VIA Technologies VIPRO VP7806 User Manual

Panel PC with

Revision

1.0

user manual

VIPRO VP7806

Fanless

6.5” TFT LCD and Touch Screen

100-04122010-1958

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written permission of VIA Technologies, Incorporated.

All trademarks are the property of their respective holders. PS/2 is a registered trademark of IBM Corporation.

Disclaimer

No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no warranties, implied or otherwise, in regard to this document and to the products described in this document. The information provided in this document is believed to be accurate and reliable as of the publication date of this document. However, VIA Technologies assumes no responsibility for the use or misuse of the information in this document and for any patent infringements that may arise from the use of this document. The information and product specifications within this document are subject to change at any time, without notice and without obligation to notify any person of such change.

Regulatory Compliance

FCC-A Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his personal expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.

Tested To Comply With FCC Standards FOR HOME OR OFFICE USE

Battery Recycling and Disposal

Only use the appropriate battery specified for this product. Do not re-use, recharge, or reheat an old battery. Do not attempt to force open the battery. Do not discard used batteries with regular trash. Discard used batteries according to local regulations.

Safety Precautions

Do’s

o Always read the safety instructions carefully. o Keep this User's Manual for future reference. o All cautions and warnings on the equipment should be

noted.

o Keep this equipment away from humidity. o Lay this equipment on a reliable flat surface before setting

it up.

o Make sure the voltage of the power source and adjust

properly 110/220V before connecting the equipment to the power inlet.

o Place the power cord in such a way that people cannot

step on it.

o Always unplug the power cord before inserting any add-on

card or module.

o If any of the following situations arises, get the equipment

checked by authorized service personnel:

o The power cord or plug is damaged. o Liquid has penetrated into the equipment. o The equipment has been exposed to moisture. o The equipment has not worked well or you cannot

get it work according to User's Manual.

o The equipment has dropped and damaged. o The equipment has obvious sign of breakage.

Don’ts

o Do not leave this equipment in an environment

unconditioned or in a storage temperature above 60°C (140°F). The equipment may be damaged.

o Never pour any liquid into the opening. Liquid can cause

damage or electrical shock.

o Do not place anything over the power cord. o Do not cover the ventilation holes. The openings on the

enclosure protect the equipment from overheating

III

Box Contents and Ordering Information

Model

Model Number

Number Description

ModelModel

Number Number

VIPRO VP7806-R1N13A1 Standar

Description

DescriptionDescription

Standardddd kit

kit

StandarStandar

kit kit



1 x VIPRO VP7806 unit



1 x Software driver and utility CD



2 x Wall-mount bracket



2 x Panel-mount bracket



1 x package of panel/wall mounting screw



1 x 0.5cc Thermally Conductive Dispensable Gel in tube syringe



1 x Power cable, 2-pole Phoenix plug to DC-Jack

Optional Accessories

External AC

External AC----to

External ACExternal AC Model Number

Model Number Description

Model NumberModel Number 99G63-020186 AC-to-DC adapter, DC 19V/90W with 2-pole Phoenix

99G33-02058C Power cable, 180 cm, USA type 99G33-02057C Power cable, 180 cm, Europe type 99G33-02092C Power cable, 180 cm, Japan Type

to----DC Adapter and

DC Adapter and Power Cable

toto

DC Adapter and DC Adapter and

Power Cable

Power CablePower Cable

Description

DescriptionDescription

power plug

ABLE OF

ONTENTS

1 Product Overview............................................................................................... 1

Key Features...........................................................................................................3

Specifications ......................................................................................................... 4

VIPRO VP7806 Dimensions ...........................................................................8

Front View.........................................................................................................8

Back View ..........................................................................................................8

Right and Left View....................................................................................... 9

Accessories............................................................................................................10

Power cable 2-pole Phoenix...................................................................10

Panel-mount Brackets ................................................................................10

Wall-mount Brackets ..................................................................................11

Panel/Wall-mounting Screws ................................................................11

Heatsink Grease ............................................................................................11

2 VIPRO VP7806 Hardware Functionality...................................................13

Introduction of I/O Layout ...........................................................................14

Front View Layout.......................................................................................14

Top View Layout ..........................................................................................14

Bottom View Layout...................................................................................15

Right and Left View Layout.....................................................................15

I/O Connector Functionality........................................................................16

Power Button.................................................................................................16

Power Input Connector............................................................................16

USB Ports: USB Port 1 ~ Port 4 ..............................................................16

COM Port Connectors ...............................................................................17

LED Indicators................................................................................................18

VGA Connector............................................................................................18

LVDS Connector: LVDS2..........................................................................19

LAN ports: Gigabit Ethernet Port 1 and 2........................................20

3 Hardware Installation and Upgrade .......................................................21

Basic Installation .................................................................................................22

Opening the Chassis ..................................................................................22

Installing the Memory ................................................................................25

Installing the SATA 2.5” hard disk.........................................................28

Installing the CompactFlash Card........................................................30

Installing Panel mounting kit ..................................................................31

Installing Wall mounting kit (optional) ..............................................34

Setting Up the Jumpers..................................................................................36

Jumper Settings.............................................................................................36

CLEAR_CMOS: Clear CMOS jumper ...................................................37

AT/ATX Power mode Select ...................................................................39

PVDD2_SEL: LCD power jumper.........................................................40

4 BIOS Setup............................................................................................................41

Entering the BIOS Setup Menu ..................................................................42

Control Keys .........................................................................................................42

Navigating the BIOS Menus ........................................................................43

Getting Help ........................................................................................................43

Main Menu ...........................................................................................................44

Standard CMOS Features.........................................................................44

Advanced BIOS Features .........................................................................44

Advanced Chipset Features....................................................................44

Integrated Peripherals................................................................................44

FreeDOS Configuration ............................................................................44

Power Management Setup.....................................................................44

PnP/PCI Configurations.............................................................................45

PC Health Status............................................................................................45

Frequency/Voltage Control....................................................................45

Load Optimized Defaults..........................................................................45

Set Supervisor Password ...........................................................................45

Set User Password .......................................................................................45

Save & Exit Setup ..........................................................................................45

Exit Without Saving.....................................................................................45

Standard CMOS Features..............................................................................46

Date ....................................................................................................................46

Time ....................................................................................................................46

Video..................................................................................................................46

Halt On..............................................................................................................46

IDE Channels.......................................................................................................47

Advanced BIOS Features...............................................................................48

Virus Warning................................................................................................48

CPU L1 & L2 Cache.....................................................................................48

CPU L2 Cache ECC Checking................................................................48

Quick Power On Self-Test.........................................................................49

First/Second/Third Boot Device............................................................49

Boot Other Device.......................................................................................49

Boot Up NumLock Status.........................................................................49

Typematic Rate Setting ..............................................................................49

Typematic Rate (Chars/Sec) ....................................................................49

Typematic Delay (Msec)............................................................................50

Security Option..............................................................................................50

MPS Version Control for OS....................................................................50

OS Select for DRAM > 64 MB .................................................................50

HDD S.M.A.R.T Capability .........................................................................50

Video BIOS Shadow ...................................................................................50

Full Screen Logo Show .............................................................................50

Summary Screen Show.............................................................................50

CPU Feature.........................................................................................................51

Thermal Management...............................................................................51

Thermal Monitor Bus Ratio......................................................................51

Thermal Monitor Bus VID ........................................................................51

Hard Disk Boot Priority....................................................................................52

Advanced Chipset Features .........................................................................53

Memory Hole .................................................................................................53

System BIOS Cacheable ............................................................................53

Video RAM Cacheable ..............................................................................53

GFX & PCIE VGA Co-Exist ........................................................................53

Internal VGA Control.......................................................................................54

VGA Share Memory Size ..........................................................................54

Direct Frame Buffer.....................................................................................54

Select Display Device..................................................................................54

Panel Type .......................................................................................................54

CPU & PCI Bus Control ...................................................................................55

PCI Master 0 WS Write ..............................................................................55

PCI Delay Transaction ................................................................................55

VIA PWR Management.............................................................................55

Integrated Peripherals.....................................................................................56

VIA OnChip IDE Device .................................................................................57

CF Card ATA66 .............................................................................................57

SATA Controller.............................................................................................57

IDE DMA Transfer Access ........................................................................57

OnChip IDE Channel 1 .............................................................................57

IDE Prefetch Mode ......................................................................................57

Secondary Master PIO ...............................................................................57

Secondary Slave PIO...................................................................................57

Secondary Master UDMA ........................................................................58

Secondary Slave UDMA............................................................................58

IDE HDD Block Mode ................................................................................58

VIA OnChip PCI Device..................................................................................59

Azalia HDA Controller................................................................................59

OnBoard LAN Boot ROM ........................................................................59

SuperIO Device...................................................................................................60

Onboard Parallel Port.................................................................................60

Parallel Port Mode........................................................................................60

Watch Dog Timer Select ..........................................................................60

SuperIO COM Ports (UARTs)........................................................................61

VII

Onboard Serial Port 1 ................................................................................61

COM1 RS232/422/485 Type .................................................................61

Onboard Serial Port 2 ................................................................................61

COM2 RS232/422/485 Type .................................................................61

Onboard Serial Port 3 ................................................................................61

Onboard Serial Port 4 ................................................................................61

USB Device Setting ...........................................................................................62

USB 1.0 Controller .......................................................................................62

USB 2.0 Controller .......................................................................................62

USB Operation Mode ................................................................................62

USB Keyboard Function............................................................................62

USB Mouse Function .................................................................................62

USB Storage Function................................................................................63

USB Wireless LAN Support......................................................................63

FreeDOS Configuration .................................................................................64

Boot into FreeDOS ......................................................................................64

Power Management Setup..........................................................................65

ACPI Suspend Type .....................................................................................65

Power Management Option..................................................................65

HDD Power Down .....................................................................................65

Suspend Mode ..............................................................................................65

Video Off Option..........................................................................................66

Video Off Method........................................................................................66

MODEM Use IRQ .........................................................................................66

Soft-Off by PWRBTN....................................................................................66

Run VGABIOS if S3 Resume....................................................................66

AC Loss Auto Restart ..................................................................................66

Wakeup Event Detect.....................................................................................67

PowerOn by PCI Card ...............................................................................67

RTC Alarm Resume ......................................................................................67

Date (of Month)............................................................................................67

Resume Time (hh:mm:ss) .........................................................................67

PnP/PCI Configurations..................................................................................68

Init Display First..............................................................................................68

PNP OS Installed ...........................................................................................68

Reset Configuration Data.........................................................................68

Resources Controlled By...........................................................................69

PCI/VGA Palette Snoop ............................................................................69

Assign IRQ for VGA.....................................................................................69

Assign IRQ for USB ......................................................................................69

Maximum Payload Size..............................................................................69

PC Health Status.................................................................................................70

Frequency/Voltage Control.........................................................................71

DRAM Frequency ........................................................................................71

VIII

DDR CAS Latency Control .......................................................................71

DDR Burst Length........................................................................................71

DDR 1T Command Rate ...........................................................................71

DRDY Table .....................................................................................................71

ODT.....................................................................................................................71

Spread Spectrum..........................................................................................72

Load Optimized Defaults...............................................................................73

Set Supervisor/User Password ....................................................................74

Save & Exit Setup ...............................................................................................75

Exit Without Saving ..........................................................................................76

5 Driver Installation...............................................................................................77

Driver Utilities.......................................................................................................78

Getting Started ..............................................................................................78

Running the Driver Utilities CD .............................................................78

CD Content ..........................................................................................................79

Product Overview

The VIPRO VP7806 Fanless Panel PC is an embedded panel computer with a 6.5” TFT LCD and Five-Wire Resistive Touch Screen. It has a default 2.0 megapixel camera, stereo speakers, and MIC-in that makes it good for multimedia applications. Its LCD offers wide viewing angles; high contrast and high brightness which can operate up to 700 nits (cd/m²) of brightness. The VIPRO VP7806 also comes with robust housing design that withstands shock and vibration. Its IP65 compliant front panel protects against water and dust.

The VIPRO VP7806 accepts a wide range of DC power input voltages (from DC 7V – 36V). It provides multiple external I/O connectors such as Gigabit Ethernet ports, USB 2.0 ports, configurable COM ports, LVDS port and VGA port. Storage can be integrated into its 2.5-inch internal HDD drive bay and external Compact Flash socket. It also includes a variety of mounting options that make it a flexible system to install.

The VIPRO VP7806 system is based on the Em-ITX mainboard form factor and powered by a VIA Nano 1.3 GHz processor — making it an ideal solution for applications that require low power consumption, and fanless, noise-free operation.

These features make the VIPRO VP7806 Fanless Panel PC suitable for a wide variety of embedded, multimedia, and industrial HMI (Human Machine Interface) applications including factory automation systems, precision machinery, production process control, terminal information systems, entertainment management systems, and car park automation systems…etc. The VIPRO VP7806 is a reliable, cost-effective solution that can shorten your application development time.

KEY FEATURES

Fanless and Ultra Low Power Consumption

Fanless and Ultra Low Power ConsumptionFanless and Ultra Low Power Consumption

 VIA Nano 1.3 GHz Ultra Low Power processor.  Noise free and fanless operation.

CCCCompact

ompact and R

ompactompact

Multiple I/O Integration and Networking Function

Multiple I/O Integration and Networking FunctionMultiple I/O Integration and Networking Function

Water and Dust Resistant

Water and Dust Resistant Front Panel

Water and Dust ResistantWater and Dust Resistant

Empowered Multimed

Empowered Multimedia Capabilities

Empowered MultimedEmpowered Multimed

Wide Range of Power Source

Wide Range of Power SourceWide Range of Power Source

Panel/Wall Mountabl

Panel/Wall Mountableeee

Panel/Wall MountablPanel/Wall Mountabl

and Robust Housing Design

obust Housing Design

and R and R

obust Housing Designobust Housing Design

 Aluminum sealed construction.  Special cushioned hard disk bay design that absorbs

vibration to ensure maximum reliability under harsh conditions.

 Supports four USB 2.0 ports, enabling access to USB

peripherals such as storage subsystems, security ID devices, card readers, bar code scanners, multifunction printers and scanners individually dedicated or shared among users via the network, making the best of USB device investments.

 The VP7806 has two Gigabit Ethernet, and four serial ports

(two RS-232 and two RS-232/422/485 serial ports) that enable communication and control at field level for measurement and operator control of diverse automations, such as Embedded Device Servers for storage, image printing, medical applications, as well as security and access control for POI/POS/Kiosk.

Front Panel

Front Panel Front Panel

 IP65 compliant front panel protects against water and dust.

ia Capabilities

ia Capabilitiesia Capabilities

 Built-in 3D/2D performance graphics engine with MPEG-2/4

WMV9 decoding accelerator.

 Wide range of DC 7V~36V power source offers flexibility of

power input for various automation environments.

 Multiple mounting options make it easy to install anywhere,

including Panel mount and Wall mount.

SPECIFICATIONS

CPU

Processor Core Logic System

System Memory

Graphic

LCD Display

CPU

CPUCPU

• VIA Nano 1.3 GHz Processor

• NanoBGA2 package: compact 21 mm x 21 mm

• 800 MHz Front Side Bus speed

• 1 MB L2 Cache memory

System Chipset

System ChipsetSystem Chipset

• VIA VX800 Unified Digital Media IGP chipset

BIOS

BIOSBIOS

• Award BIOS

• 8Mbit SPI Flash BIOS

• Supports Diskless Boot to BIOS ROM (Free DOS operating system environment)

System Power Management

System Power ManagementSystem Power Management

• Times Power On

• ACPI Supported

Technology

TechnologyTechnology

• One 200-pin SODIMM socket support DDR2 533/667 SDRAM

Maximum Capacity

Maximum CapacityMaximum Capacity

• Supports memory sizes up to 2 GB

Controller

ControllerController

• Integrated VIA Chrome9 HC3 DX9 3D/2D graphics engine with MPEG-2/4 WMV9 video decoding acceleration built-in VIA VX800 Unified Digital Media IGP chipset

Display Memory

Display MemoryDisplay Memory

• Optimized shared memory architecture, supports up to 256 MB frame buffer using system memory

External Display Interface

External Display InterfaceExternal Display Interface

• Supports one external VGA port by a DB-9 connector

• Supports one 24-bit single-channel LVDS interface by a DB-26 connectors

LCD Type

LCD TypeLCD Type

• 6.5” color TFT LCD panel, LED driving

Resolution/Color

Resolution/ColorResolution/Color

• Supports up to 640 x 480 @ 262K

Pixel Pitch

Pixel PitchPixel Pitch

• 0.207 mm x 0.207 mm

Viewing Angle

Viewing AngleViewing Angle

• 80˚ (right), 80˚ (left), 70˚ (up) and 70˚ (down)

Luminance

Luminance::::

LuminanceLuminance

• 700 cd/m²

LED Backlight MTBF

LED Backlight MTBFLED Backlight MTBF

• 50,000 hours (typical)

Touch Screen

Gigabit Ethernet

Audio

Serial

Storage

System Indicator

Camera

Watchdog Timer

Type

TypeType

• Fire-Wire Analog resistive

Transparency

TransparencyTransparency

• 80% ± 3%

Controller:

Controller: Controller:

• Built-in system a EETI ETP-CP-S5XU, USB interface controller

Software Driver:

Software Driver: Software Driver:

• Supports Windows XP and Windows 7

Durabuility (Knock Test)

Durabuility (Knock Test)::::

Durabuility (Knock Test)Durabuility (Knock Test)

• 35 million

Controller

ControllerController

• Two VIA VT6130 Gigabit Ethernet controllers

Interface

InterfaceInterface

• Support two RJ45 connectors

• Supports Wake On LAN (WOL)

• Supports Preboot Execution Environment (PXE)

Controller

ControllerController

• VIA VT1708B High Definition Audio Codec

External Speakers

External SpeakersExternal Speakers

• Supports left and right speakers on front bezel

External Microphone

External MicrophoneExternal Microphone

• Supports microphone on front bezel

Interface

InterfaceInterface

• Supports four USB 2.0 ports

•

USB 2.0 compliant

• Support 4 COM ports

• Two RS-232/422/485 configurable via BIOS setup

• Two RS-232

Serial ATA

Serial ATA HDD

Serial ATASerial ATA

• Supports a hard disk drive bay space for 2.5-inch of SATA

CompactFlash

CompactFlashCompactFlash

• One socket support type I/II CompactFlash disk

Power Status LED

Power Status LEDPower Status LED

• One green color LED

HDD Activity LED

HDD Activity LEDHDD Activity LED

• One red color LED

Built

Built----in a 2

BuiltBuilt

Output

OutputOutput

• System reset

Interval

IntervalInterval

• Programmable 1~255 sec.

HDD

HDD HDD

Hard Disk Drive.

in a 2.0

.0 mmmmega

in a 2in a 2

egapi

.0.0

egaega

pixel CMOS came

xel CMOS camera on the front bezel

pipi

xel CMOS camexel CMOS came

ra on the front bezel

ra on the front bezelra on the front bezel

System I/O ports

Power Supply

Mechanical Characteristics

Top

Top I/O Coastline on PC Unit

I/O Coastline on PC Unit

TopTop

I/O Coastline on PC UnitI/O Coastline on PC Unit

• One DB-9 connector for a VGA/CRT interface

• One DB-26 connectors for a 24-bit single channel LVDS

interface (LVDS2)

• Two RJ-45 connectors for dual Gigabit Ethernet

connection (LAN1 and LAN2)

• Two USB mini-DIN connectors (USB3 and USB4)

Bottom I/O Coastline on PC Unit

Bottom I/O Coastline on PC UnitBottom I/O Coastline on PC Unit

• One HDD and PWR LED

• Two RS-232/422/485 COM port connectors (COM 1 and COM2)

• Two RS-232 COM port connectors (COM3 and COM4)

• Two USB mini-DIN connectors (USB1 and USB2)

• One Phoenix 2-pole power input connector

• One ATX power On/Off switch button

Input Voltage

Input VoltageInput Voltage

• Built-in onboard DC-to-DC converter

• Accept wide range of Power Input of 7VDC ~ 36VDC

• Typical Power Input

• 7 VDC @ 2.64 A

• 12 VDC @ 1.54 A

• 16 VDC @ 1.15 A

• 19 VDC @ 0.97 A

• 24 VDC @ 0.77 A

• 36 VDC @ 0.51 A

• Support AT and ATX mode

Input

Input Power Protection

Power Protection

Input Input

Power ProtectionPower Protection

• Supports over voltage protection

• Supports over current protection

• Supports under voltage protection

Construction

ConstructionConstruction

• Aluminum mixed with heavy-duty steel

Mounting

MountingMounting

• Panel/wall mountable

Dim

Dimension (W x H x

ension (W x H x DDDD))))

DimDim

ension (W x H x ension (W x H x

• 203 mm x 165 mm x 78.42 mm (7.9” x 6.5” x 3”)

Net

Net Weight

Weight

Net Net

WeightWeight

• 3 kg (6.6 lbs)

Environment Specifications

Software Compatibility

Operating

Operating Temperature

OperatingOperating

• With CompactFlash disk only: -20°C up to 60 °C

• With 2.5-inch hard disk drive: 0°C up to 45 °C

Storage Temperature

Storage TemperatureStorage Temperature

• -20°C up to 70 °C

Relative

Relative HHHHumidity

RelativeRelative

• 0% ~ 90% @ 45% °C, non-condensing

Vibration loading during operation

Vibration loading during operationVibration loading during operation

• With CompactFlash disk only:

5Grms, IEC 60068-2-64, random, 5~500Hz, 1 Oct./min, 1hr/axis

• With 2.5-inch hard disk drive:

1Grms, IEC 60068-2-64, random 5 ~ 500Hz, 1 Oct./min, 1hr/axis

Shock during operation

Shock during operationShock during operation

• With CompactFlash disk only: 50G, IEC 60068-2-27, half

• With 2.5-inch hard disk drive: 20G, IEC 60068-2-27, half

Front Panel Protection

Front Panel ProtectionFront Panel Protection

• IP65 compliant

EMC A

EMC Approved

EMC AEMC A

• CE/FCC Class A

Safety Approved

Safety ApprovedSafety Approved

• UL, CCC

Operating System

Operating SystemOperating System

• Windows XP, Windows 7 and Windows XP Embedded

• Ubuntu Linux

Temperature

TemperatureTemperature

umidity

umidityumidity

sine, 11ms duration

pproved

pprovedpproved

VIPRO VP7806 DIMENSIONS

Front View

Back View

Right and Left View

ACCESSORIES

Power cable 2-pole Phoenix

Part # 99G33-250073

Panel-mount Brackets

Part # 99G42-091536-A1

Wall-mount Brackets

Part # 99G42-091376-A1

Panel/Wall-mounting Screws

Part # 99G44-010395

Heatsink Grease

Part # 99G26-110022

VIPRO VP7806

Hardware

This chapter provides information about the VIPRO VP7806’s external I/O connectors, switches, LED indicators and its functionality.

Section includes:

Introduction of I/O Layout I/O Connectors Functionality

Functionality

INTRODUCTION OF I/O LAYOUT

Front View Layout

Top View Layout

Bottom View Layout

Right and Left View Layout

I/O CONNECTOR FUNCTIONALITY

Power Button

The VIPRO VP7806 comes with a dual function Power On/Off button on the bottom I/O side that supports Soft Power -On/Off (i.e., Instant off or 4-Second Delay) and Suspend.

Power Input Connector

The VIPRO VP7806 comes with a Phoenix connector on the bottom I/O side that carries 7 ~ 36VDC external power input.

Pin Signal

1 GND 2 7VDC ~ 36VDC

USB Ports: USB Port 1 ~ Port 4

The VIPRO VP7806 provides four USB 2.0 interface connectors (USB1 ~ USB4). The USB1 and USB2 connectors are located on bottom I/O side while USB3 and USB4 are located on top I/O side. Each USB port supports Plug & Play and hot swapping for external devices. The USB interface complies with USB UHCI, Rev. 2.0.

The USB-interface connector is used for connecting any device that conforms to the USB interface. Many recent digital devices conform to this standard. The USB interface supports Plug and Play, which enables you to connect or disconnect a device whenever you want, without turning off the computer

Pin Signal

1 VCC 2 USB_P03 USB_P0+ 4 GND

COM Port Connectors

The VIPRO VP7806 provides four D-Sub 9-pin connectors: COM1, COM2, COM3 and COM4.

COM1 and COM2 ports

The VIPRO VP7806 provides two D-Sub 9-pin connectors (COM1 and COM2) for RS-232/422/485 serial communications on bottom I/O side.

RS-232 RS-422 RS-485 Pin Signal Signal Signal

1 DCD Tx- DATA2 RxD Tx+ DATA+ 3 TxD Rx+ NC 4 DTR Rx- NC 5 GND GND GND 6 DSR NC NC 7 RTS NC NC 8 CTS NC NC 9 RI NC NC

The default setting of COM1 and COM2 is RS-232, both COM1 and COM2 can be configured to operate in RS-232, RS-422 or RS485 mode by changing the settings in the BIOS setup menu. See page 65 for details.

Note:

Note:Note: NC represents “No Connection”

+ 62 hidden pages

VIA Technologies VIPRO VP7806 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual