharge). Appropriate precautions and proper use of a ground strap should be observed at all times when handling the unit or its subassemblies.

digital management systems. SurveyorVFT is sold in a

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 3BIntroduction • 1

Table 1

Models and Descriptions

Model Number Product

Code

Environment/ Cable Type

Camera Type/Format

Mount Type

Optical Zoom/ Total Zoom

Lower Dome Type

SVFT-C22 8701-00 Indoor/Coax Color/NTSC Ceiling ExView 22x/264x Smoked SVFT-C22C 8701-01 Indoor/Coax Color/PAL Ceiling ExView 22x/264x Smoked SVFT-P22 8704-00 Indoor/Coax Color/NTSC Pendant ExView 22x/264x Smoked SVFT-P22C 8704-01 Indoor/Coax Color/PAL Pendant ExView 22x/264x Smoked SVFT-W22 8707-00 Outdoor/Coax Color/NTSC Pendant ExView 22x/264x Clear SVFT-W22C 8707-01 Outdoor/Coax Color/PAL Pendant ExView 22x/264x Clear SVFT-C23 8702-00 Indoor/Coax Color/NTSC

Ceiling 23x/276x Clear

(day/night)

SVFT-C23C 8702-01 Indoor/Coax Color/PAL

Ceiling 23x/276x Clear

(day/night)

SVFT-P23 8705-00 Indoor/Coax Color/NTSC

Pendant 23x/276x Clear

(day/night)

SVFT-P23C 8705-01 Indoor/Coax Color/PAL

Pendant 23x/276x Clear

(day/night)

SVFT-W23 8708-00 Outdoor/Coax Color/NTSC

Pendant 23x/276x Clear

(day/night)

SVFT-W23C 8708-01 Outdoor/Coax Color/PAL

Pendant 23x/276x Clear

(day/night)

SVFT-W35 9102-00 Outdoor/Coax Color/NTSC

Pendant 35x/420x Clear

(day/night)

SVFT-W35C 9102-01 Outdoor/Coax Color/PAL

Pendant 35x/420x Clear

(day/night) SVFT-C22CA 8741-00 Indoor/Coax Color/NTSC Ceiling 22x/264x Smoked SVFT-C22CA-C 8741-01 Indoor/Coax Color/PAL Ceiling 22x/264x Smoked SVFT-P22CA 8742-00 Indoor/Coax Color/NTSC Pendant 22x/264x Smoked SVFT-P22CA-C 8742-01 Indoor/Coax Color/PAL Pendant 22x/264x Smoked SVFT-W22CA 8743-00 Outdoor/Coax Color/NTSC Pendant 22x/264x Clear SVFT-W22CA-C 8743-01 Outdoor/Coax Color/PAL Pendant 22x/264x Clear

For the ViconNet (V5) option (Version 5), add -75 to the product code (-76 PAL); for Fiber Optic (F) option, add -30 to the product code (-31 PAL); for the Twisted Pair (T) option, add -40 to the product code (-41 PAL).

2 • 3BIntroduction XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Model Number

SVFT-C22/ SVFT-C22C SVFT-P22/ SVFT-P22C SVFT-W22/ SVFT-W22C SVFT-C23/ SVFT-C23C SVFT-P23/ SVFT-P23C SVFT-W23/ SVFT-W23C SVFT-W35/ SVFT-W35C SVFT-C22CA/ SVFT-C22CA-C SVFT-P22CA/ SVFT-P22CA-C SVFT-W22CA/ SVFT-W22CA-C

*Power @ 24 VAC.

Power Table

Power*

(W)

Coax, UTP, Fiber ViconNet Coax, UTP, Fiber ViconNet

Current Rating

(A)

24 34 1.0 1.4 24 34 1.0 1.4 44 54 1.8 2.3 24 34 1.0 1.4 24 34 1.0 1.4 44 54 1.8 2.3 44 54 1.8 2.3 24 34 1.0 1.4 24 34 1.0 1.4 44 54 1.8 2.3

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 3BIntroduction • 3

How to Use this Manual

This manual was designed to provide the best overall instructions for the installation and operation of the SurveyorVFT Camera Dome. The graphics and terminology used in this manual have been carefully selected to enable a clear and distinct understanding of the SurveyorVFT and its components. This manual has been formatted to present distinct methods of installation for qualified service personnel only.

For a quick overview of product installation, see the Quick Installation sub-section of the Installation section and choose the appropriate method (In-Ceiling Mount Model, Indoor Pendant Model or Outdoor Pendant Model) to begin. Follow the references provided in the text for items such as wiring tables, DIP switch settings and lower dome care. Refer to the subsequent sections of Installation, Wiring, Configuration and Operation for detailed descriptions of any method.

The Operation section of this manual was written using the available features in the latest revision of the SurveyorVFT software. The actual version of software may vary in any particular camera dome and support different features than actually described here.

4 • 3BIntroduction XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Accessory Kits

There are 3 different accessory kits included with the different configurations of SurveyorVFT; Standard/Fiber-Optic Option, Twisted Pair (UTP/NVT) Option and ViconNet (LAN/TCP/IP) Option. These kits provide the necessary items for installation as follows:

Standard/Fiber-Optic Versions

Description Quantity

8-position terminal block (1302-3313-02) 2 2-position terminal block (8004-8084-02) 1

Twisted Pair Version

Description Quantity

8-position terminal block (1302-3313-02) 2 2-position terminal block (8004-8084-02) 1 3-position terminal block (1302-3313-01) 1

ViconNet Version

Description Quantity

8-position terminal block (1302-3313-02) 1 2-position terminal block (8004-8084-02) 1 3-position terminal block (1302-3313-01) 1

NOTE: A packet of anti-seize lubricant is included in the outdoor housing accessory kit only. A scribe and a

strain relief are included in the in-ceiling unit accessory kit only.

Refer to the Wiring section of this manual for details on using the supplied removable termination blocks. The scribe is supplied to accurately measure the opening for the in-ceiling model. The lubricant is used for sealing and to prevent galling at the end of the 1.5-inch NPT pipe on the outdoor pendant model. Refer to the outdoor pendant model sub-section of the Installation section for details on applying the lubricant.

Unpacking and Inspection

All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to provide suitable delivery.

Inspect the cartons upon delivery and, if damage is present, make detailed notes on the carrier’s bill. Then, obtain the carrier agent’s signature and file a damage claim as soon as possible.

Open the cartons and inspect the equipment for damage. Save the cartons and packing material. If damage is present, contact the carrier and file a damage claim immediately. If the equipment must be returned for repair, follow the instructions in the Shipping Information section of this manual.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 3BIntroduction • 5

Unpacking the SurveyorVFT In-Ceiling

Unpacking the SurveyorVFT Indoor Pendant

6 • 3BIntroduction XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Unpacking the SurveyorVFT Outdoor Pendant

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 3BIntroduction • 7

SurveyorVFT Components

All SurveyorVFT units are comprised of an Enclosure/Housing, a Camera Drive, a Shroud and a Lower Dome. Figures 1, 2 and 3 show In-Ceiling, Indoor Pendant and Outdoor Pendant models, respectively.

Enclosure

The enclosure is a metal shell that houses the camera drive for the inceiling model. A safety cord and clip are provided to connect to the camera drive during installation. In addition, a small hole is provided on the side of the enclosure for connection of the lower dome’s safety cord. A removable top cover, a 0.75-inch (19 mm) conduit fitting and a pair of rotating flippers that give a convenient and sturdy connection of the enclosure into the ceiling are provided. For in-ceiling installations that do not use conduit pipe, a 0.75-inch (19 mm) strain relief fitting provides solid cable anchoring at the enclosure. A customer interface board, that can be unlatched or removed for easy access, is installed in the top of the enclosure. All wiring is done to this board.

Camera Drive

The camera drive is comprised of an integral camera, pan-and-tilt drive and CPU. It is designed for easy “snap-in” installation into the enclosure or housing. The camera drive quickly and accurately positions the camera in 360° of pan angle and 95° of tilt angle. There are variations in camera type for magnification and color or day/night usage. An additional thermostatically-controlled heater is provided for temperature control on outdoor units.

Shroud

The shroud is a 5.4 in. (137 mm) textured black ABS plastic shell. It has a 1.4 in. (35.6 mm) slotted opening for the camera. This shroud conceals the position of the camera and snaps onto the camera drive.

Lower Dome

The lower dome is an assembly comprised of a 5.98 inch (152 mm) diameter acrylic plastic shell, a trim ring and a safety cord. Lower domes for indoor versions come in a choice of smoked, chrome or gold finishes. Standard outdoor lower domes are clear and use 4 screws for additional support. All lower domes are anchored to the enclosure by the safety cord. Refer to the Maintenance section for care.

Housing

The housing for the SurveyorVFT indoor pendant configurations is a molded plastic protective cover for the camera drive; outdoor pendant configurations have a die-cast aluminum housing with a sunshield. The housing has a 1.5-inch NPT pipe flange mount. In addition, the housing is equipped with a safety cord and clip that is used to suspend the camera drive during installation. Another safety cord connects the lower dome to the housing. A customer interface board, that can be unlatched or removed for easy access, is installed in the top of the enclosure. All wiring is done to this board.

Sunshield

The sunshield is pre-installed over the housing used on the outdoor pendant version to minimize the effects of solar radiation.

Figure 1

SurveyorVFT In-Ceiling

CAUTION: For any environment subject to moisture, use the

outdoor pendant model.

8 • 3BIntroduction XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Figure 2

SurveyorVFT Indoor Pendant

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 3BIntroduction • 9

Figure 3

SurveyorVFT Outdoor Pendant

10 • 3BIntroduction XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Installation

Choose the installation type based on the specific unit purchased (In-Ceiling, Indoor or Outdoor Pendant).

Quick Installation – In-Ceiling Model

I C K

I N

S T

L L

I C K

I N

S T

L L

I O N

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 4BInstallation • 11

Quick Installation – Indoor Pendant

I C K

I N

S T

L L

I C K

I N

S T

L L

I O N

12 • 4BInstallation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Quick Installation – Outdoor Pendant

Q U

I C K

I N

S T

L L

I O N

Q U

I C K

I N

S T

L L

I O N

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 4BInstallation • 13

Detailed Installation

These steps provide the most thorough and accurate instructions.

In-Ceiling Mount Model

This version of SurveyorVFT mounts in the ceiling and rests on the ceiling material occupying the space between the lower ceiling and upper building frame. All mounting hardware is provided.

Use of the Provided Scribe

A small metal scribe is provided to assist in marking an accurate hole size in a ceiling tile for in-ceiling installations. Use as follows:

1. Place a ceiling tile on a large flat surface, face up.

2. Measure and make a small mark at position A from corner (11.9 in./302 mm). Refer to Figure 4.

3. Measure and make a small mark at position B (8.2 in./208 mm), placing the Scribe as perpendicular to the A-edge as possible.

4. Place the Scribe across positions B and C. Rotate the Scribe around center C for a full turn.

5. Cut out the circle, using a sharp tool, on the

Figure 4

Use of the Scribe

scribed line.

In-Ceiling Overview

The ceiling hole is cut using the scribe and the enclosure is prepared with flexible conduit or cabling. The enclosure is then lifted up through ceiling hole and the flipper screws are turned and tightened against the ceiling. Then the interface board is wired. The camera drive is hung from the enclosure’s safety cord and installed into the enclosure. The indoor lower dome is then snapped on. The SurveyorVFT is secured with the flippers. The SurveyorVFT’s horizontal position is determined by the hole placement. Refer to Figure 5 for installation details.

Figure 5

Ceiling Mount Model

14 • 4BInstallation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

The accessory kit contains the removable screw terminal blocks to be used for all connections in this installation.

The ceiling material must provide a surface of suitable strength for the SurveyorVFT weight of

5.1 lb (2.3 kg) on the area of the two flippers. Refer to the Optional Independent Support subsection for installations requiring additional support.

1. Mark, with the scribe, and cut a 7-3/8-inch

Figure 6

Unlatching the Customer Interface Board

(187 mm) diameter hole in ceiling at the desired location. Feed all flexible conduit pipe or cables down through the hole.

2. Unlatch the customer interface board and swing it 90º downward, providing access to terminal blocks. Refer to Figure 6. (The board can be completely removed, if necessary, by snapping it out of the hinge after rotated to the 90º downward position.)

3. If cables are used without the use of flexible conduit: a) Remove the conduit fitting by loosening the nut and sliding it out. Install the supplied strain relief

fitting in its place.

b) Hold the enclosure near the hole in the ceiling and route cables through the strain relief fitting.

3. If cables are channeled through flexible conduit: a) Hold the enclosure near the hole in the ceiling and route conduit cables through the conduit fitting. b) Insert the end of the flexible conduit pipe into the conduit fitting. Cable length should be flush with the

bottom of enclosure, approximately 9 inches (229 mm). Tighten the clamp screw.

4. Lift enclosure up through ceiling hole, turn and tighten flipper screws.

5. Remove terminal blocks from the accessory kit. The 2-pin is for power, the two (2) 8-pin are for alarms and control/relay; the 3-pin is for UTP option.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 4BInstallation • 15

Note: There should be minimal wire slack at all connection points.

a) Strip approximately 1 inch (25 mm) of cable outer jacket to be terminated in terminal blocks. Then

strip approximately 0.25 inches (6 mm) of insulation off of each individual wire.

b) Refer to Wiring section and Tables 2A, 2B and 2C to make all connections to terminal blocks TB1

(power), TB2 (alarms), TB3 (relays/control signals) and TB4 (UTP video). On TB3, the COMMAND IN + (COMM IN +) and COMMAND IN - (COMM IN -) connections must be used for Simplex operation. For Half Duplex operation, the additional signals RESPONSE OUT + (RESP OUT +) and RESPONSE OUT - (RESP OUT -) must also be used. Insert each wire into its terminal block loc ation and tighten the screw.

c) Terminate the video (coaxial) cable with a BNC type male connector, if not done previously. Refer to

Wiring section for video connections for fiber-optic, twisted pair or ViconNet optional video transmissions.

d) Terminate the 8-conductor alarm cable and the relay/control signals cable.

Skip step 6 for cable use with flexible conduit.

6. Loosen flipper screws and remove enclosure from ceiling. Slide cables back through fitting until terminal blocks are flush with the bottom of enclosure, approximately 9 inches (229 mm). Tighten conduit fitting and reinstall enclosure into ceiling by tightening flippers.

7. Install the terminal blocks TB1, TB2 and TB3 (and TB4) into the Customer Interface Board at the proper block frames. Install the video BNC cable connector to the Customer Interface Board’s mating BNC connector at location J1 (for standard coax installations); for UTP installations, connect twisted-pair video wires to screw terminal TB4. See Wiring section for video connections for fiber-optic and ViconNet versions. Swing up interface board to latch board into place. If interface board was completely removed, be sure to reinstall it correctly, with the white connector near the wall of the enclosure. Dress cables up over board to ensure there is no excess cable hanging past the board.

8. Configure the SurveyorVFT communication/protocol and address DIP switches on the main board at this time. See Setting the DIP Switch section of this manual.

16 • 4BInstallation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

9. Connect the enclosure’s safety cord clip to the tab in the camera drive to allow the drive to hang from the

enclosure. Refer to Figure 7 for location of tab. Insert the clip of the safety cord on the lower dome into the hole in the enclosure. Refer to label in the enclosure.

10. Align the 2 slots on the camera drive with the tabs in the enclosure, being sure to match up the arrows on

both the drive and in the enclosure. Insert the camera drive into the enclosure until it snaps into place.

11. Lift the lower dome up to the SurveyorVFT and line up the 2 molded tabs on the lower dome with the 2 recesses on the inner enclosure. Refer to Figure 8. There are only 2 ways to align it.

12. Push the lower dome up into the SurveyorVFT. Verify that it snaps into place on both sides. The upper edge of the lower dome should be flush with ceiling plane.

13. Proceed to the Operation section of this manual.

Figure 7

Safety Cord Installation

Figure 8

Final Assembly, Ceiling Mount Version

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 4BInstallation • 17

Optional Independent Support

If it is necessary to provide independent support for the SurveyorVFT, other than the ceiling material, order the optional In-Ceiling Model Mount Kit SVFT-IC-KT. It consists of a pre-assembled set of mounting rails and folding ring, as shown in Figure 9.

1. With the 7-3/8-inch (187 mm) diameter hole cut in the ceiling tile and tile replaced in the ceiling, push the folded assembly up through the hole and unfold.

2. Position the assembly squarely over the hole and fasten the caddy rail clips to the existing frame. Remove adjacent tiles to access the clips.

3. Adjust the position of the caddy rail clips along the frame to obtain the best “X” position.

Figure 9

tional In-Ceiling Model Mount Kit Installation

Figure 10

Optional In-Ceiling Model Mount Kit Installation Ring Location

4. Slide the assembly along the caddy rails to obtain the best concentric “Y” position. Tighten the horizontal adjustment screws to secure the position.

5. With the ring concentric with the hole, slide the ring vertically along the support slots to obtain the best flush fit in the ceiling. The ring should be firmly seated against the tile without warping the tile, as shown in Figure 10.

6. Finally, complete the installation as described in the procedure of the previous sub-sections. In this installation, the flippers will secure the enclosure to the mounting ring assembly instead of the tile.

18 • 4BInstallation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Indoor Pendant Model

The indoor pendant model mounts on a Vicon mount (refer to the table in the Introduction section) or a 1.5inch vertical pipe with an appropriate coupling. The pipe is a standard 1.5-inch NPT type and must be oriented vertically so the SurveyorVFT can effectively hang from the pipe.

Indoor Pendant Overview

The mount is installed with all the cables run through it or the 1.5-inch NPT pipe is prepared for SurveyorVFT installation. The cables are routed through the housing and the housing is screwed tightly to the pipe. Then the customer interface board is wired. The SurveyorVFT camera drive is hung from the housing safety cord. The SurveyorVFT drive is then carefully snapped into the housing. The SurveyorVFT is supported by the mount. The indoor lower dome is snapped on. Refer to Figure 11. Detailed installation instructions follow.

The accessory kit contains the removable terminal blocks for all connections in this installation. The mount must provide a support of suitable strength for the indoor pendant SurveyorVFT weight of 4.7 lb (2.1 kg).

Figure 11

Indoor Pendant Mount Model

1. Install the mount in accordance with the installation manual included with the mount or prepare the vertical 1.5-inch NPT pipe.

2. Feed all necessary cables through the back of the mount or out the end of the 1.5-inch NPT pipe.

3. Unlatch and rotate the customer interface board 90º downward to provide access to the terminal blocks. Refer to Figure 12. (The board can be completely removed if necessary by snapping it out of the hinge after being rotated to the 90º downward position.)

5. Lift the housing up to the mount or pipe and feed the cables through its top opening.

6. Place the housing onto the pipe and screw clockwise, looking up at the housing. When snug, turn an additional quarter-turn.

7. Remove the terminal blocks provided in the accessory kit. The 2-pin is for power, the two (2) 8-pin are for alarms and control/relay; the 3-pin is for UTP option. Terminate all the cables as follows:

a) Strip approximately 1 inch (25 mm) of the

cable outer jacket to be terminated in terminal blocks TB1 and TB3. Then strip approximately

0.25 inches (6 mm) of insulation off of each individual wire.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 4BInstallation • 19

Figure 12

Unlatching the Customer Interface Board

b) Refer to Wiring section and Tables 2A, 2B and 2C to make all connections to terminal block TB1

(power), TB2 (alarms), TB3 (relays/control signals) and TB4 UTP video). On TB3, the COMMAND IN + (COMM IN +) and COMMAND IN - (COMM IN -) connections must be used for Simplex operation. For Half Duplex operation, the additional signals RESPONSE OUT + (RESP OUT +) and RESPONSE OUT - (RESP OUT -) must also be used. Insert each wire into its terminal block loc ation and tighten the screw.

c) Terminate the video (coaxial) cable with a BNC type male connector, if not previously done. Refer to

Wiring section for video connections for twisted pair, fiber-optic or ViconNet optional video transmissions.

d) Terminate the 8-conductor alarm cable and the relay/control signals cable.

8. Slide excess cable back up into the mount/pipe so that cable length is flush with the bottom of the housing, approximately 8-9 inches (203-229 mm).

Note: There should be minimal wire slack at all connection points.

9. Install the terminal blocks TB1, TB2, TB3 and TB4 into the Customer Interface Board at the proper block frames. Install the video BNC cable connector to the Customer Interface Board’s mating BNC connector at location J1 (for standard coax installations); for UTP installations, connect twisted-pair video wires to screw terminal TB4. Refer to the Wiring section for video connections for fiber-optic and ViconNet versions.

10. Swing the customer interface board back into place. If interface board was completely removed, be sure to reinstall it correctly, with the white connector near the wall of the enclosure. After wiring is complete, dress cables up over board to ensure no excess cable is hanging past the board.

11. Configure the SurveyorVFT communication/protocol and address DIP switches on the main board at this time. Refer to the Setting the DIP Switch section of this manual.

WARNING: Cables having excessive slack can cause damage to the SurveyorVFT when installed into the

housing.

20 • 4BInstallation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

12. Lift the SurveyorVFT camera drive up to the housing and attach the housing’s safety cord clip to the camera drive’s tab. See Figure 13. Allow the drive to hang from the housing. Insert the clip of the safety cord from the lower dome into the hole on the inside of the housing. See label inside housing.

13. Align the tabs on the camera drive with the slots in the housing, matching up the arrows on the camera drive and the housing.

14. Push the camera drive straight up into the housing until it snaps into the housing. Do not use excessive force. In the event that it does not snap easily, remove the SurveyorVFT and verify proper cabling.

15. Holding the lower dome, line up the 2 molded tabs on the lower dome with the 2 parallel surfaces on the housing. Push the lower dome up and verify that it snaps into place on both sides. See Figure 14.

16. Proceed to the Operation section of this manual.

Figure 13

Safety Cord Installation

Figure 14

Indoor Lower Dome Installation

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 4BInstallation • 21

Outdoor Pendant Model

The Outdoor Pendant model mounts on a Vicon mount (refer to the table in the Introduction section) or a 1.5inch vertical pipe with appropriate coupling in the same manner as the indoor version. The outdoor version includes a sunshield, heater and weather protection.

Outdoor Pendant Overview

The mount is installed with all the cables run through it or the 1.5-inch NPT pipe is prepared with lubricant for the housing and the SurveyorVFT installation. The cables are routed through the housing and the housing is screwed tightly to the pipe. Then the customer interface board is wired. The SurveyorVFT is hung from the housing safety cord. The SurveyorVFT drive is then carefully snapped into the housing. The entire SurveyorVFT is supported by the mount. The outdoor lower dome is then snapped on and screwed tight to the SurveyorVFT. See Figure 15. Detailed installation instructions will follow.

The accessory kit contains the removable terminal blocks to be used for connections in this installation. The mount must provide a support of suitable strength for the outdoor pendant SurveyorVFT weight of 7.7 lb (3.5 kg).

1. Install the mount in accordance with the installation manual included with the mount or prepare the vertical 1.5-inch NPT pipe.

2. Feed all necessary cables through the back of the mount or out the end of the

1.5-inch NPT pipe.

3. Unlatch and rotate the customer interface board 90º downward to provide access to the terminal blocks. (The board can be completely removed if necessary by snapping it out of the hinge after rotated to the 90º downward position.)

4. Apply the provided anti-seize lubricant to the first 2-3 unpainted threads of the housing.

5. Lift the sunshield/housing up to the mount and feed the cables through its top opening.

6. Place the housing onto the 1.5-inch pipe and screw clockwise, looking up at the housing. When it becomes snug, turn it an additional quarter-turn.

Figure 15

Outdoor Pendant Mount Model

7. Remove terminal blocks from the accessory kit. The 2-pin is for power, the two (2) 8-pin are for alarms and control/relay; the 3-pin is for UTP option. Terminate all the cables as follows:

22 • 4BInstallation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

a) Strip approximately 1 inch (25 mm) of the cable outer jacket to be terminated in terminal blocks TB1

and TB3. Then strip approximately 0.25 inches (6 mm) of insulation off of each individual wire.

b) Refer to Wiring section and Table 2 to make all connections to terminal block TB1 (power), TB2

(alarms), TB3 (relays/control signals) and TB4 UTP video). On TB3, the COMMAND IN + (CI+) and COMMAND IN - (CI-) connections must be used for Simplex operation. For Half Duplex operation, the additional signals RESPONSE OUT + (RO+) and RESPONSE OUT - (RO-) must also be used. Insert each wire into its proper terminal block location and tighten the screw.

c) Terminate the video (coaxial) cable with a BNC type male connector, if not previously done. Refer to

Wiring section for video connections for fiber-optic or ViconNet optional video transmissions.

d) Terminate the 8-conductor alarm cable or communication/relay cable.

8. Slide excess cable back up into the mount/pipe so that cable length is flush with the bottom of the housing, approximately 8 - 9 inches (203 - 229 mm).

Note: There should be minimal wire slack at all connection points.

9. Install the terminal blocks TB1, TB2, TB3 and TB4 into the Customer Interface Board at the proper block frames. Install the video BNC cable connector to the Customer Interface Board’s mating BNC connector at location J1 (for coax installations) or connect twisted-pair video wires to screw terminal TB4 (for UTP installations). Refer to the Wiring section for video connections for fiber-optic and ViconNet versions.

10. Swing the customer interface board back into place. If interface board was completely removed, be sure to reinstall it correctly, with the white connector near the wall of the enclosure. Refer to Figure 16. After wiring is complete, dress cables up over board

11. Configure the SurveyorVFT communication/protocol and address DIP switches on the main board at this time. Refer to the Setting the DIP Switch section of this manual.

12. Lift the SurveyorVFT camera drive up to the housing and attach the housing’s safety cord clip to the camera drive’s tab. See Figure 17. Allow the drive to hang from the housing. Insert the clip of the safety cord from the lower dome into the hole on the inside of the housing. See label inside housing.

13. Align the tabs on the camera drive with the slots in the housing, matching up the two arrows on the camera drive and the housing.

WARNING: Cables having excessive slack can cause damage to the SurveyorVFT when installed into the

housing.

Unlatching the Customer Interface

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 4BInstallation • 23

Figure 16

Board

15. Holding the lower dome, line up the 2 molded tabs on the lower dome with the 2 parallel surfaces of the housing. Push the lower dome up and verify that it snaps into place on both sides. See Figure 18.

16. Tighten the 4 trim ring captive screws to hold the lower dome in place. Verify proper orientation of the grommet.

17. Proceed to the Operation section of this manual.

Figure 17

Installing the Safety Cords

24 • 4BInstallation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Figure 18

Outdoor Lower Dome Installation

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 4BInstallation • 25

NOTES

26 • 4BInstallation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Wiring

Wiring is done with runs of cable for power, video and control. Optional wiring can be installed for the relay output and alarm inputs. All cables enter the enclosure from the top on all pendant installations and through the conduit fitting on all in-ceiling installations. Refer to the Technical Information section for all electrical requirements.

Power cables carry AC power and are usually a two-conductor type ranging in size from 20 to 12 AWG. The power source used should be a UL listed Class 2 indoor/dry or Class 3 outdoor/wet rated type power supply. The leads should be connected to Terminal Block 1 (TB1). The size of the two-conductor cable depends on indoor/outdoor application and cable distance as shown in Table 4 of the Technical Information section. Refer to the table in the Introduction for power supplies available from Vicon (single and multi-channel).

In the standard version, video cables carry the composite video signal and Vicoax signals out of the SurveyorVFT over coaxial cable. In Vicoax mode, the video signal also carries the control signals. The video cable should be connected to the BNC female connector J1 for installations using coaxial cable; for UTP installations, twisted-pair video wires should be connected to TB4. For the fiber-optic version, video is carried through connector J2 on the customer interface board to a “daughter board” with a standard fiber-optic connector. For the ViconNet version, video is digitized and made available through the RJ-45 LAN connection. Refer to the Reference section of this manual for information on recommended cable types and maximum distances.

For the standard coax and twisted-pair versions, control cables carry the Pilot/NOVA/VPS digital signals and require individually-shielded twisted-pair sets. The RS-422/485 signal carries the Pilot/NOVA/VPS protocol (data). The RS-422 protocol is used for single camera dome applications. RS-422 signals are always active and do not have a tri-state (high impedance) state. The RS-485 protocol is used for multiple camera domes in a daisy chain configuration. RS-485 signals are not always active and do have a tri-state (high impedance) state. Thus, up to 32 SurveyorVFT units maximum (at a maximum distance of 5000 ft (1524 m) end-to-end) can be daisy chained to any other compatible RS-485 device, including another SurveyorVFT. Refer to the customer interface board and Figure 19 for signal connection points. The type of cable required depends on the cable distance and number of wire pairs within a cable, as shown in the Reference section. These signals are connected to Terminal Block 3 (TB3). There can be a maximum of two control cables (twisted-pair sets), depending on the mode selected, Simplex or Half Duplex operation. For the fiber-optic version, RS-422 data is carried through connector J2 on the customer interface board to a “daughter board” with a standard fiberoptic ST connector. For the ViconNet version, communication signals are digitized and are made available through the RJ-45 LAN connection. Refer to Figure 19.

Half Duplex: This RS-422/485 protocol type allows two-way command and response flow between the

SurveyorVFT and the control system that requires two individually-shielded twisted-pair cables.

Simplex: This RS-422/485 protocol type allows command flow from the control system to the

SurveyorVFT only requiring one shielded twisted-pair cable.

COMMAND IN ± (COMM IN): A signal from the CPU that causes some function to occur in the

SurveyorVFT.

RESPONSE OUT ± (RESP OUT): A signal from the SurveyorVFT to the CPU in response to a

COMMAND IN signal or triggered by an alarm input.

Additionally, there are two jacks provided for audio, JP2 (MIC) for Audio IN and JP1 (SPK) for Audio OUT. At this time, JP1 is not available.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 5BWiring • 27

Figure 19

Customer Interface Board Connections

28 • 5BWiring XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Typical Relay and Alarm Connections

Alarm input and relay output type signals are also carried on individually-shielded twisted-pair cable sets. The signals are defined in the following descriptions. Alarms 1-4 are electronic CMOS level type inputs that are driven by a dry contact type switch. These signals

are connected to terminal block TB2. Each input has two states, open and closed. For example, in Figure 20, a door switch can activate an alarm when connected to a SurveyorVFT alarm input. As a guideline (under normal conditions), the cable should be 22 AWG for a 1000 foot (305 m) distance. The states correspond to defined TTL designations as follows:

OPEN = HIGH and CLOSED = LOW where: HIGH = 5 VDC and LOW = < 1 VDC

Since dry contact switches are normally defined in terms of their inactive or “normal” state, the following holds true:

Figure 20

Typical Alarm Circuit

The “active” state can be programmed through the SurveyorVFT menu system. These signals are

NORMALLY CLOSED (NC) = ACTIVE HIGH (OPEN)

NORMALLY OPEN (NO) = ACTIVE LOW (CLOSED)

connected to terminal block TB2. Alarm signals can be programmed for their status (enabled/disabled), active level definition (high/low), action/reset function (none, preset, aux on, aux off or tour), acknowledgment mode (automatic, momentary or manual) and report status (yes/no).

The relay output is an actual relay output dry contact, which directly drives external devices (1.5 A @30 VDC max). For example, a light can be turned on and off when the relay output is connected to the light circuit. Refer to Figure 21. The relay output contact can be programmed for its power-on state definition (on/off) and output type definition (momentary or latching).

There is one relay output dry contact located on terminal block TB3. Connect the circuit to be switched to the connector pins labeled RELAY C (relay common) and RELAY NC or RELAY NO for a normally closed or normally open connection, respectively.

Figure 21

Typical Relay Circuit

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 5BWiring • 29

Installing the Cables

WARNING: Disable the AC power to prevent installer injury and damage to the unit.

Cables are installed using 2 different methods, depending on the installation type. For the in-ceiling installation, cables are routed from above the ceiling through a conduit fitting on the enclosure to the customer interface board. For the pendant installation, cables are routed from the inside of the housing to the customer interface board. In all cases, there should be minimal wire slack at all connection points. After wiring is complete, dress the cables so they are up over the board. Each camera dome version requires some different wiring connections. Refer to Figure 19 for individual customer interface board connections.

For an In-Ceiling Installation

1. Place all cables through the conduit fitting on the side of the enclosure. Verify that all cables have been routed through 0.75 inch (19 mm) rigid or flexible conduit pipe.

NOTE: If conduit pipe is not used, the supplied strain relief fitting must be installed in place of the one

installed to provide sufficient cable strain relief.

2. If using flexible conduit, cut all cables to their approximate required lengths. Leave approximately 1 inch (25 mm) extra for termination. Tighten fitting.

3. Remove terminal blocks from the accessory kit. The 2-pin is for power, the two (2) 8-pin are for alarms and control/relay; the 3-pin is for UTP option.

4. Strip approximately 1 in. (25 mm) of the cable outer jacket used for power, control, UTP video (optional), alarms and relays. Then strip approximately 0.25 inches (6 mm) of insulation off of each individual wire.

5. Terminate the video (coaxial) cable with a BNC type male connector. Terminate the 8-conductor alarm cable and relay/control signal cable.

6. Make all connections to terminal blocks TB1 (power), TB2 (alarms), TB3 (relays/control signals) and TB4 (UTP video) with reference to Tables 2A, 2B and 2C, depending on version. On TB3, the COMMAND IN + (COMM IN +) and COMMAND IN - (COMM IN -) connections must be used for Simplex operation. For Half Duplex operation, the additional signals RESPONSE OUT + (RESP OUT +) and RESPONSE OUT (RESP OUT -) must also be used.

7. Install the terminal blocks TB1, TB2, TB3 and TB4 into the Customer Interface Board at the proper block frames.

8. Install the video BNC cable connector to the Customer Interface Board’s mating BNC connector for the standard version. ALTERNATE CONNECTION: For the model using the UTP video connection, use the twisted-pair video wires. Attach each wire to screw terminal TB4. This signal is polarized and specific wire connections (+ or -) are marked on the board. Refer to the instructions supplied with the receiver for those connections. For fiber version, use standard ST connector on “daughter board.” For ViconNet, connect an RJ-45 connector to J1 on the board.

9. On installations not using flexible conduit, slide back excess cable and insert the conduit pipe into the conduit fitting and tighten the screw.

30 • 5BWiring XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

For an Indoor or Outdoor Pendant Model Installation

Refer to Figure 19 customer interface boards for indoor or outdoor pendant model mount cable installation details.

1. Route each cable from the inside top of the housing.

2. Remove terminal blocks from the accessory kit. The 2-pin is for power, the two (2) 8-pin are for alarms

and control/relay; the 3-pin is for UTP option.

3. Strip approximately 1 inch (25 mm) of the cable outer jacket used for power, control, UTP video (optional)

alarms and relays. Then strip approximately 0.25 inches (6 mm) of insulation off of each individual wire.

4. Terminate the video (coaxial) cable with a BNC type male connector. Terminate the 8-conductor alarm

cable and the relay/control signal cable.

5. Make all connections to terminal blocks TB1 (power), TB2 (alarms), TB3 (relays/control signals) and TB4

(UTP video) with reference to Tables 2A, 2B, 2C, depending on version. On TB3, the COMMAND IN + (COMM IN +) and COMMAND IN - (COMM IN -) connections must be used for simplex operation. For half duplex operation, the additional signals RESPONSE OUT + (RESP OUT +) and RESPONSE OUT (RESP OUT -) must also be used.

6. Slide excess cable back up into the mount/pipe so that cable length is flush with the bottom of the

housing, approximately 8 to 9 inches (203 to 229 mm).

7. Install the terminal blocks TB1, TB2, TB3 and TB4 into the customer interface board at the proper block

frames. Install the video BNC cable connector to the customer interface board’s mating BNC connector. ALTERNATE CONNECTION: For the models using the UTP video connection, use the twisted-pair video wires. Attach each wire to screw terminal TB4. This signal is polarized and specific wire connections (+ or -) are marked on the board. Refer to the instructions supplied with the receiver for those connections. For fiber version, use standard ST connector on “daughter board.” For ViconNet, connect an RJ-45 connector to J1 on the board.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 5BWiring • 31

CONNECTOR/PIN

NUMBER

TB1-1 TB1-2

TB2-1 TB2-2 TB2-3 TB2-4 TB2-5 TB2-6 TB2-7

TB2-8

TB3-1 TB3-2 TB3-3 TB3-4 TB3-5 TB3-6 TB3-7 TB3-8

CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME

BNC (female)

AMP Header

(Fiber Optic board)* Video/RS-422 data TERMINAL BLOCK

TERMINAL BLOCK

VIDEO (J1)

VIDEO

POWER (TB1)

H N

LARM (TB2)

ALARM 1

GND

ALARM 2

GND

ALARM 3

GND

ALARM 4

GND

COMM/RELAY (TB3)

COMM IN +

COMM IN -

RESP OUT +

RESP OUT -

GND

RELAY C

RELAY NO

RELAY NC

Video output

Hot

Neutral

Alarm input 1

Ground

Alarm input 2

Ground

Alarm input 3

Ground

Alarm input 4

Ground

Command in + Command in -

Response out +

Response out -

Ground

Relay, common

Relay, normally open

Relay, normally closed

*J2 connection provided to accommodate optional fiber optics interface board that provides video and

RS-422 full duplex data through a standard fiber optics connector.

Table 2A

Wiring Connections – Standard Coaxial/Fiber Optic Versions

32 • 5BWiring XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

CONNECTOR/PIN

NUMBER

TB4-1 TB4-2

TB4-3

TB1-1 TB1-2

TB2-1 TB2-2 TB2-3 TB2-4 TB2-5 TB2-6 TB2-7

TB2-8

TB3-1 TB3-2 TB3-3 TB3-4 TB3-5 TB3-6 TB3-7 TB3-8

CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME

TERMINAL BLOCK

VIDEO NVT (TB4)

UTP +

UTP -

GND

POWER (TB1)

H N

LARM (TB2)

ALARM 1

GND

ALARM 2

GND

ALARM 3

GND

ALARM 4

GND

COMM/RELAY (TB3)

COMM IN +

COMM IN RESP OUT+ RESP OUT -

GND

RELAY C RELAY NO RELAY NC

Unshielded twisted pair +

Unshielded twisted pair -

Hot

Neutral

Alarm input 1

Ground

Alarm input 2

Ground

Alarm input 3

Ground

Alarm input 4

Ground

Command in +

Command in -

Response out+

Response out -

Ground

Relay, common

Relay, normally open

Relay, normally closed

Table 2B

Wiring Connections – UTP Version

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 5BWiring • 33

J1-8

CONNECTOR/PIN

NUMBER

TB1-1 TB1-2

TB2-1 TB2-2 TB2-3 TB2-4 TB2-5 TB2-6 TB2-7 TB2-8

TB4-1 TB4-2

TB4-3

J1-1 J1-2 J1-3 J1-4 J1-5 J1-6 Receive J1-7

JP1 JP1 (MIC) Audio In JP2 JP2 (SPK) Audio Out - N/A

CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME

TERMINAL BLOCK

RJ-45

1/8-IN. PHONO AUDIO

POWER (TB1)

H N

LARM (TB2)

ALARM 1

GND

ALARM 2

GND

ALARM 3

GND

ALARM 4

GND

RELAY (TB4)

RELAY C RELAY NO RELAY NC

LAN (J1)

TX +

TX -

RX +

RX -

Hot

Neutral

Alarm input 1

Ground

Alarm input 2

Ground

Alarm input 3

Ground

Alarm input 4

Ground

Relay, common

Relay, normally open

Relay, normally closed

Transmit +

Transmit Receive +

Table 2C

Wiring Connections – ViconNet Version

34 • 5BWiring XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Installation Configurations

There are two types of installation configurations for coaxial, twisted-pair and fiber-optic domes, daisy-chain or star, depending on the needs of the system. A daisy-chain loops signals from one unit to the next. There can be a maximum of up to 5000 ft (1524 m) from the CPU, keypad or V1400X-IDL to the last dome in the chain. A star configuration provides multiple communication paths. By fanning out communications, system reliability increases; a failure on one leg of a star has no affect on the other units. The star configuration requires the use of a Distribution Line Control, such as Vicon’s V1400X-IDL that can support up to 10 domes. Refer to the figure below for an illustration of sample configurations. Both types of configurations can be used within a system.

Note: For daisy chain operation, the DIP switch must be set to RS-485 protocol; for star operation the DIP

switch must be set to RS-422 protocol. Refer to Configuration section for setting the DIP switch.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 5BWiring • 35

Installing the Flash Upgrade and PC Direct Control

It is possible to upgrade software for the SurveyorVFT through a PC and to control the SurveyorVFT from a PC. There are two system configurations, a standalone system, with one dome and one PC, and a star configuration, using a V1400X-IDL.

Note: The Flash Upgrade and PC Direct Control Software do not work with the ViconNet (IP) model of the

SurveyorVFT.

Note: A Flash Upgrade cannot be performed on a Vicoax system.

Note: The Flash baud rate must be the same as the Operational baud rate; if this is not the case, turn off the

intelligence switch on the V1400X-IDL.

Before the software for the SurveyorVFT can be upgraded, it is necessary to setup the hardware. Additionally, software for the PC must be ordered; the disk provides both the flash upgrade utility, needed to upgrade the firmware in the dome to latest version, and the PC Direct Control Software, which allows a host PC to control several domes through a GUI. Call Technical Support at 1-800-34-VICON (1-800-348-4266).

Standalone Configuration

Vicon recommends the standalone configuration, connecting the output of the RS-232/RS-422 converter directly to the SurveyorVFT data line. When one PC is being used with one dome, the PC must be connected to the SurveyorVFT by means of Vicon’s RS-232/RS-422 Interface Converter (part number 1240-5308-01) and a cable assembly (not provided). Fabricate the cable using 2 twisted pairs plus shield. See table below for pin out connections. Connect the converter to the SERIAL port on the PC. Connect the other end of the fabricated cable to COMM TB3 on the Communications/Power Supply PC Board. See following figure.

Pin Out Connections

RS-232/RS-422 Converter SurveyorVFT COMM TB3

Signal To Signal

RD(A) (RESPONSE IN -) PIN 4 (RESPONSE OUT -)

RD(B) (RESPONSE IN +) PIN 3 (RESPONSE OUT +)

G (GROUND) PIN 5 (GROUND)

TD(B) (COMMAND OUT +) PIN 1 (COMMAND IN +)

TD(A) (COMMAND OUT -) PIN 2 (COMMAND IN -)

36 • 5BWiring XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Standalone Configuration System

Star Configuration

When multiple domes are connected in a star configuration, using a V1400X-IDL, the RS-232/RS-422 Interface Converter is used, part number 1240-5308-01, along with a customer fabricated cable. Refer to Table 2A for connections. In this configuration, connect the converter end of the customer-fabricated cable assembly to the SERIAL port of the computer and the other end to the CPU/J11 port on the V1400X-IDL (you may have to disconnect the keypad). See following figure.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 5BWiring • 37

After the physical connections are made, insert the software disk and select the appropriate program, Flash Upgrade Utility or PC Direct Control Software.

38 • 5BWiring XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Star Configuration System

Configuration

The SurveyorVFT must be configured for its address and mode and termination setting when using RS422/RS-485 protocol. The address and mode are set using the two 8-position DIP Switch banks SW1 and SW2. It is necessary to determine which communication mode, Camera/Lens Module type and SurveyorVFT address is required prior to configuration. Configuration should be performed just prior to final assembly and installation. The termination setting is configured using 3 jumpers. This termination setting does not apply to RS-422 mode.

Setting the DIP Switches

This section defines how to set DIP switches 1 and 2 (SW1 and SW2) on the Main Board.

Refer to Figure 22 for DIP switch location and Figure 23 for DIP switch label. DIP switch 1 (SW1) is used to set the address as explained later. DIP switch 2 (SW2) is used to set the mode functions and protocol. Position 1 is the video mode setting, NTSC (ON) or PAL (OFF). Position 2 is the communication mode setting, Vicoax mode (ON) or Serial (OFF). Serial selection enables twisted pair compatibility to other manufacturer’s protocol. Position 3 is the communication type setting, SIMPLEX (ON) or HALF DUPLEX (OFF). Position 4 is the protocol mode setting, RS-485 (ON) or RS-422 (OFF). Switches 5-8 select other manufacturer’s protocols. Each switch is numbered from 1 to 8 and marked to indicate the ON position. SurveyorVFT will automatically detect the system’s baud rate and supports 4800, 9600 and 19,200 kb/sec rates.

Figure 22

DIP Switch Location

specified in Table 3. All addresses between 0 and 255 are valid (address 0 is the same as camera number 256). See Figure 23.

2. Set switch 1 on DIP switch 2 (SW2) to the appropriate video mode (PAL/OFF or NTSC/ON).

3. Set switch 2 on DIP switch 2 (SW2) to the OFF position (SERIAL).

4. Set switch 3 on DIP switch 2 (SW2) to the appropriate communication mode (SIMPLEX or DUPLEX).

5. Set switch 4 on DIP switch 2 (SW2) to the appropriate communication protocol (RS-422 or RS-485).

6. Set switches 5-8 on DIP switch 2 (SW2) to the appropriate manufacturer protocol. See Figure 23.

For RS-422/485 Mode:

1. Set switches 1 - 8 on DIP switch 1 (SW1) to SurveyorVFT’s address as

NOTE: Switch 4 must be set to RS-485 protocol to enable daisy chain operation; switch 4 must be set to

RS-422 protocol to enable star operation.

NOTE: All SurveyorVFTs in a daisy chain or star configuration must have unique addresses for proper

operation.

For Vicoax Mode:

1. Set switch 1 on DIP switch 2 (SW2) to the appropriate video mode (PAL or NTSC).

2. Set switch 2 on DIP switch 2 (SW2) to the ON position (Vicoax mode).

3. Set switches 3 and 4 on DIP switch 2 (SW2) to either position, as it does not affect Vicoax protocol operation.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 6BConfiguration • 39

NOTE: DIP switches labeled ON or CLOSED and OFF or OPEN have the same meaning.

Figure 23

DIP Switch Label

Competitive Protocol Settings, SW2 Switches 5-8

Pelco: Switch 5 is ON, switches 6-8 are OFF Sensormatic: Switch 6 is ON, switches 5, 7, 8 are OFF Ultrak: Switches 5 and 6 are ON, switches 7-8 are OFF Philips: Switch 7 is ON, switches 5, 6, 8 are OFF Cohu: Switches 5 and 7 are ON, switches 6 and 8 are OFF Kalatel: Switches 6 and 7 are ON, switches 5 and 8 are OFF Panasonic: Switches 5 and 8 are ON, switches 6 and 7 are OFF NTCIP: The dome is specifically coded from the factory or flash upgraded. It cannot

be switched to other protocols without first flashing the firmware back to standard factory protocol. Switches 5-8 are not used and switch 3 must be OFF for Duplex. LAN (ViconNet): SW2 Switches 3 and 4 are OFF; switch 1 on SW1 to ON

Caution: Competitive protocols are not available in LAN (ViconNet) mode.

Note: For Pelco Keypad with 2400 baud, switch 3 on SW2 must be set to ON; Pelco is D protocol.

40 • 6BConfiguration XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

DIP Switch 1 (SW1) Address (Pilot/NOVA/VPS Mode)

SWITCHES SWITCHES SWITCHES

#12345678#12345678#12345678

0 86XXXX172 XXX 1X 87XXX X X 173X XX X X 2 X 88 X X X 174 X X X X X 3XX 89X XX X 175XXXX X X 4 X 90XXXX176 XX 5XX 91XXXXX177X XX 6XX 92 XXXX178X XX 7XXX 93X XXX X 179XX XX X 8 X 94 XXXX X 180 X XX X

9X X 95XXXXX X 181X X XX X 10 X X 96 X X 182 X X X X X 11XX X 97X XX 183XXX XX X 12 X X 98 X X X 184 X X X X 13 X X X 99 X X X X 185 X X X X X 14 X X X 100 X X X 186 X X X X X 15XXXX 101X X XX 187XX XXX X 16 X 102 XX XX 188 XXXX X 17X X 103XXX XX 189X XXXX X 18 X X 104 X X X 190 X X X X X X 19XX X 105X X XX 191XXXXXX X 20 XX 106XXXX192 X 21XXX 107XXXXX193X X 22 XX X 108 XX XX 194 X XX 23XXX X 109X XX XX 195XX XX 24 XX 110 XXX XX 196 X XX 25 X X X 111 X X X X X X 197 X X X X 26 X X X 112 X X X 198 X X X X 27XX XX 113X XXX 199XXX XX 28 X X X 114 X X X X 200 X X X 29X XXX 115XX XXX 201X X XX 30 XXXX 116 X XXX 202 X X XX 31XXXXX 117XXXXX203XXX X 32 X 118 X X X X X 204 X X X X 33 X X 119 X X X X X X 205 X X X X X 34 X X 120 X X X X 206 X X X X X 35XX X 121X XXXX 207XXXX XX 36 X X 122 X XXXX 208 X XX 37 X X X 123 X X X X X X 209 X X X X 38 X X X 124 X X X X X 210 X X X X 39XXX X 125X XXXXX 211XX X XX 40 X X 126 XXXXXX 212 X X XX 41X XX 127XXXXXXX213XXXX 42 X X X 128 X 214 X X X X X 43 X X X X 129 X X 215 X X X X X X 44 X X X 130 X X 216 X X X X 45 X X X X 131 X X X 217 X X X X X 46 X X X X 132 X X 218 X X X X X 47 X X X X X 133 X X X 219 X X X X X X 48 XX 134 XX X220 XXX XX 49 X X X 135 X X X X 221 X X X X X X 50 X X X 136 X X 222 X X X X X X 51XX XX 137X X X223XXXXX XX 52 X X X 138 X X X 224 X X X 53 X X X X 139 X X X X 225 X X X X 54 XX XX 140 XX X226 X XXX 55 X X X X X 141 X X X X 227 X X X X X 56 XXX 142 XXX X228 X XXX 57X XXX 143XXXX X229X X XXX 58 X XXX 144 X X230 XX XXX 59XX XXX 145X X X231XXX XXX 60 XXXX 146 X X X232 X XXX 61X XXXX 147XX X X233X X XXX 62 XXXXX 148 X X X234 X X XXX 63XXXXXX 149X X X X235XX X XXX 64 X 150 XX X X236 XX XXX 65X X 151XXX X X237X XX XXX 66 X X 152 X X X 238 X X X X X X 67XX X 153X XX X239XXXX XXX 68 X X 154 X XX X240 XXXX 69 X X X 155 X X X X X 241 X X X X X 70 XX X 156 XXX X242 X XXXX 71XXX X 157X XXX X243XX XXXX 72 XX158XXXXX244XXXX 73 X X X 159 X X X X X X 245 X X X X X X 74 X X X 160 X X 246 X X X X X X 75XX X X 161X X X247XXX XXXX 76 X X X 162 X X X 248 X X X X X 77 X X X X 163 X X X X 249 X X X X X X 78 XXX X 164 X X X250 X XXXXX 79XXXX X 165X X X X251XX XXXXX 80 X X 166 X X X X 252 X X X X X X 81 X X X 167 X X X X X 253 X X X X X X X 82 X X X 168 X X X254 XXXXXXX 83XX X X 169X X X X255XXXXXXXX 84 XXX170XXXX 85XXXX171XXXXX

Table 3

DIP Switch 1 (SW1) Settings for Pilot/NOVA/VPS Mode

X X X

X X

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 6BConfiguration • 41

Setting the End-of-Line Jumpers JP1, JP2 & JP3 for RS-485 Protocol

Operation

Figure 24

End-of-Line Jumper Location

NOTE: DIP Switch 2 (SW2) switch 4 must be set to the ON (RS-485) position for proper daisy chain

operation. The end-of-line jumpers do not affect RS-422 mode.

This section defines setting the end-of-line jumpers JP1, JP2 and JP3. The jumper sockets are located on the underside of the customer interface board, as shown in Figure 24.

NOTE: 32 units maximum can be daisy chained at a maximum distance of 5000 ft (1524 m) end-to-end.

The 3 jumpers are installed on each SurveyorVFT. There are 2 possible configurations as follows:

Jumpers Installed: For one camera dome or the last in line of a daisy chain using RS-485 protocol only. Jumpers Uninstalled: For all intermediate camera domes in a daisy chain using RS-485 protocol only.

1. Uninstall the SurveyorVFT camera drive to access the jumper sockets. Refer to the “Uninstalling the SurveyorVFT” section of this manual.

2. Verify that all 3 jumpers are installed over the 2 pins for each socket on a SurveyorVFT that is the only unit in a daisy chain or the last in line of a daisy chain.

3. Reassemble the SurveyorVFT and proceed to the Operation section of this manual for functional testing. Refer to the Installation section of this manual.

Configuring the ViconNet (IP/LAN) Version

The following information is provided when installing the ViconNet version of the SurveyorVFT (IP dome) only. The SurveyorVFT camera dome (IP version) is shipped with a CD that contains the ViconNet version 5 software needed to setup your IP system, including the application setup, the camera firmware and setup software (VNSetup). Be sure the ViconNet Workstation meets the minimum requirements, is running the ViconNet application (version 5) (VNSetup) and has the proper PTZ camera driver. The VNSetup is found on the included CD under software, IP Camera Setup. Refer to appropriate ViconNet documentation.

Network Considerations

The SurveyorVFT Camera Dome can be connected to any ViconNet network (Version 5 software). Kollector Elite Recorders and ViconNet Workstations can be used for live viewing and recording of network-streamed video. A network can be as simple as a single SurveyorVFT connected to a ViconNet Workstation or can be complex with the addition of several networks interconnected via WAN.

42 • 6BConfiguration XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

When adding a SurveyorVFT IP Camera to the ViconNet network, the following items must be considered:

• The number of cameras on a switch with respect to switch capabilities and system bandwidth mapping.

• Bandwidth limitations on ports connected to workstations (using 100 or 1000 Mbps).

• Workstation capabilities such as processing speed, disk write speed and display card strength.

• Storage size and location types including local Workstation recording, attached SCSI RAID and

integrated NAS/SAN devices.

The default parameters on the IP dome are:

Factory Defaults Network Defaults IP address Nucleus IP address Net Mask address Gateway address:

: [10.10.10.1] IP address: [1.1.1.2]

: [1.1.1.1] Nucleus IP address: [1.1.1.1] : [255.255.255.0] Net Mask address: [255.255.255.0] [0.0.0.0] Gateway address: [1.1.1.1]

On first startup, the camera will attempt to establish connection to the Nucleus with the default address (1.1.1.1). Connecting it to an active Nucleus is done through the VNSetup utility.

Note: When connecting to ViconNet application version 5, the number of concurrent users viewing video

from the same device cannot exceed 10 users.

Groups and Users Restrictions

ViconNet allows creating Multiple Groups and Users in order to limit the rights to different levels. For more information on how to create Users and Groups, refer to the latest revision of ViconNet manual XX113.

Although the ViconNet software does not limit the number of Groups and Users that can be created, the SurveyorVFT Camera Dome has Users and Groups limitations. For ViconNet version 5, the dome can support the first 20 Groups (including Administrators and Guests) and the first 100 Users.

Configuring the Network Settings

Note: Before starting, make sure that VNSetup is installed on the configuring PC\workstation. Installation is

done using the CD included.

There are two ways to change the IP dome network settings:

• Activating the camera for the first time: via VNSetup application.

• Connecting the camera to an active Nucleus: via ViconNet application (connection to same Nucleus as

the camera is necessary).

Note: In order to install firmware, the PC and camera must be on the same IP network.

Using the VNSetup Utility

VNSetup consists of several TABs. Each TAB provides different functionalities.

Note: Once the IP Camera Setup is run the first time, a shortcut is placed on the desktop for future use.

1. Make sure the MAC address and password of the camera is available. Use MAC Address log provided.

2. Verify that the camera is physically connected to the configuring workstation via the network.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 6BConfiguration • 43

Setup TAB

Note: Since the Setup configuration affects the entire installation process, it MUST be configured first.

In the Setup TAB, 3 fields are defined. The Upgrade files field indicates the installation upgrade directory. The Log files field allows the user the ability to put a copy of log files in a predefined directory. Password management selects a directory to save all password files. (By default, the setup files will be installed to

C:\VUG.) In Password file status, the number of passwords stored is displayed. Load a list of passwords is intended for very large sites only. Contact Technical Support to use this feature.

Setup

Select TAB

The Select TAB allows the user to select the relevant IP Unit in order to change its settings or to upgrade its version.

1. From the Unit selection list, select the relevant IP product. In case of multiple sites, it is advised to use the filter under the Unit Type field. Click on any column tab to sort names by that definition in ascending or descending order.

2. Once the desired unit has been selected, notice the order to change the selected unit’s settings on the local PC that is running the VNSetup, a unique password must be entered. The screen will display how many units there are and how many of those are password protected (locked). A remote unit, as in systems using network routers and VLANS (virtual LANs), will not display in the Unit selection list. If you want to select a remote unit, manually enter the IP address in the IP address of remote unit field and click Find remote unit. The remote unit is added to the list.

Note: This is correct for BIOS from version 1.0.10.86 and later (ViconNet version 3 and higher).

3. Password authentication There are two authentication options. You can either authenticate a specific unit, by entering its password, or use a Nucleus authentication, allowing you access to all units in the network.

3.1. Unit authentication - On the Unit password field, enter the unit password and press the Add password button. Once approved, notice that the

proceed to next phase. The password will be saved on this unit.

icon, indicating a password protected unit. In

icon has disappeared and the user may

Note: The unit password is supplied on the sticker with the MAC address in the camera package.

3.2. Nucleus authentication - On the Nucleus admin login field, enter a valid Nucleus IP address and password and press the Login button. Once approved, notice that the

disappeared from all proceed to next phase.

44 • 6BConfiguration XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

icon has

the units currently connected to the selected Nucleus and the user may

4. Press the Select button on the lower section of the screen.

Note: You MUST click the Select button to add the unit to the list; verify that it is added to the list.

5. The selected unit appears on the Selected unit section on the top of the screen and settings can be changed.

Select

3.2

Unit TAB

The Unit TAB allows the user to change the following settings: Unit name, Nucleus IP address, IP address, Net mask, Gateway, DNS, DHCP, Time Zone, daylight saving time, Local time, Local date, and Debug level, on a scale of 0-4, where 4 is most information.

Note: The Apply button must be pressed for changes to take effect.

Note: Verify all IP addressing parameters with your IT administrator.

Note: In order for the DHCP option to work properly, verify that the server does not expire the IP address

licensed to the camera. (Camera should always receive the same IP address from the DHCP server.)

Unit

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 6BConfiguration • 45

Install TAB

The Install TAB allows the user to install/upgrade newer versions. Choose the correct version and click Install to send to the selected unit.

Install

Info Tab

The Info TAB displays the selected IP product general information/

Info

Advanced TAB

The Advanced TAB functionalities allow the user to handle unexpected events on a specific remote unit when they occur.

When a problem occurs, the user can choose to Unjam unit to restart the unit’s firmware, Restart unit to restart the hardware, Net defaults to return the initial network settings and Factory defaults to return to the initial configuration.

The Main app starting mode, Application start status may be Unknown, Application loaded successfully or Loading of application is disabled. The Disable load button allows the pausing of the application load in case of software issues while still permitting communication via VNSetup; the Enable load button resumes the application load.

46 • 6BConfiguration XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Advanced

Custom TAB

The Custom TAB is only used for the KRX-3 Decoder. Do NOT do any settings in this screen.

Custom

After the SurveyorVFT has been configured for ViconNet, upon another boot up (or preset 97), the opening screen will display (see below). This screen displays the camera dome program version, current date/time and some of the word ViconNet. Upon completion of homing, the SurveyorVFT is ready to verify proper operation. (Note: Screen below is only a sample screen.) The word ViconNet remains on the screen until a PTZ action is taken.

Note: The camera drive always returns to the pan and tilt coordinates it was initially powered-up with unless

autohome on power-up was set.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 6BConfiguration • 47

ViconNet Configuration

After the camera dome has been setup with the proper IP address, configuration features from a remote workstation, server or recorder are available as follows.

• A network settings screen is used to modify the camera dome’s IP parameters. This allows great flexibility in network setup.

Note: This setup can be performed from any VN-WS/VN-NVR workstation connected to the IP dome and to

the Nucleus or from a Kollector Elite.

1. Verify that the camera is connected to the network, that it is active and that it is configured to use the same Nucleus.

2. From the workstation desktop, run the ViconNet application.

3. After logging in, open the site setup selection window.

4. Select the IP dome camera setup.

5. Open the Network Setup and Site Name setup window. Network Settings window will display. See Figure below.

6. Change the required parameters and click OK. (See your IT administrator for specific network parameters.) Application of the camera will restart.

• An Authorization screen is used to establish authority levels, by user group. Functions such as PTZ and video view, record and playback can be set for authority level.

• A priority screen is used to establish video quality and FPS levels.

ViconNet (IP/LAN) Version Operation

The following functions are supported by the ViconNet system through a workstation, recorder or server.

1. System macros can be configured to view and record the dome’s video. In addition, within macros, alarms can be sent and remote macros triggered.

2. An alarm can be triggered upon video motion detection and video loss. This alarm can be sent remotely to other networked units.

3. PTZ control can be performed from any networked workstation, recorder or server. Authorization for PTZ can be assigned to specific operator levels.

Refer to the ViconNet workstation manual XX113 for complete information on operation. A copy of the manual can be found on the CD included.

48 • 6BConfiguration XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Network Settings Window

Uninstalling the SurveyorVFT

The ur S veyorVFT camera drive can be easily uninstalled by simply pushing in the tabs to release the camera drive from the housing or the enclosure. A safety cord is always available to safely hang the camera drive or camera dome assembly while installing or uninstalling.

For an In-Ceiling Installation

1. Gently pull down on the lower dome’s outside edge, with two hands, until a molded tabs snap out of place.

2. Push in the tabs to release the camera drive from the enclosure. It will hang from the safety cor to Figure 25.

3. If it is necessary to completely remove the camera drive, disconnect the safety cord clip.

For a Pendant Installation

1. (Outdoor Pendant model only) Loosen the 4 trim ring screws from the outdoor lower dome.

2. Gently pull down on the lower dome’s outside edge, until it snaps out of place.

3. Push in the tabs on the housing until the SurveyorVFT camera drive is released. Refer to Figure 25.

Figure 25

Uninstallation

5. If it is necessary to completely remove the SurveyorVFT, disconnect the clip on the end of the safety cord from the latch on the housing.

4. Allow the SurveyorVFT to gently drop down until it is supported by the safety cord.

d. Refer

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 7BUninstalling the SurveyorVFT • 49

Operation

Following the complete installation and setup of the SurveyorVFT, it is necessary to perform initial power-up testing and verify proper operation. If the SurveyorVFT fails to power-up correctly, go to the Troubleshooting sub-section of this section. When initial power-up has been completed and verified, SurveyorVFT can be setup and operated in a normal fashion using a Vicon remote through a PC running the Surveyor Direct Control pro workstation.

Figure 26

Power-Up Test Screen

operator keypad, VPS/NOVA/Pilot unit or

igram; the V conNet can be run from a ViconNet

Initial Power-Up

1. Setup an appropriate monitor within the vicinity of the SurveyorVFT. Connect the video out cable to the monitor. Power-on the monitor verify that no signal is displayed.

2. Verify that the SurveyorVFT has been installed, wired accordance with this manual.

3. Switch the AC power on to the SurveyorVFT. The monitor will display the power-up test screen for the duration of its initial testing. This test displays the status of the functions pan, tilt, zoom, focus and the integrity of the memory (NVRAM). fails, “FAIL” displays in place of “PASS.”

The SurveyorVFT then switche4.

opening screen (Figure 27). This screen will display the camera dome program version, current date/time and some settings. Upon completion of homing, the SurveyorVFT is ready to verify proper operation. (Note: Figure 27 is only a sample screen.)

of the current DIP switch

and configured in

(Figure 26)

If any test

and

s to the

Figure 27

Opening Screen

50 • 8BOperation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

NOTE: The camera drive always returns to

the pan and tilt coordinates it was initially powered-up with unless autohome on power-up was set.

Verifying Proper Operation

Set up a remote keypad via RS-422/485 or a Pilot/NOVA/VPS CPU via RS-422/485 or Vicoax protocol to the SurveyorVFT. Power-on the control device and verify that it boots up. Set up the control device for operation with the SurveyorVFT in accordance with its Installation and Operation Manual.

For a Vicon model V1300X-RVC or V1300X-DVC keypad connected directly to the SurveyorVFT or through a CPU, use the following procedure to access SurveyorVFT programming:

1. Slide the keypad’s PGM-RUN switch to the PGM position.

2. Press the PP ENTER key; the PRESET LED displays a blinking 0.

3. Press the 9 and 4 numeric keys in that order.

4. Press the PP ENTER key again. The PRESET LED display remains with the number 94 and the monitor displays the SurveyorVFT Main

enu, as shown in Figure 28. M

5. Set up the SurveyorVFT as desired using the

Figure 28

Main Menu

In Duplex mode only, if the dome is not responding b (ex.,.autoiris, autopan, alarm), perform the following:

1. Press PP

2. Press the 9 and 3 numeric keys in that order.

3. If the LEDs on the A/I and A/P keys light, you

4. Press AUX2 to acknowledge baud rate/polarity.

ENTER key.

r unit is responding.

remote keypad. Proper operation has been verified.

Testing Preset 93

ack to the CPU that it is performing functions

Use of the Auto-Baud Detect F

Figure 29

Auto-Baud Detect Screen

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 8BOperation • 51

eature

Auto-baud detect functions after installing defaults, using preset 95, when switching Vicoax to Pilot/NOVA (VPS) and upon power-up when the dome sees an incorrect baud rate from keypad or contr

ol system. It allows the camera dome to detect

a ne

w baud rate from the host controller without having to cyc useful when remotely at system having a different baud rate. See Figure 29. (Note: Figure 29 is only a sample screen.)

After configuration of SurveyorVFT is complete, set the baud rate for the new host system before powering down and disconnecting as follows:

1. Slide the keypad’s PGM-RUN switch to the

PGM position.

le AC power. This feature is especially

the camera dome will be set up

one baud rate and installed into a

2. Press the PP ENTER key; the PRESET LED displays a blinking 0.

3. Press the 9 and 5 numeric keys in that order. . Press the PP ENTER key again. The PRESET LED display remains with the number 95. The monitor will

display the power-up test screen (Figure 26) for the duration of its initial testing.

5. The SurveyorVFT then switches to the opening screen (Figure 27). This screen will display the camera

dome program version, current date/time, the curr baud detect. Move the joystick or press buttons to send commands and commence auto-baud detect.

ent address and a request to send communications to

Troubleshooting

If the SurveyorVFT does not power-up correctly, chec ⇒ Check if the power LED DP2 on the Customer Interface Board is on. If the voltage is too low, the LED will

stay off.

⇒ Verify, with a voltmeter, that 18 to 32 VAC is mea

integrity of the power wiring. If less than 18 VAC is m too long. Check the maximum usable cable distance Technical Information section. If 18 to 32 VAC is measured, return the SurveyorVFT back to factory for service in accordance with the Shipping Instructio

⇒ If the last screen displays and does not disappear,

control device. Verify that the SurveyorVFT address is selected on the control device. Sometimes moving the joystick can begin communicati established, check the integrity of the control signal wiring. If all wiring is correct, swap the camera drive and re-check. If the new camera drive communicates, return the SurveyorVFT back to the factory for service in accordance with the Shipping

tr anual. Ins uctions section of this m

⇒ If the SurveyorVFT is intermittently operational or operating inde

signals on the terminal block. Also, verify that SW2, switch 3 is set f SurveyorVFT.

⇒ If the SurveyorVFT powers up but does not display an

cable connection. Verify that BNC connectors are atta addition, verify that the cable is not damaged. It is com somewhere along its run. If possible, check the outpu camera dome site.

on. If communication cannot be

k the following:

sured across TB1, pins 1 and 2. If not, check the easured, it is probable that the power cable length is

for the voltage input as stated in Table of the

ns section of this manual.

the SurveyorVFT is not communicating with the

pendently, it is possible that the

eck proper placecommunications (control) wiring is incorrect. Re-ch

y video, it is possible that there is a poor video

ched at the camera dome and monitor/CPU. In

mon for the cable to be stretched or squashed

t locally, with a portable monitor, at the actual

ment of the control and response

or Half Duplex in a Half Duplex wired

52 • 8BOperation XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Competitive Protocols

The SurveyorVFT Camera Dome can be operated by a number of co

utline how to use the functions on Pelco, Sensormatic, Kalatel, Ultrak, Panasonic, Philips and Cohu

o keypads.

Testing Conditions

elco: tested with the MPT9500 Controller and Pelco D protocol. SurveyorVFT P Pelco keypad using Pelco D protocol. Sensormatic: tested using the AD Tracker 16 via RCSN422 SensorNet to RS422 converter. SurveyorVFT should function with any Sensormatic (AD) keypad using SensorNet protocol.

alatel: tested with KTD-404, which requires a protocol converter KTD-410 to convert Kalatel’s DigipK

rotocol to ASCII RS-232 protocol; an RS-232 to RS-422 converter (with external power) is then required to

p connect the SurveyorVFT. The S function with any Kalatel keypad u Ultrak: tested with KEGS5000 keypad, which requires Ultrak control

85 and 1x RS-232 ports). For detailed information refer to Ultrak ke4 Keypad communication interface is RS-485: 9600 baud. The SurveyorVFT in Ultrak mode is simplex with event parity.8.1. SurveyorVFT should function with most Ultrak keypads using Ultrak KD6/KD6-Z protocol. (Version of the supported protocol: Ultr Panasonic: tested with WV-CU161 keypad, which does not require any port adapters. For detailed information refer to Panasonic keypad user manual connection diagram. Set keypad communication protocol to RS-485: 9600 baud, duplex, data bit 8, parity NONE, and stop bit 1. SurveyorVFT should function with most Panasonic keypads that utilize Panasonic WV-CS850(A) ver 3.0 protocol. (Version of the supported

protocol: Panasonic WV-CS850(A) ver 3.0, release date October 2001.)

hilips: Tested with LTC-5136 series keypad, which requires Bosch LTC 8P

converters (both converters must be self powered) to resample the signal from RS-232 to RS-422 protocol. For detailed information refer to Philips keypad user manual and converters user manuals. To enable Philips protocol set SurveyorVFT SW2 DIP switch 7 to ON position. Switches 2-6 and 8 must be set to OFF. Communication with the SurveyorVFT using Philips protocol is supported at RS-422: 9600 baud, data bit 8, parity NONE, and stop bit is 1. SurveyorVFT should function with most Philips keypads using Philips AutoDome TC8560/TC700 protocol. (Version of the supported protocol: Philips AutoDome TC8560/TC700

eries Release Date: March 2000.) S Cohu: Tested with WinMPC v4.2 software application, which requires Black Box RS 232 to RS 422 interface converter. For detailed information on wiring diagram refer to Cohu iDome user manual. To enable Cohu protocol set SurveyorSVFT SW2 DIP switches 5 and 7 to ON position. Switches 2, 6 and 8 must be set to OFF. Communication with the SurveyorVFT using Cohu protocol is supported at RS-422: 9600 baud, data bit 8, parity NONE, and stop bit is iDome/iView/LCU protocol. (Version of the supported protocol: Cohu iDome/iView/LCU Communication Protocol – Rev 3.0. Release Date: March 2004.)

Note: All companies make changes and improvements in their products. Because this product can interface with equipment not manufactured by Vicon, there is a possibility that the interface protocols

ay have changed sinm

commends purchasing a single unit for bench testing prior to purchasing and installing this

re product in quantity.

The Vicon SurveyorVFT is designed to store PTZ preset locations on the internal memory. Certain manufacturers’ controllers are designed to store PTZ preset locations in the controller. Therefore preset functionality in the Vicon dome will not work correctly with these types of controllers.

ce Vicon tested this product with the interfacing equipment. Vicon

urveyorVFT in Kalatel mode is simplex 9600, n, 8, 1. SurveyorVFT should

sing Digiplex protocol.

ak KD6/KD6-Z, release date June 2001.)

1. SurveyorVFT should function with most Cohu keypads that utilize Cohu

mpetitive protocols. The tables below

should function with any

lex

port adapter (RJ-11 connector to 1 x RS

ypad user manual connection diagram.

557 series and Qlty ICC-11

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 9BCompetitive Protocols • 53

Pelco

Function Keypress Function Keypress

Enter Menu

Select/Store IO (Iris Open)

Backup/Abort/Exit I C (Iris Close) Reset Dome F2

Iris Open Iris Open- Controls Autoiris Levels Set AP limits

Iris Close

Focus Near

Focus Far

Zoom Out

95, Preset Set (Program Label screen appears), F2 Set Transmit Polarity

Program Sectors

Iris Close - Controls Autoiris Levels

Focus Near

Focus Far

Zoom Wide

Set Pan limits

agnostic Screen

Debug Screen

Preset Tours

93, Preset Set (Program Label screen appear F2

96, Preset Set (Program Label screen appears), F2 then press Pan Auto to set sectors, Aux 2 and 3 to set mask.

97, Preset Set (Program Label screen appears),

92, Preset Set (Program Label screen appears), F2 then <2> Aux to set left limit and <3> Aux t set right limit

90, Preset Set (Program Label screen appears F2 then <2> Aux to set left limit and <3> Aux t set right limit

91, Preset Set (Program Label screen appear F2

99, Preset Set (Program Label screen appear F2

The controller MPT9500 doesn't support Pelco tours. Vicon's tours are ac cessible using preset 80-87 or the menu system. To store a tour, E preset number, Preset Set , F2. To run tour us Preset Go.

s),

nter

Pelco calls these patterns ; there are multiple ways of programming. The keypad has defaul shortcut keys. This maps t o our preset 88. It w not access preset 89. Press <1>, F1 to start programming . P ress <2>, F1 to stop programming. Press <3>, F1 t o run the tour. Programming using the Vicon way allows acce to autotours 88 and 89. To program tour 88 en <88>, Preset Set, F2 to s tart programming. A prompt appears to press Aux 1 to start programmin g. When the pattern i s complete press Aux 1 again to stop programming. The

Zoom In Camera Off Camera On

Autopan Pan Auto = On , Pan Man = Off Alarm Acknowledge

Autoiris No Control- Unit is always in autoiris. full) - (Pelco Feature) Turbo Button

Lens Speed

Auxs

Presets Preset Recall - Enter Preset Number, Preset Go V-Phase Menu system

Pan and Tilt Lockout

Zoom Tele Camera Off Camera On

8, F1, enter 1 or 2 for low, 3 for med , 4 for high. Zoom and focus speed are the same. Flip (Turn 180 degrees) 5,F1

Supports only a latching relay. Press <1>, Aux to e

ngage. Press <1> , F3 to disengage Feature) Not Supported

Preset Store - 1 to 32 , 35 to 79 - Ent e r Preset Number, Preset Set (Program Label screen appears), F2 - No preset label editing. Can be programmed through menu.

94, Preset Set (Program Label screen appears), F2. Repeat to unlock.

Auto Tour Night Mode- Manual <6> Aux to engage. <6> F3 to disengage Alarms Programmed through the menu system.

Turbo (Set speed to

Peel (Sensormatic

Camera Control Including Adjust

press IO to store or IC to abort. The tour can be programmed thru the menu system.

Enter any number from 1-9 and press "Al arm Ack". The SurveyorVFT will acknowlede the alarms in received order.

ill

ter

also

54 • 9BCompetitive Protocols XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Sensormatic

Function Keypress Function Keypress

Enter Menu Select/Store FF Program Sectors Not Supported

Backup/Abort/Exit Close Reset Dome Iris Open Open - Controls Manual Iris Levels Set AP limits Not Supported Iris Close Close - Controls Manual Iris Levels Set Pan limits Not Supported

Focus Near

Focus Far

Zoom O ut

Press and hold IRIS Open, press and hold Focus (near or far), press Zoom Out

Focus Near (Button to right top of track ball) Diagnostic Screen Not Supported Focus Near (Button to right bottom of track ball) Debug Screen Not Supported

Zoom O ut (Button to right bottom of track ball) Preset Tours

Set Transmit Polarity Not Supported

Press Menu. Using the trackbal l scroll to "Reset Dome", press Zoom

Internal dome tours are programmed using the menu system. To run a tour enter 80-87 and press "View". The AD keypad also supports program ming tours that are stored in the AD keypad. The dome will respond to these tours. To program the AD keypad tours press Menu. Use the trackball to scroll to Define Sequence, press Focus or Zoom to enter. Now use the trackball to program sequence.

Two P atterns mapped to our preset 88 and

89. P atterns can be stored through the menu syste m or thr ough the keypad. To program through the keypad press menu, use the trackball to scroll to Record Pattern, press Focus or Zoom to select, enter number of pattern to program. Move the dome to record the desired pattern. Press Next to store. To run pattern select 1 for autotour 88 and 2 for

Zoom In

Camera Off Not Supported Night Mode- Manual Not Supported

Camera On Not Supported Alarms

Autopan Not Supported

Autoiris

Lens Speed Not Supported

Auxs

Presets Pan and Tilt Lockout Not Supported

Focus Near (Button to right top of track ball) Auto Tour

Alarm

Acknowledge Press Open or Close to put Iris in manual mode. Press Close and Open together to return to Autoiris.

Supports only a latching relay. Press <1> Output On to engage - Press <1> Output Off to disengage Presets 1-79 - To store a preset - Press Menu. Using the trackball scroll through the keypad menu to "Setup View", press Focus or Zoom to select, enter preset number, press Focus or Zoom to select. To recall a preset enter the preset number and press View.

Turbo (Set speed

to full) - (Pelco

Feature) Not Supported

Flip (Turn 180

degrees) Press Flip

Peel (Sensormatic

Feature) Not Supported

Camera Control

Including Adjust

V-Phase Menu system

autotour 89. Press Pattern to run once or Repeat Pattern to repeat.

Vicon Menu Alarms are not used. Alarms are always enabled. The dome will report to the AD keypad w hich alarm is activated (1-4) and the AD keypad controls alarm action. Alarm titles are disabled. The protocol does not support an alarm acknow ledge command. The AD keypad does respond to the dome alarm.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 9BCompetitive Protocols • 55

Kalatel

Function Keypress Function Keypress

Press Set until "Enter Programming Code" appears. Enter Access Code 951followed by SEQ. Select 4 - Cyberdome. Enter three digit camera number. Enter 1 when prompted

Enter Menu

Select/Store Set key Program Sectors

"Does The Monitor Display Site XXX". Program the unit using the joystick. Set Transmit Polarity Not Supported

Not Supported; privacy masks through the menu system is supported

Backup/Abort/Exit

Iris Open

Iris Close

Focus Near

Focus Far

Zoom Out Zoom Out Preset Tours

Zoom In Zoom In Auto Tour

Camera Off

Camera On

Autopan

"1st key" (backs up one menu) or "Hold SEQ (3 sec) to Exit" (exits entire menu system) Reset Dome Not Supported

Iris Open - Controls autoiris setting (Dome must be set for keypad, autoiris adjust enabled) Set AP limits

Iris Close - Controls autoiris setting (Dome must be set for keypad, autoiris adjust enabled) Set Pan limits Not Supported

Focus Near (Auto Focus key sets dome back to auto focus) Diagnostic Screen Not Supported

Focus Far (Auto Focus key sets dome back to auto focus) Debug Screen Not Supported

Tested using a terminal program. The KTD404 does not support this command. Night Mode- Manual

Tested using a terminal program. The KTD404 does not support this command. Alarms

Auto (AP limits set using presets 62 and 63 from menu system) Alarm Acknowledge Not Supported

Set presets 62 (left) and 63 (right) using the menu system

Internal preset tours 80 and 81 mapped to tours 3 and 4. Tours are programmed using the menu system. To execute a tour press "Set" followed by "Auto". Enter 3 or 4.

Internal dome auto tours 88-89 mapped to tours 1 and 2. Tours are programmed using the menu system. To execute a tour press "Set" followed by "Auto". Enter 1 or 2

Tested using a terminal program. The KTD-404 does not support this command.

Programmed through the menu system. Kalatel keypads do not support alarms or alarm acknowledge from a dome; alarms must be acknowledge from within the dome.

Autoiris No Control - Unit is always in autoiris

Lens Speed Not Supported

Open button on the keypad turns AUX off. Closed button turns AUX on. If set to

Auxs

Presets

Pan nd Tilt Lockout Not Supporteda

momentary pressing closed turns AUX on releasing Close turns AUX off.

Presets 000-063. Preset 000 not supported. Presets 1-063 programmed using menu system. The VFT also supports preset s tore but the KTD-404 does not support this command. The store command was tested using a terminal program.

56 • 9BCompetitive Protocols XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Turbo (Set speed to full) - (Pelco Feature) Not Supported

Flip (Turn 180 degrees)

Peel (Sensormatic Feature) Not Supported

Camera Control Including Adjust V-Phase Menu system

Tested using a terminal program. The KTD-404 does not support this command.

Ultrak When changing SurveyorVFT software addresses, the keypad may not respond to all 256 addresses. The

workaround is to go to Ultrak KEGS Setup menu, option (3.1.2) and set every camera (256) to KD6.

Function Keypress Function Keypress

Enter SVFT-M address on keypad and hit Enter key. Use LCD sof t keys to navigate to Main Menu. Use Focus Far to select and save, Iris Close to abort and exit, J oy s tick up and down to

Enter Menu

Select/Store

Backup/Abort/Exit Iris Open Iris Close Focus Near Focus Far

navigate, button 1 f o r A UX1, but ton 2 for AUX2

When in SVF T -M P reset 94 menu use Focus Far Program Sectors

When in SVF T - M Pr es et 94 menu use Iris Clos e Iris Open

Iris Close Focus Near Focus Far

Set Transmi t Polarity Not supported

Reset Dome Not supported Set AP limits Set Pan limits Diagnostic Sc re en Debug Screen

To Program sectors go to soft key me nu and select Sector Menu. It will enter SVFT-M Pr es et 96 menu. Use button 1 for AUX 2 and button 2 for AUX3, Focus Far to select and save and Iris Close to abort and exit.

Not supported Not supported Not supported Not supported

Internal dome t ou rs are pro gra mmed using SVFT M Preset 94 menu system. To run tours 80 through 87, go to Ultak soft key menu and sel ect Vector/ Run opt ion . O nce prompted to enter vector number, use number 0 to call tour 80, 1 t o

Zoom Out Twist joystick counterclockwise Preset Tours

Zoom In Twist joystick clockwise Auto Tour

Camera Off Not supported Night Mode- Manual

Camera On Not supporte d Alarms Autopan

Autoiris Use Auto I ri s soft menu key on the ke ypa d Flip (Turn 180 degrees) Not supported

Lens Speed Not supporte d

Auxs Not supported

Presets Pan and Tilt Lockout Not supported

Not supported

Presets 1-64 only are s u pported. Presets are captured and configured using SVFT-M Preset 94 menu. To recall a pres e t en ter preset number on keypad and hit V i ew but ton.

Alarm Acknowledge

Camera Control Including Adjust V-Phase Menu system

Backlight Compensation

call tour 81…, and 7 to call tour 87. Hit Enter.

Internal dome autotours are programmed us i n g SVFT-M Preset 94 menu system. To run autotours 88 and 89, go to Ultrak soft key menu and select Tour/ Run option. Once prompted to enter tour number, use number 1 to call tour 88 and 2 to call tour 89 . Hit Enter.

Night mode is en abl ed or di sabled by using Night mode soft ke y button. All other Night m o de features are acc essible using SVFT-M Preset 94 menu.

If the user wants t o use the alarms they must be acknowledged from within the dome.

Not supported

Use Auxiliary button. I n ord er t o work it needs to be enabled in SVFT-M Preset 94 menu.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 9BCompetitive Protocols • 57

Panasonic

Function Keypress Function Keypress

Press and hold CAMERA SETUP b utton for 2 sec. Use SET button to select and save options. Use ESC button to abort or leave opt ions. Move joystick up and down to select and highlight SurveyorVFT preset 94 menu options. Use button AUX 1 for Aux 1 and AUX 2 for Aux 2.

Enter Menu

Select/Store

Backup/Abort/Exit Iris Open SHIFT key + IRIS OPEN key Set AP limits Not supported Iris Close SHIFT k ey + IRIS CLOSE key Set Pan limits Not supported Focus Near NEAR key Diagnostic Screen Not supported Focus Far FAR key Debug Screen Not supported

Zoom Out WIDE key Preset Tours

Zoom In Camera Off Not supported Night Mode- Manual Not supported

Camera On Not supported Alarms Autopan Press AUTO button Alarm Acknowledge Not supported

Panasonic keypad supports communication with one dome at a time. Set Transmit Polarity Not supported

SET button when in SureyorVFT prese t 94 menu Program Sectors Not supported

Use ESC key to leave or abort any of the SureyorVFT preset 94 submenus. To quit SureyorVFT preset 94 main menu Press and hold CAMERA SETUP button for 2 sec . Reset Dome Not supported

Internal dome tours are prog rammed using SureyorVFT preset 94 menu system. The keypad does not support recalling tours.

TELE Key. To zoom in using digital zoom, first press and hold TELE key to reach the end of optical zoom and then press TELE key again to switch to digital zoom. Auto Tour

Supports autotor 88 only. To c all autotour press PATROL PLAY.

If the user wants to use the alarms they must be acknowledged from within the dom e. Panasonic protocol uses separate c ommunication interface for alarms.

Autoiris Not supported Flip (Turn 180 degrees) Not supported

Camera Control

Lens Speed Not s up ported

Auxs Not supported

Presets 1-64 only are supported. Presets are captured and configured us ing SureyorVFT preset 94 menu. To ca ll back a preset enter preset number on keypad and hit PRESET

Presets Pan and Tilt Lockout Not supported

button.

Including Adjust V-Phase Not supported

Home Button. Pressing this button moves the dome to saved preset position.

58 • 9BCompetitive Protocols XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Philips

Function Keypress Function Keypress

Use On-46-Enter shortcut to enter Dome menu.

Use Focus Far button to select and save

options. Use Iris Close button to abort or leave

options. Move joystick up and down to select

and highlight Dome menu options (joystick

does not support "press and hold" navigation

and editing when in Dome menu). Use shortcut

Set-1021-ENTER for Aux 1, use Set-1022-

ENTER for Aux 2 and us e Set-1023-ENTER for

Aux3. Note: In order for the shortcut to work, the

Enter Menu

Select/Store Backup/Abort/Exit

Iris Open Iris Close Focus Near Focus Far

Zoom Out

Zoom In Camera Off

Camera On

Autopan

Autoiris

Lens Speed

Auxs

Presets

Pan and Tilt Lo ckout

keypad must be unlocked. To unlock, use Off-

Twist joystick CW. To zoom in using digital

zoom turn joystick CW again after reaching the

Use On-2-Enter shortcut. To set Autopan Left

and Right limits use Set-101-Enter and Set-102-

Use On-3-Enter shortcut. Use Iris Open or Iris

Close buttons to switch back to manual iris

To save presets use either Set-1-Enter through Set-79-Enter shortcuts or Dome menu. To recall

presets use Shot-1-Enter to Shot-79-Enter

90-Enter unlock menu.

Focus Far button

Iris Close button

Iris Open Iris Close

Focus Near

Focus Far

Twist joystick CCW

end of analog zoom spectrum.

Not Supported

Enter shortcuts respectively.

Not Supported

shortcuts. All 79 presets are supported.

Not Supported

Set Transmit Polarity

Program Sectors Reset Dome

Set AP limits Set Pan limits Diagnostic Screen

Debug Screen

Preset Tours

Auto Tour Night Mode- Manual

Alarms

Alarm Acknowledge

Flip (Turn 180 degrees) Camera Control

Including Adjust V-Phase

Supported. Use Dome menu to enable sector

blanking. Use O n -86-Enter to assign se ctors

(use Set-1022-Enter for Aux 2 and use Set-1023-

To set Left limit use Set-101-Enter and to set

Right limit use Set-102-Enter.

To save tours use either Set-80-Enter through

Set-87-Enter shortcuts or Dome menu. To recall

presets use Shot-80-Enter through Shot-87-

Enter shortcuts. All 7 tours are supported.

Record auto tour 88 use On-100-Enter, Record auto tour 89 use On-101-Enter, Playback 88 auto tour On-51-Enter, Playback auto tour 89 On-53Enter, Continuous Playback auto tour 89 use On52-Enter and Contin uous Playback auto tou r 88 use On-50-Enter. Also, auto tours can be saved using Dome menu.

If the user wants to use the alarms they must be

acknowledged from within the dome (auto

Auto acknowledge is only supported

To call Factory Home Position use Set-110-

Enter. To save home position preset use Dome

NOTE: Dome "PTZ timeou t" menu feature is

not enabled due to Philips protocol PTZ

control delay limitation.

Not Supported

Enter for Aux3).

Set-97-Enter

Not Supported Not Supported Not Supported

Not Supported

acknowledge).

N/A

menu.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 9BCompetitive Protocols • 59

Cohu

Function Keypress Function Keypress

To launch Dome menu use P reset 64 + Store.

Use Focus Far button to select and save

options. Use Iris Clos e button to abort or exit

options. Move mouse curs o r u p and down on

Enter Menu

Select/Store Backup/Abort/Exit Iris Open Iris Close Focus Near Focus Far Zoom Out

Zoom In Camera Off

Camera On

Autopan

Autoiris

Lens Speed Auxs

Pan/Tilt pane to select and highlight Dome

AUX 1 is Preset1 + Store, AUX 2 is Preset2 +

Store, and AUX3 is Preset3 + Store.

Lens Fast button. Sets dome to "Hi" lens speed.

menu options.

Focus Far button

Iris Close button

Iris Open Iris Close

Focus Near

Focus Far Zoom Out

Zoom In

Camera Power button

Not Supported

Set Transmit Polarity

Program Sectors Reset Dome Set AP limits Set Pan limits Diagnostic Screen Debug Screen Preset Tours

Auto Tour Night Mode- Manual

Alarms

Alarm Acknowledge

Flip (Turn 180 degrees) Camera Control

Including Adjust V-Phase

Select Preset 63 and press Store button. AUX 2 is Preset2 + Store and AUX3 is Preset3 + St ore.

Use Focus Far button to save sector selection

To save tours use Dome menu

Not Supported. Cohu does not support

If the user wants to use the alarms they must be

acknowledged from within the dome (auto

Auto acknowledge is the only one supported

Not Supported

and go to next. Not Supported Not Supported Not Supported Not Supported Not Supported

AutoTours.

Not Supported

acknowledge).

N/A

To save presets use either WinMPC software or

Dome menu. In WinMPC, to save a preset

select Preset (1-62) and press Store button. To

call back a preset select Preset (1-62) and

press GoTo button. Note, preset PTZ position

Presets

cannot be saved to Preset 63 and P reset 64.

60 • 9BCompetitive Protocols XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Maintenance

The SurveyorVFT requires no scheduled maintenance; however, the Lower Domes require occasional cleaning. The Chrome and Gold Domes are referred to as Metallized type domes. The Clear and Smoked Domes are referred to as Acrylic type domes. All domes require careful handling and occasional cleaning.

Care and Cleaning of Metallized Domes

1. Always handle the lower dome by the flange and avoid touching the inside surface, as acid in a fingerprint can etch the internal coating. Use the recommended cleaning procedure in Step 4.

2. If dust or dirt accumulates in the lower dome's interior, remove it with clean, dry pressurized air.

3. If spots, streaks or stains appear on the interior, they can be removed by rinsing with clean water and drying with clean, dry pressurized air. Do not rub the inner surface.

CAUTION: Rubbing the inner surface of metallized lower domes can cause permanent scratches that may

render the dome unusable.

4. If cleaning of the inner surface is necessary, use a wick. Make a wick by rolling a section of soft microwave-safe (aluminum free) paper towel into a tightly wound tube and tear it in half. Moisten the torn edge of the wick with an approximate solution of 50% isopropyl alcohol and 50% water. Hold the Lower Dome upside down and gently wipe the inner surface from the inside to the outer edge. Use a new wick for each 2 passes over the dome.

5. Clean the lower dome's exterior with any soft, nonabrasive cleaning cloth and a cleaning agent suitable for acrylic plastic. Either liquid or spray cleaner (wax suitable for fine furniture) is acceptable.

Care and Cleaning of Smoked and Clear Acrylic Domes

1. Always handle the lower dome by the flange and avoid touching the inside surface.

2. If dust or dirt accumulates in the lower dome's interior, remove it with clean, dry pressurized air.

3. If spots, streaks or stains appear on the interior or exterior, they may be removed with an approximate solution of 50% isopropyl alcohol and 50% water using a soft microwave-safe (aluminum free) paper towel. Dry with clean, dry pressurized air.

4. Scratches or surface blemishes on the interior or exterior may be removed with a nonabrasive wax using a nonabrasive cleaning cloth. Either liquid or spray cleaner (wax suitable for fine furniture) is acceptable.

CAUTION: Excessive rubbing of the lower dome surface can cause permanent scratches that may render

the dome unusable.

5. Clean all surfaces with any soft, nonabrasive cleaning cloth and a cleaning agent suitable for acrylic plastic.

Fuse Replacement

Two fuses (F1 and F2) are located on the underside of the customer interface board. Refer to Figure 29. When necessary, replace them with the following fuse values:

F1: 5 x 20 mm, 1.6 amp, 250 volt, slo-blo F2: 5 x 20 mm, 2.5 amp, 250 volt, slo-blo

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 10BMaintenance • 61

Shipping Instructions

Use the following procedure when returning a unit to the factory:

1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A.

Vicon Industries Inc. 89 Arkay Drive Hauppauge, NY 11788 Phone: 631-952-CCTV (2288); Toll-Free: 1-800-645-9116; Fax: 631-951-CCTV (2288)

For service or returns from countries in Europe, contact: Vicon Europe Ltd.

Brunel Way Fareham, PO15 5TX United Kingdom Phone: +44 (0) 1489 566300; Fax: +44 (0)1489 566322

2. Attach a sheet of paper to the unit with the following information:

a. Name and address of the company returning the unit b. Name of the Vicon employee who issued the R.A. c. R. A. number d. Brief description of the installation e. Complete description of the problem and circumstances under which it occurs f. Unit’s original date of purchase, if still under warranty

3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection.

Mark the R.A. number on the outside of the carton on the shipping label.

62 • 11BShipping Instructions XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Reference

Coaxial Cable Recommendations

Caution: Careful selection of proper cable is essential to obtain the best performance from this equipment. Vicon assumes no responsibility for poor performance when cables other than those recommended, or equivalent, are installed. In all cases, coaxial cable impedance should be 75 ohms.

Materials

Use only a pure copper center conductor. Do not use a copper-plated steel or aluminum center conductor, as they will result in poor quality video. Solid-core bare copper conductor is the best type, where flexing and bending will be minimal. If severe bending and flexing is required for installation, use a stranded center conductor. Never exceed the manufacturer’s minimum bend radius specification. Use cellular (foam) polyethylene dielectric except where heavy moisture exists. For moisture conditions, use solid polyethylene dielectric cable with a heavy exterior insulation. The shield must be copper braid providing 95% or better coverage.

Cable Types

The cable types listed below are the most common 75-ohm types used. They vary in size (diameter), dielectric type and net DC resistance. The larger cable results in a lower DC resistance and better video quality, with increased difficulty in handling and installation. Let the required picture quality and cable distance provide a guide in choosing the best cable type. For cables other than the approved Vicon types below, contact the manufacturers listed below. Note that “BC” refers to bare copper and “TC” refers to tinned copper.

Recommended Coaxial Cable Types

Cable

Type

RG-11/U 8213 9847 811,4811 14 Solid BC BC braid (95%) 2.6 (8.5) RG-6/U 9248 9804C 806,4806 18 Solid BC Foil + 61% TC braid (100%) 7.5 (24.6) RG-59/U 8281* ---- 815 20 Solid BC 2 TC braids (96%) 9.9 (32.5) RG-59/U 9259 9803 816 22 Stranded BC BC braid (95%) 15.0 (49) RG-59/U 9659 ---- ---- 22 Stranded BC BC braid (95%) 15.0 (49)

*Requires special BNC-M connector due to 0.305 nominal O.D. Belden Inc. http://www.belden.com/ (800) 235-3361 Alpha Wire Company http://www.alphawire.com/ (800)-52 ALPHA (522-5742) West Penn Wire http://www.westpenn-cdt.com/ (800)-245-4964

** For longer cable runs, use a Vicon Video Amplifier to obtain a suitable picture.

Belden

Type No.

Alpha

Type No.

West Penn

Type No.

Type Center

Conductor

Type Shield and

% Coverage

DC Resistance

ohms/1000 ft (km)

Picture Quality vs. Cable Length

Picture Quality

Maximum Cable Run** ft (m)

RG-59/U RG-6/U RG-11/U

Usable picture 1100 (350) 1500 (450) 2400 (750) Clean picture 820 (250) 1000 (300) 1600 (500) Best picture 400 (120) 530 (160) 820 (250)

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 12BReference • 63

(

)

(

Twisted-Pair Cable

CAUTION: Careful selection of the proper cable is essential to obtain the best performance from this

equipment. Vicon assumes no responsibility for poor performance when cables other than those recommended are installed.

tMa erials

Use a pure copper stranded conductor with or without a tin plating to obtain a low DC resistance. Do not use cable with

ither a steel or an aluminum stranded conductor because these do not transfer signals effectivelye

referred insulation and cable jacket is Polyvinyl chloride (PVC). It has better electrical characteristics than polyethylene

and resists flames, sunlight and most solvents, but is more vulnerable to moisture.

Cable Types

The most commonly used cable types are dual individually-shielded, twisted pa the most convenient for RS-422/ RS485 applications. Single twisted pair is also a suitable cable.

Cho

ose a Belden cable type by referring to the characteristics and maximum distances listed below. The maximum distance for the most reliable digital control refers to the distance between the CPU/Keypad and the Camera Dome Assembly. The characteristics of the cables in Table 6 should be used as a guideline when cables other than Belden are used. Materials and construction must follow the guidelines above.

CABLE

TYPE

Belden 9406 Belden 9402 Belden 8723

lden 8162Be

Belden 9729

e1B lden 9182

Datalene is a Registered Trademark of Belden. Belden Inc. http://www.belden.com/

WIRE SIZE

AWG

22 PVC PVC 5000 (1500) 20 PVC PVC 5000 (1500) 22 Polypropylene PVC 8000 (2400) 24 Datalene¹ PVC 15000 (4600) 24 Datalene¹ PVC 15000 (4600) 22 Datalene¹ PVC 25000 (7600)

INSULATION

MATERIAL

JACKET

MATERIAL

Table

Recommended Individually-Shielded, Twisted-Pair Cable Types

ir in a single jacket. This configuration is

DISTAN CE ft (m)

max.

UTP Connection

For NVT models, where video is transmitted over twisted-pair cable, a UTP receiver is required. Vicon offers t receivers to provide video transmission over a range

NVT Receiver Wire Gauge

(AWG)

V212-NVT 24-16 2, 3, 4, 5 or better 500 (152) V213-NVT 24-16 2, 3, 4, 5 or better 1000 (304)

V6 24-16 2, 3, 4, 5 or better 3000 (915)* 52R-NVT

*Video signals traveling in opposite directions may co-exist in the same wire bundle up to 2000 ft (600 m) if Cat-5 wire is used.

Oper

ating Distances for UTP Installations

of distances.

Category Type Distance

Table

for long distances. The

NUMBER OF

TWISTED PAIRS

2 2 2 2 2

800) 235-3361

hree

ft (m)

1.5-inch Pipe Design

The standard “1.5-inch pipe” referred to in this manual has actual dimensions of:

Outside diameter: 1.9 inches (48.3 mm). Inside diameter: 1.61 inches (40.9 mm).

64 • 12BReference XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

ation

mm) minimum (ANSI “standard” grade thickness). Wall thickness: 0.145 inches (3.37

Network Cable

Caution: Careful selection of proper cable is essential to obtain the best performance. Vicon assumes no responsibility for poor

performance when cables other than the recommended types, or equivalent, are used.

Materials

ure copper stranded con

Use p ductors to obtain a low DC resistance. The preferred insulation and cable jacket is Polyvinyl chlori lectrical characteristics than Polyethylene and resists flames, sunlight and most solvents, but is more vulnerable to moisture.

C le Types

The m hese category cables are best suited for Ethernet

ost commonly used cable types are CAT5, CAT5e and CAT6. T

etwork applications.

n Choo able type by referring to the characteristics listed below. The Table below should be used as a

se a Belden c

guide an Belden are used. Materials and construction must follow the guidelines above.

line when cables other th

C ORY BANDWIDTH

ABLE TYPE WIRE SIZE

Belden 1624P Belden 1583

Belden 1585A Belden 7883

Belden Inc. http://www.belden.com/ (800) 235-3361

etter ede (PVC). It has b

INSULATION

(AWG)

24 24 Polyolefin PVC 5e 100 328/100 4

24 24 Polyolefin PVC 6 250 328/100

MATERIAL

Fluorinated

Ethylene

Propylene

Fluorinated

Ethylene

Propylene

JACKET

MATERIAL

Low Smoke

PVC

PVC 5e 100 328/100

CATEG

(MHz)

5 100 246/75

MAXIMUM

DISTANCE

(ft/m)

NUMBER OF

Table

Recommended Network Ca

ble Types

TWISTED

PAIRS

4 4

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 12BReference • 65

Technical Information

ELECTRICAL

Camera Types:

Input Voltage:

Maximum Power

Cable Distance: Current

(@24 VAC), max:

Power Consumption:

e alent:

H at Equiv

andard Connector

Video Output

Emission Rating:

OPERATIONAL

ideo Pan View:

ideo Tilt View:

Autopan Speed:

Drive Type:

Ratings

Types:

Impedance:

Fuse:

Radio

Pan Speed:

Tilt Speed:

Electrical motorized pan and tilt with electronic control.

Units available in color and day/night (NTSC/PAL) formats and a variety o zoom and feature capabilities.

18-30 VAC. (Will operate within spec on voltages up to 32 VAC. Fo voltages between 30-32 VAC, a Class 3 indoor/dry or outdoor/wet power supply with appropriate wiring methods in accordance with the National Electrical Code ANSI/NFPA 70, State and Local wiring codes must be used.)

See Table 4.

Indoor:

Coax, Fiber, UTP: 1.0 A. ViconNet (TCP/IP): 1.4 A.

Outdoor:

Coax, Fiber, UTP: 1.8 A. ViconNet (TCP/IP): 2.3 A.

Indoor:

Coax, Fiber, UTP: 24 W. ViconNet (TCP/IP

Outdoor:

oax, Fibe

C r, UT ViconNet (TC

Indoor:

Coax, Fib

4 kg-c

(0.3

Net (TCP btu/min

Vicon

-cal/mi

(0.49 kg

doo

Out

, Fiber, UTP: 2.8 btu/min

Coax (0.6 kg-cal/min). ViconNet (TCP/IP): 3.1 btu/min (0.

77 kg-cal/min).

te: These figures represent the

nversion of 100% of the electrical energy to heat. Actual percentage o heat generated will vary from product to pr figures are provided a determining the extent of cooling required for an installation.

Video Out: See version type. Power: 2-position removable screw terminal block. Control Input/Output: See version

type.

Relay Output: See version type. Alarm Input: 8-position removable

screw terminal block. 75 ohms.

F1: 5x20 mm, 1.6 A 250 VAC slo-blo. F2: 5x20 mm, 2.5 A 250 VAC slo-blo.

FCC Class A.

360°.

-2.5° (-2.5° above horizon) to

92.5° (-2.5° past vertical). Variable, 0.1 to 360°/sec

(120°/sec in 22X). Variable, 0.1 to 42°/sec;

enable/disable. Variable, 0.1 to 150°/sec

(90°/sec in 22X).

): 34 W.

P: 50 W.

P): 54 W.

P/I

er, U

TP: 1.3 btu/min

al/mi

n).

/IP): 1.9

n).

be less and will

oduct. These

s an aid in

Zoom and Foc

Preset Capabilities:

Autotour Capabilities:

us Speed:

Sectoring:

Preset Solving

Speed:

Preset Accuracy:

Tour Capabilities:

larm Capabilitie

Relay Outp

Capabilitie

Control D y:

ispla

Privacy Masks:

Screen Titling

Capabilities:

Less than 1.8 sec from end to end. 16 max, programmable for size and

titling; capability to be blanked out (22XEX/23X/35X only).

79 individual programmable preset positions.

1 sec nominal.

0.1 degrees maximum in pan and tilt.

22X: 4 tours available. 22XEX/23X/35X: 8 tours available. 32 programmable events per tour. Events may be preset positions with speed control, alarm acknowledge, dwelltime control, relay control, call autotours, tour repeat or another tour, save/recall camera status.

22XEX/23X/35X: 2 autotours available with 256 pan, tilt and zoom functions per autotour. Programming is done in real time with joystick and push buttons.

utotours not available on 22X

model.

4 alarm inp y prog Functional state ena Report state (report

ctive st Mod auto time

uts, individuall

rammable.

ble/disabl on/off).

ate (high/low).

e (m

anual, momentary or

matic) with programmable

control. Set and reset action (preset solve, relay on/off, tour, autotour).

larm titling.

1 relay output.

Power-on state definition (on/off). Output type definition (momentary o latching).

Resistive

on status Relay functi

titling.

Load: 1 C

.5A@30 VD (max). Inductive Loa .75 A @30 VDC.

allowing ful

d: 0

, mOn-screen

enu

l config

-driven system uration of the

dome. 22XEX/23X/35X: 16 individual,

programmable, zoom-scalable. Programmable for camera, preset,

sector, relay and alarms. Camera: 1 for each. Preset: 79 maximum. Sector: 16 maximum (not on 22X).

larm: 4 maximum. Individual type date and time enable/disable; 20 characters maximum. Selectable position. Three text sizes for top two lines. Fade capability. Compass/azimuth, 8 compass headings (N, NE, E, SE, S, SW, W, NW). Not available on 22X.

dwell

66 • 13BTechnical Information XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Scheduling:

Multilanguage Menu:

Day/Night (2

3X) Features:

Auto Baud:

Absolute Position Control:

Competitive Protocols:

COAXIAL/UTP VERSION

Control Protocol

Hardware:

Control Protocol

Software:

Control Protocol

Format (selectable via

DIP switch 2; see Note on

Competitive Protocols):

Real time clock allows scheduling of up to 64 event relays, alarms, to on 22X).

English, Spanish, French, German and Italian.

6 programmable motion detec zones with 3 sensitivity levels; im freeze during preset solve; flip (invert) video image.

uto baud detection in RS-422/ RS485 mode; 4800, 9600, 19,200 bps baud rates supported.

vailable in RS-422/RS-485 mode. Pan/tilt: 0.125°; zoom: 0.125X.

DIP switch selectable. (Not available on ViconNet version.)

Vicon: Vicon’s Pilot and NOVA Control Systems and V1300X-RVC desk-top keypad or V1300X-RVC rack-mounted keypad; NTCIP 1103 compatible hardware.

s, including presets,

urs or autotours (not

Surveyor Direct Control program runs on a standard PC type computer with an RS422/485 half duplex protocol interface.

Vicon: RS-422 or RS-485 protocol. Communication is simplex or hal duplex operation at 4800, 9600 o 19,200 baud or Vicon’s enhanced VicoaxII protocol (superimposed data

automatically detected upon powe up. RS-485 protocol utilizes full tri-state outputs for daisy chain capability. Pelco: Pelco D Protocol (3/2/99); RS485 N.8.1, simplex 2400 bps, duplex 4800 bps. Sensormatic/AD: RS-422/RS-485 communication protocols user’s guide Rev. A (csd 05/00); RS422/RS-485 bps. May require RS-422 converter, RCSN422. Ultrak: KD6, KD6 rotocols; RS-485 simplex E.8.1, 9600 bps. Philips: Receiver o Dome control code proto

duplex N.8.1 4800

-Z control p /Driver/Aut

col;

tion age

gnal)on composite video si

RS-232 simplex N.8.1, 2400 or 9600 bps. Kalatel: Non-repeating transm comman

ds; RS-422 simplex N.8.1,

s. 9600 bp Cohu: MPC System RS-4 interface; RS-422 duplex N.8.1, 96

00 bps. Panasonic: Panasonic conventional and new camera protocol

Note: A

ll companies make changes and improvements in their products. Because

this pr

oduct can interface with equipment not manufactured by Vicon, there is a

possibi

lity that the interface protocols may have changed since Vicon tested this product with the interfacing equipment. Vicon recommends purchasing a single unit for bench testing prior to purchasing and installing this product in quantity.

Connector Types:

OPTICVERSIO

FIBE

Fiber Optic Receiver

Specs:

Connector Types:

VICONNET VERSIO

Video Formats Supported:

Video Transmission Rate:

Communication

Hardware:

LAN Interface:

Number of Video

Channels:

Audio:

Alarm

Number of Simultaneous

Video Streams:

ideo Transmission

Resolutio

Video Quality

Video Bandwidth:

Connector Type:

Video Out:

Coax: BNC-F. UTP: 3-position removable screw terminal block.

Control Input/Output:

8-position removable screw terminal block. Relay Output: 8-position removable screw terminal block.

Video:

I/O Level: 1 V p-p. I/O Impedance: 75 ohms. Bandwidth: 8 MHz. Differential Gain: 5%. Differential Phase: 5º. SNR: 60 dB.

Data:

Data Rate: Up to 19.2 Kbps.

Optical:

Wavelengt

h: 850/1300 nm. Loss Budget (62.5/125 u): 12 dB. Fiber: Single multimode.

Video Out: ST type. Control Input/Output: ST type. Relay Output: 8-position removable

screw terminal block.

ViconNet Digital Video Management System.

100 Mbps, TCP/IP Unicast.

1, over LAN connection. 1 line-level microphone input, 0 dbm,

32 KHz bandwidth, 600 ohm impedance,2 V RMS (1 V p-p) output.

4 in, NO/NC (through SurveyorVFT

puts); 1 relay out.

in NTSC and PAL, model dependant. 1 channel @

(25 fps, PAL), maximum.

Maximum of 10 viewing/recording streams per camera dome.

480 horizontal TV lines maximum at 720 x 4 (863 x 586, P

ViconNet ality 1-8,

selectabl bar with 2 compres tings in resolutio 3 x 586,

360 x 244 (432 x 293, PAL), 122 (432 x 146, PAL).

1.7 Mbps (per video stream), nom. Network: Ethernet 100Base-T RJ-45

ack. 10/100 Mbps required for

udio: 1/8-in. (3.5 mm) mono jack.

30 frames per second

88 t pixel palle

AL).

software qu e on a 4-position sion level set

ns 720 x 488 (86

20 x 244 (863 x 2PAL), 7 93

ork connection. netw

, PAL),

360 x

Note: Pelco is a registered trademark of Pelco. Sensormatic is a registered trademark of Tyco International Limited. Philips/Bosch is a trademark of Koninklijke Philips Electronics N.V. Kalatel is a trademark of GE Interlogix. Ultrak is a trademark of Honeywell Inc. Cohu is a trademark of Cohu, Inc.

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 13BTechnical Information • 67

Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd.

CAMERA/LEN

Specifications:

VIDEO TRANSMISSIO

SOFTWARE OPERATIO

Maximum Distances:

Network Se

tup:

Site Authorization:

Macro Create & Edit:

Alarm Setup:

Authentication:

Picture Qu d FPS

ality an

Priority:

MECHANICAL

Application:

Mounting:

Housing Types:

Pendant Mount

Size/Thread:

Refer to Table 5.

Coax: 1100 ft (350 m), cable dependant. Vicoax: 1500 ft up to 140ºF (60ºC); 1000 ft up to 165ºF (74ºC) UTP: up to 3000 ft (915 m), model dependant. Fiber: 1 mile min.; longer distances available dependant on cable quality. ViconNet: 100 meters without repeater.

Standard network protocol type using IP addressing scheme and separate PC application software. Allows setting of Daylight Saving Time and synchronous time across the network.

Camera dome can be setup using remote recorder or workstation GUI. Permissions can be assigned fo macro create & edit, alarm setup,

uthentication, Reports and System

Supports up to 20 Groups

Status. and 100 Users.

System macros can be added, edited and deleted using the dome’s video sensor input. In addition, within macros, alarms can be sent and remote macros run.

n alarm can be triggered on video motion detection and loss. The alarm can be sent to remote units.

The video from the camera dome is set to view the Authentication status symbol on the displayed video.

System can be setup to prioritize recorded picture quality and video FPS. Priority ca user/macro reco

n be assigned to

rding, autorecord o prealarm recorded video. Also, simultaneous use of PTZ control on the camera dome can be enabled.

Indoor or outdoor. In-ceiling or indoor/outdoor pendant. Indoor pendant housing and outdoor

pendant housing with sunshield.

Standard 1-1/2 inch male NPT pipe thread or metric equivalent.

Lower Dome Types:

ENVIRONMENTAL

Not evaluated by UL))

(

Temperature Range:

Storage Humidity Range:

Dimensions:

Weight:

Construction:

Color:

Shipping

Dimensions:

Shipping Weight:

Shipping Volume:

Operating

Humidity Range:

Storage

IP Rating:

Rain/Wind:

Units available for indoor or outdoo in a variety of colors. See Table 1.

Ceiling

Indoor

Diameter: 7.1 in. (180 mm). Height: 9.7 in. (246 mm).

Indoor Pendant

Diameter: 8.0 in. (203 mm). Height: 10.0 in. (254 mm).

Outdoor Pendant

Diameter: 9.0 in. (228 mm). Height: 10.3 in. (262 mm).

Lower Dome

Diameter: 5.9 in. (150 mm). Indoor Ceiling: 5.1 lb (2.3 kg).

Indoor Pendant: 4.7 lb (2.1 kg). Outdoor Pendant: 7.7 lb (3.5 kg).

In-ceiling: Black anodized aluminum. Indoor pendant: molded plastic. Outdoor pendant: die-cast aluminum with molded plastic sunshield.

Off-white housing and sunshield.

Height: 11.6 in. (294 mm). Width: 16.1 in. (409 mm). Depth: 19.9 in. (505 mm).

In-Ceiling: 8.9 lb (4.0 kg). Indoor Pendant: 8.5 lb (3.9 kg). Outdoor Pendant: 11.3 lb (5.1 kg).

2.2 ft3 (0.06 m3).

Indoor units: 32 to 132° F (0 to 55° C). Outdoor units:-29 to 165° F (-34 to 74° C) in accordance with NEMA 2.1.5.1 STD 2.

Indoor: 0 to 90% relative, noncondensing

Outdoor: 100% relative, noncondensing.

-40 to 150° F (-40 to 65° C). 0 to 90% relative, non-condensing. Outdoor unit IP66.

Indoor Pendant: IP52. In-Ceiling: IP51.

Outdoor: heavy rain up to 4 in./hr at winds up to 90 mph, when mounted on standard Vicon wall

mount.

Wire Size

(AWG)

Annealed

Copper Wire

Coax, Fiber,

24 VAC 28 VAC 24 VAC 28 VAC

UTP

ViconNet

20 300 (91) 215 (66) 500 (152) 350 (107) 165 (65) 130 (40) 280 (85) 217 (66) 18 469 (143) 336 (102) 781 (238) 547 (167) 258 (102) 203 (62) 438 (134) 340 (104) 16 750 (229) 538 (164) 1250 (381) 875 (267) 413 (126) 325 (99) 700 (213) 544 (169) 14 1200 (366) 860 (262) 2000 (610) 1400 (427) 660 (262) 520 (159) 1120 (341) 870 (265) 12 1875 (572) 1344 (410) 3125 (953) 2188 (667) 1031 (314) 812 (248) 1750 (533) 1359 (414)

68 • 13BTechnical Information XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Indoor Outdoor

Distance ft (m)

Coax, Fiber,

UTP

ViconNet

Coax, Fiber,

UTP

ViconNet

Coax, Fiber,

UTP

ViconNet

Table 4: Maximum Power Cable Distance

Camera

Specifica

Optical Zoom

Digital Zoom

Zoom Speed

Imag

Pictur

Scanning System

Horizontal Resolution

tions

Type

Total Zoom

e Device

e Elements

Sensitivity

Table 5: Camera/Lens Specification

Model Numbers

SVFT-C22, SVFT-P22,

SVFT-W22

8701-00, 8704-00,

8707-00 8707-01

NTSC

9 sec Tele-Wide: 3.9 sec Tele-Wide: c Tele-Wide: 3. 3.9 sec Tele-Wide: 3.9 se

1 4-inch interline transfer e transfer 1/4-inch interli

2 2:1 interlace, 625 lines

40 IRE, f/1.6, auto 1/4s

CCD

768(H) x 494 (V),

380,000 pixels

:1 interlace, 525 lines

60 fields/sec

0.002 fc (0.03 lux) at

SVFT-C22C, SVFTP22C, SVFT-W22C

Product Codes

8701-01, 8704-01, 7

Formats

PAL NTSC PAL

Color or Color Color Col

iew 22X 23X 23X ExView 22X ExV

12X 12X 12X 12X

64X X 276X 264X 2 276

1/4-inch interline transfer

CCD

752(H) x 582 (V),

438,000 pixels

50 fields/sec

0.002 fc (0.03 lux) at

40 IRE, f/1.6, auto 1/3s

470 TV lines 470 TV lines olor) 470 TV lines (color) 530 TV lines (c

1/4-inch interlin

SVFT-C2SV3, SVFT-P23,

2:1 interlace,

0.0019 fc (0.0

40 IRE, f/1.6,

FT-W23

8702-00, 8 05-00,

8708-0

CCD

768(H) x 49

380,000 pi

60 field /sec 50 fields/

4 (V), 847(H) x xels 490,000 pixe

525 lines 2:1 interlace, 62

2 lux) at 0.0019 fc (0.02 lux)

auto 1/4s 40 IRE, f/1.6, auto

SVFT-C23C, SVFTP23C, SVFT-W23C

8702-01, 8705-01,

8708-01

CCD

ne transfer

2 (V),

5 lines

sec

1/5s

S/N Ratio

Synch

ronization

Automatic Gain

Control (AGC)

Backlight

Compensation

Iris Control

Wide Dynamic Range

Video Focus

hite Balance

Shutter Speed

Focal Length

Apertur

e max

Horizontal A

ngle of

View

More than 50 dB More than 50 dB More than 50 dB More than 50 dB

l/External Internal/External

Interna

(line lock on AC line) (l

Software adjustable

Automatic/Manual

1.0 m (tele ) - 0.01 m

Automatic/Manual

ed/Blue Gain Level

Auto (DSS): 1/2-1/4000

47° wide, 2.2° tel 47° wide, .2° tele 47° wide

o level baackground vide

(wide)

K sec

f/1.6 f/1. f/1.6

e 47° wide, 2.2° tele 2 , 2.2° tele

ine lock on AC line)

djustable to 32 dB Adjustable tAdjustable to 25 dB A o 30 dB Adjustable to 30 dB

Software adjustable

ckground video level

utomatic/Manual Automatic/M Automatic/Manual A anual Automatic/Manual

NA O N (Auto or Manual)NA FF/ON (Auto or Manual) OFF/O

atic/Manual

Autom

ele ) - 0.01 m

1.0 m (t

Automatic/Manual

Red/Blue Gain Level

Auto (D

Man:1Man:1/2-1/30

Lens Specifications

ide)

SS): 1/1.5-1/400

/1.5-1/30K sec

f/1.6 6

Internal/Ex

(line lock on

Software adj

background vi

Automatic/M

1.0 m (tele )

Automatic/M

Red/Blue Ga vel

0 Auto (DSS)

Man:1/2-1/

ternal AC line)

ustable Software adjustabl deo level background video l

anual

- 0.01 m

(wide e)

) (wid

anual Automatic/Manual

in Level Red/Blue Gain Le

1/2-1/60 Auto (DSS): 1/1.

0K sec Man:1/1.5-1/30

8 m 4 - 88 mm 4 - 88 mm 3.6 - 82. mm 3.6 - 82.8 m

Internal/External

(line lock on AC

Automatic/Manual

1.0 m (tele ) - 0.01 m

line)

evel

5-1/50

K sec

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 13BTechnical Information • 69

Camera

Specifications

Model Numbers

SVFT-C22CA, SVFT-P22CA, SVFT-W22CA/

SVFT-C22CA-C, SVFT-P22CA-C, SVFT-W22CA-C

Product Codes

8741-00, 8742-00, 8743-00/ 8741-01, 8742-01, 8743-01

Formats

SVFT-W35/SVFT-W35-C

910 1 2-00/9102-0

NNTSC/PAL TSC/PAL

Type

Optical Zoom

Digital Zoom

Total Zoom

oom Speed

Imag

e Device

Picture Elements

Scanning System

Sensitivity

Horizontal Res

S/N Ratio

Synchroniza

mpensation

Iris Control

Wide Dynamic Range

olution

tion

acklight

Color Color

22X 35X

12X 12X

264X 420X

O sec TelePTICAL wide/DIGITAL tele: 3.9 -Wide: 4.6 sec

1/4-inch in1/4-inch interline transfer CCD terline transfer CCD

768(H) x 494 (V), 380,000 pixels/

752(H) x 582 (V), 438,000 pixels

2:1 interlace, 525 lines 60 fields/sec 2:1 interlace, 625 lines 50 fields/sec

nes ines 470 TV li 540 TV l

n ternal (line lock on AC line) n

I ternal/Ex Internal/Exter al (line lock on AC line)

ON/OFF ON/OFF

0.005 fc (0.05 lux) at0.2 fc (2 lux) at 40 IRE, f/1.6 40 IRE, f/1.6, auto ½ s, IR ON

768(H) x 49

752(H) x 58

2:1 interlace,

More than 50 dB More than 50 dB

AutoAutomatic/Manual matic/Manual

4 (V), 380,000 pixels/

2 (V), 438,000 pixels

525 lines 60 fields/sec

, e

NN/A OFF/O (Auto or Manual)

c 2:1 interlace 625 lines 50 fields/s

EIS (Image Stabilizer)

Video Focus

White Balance

Shutter Speed

Lens Specifications

Focal Length

Aperture max

Horizontal Angle of

View

vel Automatic/Manual; Red/Blue Gain Le Automatic/Manual; Red/Blue Gain Level

1/60 - 1/4000 sec/ 1/6

1/50 - 1/4000 sec - 1/4000 sec

f/1.6 f/1.4

47.3° wide, 2.2° tele 55.8° wide, 1.72° tele

1/5

Table 5: Camera/Lens Specifications (continued)

wN/A Yes ( ith digital zoom)

oAutomatic/Manual Aut matic/Manual

- 1/4000 sec/

34 - 88 mm .4-119 mm

70 • 13BTechnical Information XX134-07-00 Rev 908 SurveyorVFT Camera Dome System

Vicon Standard E pment Warranty

Vicon Industries Inc. (the “Company”) warrants your equipment to be free from under Normal U t ail purchase for a period o

1. VCRs, all mod

2. Video monito CD monitors, all models:

3. Uninterruptib date of original retail purch

4. VDR-304, VD ries: One year from date of original retail purchase.

5. V5616MUX: n urchase.

6. S10-CH: 18 mon

5. Normal Use excl heads, and gears due

Date of retail purchas i s possession of the equip tion of the Company, the date the e al by the orig r

The sol repaired or (a ed, at Company , en authorized for return by t pment is prepaid in accordan

The Company will not be obligated to repair or replace equipment show e r damage, or to parts which in the judgment of the Comp ipment which m e ed, misused, or been subject to unauth r

Software supplied eith is furnishe ot warrant that such software shal b support v , t, may be discontinued at any m discretion. Vicon rese hanges to its software t y time and without notice.

This Warranty is in l w arranties a Goods, including any warranty of e remedy spe ty is in lieu of all other remedies available

No half of the Com a connection with the sale of any G above. In no event w C indirect, special, incidental, consequen a r arising from interrupted loss of data, replacement of equipm ndertaken by the Purchaser

This warranty applies or its dealers and shall b ws of New York State o i is Warranty sha e pany only in the court

The form of th t

THE TERMS OF THIS TO SAL T. THIS WARRAN E OF NO EFFECT IF AT THE TIME OF SALE A N POSTED ON THE COMPANY E THAT EVENT, THE TERMS OF THE POSTED WARRANTY SHALL APPLY EXCLUSIVELY.

Vicon Part Number: 8006-9010-03-05 Rev 508

parts warrant purchase.

u Such continuous operation is outside the arranty.

se of “autop na ” or “tour” modes of operation.

e remedy under

repair cente

in any of i s

merchan

to the Purcha

s located in the S

is Warran y is effective May 14, 2008.

TY SHALL B DIFFERE T WARRANTY IS

’S WEBSIT , WWW.VICON-CCTV.COM. IN

qui

defec

ts in material and workmanship

f three years, with

e ads warranted for 120 d hase. All other

ls: Labor and video he ays from date of original retail purc

d al retail purchase.

e for one year from date of origin

CRT (cathode ray tube) and L

r One year from date of original retail

Power Supplies: Two years from

le ase.

-308 and VDR-316 Recorder Se

e year from date of original retail p

ths from date of origina

udes prolonged use of lens and pan-and-tilt motors, gear to continuous

s the date original end-user take

e ment, or, at the sole discre

quipment first becomes operation

inal end-use .

this Warranty is that defective equipment be provided the equipment has be

with policy.

y are not defective, or any equ

an ay have be n tampered with, alter

ized repair.

er separately or in hardware

e error (bug) free. Software

l if provided at no cos

e without notice at Vicon’s sole products at an

ieu of all other conditions and

ility or fitness and th

tab cified in this Warran

ser.

ssume any liability on beone is authorized to

a pany, or impose

oods, o

l, or other damages, whethe

ti equipment operation,

nt or software, costs or repairs u

e , or other causes.

all sales made by the Company

to e governed by the la

ts conflict of laws principles. Th

ll be enforc able against the

tate of New York.

WARRANTY APPLY ONLY ES MADE WHILE THIS WARRANTY IS IN EFFEC

l retail purchase.

ing abus o

d on an “As Is”

ia telephone

express or implied s to the

the following exceptions: se from the da e of original ret

scope of this w

t the Company’s option) replac

he Company, and the return shirs

basis. Vicon does n

ny obligations on it in

ill the

ompany b

e liable for ther than that which is specified

ke cti rves the right to ma

Com without regard t

XX134-07-00 Rev 908 SurveyorVFT Camera Dome System 14BVicon Standard Equipment Warranty • 71

Vicon Industries Inc.

Co te Headquarterrpora s

89 Arkay Drive

Hauppauge, New York 11788

631-952-CCTV (2288) 800-645-9116

Fa -951-CCTV (2288x: 631 )

Vicon Europe Headquarters

Brunel Way

Fareham, PO15 5TX

United Kingdom

+44 (0) 1489 566300

Fax: +44 (0) 1489 566322

Germany

vin-videotronic infosystems gmbh

Lahnstrasse 1

D-24539 Neumuenster

Phone: +49 (0) 4321 8790

Fax: +49 (0) 4321 879 47

Far East Office

Unit 5, 17/F, Metropole Square

2 Yiu Street On , Shatin

New Territories,

Hong Kong

(852) 2145-7118

Fax: (852) 2145-7117

Intern .vicon-cctv.com et Address: www

Vicon SurveyorVFT SVFT-C22C, SurveyorVFT SVFT-W22C, SurveyorVFT SVFT-W22, SurveyorVFT SVFT-P22, SurveyorVFT SVFT-C23 Installation And Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual