Page 1
QuicQuic
QuicQuic
Quic
k User’k User’
k User’k User’
k User’
ss
ss
s
GuideGuide
GuideGuide
Guide
QuicQuic
QuicQuic
Quic
k User’k User’
k User’k User’
k User’
ss
ss
s
GuideGuide
GuideGuide
Guide
TRADEMARK
All products and company names are trademarks or registered
trademarks of their respective holders.
These specifications are subject to change without notice.
Manual Revision 1.0
September 29, 2005
6000002VKM310
VIA VIA
VIA VIA
VIA
P4M800P4M800
P4M800P4M800
P4M800
mainboard mainboard
mainboard mainboard
mainboard
for Intel Socket 775 processorfor Intel Socket 775 processor
for Intel Socket 775 processorfor Intel Socket 775 processor
for Intel Socket 775 processor
Page 2
2
English
DISCLAIMER OF WARRANTIES:
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE OF THE MANUFACTURER LIMITED
WARRANTY. THE MANUFACTURER EXPRESSLY EXCLUDES ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING ITS
PRODUCTS; INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR
NONINFRINGEMENT. THIS DISCLAIMER OF WARRANTIES SHALL
APPLY TO THE EXTENT ALLOWED UNDER LOCAL LAWS IN THE
COUNTRY PURCHASED IN WHICH LOCAL LAWS DO NOT ALLOW
OR LIMIT THE EXCLUSION OF THE IMPLIED WARRANTIES.
Page 3
3
English
Processor Support
Socket LGA775 for Intel
®
Celeron D® 3xx series, Intel® Pentium 4® 5xx/6xx
series up to 3.4GHz
Support Intel Pentium
®
with Dual core processor up to 2.8GHz
Support 533/800 MHz front-side bus
Chipset
VIA P4M800ce + 8237R Plus AGPset with VIA Unichrome Pro Graphics core
Main Memory
Two 184-pin DDR SDRAM DIMM sockets
Support single-sided or double-sided 2.5v DDR-266/333/400 DIMMs in 64/128/256/
512Mb/1Gb technologies
Support up to 2GB memory size
Expansion Slots
Three PCI connectors compliant with PCI v2.2
One 1.5v AGP-8X connector compliant with AGP v3.0
One CNR (Communication & Networking Riser) slot for V.92 analog Modem in
Secondary mode
I DE
Two IDE interfaces (up to 4 IDE devices) with UDMA-33, ATA-66/100/133
support from chipset IDE controller
USB
Eight USB connectors compliant with USB2.0 from embedded USB controller (4
connectors at rear panel)
S-ATA
Two S-ATA ports with up to 150MB/s bandwidth with RAID 0, 1, JBOD support
LAN
Integrates 10/100Mps Fast Ethernet controller with onboard VIA 6103L PHY LAN
I/O
Fintek LPC IO controller with PS/2 keyboard&mouse, floppy, printer, serial and
CIR/SIR interface
Support Hardware Monitoring function
Intelligent fan speed control for CPU-fan (PWM) for quiet operation
1. Specification
Page 4
4
English
Audio
Onboard Realtek ALC-655 selectable 2 or 6-CH audio CODEC
- AC’97 v2.3 compliant
- Supports CD-In, Aux-In
- Supports automatic “jack-sensing”
- Rear panel audio jacks configuration:
roloCkcaJoiduA
lennahc2 lennahc6
eulBthgiLni-eniLtuo-oeretsraeR
emiLtuo-eniLtuo-oeretstnorF
kniPni-ciMrefoowbuS&retneC
BIOS
Flash EEPROM with Award Plug & Play BIOS
Support ACPI S3 (Suspend To RAM) mode in ACPI compliant O/S
Support EZ Boot for fast bootable device selection
Support Magic Health for system hardware status report during system boot-up
Special Features
Support KBPO function – Keyboard power on, turn on the computer from keyboard
Support Wake-On-LAN by PME
Support USB resume in S3
PowerBIOS for excellent overclocking features:
- Programmable FSB Clock output frequency with 1MHz fine tuning
- Support BIOS adjustable CPU multiplier, FSB clock settings
Form Factor
245mm x 230 mm Micro-ATX size
Supported O/S
Windows 98SE/ Windows 2000/Windows XP
Page 5
5
English
1.2 Block Diagram
Page 6
6
English
2. Setting up the mainboard
Before assembling the mainboard into the PC case we recommend you to do the following:
1. CPU Installation
2. DDR Memory Insertion
After the mainboard is fitted into the case, you may
3. Install Add-on VGA or PCI cards (Optional)
4. Connect the internal cables and wires
5. Connect your external peripherals to the rear I/O port
3.1 CPU Installation
3. Installation
Step 1
Open load plate ( A ) , DO NOT touch
socket contacts ( B ).
Step 2
Remove protective cover ( C ) from load
plate. Please do not discard the protective
cover. Always replace the protective cover
if the processor is removed from the socket.
1
2
Page 7
7
English
Step 3
Remove the processor from the protective
cover. Do not touch the bottom of the
processor. The processor cover should not
be discarded. Always replace the processor
cover if the processor is removed from the
socket.
Step 4
Hold the processor with thumb and index
fingers as shown. Ensure fingers align to the
socket cutouts ( D ) , processor notches ( E )
align to socket convexes ( F ). Place the
processor straight down without tilting or
sliding in the socket.
Step 5
Place the fan heatsink onto the mainboard
with the fasteners align to the holes. Be care
not to damage the thermal interface material
attached to the bottom of the heatsink.
Rotate the clips 90 degrees to lock the CPU
cooler in place.
Connect the fan cable to the mainboard
header JCPU_FAN.
3 4
5
The CPU is keyed to prevent incorrect insertion, do not
force the CPU into the socket. If it does not go in easily,
check for mis-orientation.
Fan Clips
Page 8
8
English
3.3 VGA and PCI card installation
This mainboard is equipped with on-chip graphics engine, you may connect a VGA monitor
directly to its rear port. However, if you need to install VGA card follow the steps below.
To install a VGA card into the AGP slot or a PCI expansion card:
1. Remove the bracket (on the PC case) for the slot you intend to use.
2. Firmly press down the card into the slot until it is completely seated. For an AGP
card ensure the AGP slot clicker is locked as shown in the picture below.
3. Secure the card's bracket to the PC case with a screw.
3.2 DDR Memory Insertion
The mainboard accommodates two PC2100/PC2700/PC3200 184-pin DIMMs (Dual In-line
Memory Modules):
• Supports up to 2.0GB of 266/333/400MHz DDR SDRAM.
• Supports unbuffered non-ECC DIMMs.
• DDR SDRAM supports 64, 128, 256, 512MB and 1GB DIMM modules.
• Supports DRAM configurations defined in the JEDEC DDR DIMM specification.
The AGP slot supports only newer VGA cards with 1.5V specifications.
To install, align the notch on the
DIMM module with the connector.
Press straight down as shown in the
figure until the white clips close and
the module fits tightly into the
DIMM socket.
Notch
Page 9
9
English
3.5 Internal Connectors
3.4 Rear IO Port
7
2
1
8
3
9
10
COM
Parallel Port
RJ-45
LAN
USB2.0 ports
PS/2
Mouse
PS/2
Keyboard
Mic-in/Center&Subwoofer (Pink)
Line-out/Front out (Lime)
Line-in/Rear out (Light blue)
VGA
1
4
4
5
6
11
Page 10
10
English
Connectors Figure Discriptions
1
Ground
+12V
Sense
JCPU_FAN
JPWR_FAN
CPU / Power Fan Power Connectors
JCPU_FAN: Connect the CPU fan to this
connector.
JPWR_FAN: Use this connector if you are
installing an additional fan in the unit.
2
FDD
Floppy Drive Connector
3
IDE1
Primary IDE
IDE2
Secondary IDE
1
1
Primary/Secondary IDE Connector
Connects to the IDE device, i.e. HDD and CD-
ROM device.
4
PW1
PW12
1
3
1
-12V3.3V
Ground+5V
PS-ON+5V
-5VPW-OK
+5V5VSB
+5V+12V
+12V+12V
10
11
4
2
3.3V3.3V
GroundGround
GroundGround
GroundGround
GroundGround
20
PW1: 20-pin ATX Power Connector
PW12: 4-pin ATX12V Power Connector
The plugs of the power cables are designed to fit
in only one orientation.
5
CFPA
1
Rear Line-out-FR
Front Line-out-R
Rear Line-out-FL
Front Line-out-L
MIC_In
NC
+5V
Key
9
2
10
GND
CFPA: Front Panel Audio Connector
This connector is used only if the speaker and
microphone needs to be plugged at the front of
the PC case. Otherwise, leave the jumpers at the
default position.
1
When using two IDE drives on the same
connector, one must be set to Master
mode and the other to Slave mode.
Refer to your disk drive user’s manual
for details.
6
CD-IN/AUX-IN: CD Audio-in connectors
These connectors are used to receive audio from a
CD-ROM drive, TV tuner or MPEG card.
CD_IN_Left
1
CD_IN_Right
CD_Reference
AUX_IN_Left
1
AUX_IN_Right
GND
CD-IN
AUX-IN
The PW1 and PW12 Power Connector
must be used simultaneously.
Ground
+12V
Sense
Control
Page 11
11
English
Connectors Figure Discriptions
8
CFP
CFP: Case Front Panel Connector
HD_LED
This LED indicates hard drive activity.
PWR_LED
Connects to the power indicator on the PC case.
RST
Connects to the RESET switch on the PC case.
PW_ON
Connects to the Power button on the PC case, to
turn on the system. To turn off the system,
press the power button for 4 seconds.
CIR
CSPK
CIR: IR connector
For connection to an IrDA receiver unit.
CSPK: Speaker
Connects to the case’s speaker for PC beeps.
Settings:
1-2: Normal (Default)
2-3: Clear CMOS
JCMOS: Clear CMOS data Jumper
This resets the BIOS CMOS data back to the
factory default values. Recommend to leave at
Normal (default) postion.
JCMOS
10
7
CUSB3
CUSB4
CUSB3/CUSB4: Four USB2.0 header
This mainboard includes 4 additional onboard
USB ports.
To use these additional USB ports, a USB bracket
is required. Please contact your retailer for details.
1
GND
A-B-
B+
GND
A+
GND
SATA1
SATA2
SATA1 / SATA2: Two Serial ATA Connectors
These connectors enable you to connect Serial
ATA HDDs or optical drives type.
1
9
Settings:
1-2: Connect (S3 enabled)
2-3: Disconnect (No S3)
JUSB: USB S3 Wake up Jumper
This jumper disconnects 5V standby voltage to
USB devices. This means USB devices will not
be able to wake-up the system from S3 (Suspend
to RAM) power saving mode.
JUSB
11
1
Page 12
12
English
BIOS Setup
When you start up the computer for the first time you need to enter the BIOS CMOS Setup
Utility. Power on the computer and press <Del> key during POST (Power On Self Test).
The BIOS CMOS SETUP UTILITY opens as shown below:
< CMOS Setup Utility>
Select and enter "Load Optimized Defaults" page. This page loads the factory settings for
optimal system performance. Follow the simple on-screen instructions to complete this
procedure. Press "ESC" to exit and select "Save & Exit Setup" to continue to boot.
For more information regarding BIOS settings refer to the complete
manual in the bundled CD.
4. BIOS
Page 13
13
English
Insert the bundled CD into the CD-ROM and the main menu screen will appear. The main
menu displays links to the supported drivers, utilities and software.
Method 1
This item installs all drivers automatically.
Method 2
This item allows you to install the drivers selectively.
Step 1 : Click “VIA SERIES 4_IN_1 Driver” to install chipset driver.
Step 2 : Click “AC’97 AUDIO Driver” to install audio driver.
Step 3 : Click “VIA LAN Driver” to install LAN driver.
Step 4 : Click “VGA Driver” to install onboard graphics driver.
Step 5 : Click “USB V2.0 Driver” to install USB 2.0 driver.
Step 6 : Click “VIA SATA RAID Driver” to install Serial ATA driver.
5. Driver Installation
Once the operating system has been installed, you need to install the drivers for the mainboard.
Method 1
Method 2
Auto Installation
Manual Installation
>>VIA SERVICE PACK 4_IN_1 Driver
>>AC’97 AUDIO Driver
>>VIA LAN Driver
>>VGA Driver
>>USB 2.0 Driver
>>VIA SATA RAID Driver
Please select
Page 14
14
English
Download the xxxxx.EXE file corresponding to your model from our website to an empty
directory on your hard disk or floppy. Run the downloaded xxxxx.EXE file and it will self
extract. Copy these extracted files to a bootable floppy disk.
Note: The floppy disk should contain NO device drivers or other programs.
6. Flashing the BIOS
7. The BIOS update is finished.
XXXXX
XXXX
xxxxx.bin
F1 : Reset
F10 : Exit
8. Keep this BIOS floppy disk for future use.
5. Key in File Name to save previous BIOS
to file.
6. To confirm and proceed, please key in
[Y] to start the programming.
xxxxx.bin
xxxxx.bin
XXXXX
XXXX
XXXXX
XXXX
xxxxx.bin
xxxxx.bin
1. Type “A:\AWDFLASH and press <Enter> Key.
2. You will see the following setup screen.
3. Please key in the xxxxx.bin BIOS file
name.
4. If you want to save the previous BIOS
data to the diskette, please key in [Y],
otherwise please key in [N].
XXXX
xxxxx.bin
XXXX
XXXXX
Do NOT flash the system BIOS unless it is really necessary.
Updating and flashing the BIOS content risks BIOS data corruption which may
cause system unable to power-on.
Loading...