Vezco VZ-IP-2MLPRB Installation Manual

NETWORK CAMERA

Installation Manual

Installation Manual of Network Camera

Thank you for purchasing our product. If there are any questions, or requests, please do
not hesitate to contact us.

This manual may contain several technical incorrect places or printing errors, and the
content is subject to change without notice. The updates will be added to the new version of
this manual. We will readily improve or update the products or procedures described in the
manual.

DISCLAIMER STATEMENT

“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the

security or signaling aspects of this product. UL has only tested for fire, shock or casualty
hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification does not
cover the performance or reliability of the security or signaling aspects of this product. UL
MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”

2

Installation Manual of Network Camera

Warnings Follow these safeguards to

prevent serious injury or death.

Cautions Follow these precautions to

prevent potential injury or material
damage.

Safety Instruction

These instructions are intended to ensure that the user can use the product correctly to
avoid danger or property loss.

The precaution measure is divided into ‘Warnings’ and ‘Cautions’:

Warnings: Serious injury or death may be caused if any of these warnings are neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are

neglected.

Warnings:

 Please adopt the power adapter which can meet the safety extra low voltage (SELV)

standard. And source with 12 VDC or 24 VAC (depending on models) according to the
IEC60950-1 and Limited Power Source standard.

 If the product does not work properly, please contact your dealer or the nearest service

center. Never attempt to disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)

 To reduce the risk of fire or electrical shock, do not expose this product to rain or

moisture.

 This installation should be made by a qualified service person and should conform to all

the local codes.

 Please install blackouts equipment into the power supply circuit for convenient supply

interruption.

 Please make sure that the ceiling can support more than 50(N) Newton gravities if the

camera is fixed to the ceiling.

 If the product does not work properly, please contact your dealer or the nearest service

center. Never attempt to disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)

3

Installation Manual of Network Camera

Cautions:

 Make sure the power supply voltage is correct before using the camera.
 Do not drop the camera or subject it to physical shock.
 Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth

with a bit of ethanol and wipe it gently. If the camera will not be used for an extended
period of time, put on the lens cap to protect the sensor from dirt.

 Do not aim the camera lens at the strong light such as sun or incandescent lamp. The

strong light can cause fatal damage to the camera.

 The sensor may be burned out by a laser beam, so when any laser equipment is being

used, make sure that the surface of the sensor not be exposed to the laser beam.

 Do not place the camera in extremely hot, cold temperatures (the operating

temperature should be between -30°C ~ 60°C, or -40°C ~ 60°C if the camera model has

an “H” in its suffix), dusty or damp environment, and do not expose it to high

electromagnetic radiation.

 To avoid heat accumulation, good ventilation is required for a proper operating

environment.

 Keep out of water and any liquid.
 While shipping, the camera should be packed in its original packing.

 Improper use or replacement of the battery may result in hazard of explosion. Please

use the manufacturer recommended battery type.

4

Installation Manual of Network Camera

Table of Contents

Chapter 1 Introduction .........................................................................................................................6

1.1 Applications ..................................................................................................................................6

1.2 Preparations .................................................................................................................................6

Chapter 2 Bullet Camera Installation .................................................................................................. 8

2.1 Type X Bullet Camera ............................................................................................................... 147

2.1.1 Camera Description .................................................................................................... 147

2.1.2 Installation ................................................................................................................... 149

5