Viavito FT500 Owner's Manual

Owner’s Manual.
FT500
Football Table
www.viavito.com
Manual version 1.0
Congratulations
Manual Contents.
on purchasing your very own FT500 Football Table.
You have chosen a high-quality, safe and innovative product, and we are certain it will keep you entertained for hours.
Please take the time to read this owner’s manual as it will help you to get the most out of your new product.
For more information, or if you require any assistance please email us at
support@viavito.com
Safety Information 03
Assembly 04/17
Contents Checklist 04/05 Assembly Instructions 06/17
Table Maintenance and Care 18
Customer Support 19/20
Contact Information 19 Manufacturer’s Warranty 20
Technical Information 21/22
Parts List 21 Exploded Diagram 22
02 www.viavito.com
Safety Information.
• Please read all the instructions carefully before using this product.
• Retain this manual for future reference.
• The specications of this product may
vary slightly from the illustrations and are subject to change without notice.
IMPORTANT SAFETY NOTICE: note the following precautions before using the product.
01 Assemble the product exactly as per
the instructions in this manual. We recommend that two adults work together to assemble this table.
02 Check all the screws, nuts and other
connections before using the table for
the rst time and ensure that it has
been built correctly and is safe to be used.
07 Do not place anything on the top of the
playeld.
08 Please keep in mind that player rods
are constantly moving in and out during play. To maintain personal safety and avoid injury, do not get too close to the table when pushing and pulling the rods to reposition your players.
03 Set up the table in a dry, level place and
keep it away from moisture and water.
04 This product is for home use only.
05 Warning! Not suitable for children
under three years.
06 Choking hazard! Keep small parts and
polybags away from children during and after assembly.
SAFETY STANDARDS This product meets the requirements of European safety standard EN 71-1/2/3.
03www.viavito.com
Assembly.
Contents Checklist
Before you begin the assembly, remove all of the contents from the box and make sure that you have all the parts listed and in correct quantities. This will ensure the quickest and most organized assembly.
#1
x1
Assembly Frame
#5
#2
x1
Support Brace
#6
An electric screwdriver can be used in the assembly. Set it to a very low torque and use with extreme caution to prevent damage to the product.
#3
x2
Leg Panel
#7
#4
Leg Type A
#8
x2
#9
#13
Leg Type B
Leg Leveler
Players
x2
x4
x22
#10
#14
Support Strut
Stop Ring
Rod Handle
x2
x4
x8
Metal Plate with Ring
#11
Rod Bumpers
#15
Rod End Cap
x2
x16
x8
x4
Metal Plate
#12
x16
Plastic Rod Washer
#16
x2
Ball Entry Cup
04
www.viavito.com
#17
#18
#19
#20
Soccer Ball (Black/ White)
#21
5-Man Rod
#25
1/4” *1-3/8” Bolt
#29
x2
x2
x14
#22
#30
Scorer
M4X28mm Bolt
1/4” Washer
x2
x26
x40
#23
#27
5/16” *1-3/8” Bolt
#31
3-Man Rod
M4 Nut
x4
x26
x12
x2
2-Man Rod
#24
x12
1/4” *1-3/4” Bolt
#28#26
x12
5/16” Washer
#32
x14
1/4” Nut
#33
x1
Allen Key
www.viavito.com
F3.5X45mm Screw
#34
Soccer Ball (White)
x4
x2
T3.5mmx12mm Screw
#35
Screwdriver
x6
x1
Allen Wrench
05
Assembly Instructions
Find a clean and level surface to begin the assembly of your football table. The table will be partially assembled upside down and then turned over onto its legs. Turning over the table will require at least two strong adults.
Your table comes mostly pre-assembled. Follow these easy steps to quickly and safely put the table together and get it ready to start playing. Estimated setup time is 30 minutes.
Parts
#2
x1
Support Brace
#7
x2
Metal Plate with Ring
Step One.
01 Attach (#7) Metal Plates with Ring to the (#2) Support Brace
using four (#25) Bolts with #26 Washers.
02 Fasten the support brace and metal plates using (#26) Washers
and (#29) Nuts.
#25
x4
1/4” *1-3/8” Bolt
#26
x8
1/4” Washer
#29
x4
1/4” Nut
Tools
#33
06
x1
Allen Key
#32
x1
Allen Wrench
www.viavito.com
Step Two.
01 Position the (#2) Support Brace with
xed metal rings in the center of the playeld and align with pre-drilled
holes in the cabinet’s side panels.
Parts
#1
x1
Assembly Frame
#2
Support Brace with Metal
Rings from Step 1
x1
02 Attach using (#24) Bolts with (#26)
Washers.
#24
1/4” *1-3/4” Bolt
#26
1/4” Washer
Tools
#33
Allen Key
x4
x4
x1
www.viavito.com
07
Step Three.
01 Secure (#4) Leg Type A and (#5) Leg
Type B to the table as shown on the drawing below using (#27) Bolts and (#28) Washers.
Parts
#4
x2
Leg Type A
#5
x2
Leg Type B
#27
5/16” *1-3/8” Bolt
#28
5/16” Washer
Tools
#33
Allen Key
x12
x12
x1
08
www.viavito.com
Step Four.
01 Attach (#8) Metal Plates to the (#3)
Leg Panel using four (#25) Bolts with
(#26) Washers. Fasten the leg panels and metal plates using (#26) Washers and (#29) Nuts.
Parts
#3
x2
Leg Panel
#8
x4
Metal plate
#25
02 Repeat above steps for the second leg
panel.
1/4” *1-3/8” Bolt
#26
1/4” Washer
#29
1/4” Nut
Tools
#33
Allen Key
x8
x16
x8
x1
#32
x1
Allen Wrench
www.viavito.com
09
Step Five.
01 Connect Left and Right legs using the
panels assembled in the previous step using (#24) Bolts and (#26) Washers.
Parts
#3
Leg Panel with metal plates
from Step 4
#24
1/4” *1-3/4” Bolt
#26
1/4” Washer
Tools
#33
x2
x8
x8
10
x1
Allen Key
www.viavito.com
Step Six.
01 Using (#25) Bolt with (#26) Washer
attach (#6) Support Strut to the metal plate of the leg panel. Tighten the bolts using another (#26) Washer and (#29) Nut on the other side of the panel.
02 Hook the other end of the (#6) Support
Parts
#6
x2
Support Strut
#25
x2
1/4” *1-3/8” Bolt
Strut into the metal ring of the support brace.
03 Repeat as above for the second support
strut.
04 Attach one (#9) Leg Leveller to the
bottom of each leg.
#26
#29
#9
#32
1/4” Washer
1/4” Nut
Leg Leveler
x4
x2
x4
#33
#33
Tools
Tools
x1
Allen Wrench
www.viavito.com
Allen Key
Allen Key
x1
x1
11
11
Step Seven.
01 Turn the football table over.
CAUTION!
1: It is recommended that two adults turn the table over. 2: Take hold of the table as shown. 3: Turn the table over. 4: Place the table on all four feet at the same time.
Take hold of the
table.
DO NOT hold the table by the legs.
DO NOT lean the table
on its legs.
12
www.viavito.com
#19
Parts
Step Eight.
Each side has four player rods to be set in a 1-2-5-3 formation. The correct layout starting at either end is:
3-Man Rod
#20
2-Man Rod
#21
5-Man Rod
#10
Stop Ring
#12
Plastic Rod Washer
#11
x4
x2
x2
x4
x16
1 home player
2 home players
3 away players
5 home players
5 away players
3 home players
2 away players
1 away player
Goalkeeper Setup
Start by setting up a goalkeeper at either end of the table.
01 Take (#19) 3-Man Rod and insert it into the corresponding hole
in the side panel. Thread the rod through just one hole and not all the way through the cabinet!
02 Slide onto the rod, one by one, (#11) Rod Bumper, (#12)
Plastic Rod Washer, rst (#10) Stop Ring, one (#13) Player
(ensure your goalie is facing the right direction!) and then second (#10) Stop Ring, second (#12) Plastic Rod Washer and second (#11) Rod Bumper.
03 Align Stop Rings and Player with pre-drilled holes in the rod and
screw them in place using (#22) Bolts and (#23) M4 Nuts. Now insert the rod through the hole on the opposite side of the table.
x16
Rod Bumper
#13
Player
#22
2x11
www.viavito.com
M4X28mm Bolt
x26
#23
M4 Nuts
x26
#35
#35
Tools
Screwdriver
13
Assembly of Team Players
Note: Ensure that all team players are facing the same direction as their goalkeeper!
01 Insert Rods number 20, 21 and 19 into the second, fourth and sixth holes
respectively.
02 Slide onto each rod, one by one, (#11) Rod Bumper, (#12) Plastic Rod Washer and
appropriate number of Black or Grey team players (item #13). Align players with pre­drilled holes in the rod and insert (#22) Bolts into the front of each player. Secure on the back using (#23) M4 Nuts.
03 Finish the assembly of each rod by sliding on second (#12) Plastic Rod Washer and
(#11) Rod Bumper. Once complete thread the rod through the hole on the opposite
side.
Repeat the above steps for remaining rods.
14
www.viavito.com
#11 Rod Bumper
#19 Rod
#12 Plastic Rod Washer
#10 Stop Ring
#19 Rod
#20 Rod
#21 Rod
#21 Rod
#20 Rod
#19 Rod
#10 Stop Ring
#12 Plastic Rod Washer
#19 Rod
#11 Rod Bumper
www.viavito.com
15
Step Nine.
01 Push (#14) Rod Handles onto the
player rods and add (#15) End Caps at the opposite end.
02 Insert (#16) Ball Entry Cup into the
center hole of each side of the table. Secure it by screwing (#31) Screws.
Parts
#14
Rod Handles
#15
End Cap
Parts
#16
x8
x8
T3.5mmx12mm Screw
x2
Ball Entry Cup
#31
x6
T3.5mmx12mm Screw
Tools
#35
Screwdriver
16
www.viavito.com
Step Ten.
01 Screw (#18) Slide Scorers into the
pre-drilled holes above each goal using (#30) Screws.
Parts
#18
x2
Slide Scorers
#30
x4
F3.5X45mm Screw
#35
Tools
Screwdriver
www.viavito.com
17
Maintenance and Care.
01 We recommend that you keep the
table covered when not in use. This will prevent dust from building up and will prolong the life of your football table. If it does get dusty, use a clean, dry cloth to remove any of the loose dirt from the table. Do not use any cleaning products.
02 This table is designed for indoor use
only. Damage can occur if the table is exposed to water, dampness, high humidity, extreme temperatures, etc.
03 Do not sit, climb or lean on the table or
the rods.
04 Periodically check all screws and bolts
to make sure that they are secure and in good working condition. If loose, tighten with a Phillips-head screwdriver.
05 Do not drag the table when moving it
as this will damage the legs. Do not lift the table by the rods. When moving the
table, lift the table o its legs and place
it down on all four feet at the same time.
18
www.viavito.com
Customer Support.
Contact Information
Should you require any assistance regarding this product please gather the following information and then contact us using the details below:
• Original purchase date
• Place of purchase
• Information about the place and conditions of use
• Precise description of the issue or defect.
IMPORTANT!! - Please retain your sales receipt. Viavito Customer Care may request proof of purchase to validate eligibility for warranty service. Warran­ty cover starts from the date shown on the proof of purchase.
Viavito Ltd
Unit 8, Sabichi House
5 Wadsworth Road
Perivale, Middlesex
UB6 7JD
Email: support@viavito.com
The best way to contac us is via the website: www.viavito.com
https://www.facebook.com/MyViavito
https://instagram.com/Viavito
https://twitter.com/MyViavito
www.viavito.com
19
Manufacturer's Warranty
Viavito ltd warrants this product to be free of defects of material and workmanship, under normal use and conditions, for a period of 6 months from the date of the original purchase.
Terms.
This warranty extends only to the original purchaser and is not transferable. The war­ranty does not cover:
01 Normal wear and tear
02 Any changes to upgrade this product
from its normal state or use other than as described in the user manual
03 Damage resulting from:
a) Transport
Viavito is not responsible or liable for direct, indirect, or consequential losses arising out of or in connection with the use of this product or damages with respect
to any loss of property, revenue, prots,
enjoyment or use, nor for any costs of removal or installation of this product.
This warranty covers products purchased as new inside the United Kingdom.
This warranty is in addition does not in
any way aect your statutory rights.
b) Abuse, misuse, failure to follow in-
structions or improper or abnormal use
c) Non-home use - including commercial,
professional, or rental purposes
d) Repairs not provided by Viavito ltd
e) Accidents, lightning, water, re, or any
other causes beyond the control of Viavito
f) Improper location including, but not
limited to, humid, dusty, or outdoor environments.
20
www.viavito.com
Technical Information.
Parts List.
PART # PART NAME QTY
01 Assembly Frame 1 02 Support Brace 1 03 Leg Panel 2 04 Leg Type A 2 05 Leg Type B 2 06 Support Strut 2 07 Metal Plate with Ring 2 08 Metal Plate 4 09 Leg Leveller 4 10 Stop Ring 4 11 Rod Bumpers 16 12 Plastic Rod Washer 16 13 Players 11+11 14 Rod Handle 8 15 Rod End Cap 8 16 Ball Entry Cup 2 17 Soccer Ball (Black/ White) 2 18 Scorer 2 19 3-Man Rod 4
20 2-Man Rod 2 21 5-Man Rod 2 22 M4X28mm Bolt 26 23 M4 Nut 26 24 1/4” * 1-3/4” Bolt 12
25 1/4” * 1-3/8” Bolt 14 26 1/4” Washer 40 27 5/16” * 1-3/8” Bolt 12 28 5/16” Washer 12 29 1/4” Nut 14 30 F3.5X45mm Screw 4
31 T3.5X12mm Screw 6 32 Allen Wrench 1 33 Allen Key 1 34 Soccer Ball (White) 2 35 Screwdriver 1
www.viavito.com
1721
Exploded Diagram
22
www.viavito.com
Loading...