Vestil CYL-HLT User Manual

rev. 2/26/2014 CYL-HLT, manual.doc
Vestil Manufacturing Co.
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339
www.vestilmfg.com e-mail: sales@vestil.com
CYL-HLT series Cylinder Lifter and Transporter
After delivery, immediately remove the packaging from the product in a manner that preserves the packaging and maintains the orientation of the product in the packaging; then inspect the product closely to determine whether it sustained damage during transport. If damage is discovered during the inspection, immediately record a complete description of the damage on the bill of lading. If the product is undamaged, discard the packaging.
NOTES:
1) Compliance with laws, regulations, codes, and non-voluntary standards enforced in the location where the product is used is exclusively the responsibility of the owner/end-user.
2) Vestil is not liable for any injury or property damage that occurs as a consequence of failing to apply either: a) the instructions in this manual; or b) information provided on labels affixed to the product. Neither is Vestil responsible for any consequential damages sustained as a result of failing to exercise sound judgment while assembling, installing, using or maintaining this product.
Table of Contents
Product Specifications……………………………………..…………………………………………………………….. 2 Hazard Identification: Explanation of Signal Words….……………………………………………………………….. 2 Safety Guidelines…………………………………………………………………………..…………………….………. 2 FIG. 1: CYL-HLT exploded parts diagram & bill of materials………………………………………………………… 3 Use Instructions…………………………………………………………………………………………………………... 4 Inspections & Maintenance……………………………………………………………………………………………… 5 Label Placement Diagram……...……………………………………………………………………………………….. 5 Limited Warranty…...…………………………………………………………………………………………………….. 6
Copyright 2014 Vestil Manufacturing Corp. 1 of 6
rev. 2/26/2014 CYL-HLT, manual.doc
P
RODUCT SPECIFICATIONS
Dimensions and other product specifications of standard wrapping machine models appear in the following
table:
Model Wheel type Overall dimensions
CYL-HLT
Phenolic swivel
casters
37in. x 44in. x 126in.
94cm x 112cm x 320cm
Uniform capacity
300 lb.
136.4kg
Net weight
266 lb.
121kg
HAZARD IDENTIFICATION: explanation of signal words
This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable seriousness of those injuries, if the product is misused in the ways described. Other signal words call attention to uses of the product likely cause property damage.
The signal words used appear below along with the meaning of each word:
Identifies a hazardous situation which, if not avoided, WILL result in DEATH or
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or
Indicates a hazardous situation which, if not avoided, COULD result in MINOR or
Identifies practices likely to result in product/property damage, such as operation
Each person who assembles, uses, or maintains this product should read the entire manual and fully understand the directions in advance. If after reading the manual you do not understand an instruction, ask your supervisor or employer for clarification, because failure to adhere to the directions in this manual might result in serious personal injury.
SERIOUS INJURY. Use of this signal word is limited to the most extreme situations.
SERIOUS INJURY.
MODERATE injury.
that might damage the product.
SAFETY GUIDELINES
Vestil diligently strives to identify foreseeable hazards associated with the use of its products. However, no manual can address every conceivable risk. The end-user ultimately is responsible for exercising sound judgment at all times.
Failure to read and understand the entire manual before using or servicing the product
constitutes misuse. Read the manual to refresh your understanding of proper use and maintenance
procedures. If this product is used improperly or carelessly, the operator and/or bystanders might sustain serious personal injuries:
DO NOT exceed the maximum rated load. Inspect the lifter before each use. Remove it from service if the inspection reveals damage such as: 1)
cracked welds; 2) corrosion, extreme wear, or other condition that affects the ability of the product to support weight; 3) significantly worn or damaged wheels/casters; 4) missing or damaged ratchet straps. DO NOT use the product until it is restored to normal condition. ONLY use manufacturer-approved replacement parts.
DO NOT use the lifter to transport any cylinder that does not seat securely in the brackets. DO NOT transport a cylinder unless it is securely held by the ratchet strap. The cylinder should not be able to
slide through the strap.
ONLY raise the cylinder a few inches from the floor when transporting it. When transporting a cylinder up-or-
downhill, always remain uphill to the lifter. DO NOT move the lifter up or downhill unless you can easily control the lifter. Although the CYL-HLT is equipped with 2 locking casters, these locks will NOT hold the lifter in place on an incline and will not stop the lifter as it rolls downhill.
DO NOT leave a raised cylinder unattended. ALWAYS lower the cylinder completely. DO NOT store cylinders on the lifter. DO NOT remove or obscure any label. All product labels must be readable and undamaged. (See p. 7). DO NOT modify the lifter in any way. Unauthorized modifications automatically void the limited warranty
(see p. 6) and might make the lifter unsafe to use.
Copyright 2014 Vestil Manufacturing Corp. 2 of 6
Loading...
+ 4 hidden pages