VIA Technologies VESHPD01A1 User Manual

Quick Guide

SHP-D01

1. SHP-D01 Specifications

Item Description

Camera 500 megapixel wide-

angle color lens

2. SHP-D01 Front/Side panel

Front panel and size

3. SHP-D01 back panel

DC-In power

Door Station

Product Information

Product InformationProduct Information

Model:

Model: SHP-D01

Model: Model: Package Lists:

Package Lists:

Package Lists:Package Lists:

-SHP-D01 door station X 1

-RS485 cable X 1

-DIO cable X 1

-M4 * 30mm screw X 3

-8mm brass pipe + spring X 1

-Quick Guide X 1

Brightness exposure LED

Reader (RFID) Support 13.56MHz,

ISO14443A standard

Network Interface RJ-45

Network transmis-

10/100M

sion rate

Power DC-12V

Power consump-

<10W

tion

Operating tem-

0~40°

perature

Humidity 0~95%, non-condensing

Green LED Red LED

Green LED ON: normal operation

Green LED flash: booting

Red LED ON: ○1 Enable home or egress security

○2Anti-dismantle has been triggered

○3Security has been triggered

○4Force status has been triggered

Side panel and size

Adjustment of camera

RJ45 port

RS485 port

Red

black

brow

Purple

ring

DIO port

switch

DIO pin definition

black

Red

brow

DIO definition

DI1 reserved

DI2 reserved

DO1 Open the

door

DO2 reserved

DO3 reserved

Yellow

Orange

Green

reserved

Connect NO Relay default status is On

reserved

4. Relay connection (use

OMRON MY2-J Relay as an

Bleu

Purple

Grey

White

example)

Note

Note::::

NoteNote

1. This diagram is for reference only, please see DIO definition for actual connection.

2. Max. value of motion for DIO is 400mA.

3. DI can externally connect to spring switch

5. SHP-D01 Installation steps

1. Put brass pipe + spring on the embedded box, as indicated in the ○1.

2. Distance between bottom of the embedded box and the ground is 132 cm.

and NC of the dry contact. If the same DI needs to use 2 or more spring switches,

Alarm

speaker

connect by series.

4. DI that externally connects to switch (eg, doorbell, emergency pressure deduction) and gas detector, can connect to NO. To use 2 or more devices, connect by series.

○

5. If DI2 of the door station is not connected

Dry Contact

switch

to door detector, please short DI2 and DI2GND.

6. When DO connects to electric lock, power supply locks, interruption of power supply

132 cm

unlocks.

7. When DO connects to alarm, alarm connects to Relay NO, motion on Relay will

enable the alarm.

3. Remove two M2 screws from the bottom of the plaque. Take off the plate in order to separate the plaque and the main part.

plate

4. Use M4 screw to fix the main part.

5. Distance between bottom of the door station and the ground is 131 cm. Please consider the thickness of the tile or marble.

6. Put the front plaque and plate back. Fix the bottom with two M2 screws.

RFID area

Assistant Exposure

(within

rectangular area )

light

lens

key

Note

Note::::

NoteNote

M2 screw

6. SHP-D01 installation diagram

179.6 cm

145 cm

Height between lens and ground

110.4 cm

60 cm

Distance between lens and subject

Angle of view 60°

69.2 cm

M2 screw

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause.

CAUTION! To prevent shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified personnel.

M2 screw

1. Be careful of the orientation during

131 cm

installation.

2. Please do not install any other device

close to the door station, keep at least 10 cm

of distance.

VIA Technologies, Inc.

VIA Technologies, Inc.VIA Technologies, Inc.

1F, 531, Zhong-zheng Road,

For more information on this and

other VIA products, please visit :

www.viatech.com/en/

Xindian District, New Taipei City

231, Taiwan

Tel: 886-2-2218-5452

Fax: 886-2-2218-5453