Page 1
WARNING
Use and Care Instructions
for Vision System with
DO NOT USE UNTIL ALL INSTRUCTIONS
REGARDING SAFETY HAVE BEEN READ.
Extended coverage
Page 2
Your new SENTRY by VFORCE combines solid durability
® TM
protection and comfort in a unibody constructed mask with
the thickest shell in it’s class. This mask protects from both
50cal and 68cal paintballs.
The renowned and reliable ARMOR lens design ensures
TM
distortion-free vision, enhancing your rapid target-acquisition
efficiency and overall safety.
The unique Quick-Change system allows you to remove
TM
the lens, eye foam, and strap in seconds for cleaning or
interchanging so you are quickly back in the game.
An integrated visor protects from sunny conditions and
doubles as a protective lens guard should your mask be
off and accidently thrown about.
Includes a built-in chin strap that keeps your mask super
secure throughout play.
A Free-Flow ventilated design ensures maximum
breathability in every playing condition.
Have fun, look great and always Play Safe!
Page 3
WARNING
Read and follow carefully all instructions and warnings contained in
this manual. Failure to observe all instructions and warnings could lead to
Remember that your mask cannot offer protection in all situations
severe or permanent injuries.
WARNING
This Vision System provides Extended Coverage as defined in
ASTM standard F1979. This Vision System is designed to fit users
of Adult Sizes Small, Medium and Large
Page 4
TABLE OF CONTENTS
Fitting 4
Mask and Lens Care
Lens Removal
Lens & Eye Foam Removal 7
Eye Foam Installation 8
Lens Installation 9
Chip Strap Installation 10
5
6
WARNING
Wear your paintball protective Vision System at all times
when playing, practicing or target shooting.
WARNING
Before each game, breathe on the inside surface of the lens.
If it fogs up: before using your mask - replace the lens or treat it with
VForce Anti-Fog Solution.
Page 5
Sentry
CLEANING
ANTI-FOG TREATMENT
STORAGE
Sentry
Page 6
SENTRY
Once clip slides
off repeat step on
other side of mask.
Push inner temple
clip firmly upwards
with your thumb
while holding top
of mask securely
with both hands.
Remove fastening clips
from both sides of lens
by pushing each clip from
the inside of mask with your
fingers releasing and sliding
the clip from under the lens
with your free hand.
WARNING
Check lens before each and every use. Replace the lens after one year
of use even if it seems to be perfect. Replace lens immediately if it
shows cracks or if it has received a direct impact from a ball shot
a distance of less than 10 feet (3m)
Page 7
LENS REMOVAL
SENTRY
Repeat step
5
on opposite
side and
remove lens
from mask.
EYE FOAM REMOVAL
Press on the
4
fastening tab
(edge of lens
temple area)
to dislodge
the lens from
mask.
Once all clips, fasteners
and lens are removed
the Eye Foam can
simply be popped
out by pulling it from
it’s support slots.
WARNING
Use only lenses specifically designed for this vision system model.
7
Page 8
EYE FOAM INSTALLATION
SENTRY
Angle EyeFoam
2
from support slot
on one side then
snap into opposite
support slot.
When secured you
will hear audable
“click” sound.
Insert EyeFoam
1
by resting one side
first on support slot.
“click”
8
Page 9
LENS INSTALLATION
SENTRY
1
Insert new lens
making sure that
both fastening tabs
are fully inserted
and securely in place.
Ensure that both
upper positioning tabs
are inserted in their
respective slots.
2
Reinsert fastening
clips by sliding and
snapping them under
the lens temple tabs.
WARNING
Ensure that the lens is firmly in place before wearing the mask.
Use only accessories that have been approved for your Sentry mask
Do not make and modifications to your mask.
by VForce. (The retention strap is not an ear protector.)
9
Page 10
CHIN STRAP INSTALLATION
SENTRY
Unfastening the buckle is
2
accomplished by squeezing
the right and left edges of the
“male” prongs until they are
automatically ejected from the
“female” portion.
1
To properly fasten the buckle
insert the “male” prongs into
the “female” portion until you
hear an audible “click”.
Adjust strap to fit snugly under
your chin.
WARNING
NEVER play a game of paintball
without the chip strap securely attached to the mask.
10
Page 11
This model is certified by: SAI Global Assurance Services Ltd.
Partis House, Ground Floor, Davy Avenue, Knowlhill, Milton Keynes
MK5 8HJ, United Kingdom - Notified Body Number: 2056
VFORCE VISION SYSTEMS
6000 Kieran, St-Laurent, Quebec, Canada
www.vforce.com
MADE IN CHINA
VFORCE and SENTRY are Registered Trademarks
TM
®
Loading...