Vestamatic Rolltec Plus G/S Installation And Operating Instructions Manual
Rolltec Plus G/S
Roller Shutter Control
Art.-no. 01805050
Installation and Operating Instructions
Safety precautions
– Contact a professional electrician to install the control
Ä
– Check the control system for signs of mechanical
– The control system should only be used for the purpose
– If the control unit cannot be operated without presenting
– When performing work on the windows, controls or
as well as for setting of the DIP switches on the rear
panel of the device, because the power supply requires
a power supply of 230VAC, 50 Hz.
damage after unpacking. If you notice any shipping
damage, do not start up the control system and notify
your supplier immediately.
specified by the manufacturer (refer to the operating
instructions). Any changes or modifications thereof are
not permissible and will result in loss of all warranty
claims.
a hazard, it must be switched off and prevented from
being switched on unintentionally.
connected shades, protect them against unauthorised
or unintentional operation.
G
- 40 -
Contents
Introduction General page 43
Manual mode page 44
Automatic mode page 45
Programming General page 46
the basic Summer/winter time page 47
functions Current time page 48
Note page 49
Up time page 50
Down time page 51
Random generator page 52
Programming Week function page 53
the special Astro function / Run time correction page 54 – 57
functions Astro function – Germany page 58
Astro function – Europe page 59
Reverse function page 60
Example for DIP switch setting page 61
Contents
G/S functions General page 62
Functional description broken glass sensor page 63
Functional description sun protection page 64
Setting the response (sun intensity) page 65
Troubleshooting page 66
Installation Notes for professional electricians page 67 – 68
Installation instructions / Technical data page 69
Wiring diagram page 70
Installation broken glass sensor page 71 – 72
Installation lux sensor page 73 – 74
Wiring diagram Inside back cover
Overview operating elements Inside back cover
- 41 -
G
G
- 42 -
General Introduction
The delivery extent of the control includes the following items:
1. Cover cap
2. Control
3. Supporting frame for control
4. Adjustment tool
5. JUNG Cover frame, 1-fold, “CD 500”
In case of power failure, the entire display starts flashing. Yet, the
previously programmed times remain saved for several years.
The times or functions, you have previously programmed, can be
checked by performing a quick run (i. e. g. test of the sun protection).
Press the time and day button simul ta ne ously for 3 seconds to activ ate
the quick run. The time function will now run 60 times faster. Shortly
tap the time and day button simul ta ne ously to stop the quick run.
Introduction Manual mode
The control features a selector switch with which manual mode (H) or
automatic mode (A) can be selected.
Push the selector switch to (H), all the way to right until you hear the
“click”, in order to activate the manual mode.
All automatic functions are now disabled. Pressing the up or down
button will move the roller shutters up or down.
Simply press the opposite button to stop the motion, i.e.:
press the down button, if the roller shutter is moving up,
press the up button, if the roller shutter is moving down.
Accurate positioning of the roller shutter is guaranteed because the
roller shutter will only move up or down again after the up or down
button has been pressed.
- 43 -
G
G
- 44 -
Automatic mode Introduction
Push the selector switch to (A), all the way to the left until you hear
the “click”, in order to activate the automatic mode.
The automatic mode is now activated and the roller shutter will
move up and down at the programmed times. Regardless of the
programmed times, it is still possible to move the roller shutter up
and down by pressing the up or down button and the programming
remains unaffected.
If you press the up or down button longer than 2 seconds, the roller
shutter moves up or down.
Simply press the opposite button to stop the motion, i.e.:
press the down button, if the roller shutter is moving up,
press the up button, if the roller shutter is moving down.
The roller shutter will only move up or down again after the up or
down button has been pressed.
By simply pushing the selector switch to manual mode (H), the automatic mode can be interrupted for an extended period of time.
After selecting automatic mode again, the control will execute the
last pending command from the automatic mode. The last pending
command will also be executed when resetting after power failure.
Basic functions General
After the installation has been completed correctly (for instructions
please see pages 67 to 74), you can start programming.
IMPORTANT!
x
Please note that the control cannot be programmed in case
of power failure.
Carefully pull to remove the cover cap and press the reset button with
the delivered adjustment tool or something else suitable.
Pressing the reset button will activate the default times pre-programmed
by the manufacturer.
Current time – 0ß8:0ß0
Up time – 0ß6:0ß0
Down time – 2ß0:0ß0
On the following pages, you will find instructions how to customize
these times to your personal requirements.
- 45 -
G
G
- 46 -
Summer/winter time Basic functions
The display will indicate which time has been set.
The (S) in the upper left hand corner of the display stands for summer
time.
(0S9:0ß0)
The (W) in the upper right hand corner of the display stands for
winter time.
(0ß8:0W0)
If the present setting is incorrect and does not correspond with the
current time, you can simply update the time by pressing the summer/
winter button. The selected setting will appear in the display and the
time will be changed by one hour.
Basic functions Current time
By operating the combination of set and time button you can set the
current time.
Setting the time can be performed as follows:
1. Press the set button first and keep it pressed, then:
A. Press the time button and keep it pressed to fast forward the
time.
B. Shortly tap the time button to slow forward the time.
or
2. Press the time button first and keep it pressed, then:
A. Press the set button and keep it pressed to fast reverse the
time.
B. Shortly tap the set button to slow reverse the time.
- 47 -
G
G
- 48 -
Note Basic functions
The control is delivered with the following manufacturer’s default up
and down times (day function is activated):
Daily up time – 0ß6:0ß0 p.m.
Daily down time – 2ß0:0ß0 a.m.
Please find the manufacturer’s default DIP switch settings in the
tables on page 58 and page 61.
IMPORTANT!
x
It is important to push the selector switch
manual-mode” to
to perform the following programming steps.
Check the current setting. If the selector switch is not set on
(A), correct the setting by pushing it all the way to the left
until you hear the “click”.
auto matic mode (A), in order to be able
“automatic/
Basic functions Up time
By operating the combination of set and up button you can set the
up time.
Setting the up time can be performed as follows:
1. Press the set button first and keep it pressed, then:
A. Press the up button and keep it pressed to fast forward the
up time.
B. Shortly tap the up button to slow forward the up time.
or
2. Press the up button first and keep it pressed, then:
A. Press the set button and keep it pressed to fast reverse the
up time.
B. Shortly tap the set button to slow reverse the up time.
The display will now indicate the set value. Once the programming
buttons are no longer operated, the display will indicate the current
time again. Tapping the up button will check the set value and the
display will again indicate the previously set up time. After approx.
2 seconds, the display will indicate the current time again.
- 49 -
G
G
- 50 -
Loading...