Vestil CYL-LT-1-HR User Manual
Table of Contents 3/11/2020 CYL-LT-1MANUAL
Vestil Manufacturing Co.
Web: www.vestilmfg.com e-Mail: info@vestil.com
Limited Warranty…...……..…………………………………………………………………………………….. 7
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868
Fax: (260) 665-1339
CYL-LT-1-HR & CYL-LT-1-PN Cylinder Lifts
Instruction Manual
Receiving Instructions
After delivery, remove the packaging from the product. Inspect the product closely to determine
whether it sustained damage during transport. If damage is discovered, record a complete description
of it on the bill of lading. If the product is undamaged, discard the packaging.
NOTE: The end-user is solely responsible for confirming that product design, use, and maintenance
comply with laws, regulations, codes, and mandatory standards applied where the product is used.
Technical Service & Replacement Parts
For answers to questions not addressed in these instructions and to order replacement parts,
labels, and accessories, call our Technical Service and Parts Department at (260) 665-7586. The
department can also be contacted online at http://www.vestilmfg.com/parts_info.htm
.
Electronic copies of Instruction Manuals
Additional copies of this instruction manual may be downloaded from
https://www.vestil.com/page-
manuals.php.
Specifications……………………………………..……………………………………………………………... 2
Signal Words….…………………………………………………………………………………………………. 2
Safety Instructions…………………………………………………………………………..………………….. 2
FIG. 1: CYL-LT-1-HR exploded view & bill of materials…………………………………………………..… 3
FIG. 2: CYL-LT-1-PN exploded view & bill of materials…………………………………………………..… 4
Using the Lifter…………………………………………………………………………………………………... 5
Record of Satisfactory Condition……………………………………………………………………………… 6
Inspections & Maintenance……………………………………………………..……………………………… 6
Labeling Diagram……...………………………………………………………….…………………………….. 6
Table of Contents
Table of Contents Copyright 2020 Vestil Manufacturing Corp. 1 of 7
Table of Contents 3/11/2020 CYL-LT-1MANUAL
Overall dimensions
(W X D x H)
Uniform
capacity
46cm x 61cm x 203cm
136.4kg
44.1 kg
18in. x 24in. x 80in.
46cm x 61cm x 203cm
300 lb.
136.4kg
93 lb.
42.3 kg
W
D
H
SPECIFICATIONS
Dimensions, capacity, and net weight information appears in the following table:
Model Wheel type
CYL-LT-1-HR Hard rubber
a
CYL-LT-1-PN Pneumatic
18in. x 24in. x 80in.
300 lb.
SIGNAL WORDS
This manual uses SIGNAL WORDS to draw attention to uses of the product that could result in personal
injuries, as well as the probable seriousness of those injuries. Other signal words call attention to uses
likely to cause property damage. Signal words used in this manual appear below along with the definition of
each word.
Identifies a hazardous situation which, if not avoided, WILL result in DEATH or
SERIOUS INJURY. Use of this signal word is limited to the most extreme situations.
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or
SERIOUS INJURY.
Identifies practices likely to result in product/property damage, such as operation that
might damage the product.
SAFETY INSTRUCTIONS
Vestil strives to identify all foreseeable hazards associated with the use of its products. However,
material handling is dangerous and no manual can address every conceivable risk. Ultimately, the most
effective way to prevent injury is to apply sound judgment whenever using this device.
Material handling is dangerous and could result in serious personal injuries or death.
• Read and understand the entire manual before using or servicing this lifter. DO NOT use this
device until you read and understand the entire instruction manual. Read the manual to refresh your
understanding of proper use and maintenance procedures.
• This lifting device must only be used by designated persons and lifting device inspectors.
Maintenance and test personnel should only use this device when necessary to perform their duties.
• DO NOT use this lifter if it is damaged, malfunctioning, or missing parts.
• DO NOT modify the product in any way without first obtaining written approval from Vestil.
Unapproved modifications automatically void the LIMITED WARRANTY and might make the product
unsafe to use.
• DO NOT exceed the capacity.
• DO NOT remove or obscure any label. Confirm the placement and legibility of all labels shown in the
LABELING DIAGRAM on p. 6. DO NOT use this device UNLESS all labeling is easily readable from a
reasonable distance.
• Inspect the lifter before each use. See INSPECTIONS AND MAINTENANCE on p. 6. If repairs are
necessary, only use manufacturer-approved replacement parts.
• DO NOT use the lifter to transport any cylinder that does not seat securely in the brackets. DO NOT
transport a cylinder unless it is securely held by the ratchet strap. The cylinder should not be able to slide
through the strap.
• ONLY raise the cylinder a few inches from the floor when transporting it. When transporting a cylinder up-
or-downhill, always remain uphill to the lifter. DO NOT move the lifter up or downhill unless you can easily
control the lifter. Although the CYL-HLT is equipped with 2 locking casters, these locks will NOT hold the
lifter in place on an incline and will not stop the lifter as it rolls downhill.
• DO NOT leave a raised cylinder unattended. ALWAYS lower the cylinder before leaving it.
• DO NOT store cylinders on the lifter. Unload the lifter and store cylinders in designated facilities.
Net weight
97 lb.
Table of Contents Copyright 2020 Vestil Manufacturing Corp. 2 of 7
Table of Contents 3/11/2020 CYL-LT-1MANUAL
Item
Part no.
Description
Qty.
Item
Part no.
Description
Qty.
Flat washer, low carbon,
USS, zinc plated, 3/8”
Pulley, 3/16” cable, 21/2”
OD, 1/2” ID
Hex bolt, gr. A, zinc
plated, 1/4”-20 x 11/2”
Nylon lock nut, gr. 2, zinc
finish, 1/4”-20
Extended prong cotter
pin, zinc finish, 1/8”x 11/2”
6
30-001-246
Strap, dual ratchet strap
1
18
13-025-037
Handle, black, 1” ID
2 7 16-112-019
Axle, CYL-D, BFSJ-KIT-A8.625
1
19
16-016-104
Bracket, handle, mounting
1
Hex bolt, gr. A, zinc
plated, 1/4”-20 x 4”
Flat washer, USS, zinc
plated, 1/4”
Hex bolt, gr. A, zinc finish,
/8”-16 x 4”
Hex bolt, gr. A, zinc-plated, 3/8” –
16 x 1”
Hex nut, gr. A, zinc
plated, 3/8”-16
Flat washer, zinc plated,
SAE, 1/2”-1.062” OD
FIG. 1: CYL-LT-1-HR
16-006-194
Exploded Parts Diagram &
Bill of Materials
1
16-514-133 Weldment, base, upright 1
2
16-527-008 Weldment, pulley assembly 1
3
16-542-001 Assembly, winch and wire 1
4
16-514-134 Weldment, strap height adjuster 1
5
16-525-033 Weldment, handle 1
8
16-132-310 Wheel, 10” x 2.5”, 16mm steel hub 2
9
21-112-003 Pin,
10
65077 Cotter pin, zinc plated,
11
11105
12
37024 Lock nut, Nylon insert,
1
/2” x 115/16” retaining clevis 3
1
/8” x 11/4” 3
3
/8”-16 3
13
14
15
16
17
20
21
22
23
3
24
33008
99-027-005
11009
37018
65078
11019
33004
11119
36106
33086
3
5
2
1
5
2
4
8
2
2
8
Table of Contents Copyright 2020 Vestil Manufacturing Corp. 3 of 7
Loading...