Vibra-Tite 111 Technical Data

Technical Data Sheet
0%
20%
40%
60%
80%
100%
120%
5 min 10
min30min
2 hr 4 hr 8 hr 24 hr
Cure Time
% of Full Stre ngth
Steel Phosphate/oil Zi nc
Vibra-Tite® 111

Product Description

Vibra-Tite 111 i s a l ow s trength, an aerobic t hread locking c ompound. V ibra-Tite 111 i s de sign for locking t hreaded f asteners t hat r equire d isassembly with standard h and tools. The product performs on aluminum, steel, p lated, s tainless steel, an d special alloy p arts. V ibra-Tite 111 e xhibits g ood temperature and solvent resistant.

Typical Applications

Vibra-Tite 111 will lock and seal s mall screws (less than ¼ ”), s et s crews, a nd s crews t hat ha ve l ong engagement length.

Properties of Uncured Material

Chemical Type: Anaerobic Appearance: Purple Toxicity: Low Solids: 100% Viscosity @ 25ºC, cP Brookfield RVT,
Spindle 3 @ 20 rpm: 900-1500
Specific Gravity: 1.05

Typical Curing Performance

Cure Speed
The cure speed is depended on t emperature and substrate. T he g raph b elow s hows t he B reakaway Strength on M-10 Steel, Phosphate/oil, and Zinc finishes.
Threadlocker
December 2016

Performance of Cured Material

Typical Values
Fixture Time: 15-20 min@ 72 Full Cure Time: 24 hrs @ 72 Temperature Range: -60

Breakaway Strength

3/8” Plain Steel nut and bolt @1 hr 10-80 lb 3/8” Plain Steel nut and bolt @24 hr 50-100 lb 3/8” Zinc nut and bolt @ 24 hr 10-40 lb

Environmental and Fluid Resistance

(Shear strength values after 1,000 hours.) Typical Values Heat age @ 150 Engine oil @ 150 Brake fluid @ 150 ATF @ 150 50/50 water/ethylene glycol @ 120 Water @ 100 Gasoline @ 25 Diesel fuel @ 25 Ethyl Alcohol @25
o
C 100%
o
C 85%
o
C 85%
o
C 85%
o
C 80%
o
C 95%
o
C 100%
o
C 90%

Compatible Primers

Primers such as Vibra-Tite Excel 611 (Primer N) or Excel 612 (Primer T) can be used to speed the fixture time of the adhesive. Fixture times can improve by as much as 50%. The use of primers can result in lower strength a nd performance s hould b e tested af ter f ull cure.
o
F
o
F
o
F to 300oF (-51oC to 150oC)
-in
f
-in
f
-in
f
o
C 80%
Technical Data Sheet
Vibra-Tite® 111

General Information

Storage

Product should be stored in a cool and dry location at temperatures b etween 14°F ( -10°C) to 86°F ( 30°C). Shelf l ife i s 2 years from d ate o f manufacture when stored at 72±8°F (22±4°C).

Note

Vibra-Tite 111 is s uitable f or m ost small d iameter, fine t hreaded screws, nuts a nd bol ts. N ot recommended on certain p lastics as stress cr acking may occur. Vibra-Tite VC-3® Threadmate may be a possible a lternative s olution (compatibility must b e tested). S ome a nti-corrosion c hemicals i nhibit t he cure s ystem i n t his t ype o f an aerobic an d u se o f primer may b e re quired un der t hese c onditions. Product conforms to MIL-S-46163A, ASTM D-5363, NSF.

Health & Safety in use

IRRITANT: C ontains M ethacrylate E sters which may irritate eyes, respiratory organs and skin. In case of c ontact with t he s kin, wash immediately with plenty of water.
Threadlocker
December 2016
Loading...