Vestamatic VRS WISO Crystal Control Manual
G
VRS WISO Crystal Control
85700621 H1
Radio controlled weather station with integrated wind / lux sensor
Compatible with all Vestamatic motors of VRS-Line VL-ME-WISO-35/45
The weather station is ready mounted on a mounting bracket.
– Contact a professional electrician to install the control sys-
tem, because the control system requires a power supply of
230VAC, 50 Hz.
– Check the control system for signs of mechanical damage
after unpacking. If you notice any shipping damage, do not start
up the control system and notify your supplier immediately.
– The control system should only be used for the purpose spec-
ified by the manufacturer (refer to the operating instructions).
Any changes or modifications thereof are not permissible and
will result in loss of all warranty claims.
– If the control unit or the connected sunshade cannot be oper-
ated without presenting a hazard, it must be switched off and
prevented from being switched on unintentionally.
– When performing work on the windows, controls or connected
shades, protect them against unauthorised or unintentional
operation.
Crystal Control
Art.-no.:
01180002
Short description
Safety precautions
VRS WISO
VRS WISO Crystal Control Art.-no.: 01180002
Radio controlled weather station with integrated wind/lux sensor
and incl. mounting bracket.
Installation and Operating Instructions
Assembly and installation
The sensor unit must be installed and connected by a professional electrician.
1. When deciding where to install the sensor unit, ensure that the wind
speed and sun intensity readings, taken at the mounting location, are
similar to those, taken on the shading device.
WARNING!
Do not mount the sensor unit in the shade, or shelter, of the
extended shading device. The wall mount should be attached with the sensor unit column pointing upwards as
shown in figure 1.
2. Attach the wall mount using the supplied installation kit.
3. Connect the power supply cable to the sensor cable according to the
wiring diagram.
4. If necessary, adjust the sensor unit (a) so, that together with the lux
sensor (b), it captures maximum sun intensity.
Figure 1
Scope of delivery
1 × VRS WISO Crystal Control
1 × power supply 230VAC / 12VDC, 1 A
1 × surface-mount housing for power supply
1 × magnet
6 × dowel including screws
6 × chandelier terminals
Technical data
Power supply: 12 VDC, 25 mA, 0.3 W
Impulse voltage withstand level: 2.5 kV
Radio frequency: 868 MHz
Wind speed sensor:
Measuring range: 3 ... 17 m/s
Lux sensor:
Measuring range: 0 ... 40 kLux
Range: max. 30 m
Operating temperature: -15 °C (+5 °F) to +60 °C (140 °F)
Connectable VRS motors: max. 10 (VL-ME-WISO-35/45)
Protection degree: IP 44
Material (plastic parts): UV-stabilised polycarbonate
Conformity:
This product conforms to the basic requirements of the R&TTE Directive
1999/5/EC. The declaration of conformity can be found on the web page:
www.vestamatic.com
p
Conformity
WARNING!
Risk of injury due to improper installation and commissioning.
Improper installation and commissioning may lead to per-
sonal injury or property damage.
Therefore:
– When connecting the device, observe the currently valid
VDE standards (in particular DIN VDE 0100/0700), your local
power company’s regulations and the current accident prevention regula tions.
– Connect the control in accordance with the wiring diagram.
Wiring diagram
Art.-Nr.: 85700621 H1 • Vestamatic GmbH • Dohrweg 27 • D-41066 Mönchengladbach • www.vestamatic.com
1/4
G
Subject to modifications.© Vestamatic GmbH
VRS WISO Crystal Control
Sensors and functionality
The control includes a wind sensor and a lux sensor, and is paired to one
or max. 10 Vestamatic VRS motors. The motor can also be paired with
several wall transmitters or 5 channel transmitters at the same time.
The sensor of the control will send commands to the motor and will retract
or extend your sunshades depending on the sun and wind conditions.
Wind sensor: If the wind speed exceeds the threshold value, the sun-
If the measured wind intensity is below the threshold
Lux sensor: If the measured sun intensity exceeds the threshold value
If the measured sun intensity is below the threshold value,
Rain sensor:
(optional sensor) is detected.
The VRS WISO Crystal Control should be wall-mounted, and a magnet
should be used to configure the sensor of the control.
Instead of pressing a mechanical button, you hold the magnet close to the
housing (correct location is marked by the words PROG POINT) as shown
below.
Through the transparent housing you can see several LEDs. Green LEDs
show the current sun intensity, and red LEDs show the current wind speed.
shade will retract in order to avoid damage. At this point
it’s not possible to control the motors with your local VRS
transmitters.
value, the motor will be controlled via sun or manually by
transmitter after a delay of 16 minutes.
for at least 2 minutes, the sensor of the control will extend
the sunshade completely or to a specific individual position.
This specific position can be individually set on all motors.
the sunshade will be retracted after a delay time (16 minutes) completely.
If a rain sensor is connected, sunshades will be retract
Overview operating elements
if rain
LED feedback
The control contains different visible LEDs.
8 green LEDs show the sun intensity and threshold.
8 red LEDs show the wind speed and threshold.
1 red LED shows if programming mode is activated.
1 yellow LED shows if rain / frost function is activated.
LEDs are automatically turned off after 60 minutes when it’s dark (= 0 kLux)
Pressing the PROG POINT quickly will turn on the LED feedback for 5 min-
utes.
If wind / sun / rain function is activated during night, the LEDs are temporary
turned on as long as any function is active.
During normal operation, the 8 sun and 8 wind LEDs are turned on from
the bottom to the top, to indicate the current sun and wind value.
Red / green LED row:
One LED on each row is flashing. This slow flashing indicates the threshold values. This makes it easy to see if the current wind or sun is close to
exceeding the threshold value.
If the current value is above the threshold value, the LED will flash fastly.
If the current value is above the threshold value for a longer time and acti-
vates the function, it’s indicated with a rapid flashing “threshold LED”. The
LED will flash rapidly until current value is low, OFF-delay is exceeded and
function is inactive again.
If the complete row of all red LEDs are flashing quickly, this means that the
wind sensor hasn’t been working for 48 hours. Wind function is active as
long as wind sensor is marked as “broken”, the sun protection will be retracted.
Yellow LED:
The single yellow LED is normally turned off.
Yellow LED is also light when PROG POINT is pressed. This is a visual
feedback that magnet is held in correct position.
The single yellow LED will flash fast when rain function is activated
rity function and all motors are locked in upper position.
as secu-
.
1. Magnet
2. PROG POINT
3. Wind sensor
4. Lux sensor
5. Single red LED (lit during programming mode)
6. Single yellow LED (lit when magnet is hold close to PROG POINT, etc.)
7. Wind: 8 red LEDs show wind speed
8. Sun: 8 green LEDs show sun intensity
Single Red LED:
The single red LED is normally turned off.
The single red LED is turned on if you enter the “Programming mode”.
Wind sensor (wind alarm)
If the current value is above the threshold value, the red LED will flash
fastly. All sunshades are retracted and locked in upper position.
If you try to control the motor via remote, the motor will move shortly down
and up.
Wind sensor (48 hour protection)
If wind sensor doesn’t detect any wind pulses for 48 hours, wind sensor is
marked as “broken”, and wind function is activated.
All sunshades are retracted and locked to the upper position. If you try to
control the motor via remote, the motor will move shortly down and up.
This state is also indicated by flashing all red LEDs as long as sensor is
marked as “broken”.
By full turn of the propeller, the sensor is marked as fixed again, and
motors are unlocked again. Other functions, such as sun function or
manual UP / DOWN commands, can now be activated again.
Additional accessories
The control can be connected to a rain sensor.
Rain sensor RD +1 °C (32 °F), Article-no.: 01083560
The rain sensor will retract the sunshades and protect against rain and frost.
2/4
G
Art.-Nr.: 85700621 H1 • Vestamatic GmbH • Dohrweg 27 • D-41066 Mönchengladbach • www.vestamatic.com
Subject to modifications.© Vestamatic GmbH
Loading...