Vetra MegaSwitch VIP-802-KMAV2, MegaSwitch VIP-802-KM, MegaSwitch VIP-802 Series, MegaSwitch VIP-802-KMV, MegaSwitch VIP-802-KMV2 User Instructions

User Instructions for

VIP- 802 Series "MegaSwitch"

Keyboard, Mouse, Audio and Video Switch

FEDERAL COMMUNICATIONS COMMISSION

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at their expense.

CE

This equipment has been tested and found to conform to the directives and standards for a Class A Information Technology
Equipment type and for the Commercial Light Industrial equipment class.

INTRODUCTION

The VIP-802 "MegaSwitch" Keyboard, Mouse, Audio and Video Switches are available as a full function, Integrated Switch
with keyboard control selection, switching keyboard, mouse, audio, and video. The "MegaSwitch" allows one Workstation
comprised of a PC Keyboard, a PS/2 Mouse, Audio, and VGA Monitor to control and work with one or two PC's.

Note: The "MegaSwitch does not come with PS/2, Audio, or VGA extension cables.

Vetra separately.

INSTALLATION

There are two main steps to connect the Switch:

1. Connect PC's to Switch unit:

a) Keyboard

PC#1's keyboard port to the backpanel connector of the Switch marked "PC1 KBD". Connect PC#2's keyboard port to the
backpanel connector of the Switch marked "PC2 KBD".

b) Mouse

mouse port to the backpanel connector of the Switch marked "PC1 MSE". Connect PC#2's mouse port to the backpanel
connector of the Switch marked "PC2 MSE".

c) VGA Video

Connect PC#1's video output to the backpanel connector of the Switch marked "TO PC1 MON". Connect PC#2's video output
to the backpanel connector of the Switch marked "TO PC2 MON".

Connect PC#1’s Monitor A video output to the backpanel connector of the Switch marked “PC1 MON A” and connect
PC#1’s Monitor B video output to the backpanel connector of the Switch marked “PC1 MON B”. Repeat this step for PC’s #2,
#3, and #4.

d) Audio (Audio models only)

Connect the Microphone inputs of the PC’s to the Switch using a stereo cable male/male with 3.5 mm plugs to connectors on
the Switch marked “TO PC 1 MIC “ and “TO PC 2 MIC”. Connect the speaker outputs of the PC’s to the Switch using a stereo

Connect the mouse inputs of the PC's to the Switch using 6 pin PS/2 male/male extension cables. Connect PC#1's

Connect the keyboard inputs of the PC's to the Switch using 6 pin PS/2 male/male extension cables. Connect

Connect the Video outputs of the PC's to the Switch using 15 pin HDD15 male/female extension cables.

Or in the case of the V2, V3, and V4 series MegaSwitch

275 Marcus Blvd. Ste-J, Hauppauge, NY 11788-2022 USA

Tel: [phone] Fax: [phone]

www.vetra.com email: [e-mail]



They may be ordered from

cable male/male with 3.5 mm plugs at connectors the Switch marked “TO PC 1 SPKR” and “TO PC 2 SPKR”.

2. Connect a Workstation to the Switch:

a) PS/2 Keyboard

b) PS/2 Mouse

c) VGA Monitor

"MONITOR IN".

Connect the VGA Monitor A to the 15-pin HDD connector on the back panel of the Switch marked “MON A IN”. Repeat for
Monitors B, C, and D.

d) Audio (Audio models only)

and connect to the speakers to the connector marked “AUDIO INPUTS SPKR IN”.

OPERATION

1. Power Up Sequence:

There is no separate power control for the switch. The switch derives its power when either one of the two PC’s that are
connected to the switch are powered up. A Power Jack marked “+5VDC IN” on the back panel of the Switch is provided in
case an external power supply is needed. A separate power source may be required if the keyboard and PS/2 mouse
being used draws more current than be provided from a single PC source.

Note:

Optical PS/2 mice draw as much as 100 ma of current.

2. PC Selection:

a) Keyboard “Hot Key” Selection (available on all models):

then pressing and releasing the top row keyboard keys 1 or 2. The number keys must be released before the Scroll Lock
key. Switching takes place on the release of the Scroll Lock Key, which also rearms the keyboard selection mechanism.
When selection of PC#1 or PC#2 is completed, observe on the front panel of the switch that the appropriate green "SEL"
indicator is on.

b) Front Panel Selection:

Connect the keyboard to the 6-pin DIN connector on the front panel of the Switch marked "KBD IN".

Connect the mouse to the 6-pin DIN connector on the front panel of the Switch marked "MSE IN".

Connect the VGA monitor to the 15-pin HDD connector on the backpanel of the Switch marked

Or in the case of the V2, V3, and V4 series MegaSwitch

Connect the microphone to the connector on the Switch marked “AUDIO INPUTS MIC IN”

Some of the new Internet keyboards on the market can draw as much as 500 ma of current. Also the new

To select an active PC, first hold down the Scroll Lock Key,

1) Next PC (available on all Standard models):

located on the front panel of the MegaSwitch.

2) Direct Entry (available on DE models only):

for the appropriate PC desired.

To select another PC, press the “NEXT PC” pushbutton

To select another PC, press the “PC SELECTION” pushbutton

Systems Corporation 275 Marcus Blvd. Ste-J, Hauppauge, NY 11788-2022 USA

Vetra

Tel: [phone] Fax: [phone]

e-mail:[e-mail] http://www.vetra.com