Vezco VZ-IP-TCAMIDS-WI Quick Start Manual
Video Intercom Indoor
Station
Quick Start Guide
Video Intercom Indoor Station·Quick Start Guide
i
Quick Start Guide
The quick start guide is intended for the users of the indoor station.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, VEZCO MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.
Video Intercom Indoor Station·Quick Start Guide
ii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable harmonized
European standards listed under the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot
be disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated
collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point.
For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Video Intercom Indoor Station·Quick Start Guide
iii
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the
power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service
center. Never attempt to disassemble the device yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for the
detailed operating temperature), cold, dusty or damp locations, and do not expose it to
high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Video Intercom Indoor Station·Quick Start Guide
iv
Exposing the equipment to direct sun light, low ventilation or heat source such as heater
or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfunction however), and affecting the endurance of sensor
at the same time.
Please use the provided glove when open up the device cover, avoid direct contact with
the device cover, because the acidic sweat of the fingers may erode the surface coating
of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and
lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion. Replace
with the same or equivalent type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.
Video Intercom Indoor Station·Quick Start Guide
v
Table of Contents
1 Appearance ................................................................................................ 1
1.1 Appearance ............................................................................................................ 1
1.2 Terminals and Interfaces ........................................................................................ 3
2 Installation and Wiring ............................................................................... 4
2.1 Indoor Station Installation ....................................................................................... 4
2.1.1 Installation Plate ............................................................................................... 4
2.1.2 Wall Mounting with Gang Box of Indoor Station ............................................... 5
2.2 Indoor Station Wiring .............................................................................................. 8
2.2.2 Wiring ............................................................................................................. 8
3 Before You Start ......................................................................................... 9
4 Local Operation ........................................................................................ 10
4.1 Activating Device Locally ....................................................................................... 10
4.2 User Interface Description ..................................................................................... 11
4.2.1 User Interface of Indoor Station ...................................................................... 11
4.2.2 User Interface of Indoor Extension .................................................................. 12
4.2.3 Indoor Station Status ...................................................................................... 13
4.2.4 Indoor Extension Status .................................................................................. 14
4.3 Configuration Settings ........................................................................................... 15
4.3.1 Changing Configuration Password ................................................................... 15
4.3.2 Setting Local Information ................................................................................ 15
4.3.3 Setting Network .............................................................................................. 16
4.3.4 Adding Devices ................................................................................................ 17
4.4 Calling Resident ..................................................................................................... 20
5 Remote Operation (Batch Configuration Tool) ........................................... 21
5.1 Activating Device Remotely ................................................................................... 21
5.2 Editing Network Parameters .................................................................................. 22
5.3 Adding Device ........................................................................................................ 23
5.3.1 Adding Online Device ...................................................................................... 23
5.3.2 Adding by IP Address ....................................................................................... 24
Appendix .................................................................................................... 26
Installation Notice ....................................................................................................... 26
Wiring Cables .............................................................................................................. 26
Video Intercom Indoor Station·Quick Start Guide
1
1 Appearance
1.1 Appearance
Figure 1-1 Front Panel
Figure 1-2 Rear Panel
Video Intercom Indoor Station·Quick Start Guide
2
Table 1-1 Descriptions
No.
Description
1
Built-in Camera
2
Power Supply Indicator
3
Information Indicator
4
Alarm Indicator
5
Microphone
6
Management Center Touch Key
7
Live View Touch Key
8
Remote Unlock Touch Key
9
SOS Touch Key
Hold down the SOS touch key to trigger a SOS alarm and upload the alarm message to
the management center (VEZPRO client software or the master station).
Video Intercom Indoor Station·Quick Start Guide
3
1.2 Terminals and Interfaces
1 2 3 4 5
6
Figure 1-3 Rear Panel of
Type III and Type IV 8-Series
Models
Table 1-1 Descriptions of Terminals and
Interfaces
Name
No.
Interface
Description
TF Card Slot
1
TF Card Slot
Mechanical
Switch
2 Mechanical Switch of Built-in Camera
Power Supply
3
+12V
DC 12V Power Supply + Input
GND
DC 12V GND – Input
Network
Interface
4
LAN
Network Interface (Support Private POE)
Loudspeaker
5
Loudspeaker
Serial Port
6
Serial Port
485
Communication
Port
A1
RS485B+
Reserved
A2
RS485B-
A3
RS485A+
A4
RS485A-
Grounding
A5
GND
Grounding
Video Intercom Indoor Station·Quick Start Guide
4
Name
No.
Interface
Description
A6
GND
Grounding
ALARM OUT
(Alarm Output)
A7
COM1
Alarm Relay Output Terminal 1 (Dry Contact)
A8
NO1
A9
COM2
Alarm Relay Output Terminal 2 (Dry Contact)
A10
NO2
ALARM IN
(Zone Input)
B1
JIN8
Zone Detector Input Terminal 8
B2
JIN7
Zone Detector Input Terminal 7
B3
JIN6
Zone Detector Input Terminal 6
B4
JIN5
Zone Detector Input Terminal 5
B5
GND
Grounding
B6
GND
Grounding
B7
JIN4
Zone Detector Input Terminal 4
B8
JIN3
Zone Detector Input Terminal 3
B9
JIN2
Zone Detector Input Terminal 2
B10
JIN1
Zone Detector Input Terminal 1
2 Installation and Wiring
2.1 Indoor Station Installation
To install the indoor station onto the wall, an installation plate and a gang box are
required. The gang box of 8-series and 6-series indoor stations is the same.
2.1.1 Installation Plate
Please refer to the following figures for the dimensions of the installation plate of type II
6-series models and 8-series model.
Loading...