Page 1
590-1640-501A/SL-20861_REV4
1
vertiv™ MPH2™ rack Pdu
Quick Installation Guide
VERTICAL MPH2 RACK
PDU MOUNTING
A vertical MPH2 rack PDU can be
mounted by using either the supplied
in-line brackets or the supplied
mounting buttons.
Determine which mounting method
best suits your rack and install the
necessary hardware in the rack. The
rack PDU should be mounted so that its
input power cord exits at either the top
or bottom of the rack.
In-line bracket installation
Install the brackets by inserting the legs
of each bracket into the slots on each
end of the rack PDU.
Insert two of the supplied spring nuts
into the appropriate T-slot on the rack
frame. Use a small, pointed object to
position the spring nuts into place.
Hold the bottom of the rack PDU
assembly over the desired mounting
holes in the rack frame or rack
manufacturer’s bracket and insert the
fasteners into the PDU bracket. Leave
the fasteners slightly loose.
Position the top PDU bracket over the
desired mounting holes and insert its
fasteners. Tighten all rack PDU bracket
fasteners.
Button mount installation
Use a Torx™ screw to attach the
supplied button mounts to the rear of
the rack PDU.
NOTE: Only use the mounting buttons
provided with the MPH2 rack PDU. Using
other mounting buttons may damage the
rack PDU.
Find the keyhole slots in the rack
frame or install the rack manufacturer’s
keyhole slot brackets in the desired
location in the rack.
Insert each of the attached mounting
buttons into the large opening of a
keyhole slot. Slide the assembly down
into the narrow portion of the keyhole
slots to lock the PDU in place.
HORIZONTAL MPH2 RACK
PDU MOUNTING
Attach the supplied brackets to
each side of the rack PDU. Attach
each bracket to the rack using the
appropriate screws for your rack.
Button Mount Installation
Button
Mount
Keyhole Slot
Back View Front View
Spring Nuts in
Rack Frame
In-line Bracket Installation
In-line
Bracket
A
B
C
Horizontal Installation
Page 2
VertivCo.com | Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA
© 2017 Verti v Co. All righ ts reser ved. Verti v and the Verti v logo are tra demarks or r egister ed tradem arks of Vertiv C o. All other n ames and l ogos refe rred to are tra de names , tradema rks or
registe red trade marks of their respec tive owner s. While eve ry precaution has been taken to ensure accuracy an d comple teness he rein, Vert iv Co. assumes no res ponsibi lity, and dis claims all
liability, for damages resulting from use of this information or for any errors or omissions. Specications are subject to change without notice.
590-1640-501A/SL-20861_REV4
2
vertiv™ MPH2™ rack Pdu
Quick Installation Guide
MPH2 Rack PDU Setup
NOTE: It is recommended that all devices
powered through the MPH2 rack PDU
be turned o and unplugged from input
power sources.
1. Connecting to a network
Connect an Ethernet cable
from your network to the RPC2
Communications Module’s
Network port.
2. Connect Devices’ Power
Cords
NOTE: Record where each powered
device is connected using the
branch and receptacle IDs on the
MPH2 rack PDU for reference.
Connect the devices’ input power
supply cables to the MPH2 rack
PDU’s receptacles.
3. Creating a Rack PDU Array™
Use an Ethernet cable to connect
the Link port of the first MPH2 rack
PDU to the Network port of the
second MPH2 rack PDU; repeat for
up to two more MPH2 rack PDUs.
4. Connecting an SN sensor
Use an RJ45 compatible cable
to connect an SN sensor to
the Sensor port of the RPC2
Communications Module.
5. Connecting a console server
Use an RJ45 compatible cable to
connect a serial console server
to the Serial port of the RPC2
Communications Module.
6. Connecting a Basic Display
Module
Use an RJ45 compatible cable to
connect an optional Basic Display
Module (BDM) to the Display port
of the RPC2 Communications
Module.
7. Turning on the MPH2 rack
PDU
Ensure all circuit breakers on the
unit are in the Off position. Connect
input power to the MPH2 rack PDU.
Press the circuit breaker switches
into the On position. Verify voltage
on the LCD and that the LEDs are
illuminated. Connect each device’s
input power supply cable and verify
the current draw on the LCD.
8. Viewing IP address, MAC
address and Firmware
version
Use the arrow keys under the LCD
of the MPH2 rack PDU to highlight
the Information icon, then press
the select key, which is located
between the arrow keys. Use an
arrow key to highlight the Network
icon and press the select key again.
The LCD displays the IP address,
MAC address and RPC2 module
firmware version.
Serial
Port
RPC2 Communications Module Ports
MPH2 Rack PDU Configuration
(Vertical Model Shown)
�
Network
Basic Display Module
Console Server
or Switch
Sensor
Additional PDUs
Powered Devices
2
3
4
5
6
Sensor
Port
Display
Port
Link
Port
Network
Port
Loading...