Vertiv EXS 0010kTH1AFN01, Liebert EXS 20kVA, EXS 0015kTH1AFN01, EXS 0010kTH1AFN02, EXS 0020kTH1AFN01 User Manual

...

Download

Page 1

Liebert® EXS 10-20kVA

User Manual

Page 2

EXS 10-20kVA

UNINTERRUPTIBLE POWER SUPPLY

USER MA

10H52260UM60 – rev. 1

NUAL

Page 3

EXS

All rights, including rights of translation, reproduction in any form or other usage of this document, or any part of it, are reserved. Transgressors will be liable for damages. All rights, including rights deriving from the granting of patent or registration of utility, model or design, are reserved. Delivery subject to availability. The Manufacturer reserves the right to make changes and/or improvements to the product without prior notice and without incurring obligations.

EXS ma

2 User Manual 10H52260UM60 - Rev. 1 - 10/2017

differ from the model displayed on the front cover.

Page 4

EXS

Special Declaration

Safety of Personnel

1. This product must be installed by qualified professionals, engineers appointed by the manufacturer or an

authoriz

personnel.

2.Take the time to read this product manual and the safety precautions thoroughly before inst

commissioni

the safety of personnel.

3. This product is not intended for use with life support system

4. Ne

inju

Product Safety

ed agent. Failure to observe this condition may result in product malfunction, and compromise the safety of

ng this product. Failure to observe this condition may result in product malfunction, and compromise

ver attempt to dispose of the internal and external batteries in fire as they may explode, leading to seri

ries, or even death.

alling and

ous

1. If the product is to be stored or unused for extended periods, place the equipment in a clean, dry environment

within the specified temper

2. This product should be used in an appropriate operating environment. Consult the Site Preparation section for

ormation about the ideal operating and maintenance environment for this product

inf

3. This product is not designed for use in conditions and/or environments where:

 The temperature and relative humidity are outside the specified limits

 It is subject to vibration or shocks

 It is exposed to the presence of conductive dust, corrosive gases, salts, or inflammable gases

 It is exposed to heat sources or strong electro-magnetic interference

Disclaimer

VERTIV may not be held accountable or responsible for defects and malfunctions arising for the following reasons:

 Application range or operating environment outside the specified limits

 Unauthorized modification, incorrect installation or operation

 Force majeure

 Other actions not in compliance with the instructions in this manual

ature range

User Manual 10H52260UM60 - Rev. 1 - 10/2017 3

Page 5

EXS

Safety Precautions

Always observe the following safety symbols!

Used to alert the user to the risk of death or severe injury should the unit be used improperly.

Used to alert the user to the risk of injury or damage to the equipment should the unit be used improperly.

Used for instructions that the user must read carefully and observe, even if failure to do so may not result in damage.

This manual contains information concerning the installation and operation of single UPS modules and parallel systems of the Vertiv EXS 10kVA-20kVA UPS.

Read this manual thoroughly before installing, using and servicing the UPS.

Warning

This UPS has been designed for use in commercial and industrial environments. Installation restrictions or additional measures may be required to prevent disturbances.

Conformity and standards

This product complies with the Directives 2014/35/EU (low voltage safety) and 2014/30/EU (EMC), and the following UPS product standards: * IEC/EN62040-1+A1:2013 General safety requirements for UPS * IEC/EN62040-2:2006 EMC * IEC/EN62040-3 Performance requirements and test methods For more details, refer to Chapter 10 . Continued compliance requires installation in accordance with these instructions and the use of manufacturer approved accessories only.

Warning: high earth leakage current

The unit must be connected to earth before it is connected to its AC mains input and battery power supplies. This equipment is fitted with an EMC filter. The earth leakage current ranges from 0 to 1000 mA. Transient and steady state earth leakage currents, which may occur when the equipment is started, should be taken into account when se4lecting the instantaneous RCCB or RCD devices. RCCB devices that are sensitive to unidirectional DC pulses (Class A) and immune to transient state current pulses must be selected. It is also necessary to take into account that the load earth leakage currents will be borne by the RCCB or RCD. The equipment must be earthed in compliance with the local electrical code of practice.

Warning

When selecting the UPS system upstream distribution protection devices, ensure that comply with the specifications indicated in 3.1.4 , and with the local electrical regulations.

Warning: backfeed protection

This UPS is fitted with a dry contact for use with an external automatic disconnecting device (not supplied) in order to prevent the UPS voltage from being fed back to the input terminals through the rectifier or bypass static switch circuit. A label must be placed on or near the all external primary input supply disconnecting devices to warn service personnel that the circuit is connected to a UPS. The text of the label must have the following meaning: Risk of voltage backfeed! Isolate the UPS, then check for hazardous voltages between all terminals, including the protective earth, before working on this circuit.

4 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 6

EXS

ral safety precautions (For users)

Gene

Like other types of large power equipment, the UPS and battery circuit breaker box/battery cabinet contain high voltages.

This equipment meets the IP20 standard, and other safety panels are fitted inside the equipment.

The UPS may be operated in complete safety, provided the general instructions and the steps recommended in this manual

are followed.

Multip

le power inputs (For users)

This UPS system receives power from more than one source. All DC and AC power sources must be disconnected before

servicing.

This UPS includes several circuits that are energized by high AC as well as DC voltages. Check for voltage with both AC and

DC voltmeters before working inside the UPS.

User serviceable compon

All equipment maintenance and servicing procedures involving internal access require the use of a tool and should be carried

out by trained personnel only. There are no user-serviceable parts behind the covers that require a /key for removal.

Batt

ery voltage: 320Vdc - 540Vdc (For service personnel)

All battery maintenance and servicing procedures require the use of tools and should be carried out by trained personnel only.

Take special care when working with the batteries associated with this UPS. When connected together, the battery terminal

voltage will exceed 320Vdc and is potentially lethal.

Battery manufacturers supply details of the necessary precautions to be observed when working on, or in the vicinity of, a

large bank of battery cells. These precautions should be followed scrupulously at all times. Special attention should be paid to

the recommendations concerning local environmental conditions and the provision of protective clothing, first aid and fire-

fighting facilities.

Warning

When the internal fuse of the UPS is damaged, it must be replaced with fuse having the same electric parameters by qualified

personnel.

Important

The area housing the communication board contains static sensitive components, therefore it is necessary to adopt all the

appropriate ESD-proof measures before accessing this area.

ents (For service personnel)

Warning

In order to satisfy the conditional short circuit current rating, Icc at 10kA symmetrical rms, the specified upstream breakers

must comply with an IEC 60947 series standard.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 5

Page 7

This Manual describes the following devices

Product Model

Liebert EXS 10kVA (Standrad UPS) EXS 0010kTH1AFN01

Liebert EXS 15kVA (Standard UPS) EXS 0015kTH1AFN01

Liebert EXS 20kVA (Standard UPS) EXS 0020kTH1AFN01

Liebert EXS 10kVA (UPS with side cabinet) EXS 0010kTH1AFN02

Liebert EXS 15kVA (UPS with side cabinet) EXS 0015kTH1AFN02

Liebert EXS 20kVA (UPS with side cabinet) EXS 0020kTH1AFN02

EXS

6 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 8

EXS

Contents

Chapter 1 Overview ......................................................................................................................................................................................................... 9

1.1 Features .......................................................................................................................................................................................................................................................................... 9

1.2 Design Conce

1.3 Parallel System ......................................................................................................................................................................................................................................................... 12

1.4 Operating Modes .................................................................................................................................................................................................................................................... 13

1.5 Battery Management

1.6 Battery Pro

pt ......................................................................................................................................................................................................................................................... 9

............................................................................................................................................................................................................................................ 15

tection .................................................................................................................................................................................................................................................. 16

Chapter 2 Mechanical Installation ............................................................................................................................................................................ 1

2.1 Precautions

2.2 Transportation ......................................................................................................................................................................................................................................................... 17

2.3 Tools .............................................................................................................................................................................................................................................................................. 18

2.4 Unpacking .................................................................................................................................................................................................................................................................. 19

2.5 Initial Inspection ..................................................................................................................................................................................................................................................... 21

2.6 Environmental Requirements

2.7 Mechanical Requirements

2.8 Installation Drawings .......................................................................................................................................................................................................................................... 23

Chapter 3 Electrical Installatio n ............................................................................................................................................................................... 2

3.1 Connecting the Power Ca

3.2 Wiring the Signal Cables .................................................................................................................................................................................................................................... 31

Chapter 4 Operator Control and Dis play Panel ................................................................................................................................................... 35

4.1 Introduction .............................................................................................................................................................................................................................................................. 35

4.2 LCD Menu Structure

4.3 LCD Screen Types .............................................................................................................................................................................................................................................. 40

4.4 Prompt Window ..................................................................................................................................................................................................................................................... 46

4.5 UPS Alarm Messa

bles ........................................................................................................................................................................................................................ 25

ge List .................................................................................................................................................................................................................................. 46

Chapter 5 Oper ating Procedure s ............................................................................................................................................................................. 5

5.1 Brief Introduction ................................................................................................................................................................................................................................................... 50

5.2 UPS Start-up Procedures

5.3 Procedures for Transferring Between Opera

5.4 UPS Shut-down Procedures ........................................................................................................................................................................................................................... 58

5.5 REPO ............................................................................................................................................................................................................................................................................ 58

5.6 Automatic Re

5.7 Language Selection ............................................................................................................................................................................................................................................. 59

5.8 Changing the Current Da

5.9 Setting the Password .......................................................................................................................................................................................................................................... 61

Chapter 6 Battery ......................................................................................................................................................................................................... 6

6.1 Introduction .............................................................................................................................................................................................................................................................. 65

6.2 Safety ........................................................................................................................................................................................................................................................................... 65

6.3 UPS Ba

6.4 Precautions For Installation Design ........................................................................................................................................................................................................... 68

6.5 Battery Installation Environment a

6.6 Battery Pro

User Manual 10H52260UM60 - Rev. 1 - 10/2017 7

start ................................................................................................................................................................................................................................................ 59

ttery .............................................................................................................................................................................................................................................................. 67

ting Modes............................................................................................................................................................... 54

te And Time ..................................................................................................................................................................................................... 60

nd Number of Batteries ......................................................................................................................................................... 68

Page 9

6.7 Battery Installation and Connections ........................................................................................................................................................................................................ 69

6.8 Designing the Battery Room .......................................................................................................................................................................................................................... 70

6.9 Battery Maintena

6.10 Disconnecting or Connecting Internal Battery Terminals ........................................................................................................................................................... 71

6.11 Disposal of Used Batteries ............................................................................................................................................................................................................................. 72

Chapter 7 Para llel System and LBS System .......................................................................................................................................................... 7 3

7.1 General ......................................................................................................................................................................................................................................................................... 73

7.2 System Installation Procedures

7.3 Operating Procedures for Parallel Systems ........................................................................................................................................................................................... 75

7.4 LBS System .............................................................................................................................................................................................................................................................. 78

nce .......................................................................................................................................................................................................................................... 70

EXS

Chapter 8 Opti ons ......................................................................................................................................................................................................... 8

8.1 List of Options ......................................................................................................................................................................................................................................................... 82

8.2 Option Introduction ............................................................................................................................................................................................................................................. 82

Chapter 9 Service And Maintena nce ...................................................................................................................................................................... 9

9.1 Fan Maintenance ................................................................................................................................................................................................................................................... 98

9.2 Battery Maint

9.3 Cleaning the UPS .................................................................................................................................................................................................................................................. 99

9.4 Checking the UPS Status ................................................................................................................................................................................................................................. 99

9.5 Checking the UPS Functions ......................................................................................................................................................................................................................... 99

Chapter 10 Specifications ........................................................................................................................................................................................ 100

10.1 Conformity and sta

10.2 Environmental Characteristics................................................................................................................................................................................................................. 100

10.3 Mechanical Specifications .......................................................................................................................................................................................................................... 100

10.4 Electrical Specifications (Inpu

10.5 Electrical Specifications (Intermediate DC Circuit) ....................................................................................................................................................................... 101

10.6 Electrical Specifications (Inverter Output) ........................................................................................................................................................................................ 102

10.7 Electrical Specifications (Bypass Input) .............................................................................................................................................................................................. 102

Appendix 1 LCD Parameter Settings .................................................................................................................................................................... 103

enance .......................................................................................................................................................................................................................................... 98

ndards .......................................................................................................................................................................................................................... 100

t Rectifier) ............................................................................................................................................................................................ 101

Appendix 2 Glossary .................................................................................................................................................................................................. 1

Appendix 3 Haz ardous Substances And Content ............................................................................................................................................ 106

8 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 10

EXS

Chapter 1 Overview

This section provides a short introduction to the Liebert EXS 10kVA - 20kVA UPS (hereafter referred to as “the

UPS”), covering features, design concept, parallel system, operating mode, battery management and battery

protection.

1.1 Features

The UPS is connected between a critical load (e.g. a computer) and the mains power supply to provide high quality

power for the loads. The UPS provides the following advantages:



Increased power quality

The UPS protects its output against the variations in the input power supply by means of the intelligent controller.



Improved noise rejection

Due to the use of AC-DC-AC conversion, noise on the input power supply is effectively filtered, so that the load is

provided with a “clean” power supply.



Mains failure protection

If the input power fails, the UPS switches to battery operating mode so that the power supply to the loads is not

interrupted.



Compatible with two output modes

3-in 3-out (factory default) and 3-in 1-out (by installing an optional 3-in 1-out copper bar kit). Only authorized

personnel are permitted to change the wiring method and modify the corresponding parameters using the VERTIV

setting software.

1.2 Design Concept

System Design

This section introduces the working principle of the single UPS module. The UPS adopts AC-DC-AC conversion (as

shown in Figure 1-1). The first stage conversion (AC-DC) uses a three-phase, high frequency rectifier to convert the

three-phase input voltage into a stable DC bus voltage.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 9

Page 11

EXS

Input

Output

Bypass input

Mains input

Rectifier input switch

Maintenance bypass switch

Static switch

Bypass input switch

Rectifier

Battery

Figure 1-1 Block diagram illustrating the working principle of a UPS single module

Battery charger

Inverter

Automatic inverter switch

Maintenance bypass

UPS output

Output switch

The UPS has its own battery charger and adopts advanced temperature compensation technology to effectively

prolong the battery service life. The inverter is principally based on the use of large power IGBTs, and adopts

advanced SVPWM control technology to reconvert the DC bus voltage to AC voltage.

When the mains is normal, the rectifier and inverter work together to supply the loads and charge the battery.

When the mains is outside normal limits, the rectifier stops working, and the battery supplies power to the loads

through the inverter. If the battery voltage falls to end of discharge (EOD) voltage and the mains has not yet

returned within the normal limits, the UPS will shut down (if the system uses split bypass configuration and the

bypass is normal, the system will transfer to bypass). The battery EOD voltage is pre-set. When the mains is

abnormal, the battery will continue to supply the UPS until the battery voltage reaches to EOD level, whereupon the

UPS shuts down; this period is known as the 'Backup Time'. The duration of the backup time depends on the battery

capacity and the loads.

Bypass

Thanks to the intelligent control function provided by the ‘Static Switch’ module (as shown in Figure 1-1), which

includes the controllable electronic switch, the loads may be supplied either by the inverter or the bypass. Under

normal operating conditions, the loads are supplied by the inverter, in which case the automatic inverter switch on

the inverter side is closed. In the event of an overload (after the overload delay period has elapsed) or inverter

failure, the inverter switch is opened, and the 'Static Switch' module transfers the loads automatically to the bypass.

In normal operating state, in order to guarantee the uninterrupted transfer between inverter and bypass, the inverter

output must be synchronized with the bypass.

Therefore, when the bypass frequency is within the synchronization range, the inverter control circuit will

synchronize the inverter output frequency with the bypass frequency and phase.

The UPS is also equipped with a manual maintenance bypass switch that can be used to shut the UPS down during

maintenance. In this condition, the bypass will supply the critical loads directly via the maintenance bypass.

Note

When the load is supplied by the bypass or maintenance bypass, the power quality & availability will be unregulated.

10 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 12

EXS

System Control Principle

Normal operation

Normal mode: In this condition, the UPS mains input supply is within normal limits, the rectifier and inverter operate

normally, the load is supplied by the inverter, the battery circuit breaker is closed, and the battery is in the stable

floating charge state.

(Parallel System) Note: As the individual UPS module outputs are connected in parallel, the system checks that the

inverter control circuits are perfectly synchronized with one another and with the bypass in terms of both frequency

and phase, and that the output voltages are the same. The current supplied to the load is automatically divided

among the UPS units. A warning message appears while synchronization is in progress.

Mains abnormal

When the mains fails or is abnormal, the rectifier will stop working automatically, and the system will transfer to

battery output (through the inverter). The length of the operation time in battery mode depends on the load and the

battery capacity. During this period, if the battery voltage falls to the EOD level before the mains supply has

returned within normal limits, the inverter will stop working automatically, and the UPS operator control and display

panel will display the corresponding alarm messages. If the system uses split bypass configuration and the bypass is

normal, the system will transfer to bypass.

Mains recovery

When the mains returns within normal limits within the permissible time, the rectifier will start automatically (at this

point its output power will increase gradually) and supply the load and charge the battery again. This means that

the power supply to the load will not be interrupted.

Disconnecting the battery

To disconnect the external battery from the UPS system during maintenance, use the external isolation device. In

this condition, the battery backup function will not be available in the event of a mains failure, but none of the other

UPS functions and performance will be affected.

UPS module failure

In the event of an inverter failure, automatic inverter switch failure, or if the output fuse blows, the load will

automatically transfer to the bypass, and the output power supply will not be interrupted. Should this condition

occur, please contact your local VERTIV customer service centre for technical support.

(Parallel System) In the event of a fault on a UPS module, it will automatically exit the parallel system. If the system

is still capable of providing the power required by the load, the remaining modules will continue to supply the load

without interruptions. If the remaining modules are no longer capable of fulfilling the power requirements, the load

will automatically transfer to the bypass.

Overload

If the inverter is overloaded or the inverter current remains outside the specifications (refer to Table 10-6) longer

than the specified time, the load will automatically transfer to the bypass without any interruption in the power

supply to the load. If both the overload and the current are reduced to a level within the specified range, then the

load will be re-transferred to the inverter. In the event of an output short circuit, the load will be transferred to the

bypass, and the inverter will shut down. The transfer is determined primarily by the characteristics of the system

protection device.

In both the situations listed above, the UPS operator control and display panel will display the corresponding alarm

messages.

(Parallel System) The control logic system constantly monitors load requirements and controls the power supplied

by each UPS module. If an overload condition persists for longer than a pre-set period and the number of active

modules is unable to satisfy load requirements, the load will transfer to the bypass. The load is re-transferred to the

inverter if the power is reduced to a value that can be sustained by the number of active modules in the system.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 11

Page 13

Maintenance bypass

The UPS is equipped with a second bypass circuit, known as the maintenance bypass, which provides a safe

working environment for the engineers to carry out regular maintenance or repair the UPS system, while providing

unregulated mains supply to the loads. The maintenance bypass can be activated manually selected by closing the

maintenance bypass switch, and disconnected by setting the switch to OFF.

Warning

If the UPS system consists of two or more UPS modules, and the load capacity exceeds the single module capacity, do not

use the internal maintenance bypass switch.

UPS Power Supply Switch Configuration

Figure 1-2 illustrates the block diagram of the UPS module. The UPS may be connected in split bypass (where the

bypass is supplied by a separate mains input source) or common input configuration. In the split bypass

configuration, the static bypass and maintenance bypass share the same independent bypass power supply. Where

a separate power source is not available, the input supply connections of the bypass input switch (Q2) and rectifier

input switch (Q1) should be linked together (these terminals are linked before delivery) so that the bypass input and

rectifier input use mains power from the same source.

During the normal UPS operation, all switches should be closed, with the exception of the maintenance bypass

switch Q3.

EXS

Figure 1-2 UPS power supply switch configuration

Circuit Breaker

The external battery shall be connected to the UPS via the circuit breaker.

1.3 Parallel System

Up to four UPS modules may be parallel-connected to form a parallel system and increase the system capacity and

reliability. The load is shared equally between the parallel connected UPS modules.

Also, two UPS modules or parallel system may be used to form a dual bus system (LBS). Each UPS module or

parallel system has an independent output. Output synchronization is achieved through the LBS cable, thus

enabling seamless load transfer between the two systems.

12 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 14

EXS

Parallel System Features

1. The hardware and software of a parallel system are identical to those of the individual modules. The parallel

system is configured by modifying the respective settings in the configuration software or via the control panel.

2. Parallel cables are connected in a ring, providing both system reliability and redundancy. LBS cables are

connected between any two UPS modules of each bus. The intelligent parallel logic provides the user with maximum

flexibility. For example, the UPS modules in a parallel system can be shut down or started up in any order. Transfers

between normal mode and bypass mode of operation are seamless and self-recoverable, i.e, when the overload is

cleared the system will revert automatically to its original operating mode.

3. The total load of the parallel system can be queried from the LCD screen on each UPS

Parallel System Requirements

A group of paralleled modules behave as if it were one large UPS with the advantage of providing increased

reliability. To ensure that all modules are utilised equally and to comply with relevant wiring rules, the following

requirements apply:

All UPS modules must be of the same rating and must be connected to the same bypass sour

2.The bypass a

If any RCD devices are installed they must be set-up appropriately and located upstream of the common neutra

line i

nput terminal. Alternatively, the device must monitor the protective earth current of the system. Refer to

nd rectifier input sources must be connected to the same neutral line input te

Warning: high earth leakage current before Contents.

module.

ce.

rminal.

1.4 Operating Modes

The UPS features the following operating modes:



Normal mode



Battery mode



Bypass mode



Maintenance mode



ECO mode



Parallel redundancy mode (system expansion)



LBS system mode



Common battery string mode

Normal mode

As shown in Figure 1-3, the mains is rectified by the UPS rectifier and then inverted by the inverter to supply

uninterrupted AC power to the loads. At the same time, the charger will charge the battery.

Mains input

Rectifier input switch

Rectifier

Inverter

Automatic inverter switch

UPS output

Output switch

Battery

User Manual 10H52260UM60 - Rev. 1 - 10/2017 13

Battery charger

Figure 1-3 Normal operating mode line diagram

Page 15

Battery mode

As shown in Figure 1-4, the operating mode where the battery provides the backup power supply to the loads

through the rectifier and inverter is called battery mode. In the event of a mains failure, the system will transfer

automatically to battery mode with no interruption in the power supply to the load. When the mains power supply is

restored, the system will re-transfer automatically to normal operating mode without any manual intervention, and

with no interruption in the power supply to the load.

EXS

Rectifier

Battery

Note

The battery cold start function may be used to switch the UPS on in Battery (charged) mode directly during mains failure. This means that the battery power supply can be used independently to improve the availability of the UPS.

Inverter

Figure 1-4 Battery operating mode line diagram

Automatic inverter switch

UPS output

Output switch

Bypass mode

As shown in Figure 1-5, in normal mode, in the event of an inverter failure, inverter overload or inverter manual shut

down, the static switch will transfer the load from the inverter side to bypass side, with no interruption in the power

supply to the load. In this case, if the inverter and bypass are not synchronized, there will be a transitory interruption

in the power supply to the load (not exceeding 20ms).

Static switch

Bypass input

Bypass input switch

Output switch

UPS output

Figure 1-5 Bypass operating mode line diagram

Maintenance mode

As shown in Figure 1-6, if it is necessary to service the UPS or carry out maintenance work on it, you may use the

manual maintenance bypass switch to transfer the load to maintenance bypass, with no interruption in the power

supply to the load. This maintenance bypass switch is fitted in all UPS modules and rated for full load of one module.

Maintenance bypass switch

Bypass input

Figure 1-6 Maintenance operating mode line diagram

Maintenance bypass

UPS output

ECO mode

If ECO mode is selected, all the power switche

s and the circuit breaker are closed, and the system selects the

bypass as the preferred source of power for the load, in order to save energy. When the bypass supply frequency

and voltage are within normal limits (adjustable), the load is powered by the bypass, with the inverter on stand-by;

when the bypass voltage and/or frequency is outside these pre-defined and adjustable limits, the system will

transfer to the inverter output. In this mode, the system can charge the battery normally.

14 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 16

EXS

Bypass input

Mains input

Rectifier input switch

Static switch

Bypass input switch

InverterRectifier

UPS output

Output switch

Automatic inverter switch

Battery

Figure 1-7 ECO operating mode line diagram

Warning

The load is not protected against distortion on the mains voltage waveform in ECO mode.

Battery charger

Parallel redundancy mode (system expansion)

For higher capacity or higher reliability, or both, the outputs of multiple UPS modules can be programmed for

directly paralleling while a built-in parallel controller in each UPS module ensures automatic load sharing. The

parallel system may consist of up to four UPS modules. For the operating principle diagram of parallel redundancy

mode, see Figure 7-1.

LBS mode

A dual bus system consists of two independent UPS systems, each containing one or more parallel UPS modules.

The dual bus system provides high reliability, which makes it suitable for use with loads having multiple input

terminals. In the case of single-input loads, an STS may be installed to power the load. For the operating principle

diagram of LBS mode, see Figure 7-4.

Common battery string mode

In this mode, when the UPS modules (up to four UPS units) are connected in parallel, they share the same battery

string thus providing cost and space savings.

Note

Never use batteries having different brands, type or capacities in the same system. Common battery string mode is suitable

for parallel systems only, and is not compatible with LBS mode.

1.5 Battery Management

The following battery management functions are set by the service engineer using the VERTIV setting software.

Normal Function

1. Constant current boost charge

Uses a constant current (within battery charging limit) to charge the battery. This function can be used for fast

battery capacity recovery. It is possible to modify the value of the charge current.

2. Constant voltage boost charge

Uses a constant voltage to charge the battery. This function can be used for fast battery capacity recovery. In the

case of VRLA batteries, the maximum boost charge voltage should not exceed 2.4V/cell.

3. Float charge

User Manual 10H52260UM60 - Rev. 1 - 10/2017 15

Page 17

This charging method is used for maintaining the battery at full capacity. The float charge voltage is generally low.

This function can be used to compensate for capacity loss due to battery self-discharging, and to recover battery

capacity.

In the case of VRLA batteries, the float charge voltage should be between 2.2V/cell and 2.3V/cell.

4. Automatic transfer to float charge

When the charge current is less than the 'Threshold of Equalize Charge to Float Charge’ value, the charger will

automatically transfer from boost charge to float charge. When the boost charge time exceeds the 'Equalize Charge

Protect Time Limit', the charger will be forcibly transferred to float charge in order to protect the battery.

5.Float charge temperature compensation (o

This fu

nction must be used together with the battery temperature detection device. The VERTIV battery

temperature sensor is a standard option designed to satisfy your requirements.

EOD

protecti

When the batte

is disconnected in order to avoid further battery discharge. The EOD voltage may be set to between 1.6V/cell and

1.85V/cell (VRLA).

ttery low pre-warning time

The battery low pre-warning time may be set to between 2min and 30min. The default setting is 2min.

mum battery discharge time

Maxi

When the battery is discharged at low current levels for extended periods, it will result in excessive discharge and

may even cause irreparable damage, for this reason it is essential to set-up a maximum battery discharge time in

order to protect it. This limit value is set-up by the service engineer using the VERTIV setting software.

9. Maximum boost charge protection ti

o protect against the battery overcharge damage caused by long time boost charge, it is essential to set-up a

protection time a protect time limit This limit value is set-up by the service engineer using the VERTIV setting

software.

ry voltage falls to the EOD level, the the battery converter shuts down automatically and the battery

ptional)

EXS

Battery Temperature Compensation

The UPS system also features a battery charge temperature compensation function. When the ambient temperature

is increased, the DC bus voltage (which charges the battery) will be reduced correspondingly to provide optimal

charging voltage for the battery, thus prolonging the battery service life time. This function must be used together

with the VERTIV battery temperature detection device (standard option).

1.6 Battery Protection

The following battery protection functions are set by the service engineer using the VERTIV setting software.

Battery low pre-warning

The battery low pre-warning occurs before the EOD. The time can be set to between 2min and 30min.

EOD protection

When the battery voltage falls to the EOD level, the battery converter shuts down automatically. The EOD voltage

may be set to between 1.6V/cell and 1.85V/cell (VRLA).

16 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 18

EXS

Chapter 2 Mechanical Installation

This section provides a brief introduction to the UPS mechanical installation procedures, including the precautions,

initial inspection before installation, environmental requirement, mechanical requirement and installation diagram.

2.1 Precautions

This section describes the environmental and mechanical requirements and mechanical considerations that must be

taken into account when planning the positioning and cabling of the UPS equipment.

Because no two sites are the same, this section does not provide the detailed installation procedures, and is only

intended to act as a guide for the general procedures and practices that should be carried out by the installing

engineer, so that they can handle the specific situation at the site correctly.

Warning: professional installation required

1. Do not dismantle the packaging without the permission of an authorised service engineer.

2. The UPS should be installed by an authorised engineer in accordance with the information provided in this section.

Warning: battery danger

Take special care when installing batteries. When connecting batteries, the battery terminal voltage will reach 320Vdc,

which is fatal to human beings.

1. Always wear safety glasses to protect the eyes from being damaged by arcing.

2. Remove all the metal items, including finger rings, watch, etc.

3. Use tools with insulated handles.

4. Wear rubber gloves.

5. If batteries are damaged or leak electrolyte they must be replaced. Place the battery into the container that can withstand

sulphuric acid and dispose of it according to the local regulations.

6. In the event of contact with electrolyte, wash the affected are with abundant clean water immediately.

2.2 Transportation

Rail and sea shipping are the recommended transportation methods. If road transportation is unavoidable, choose

roads that are less bumpy in order to protect the equipment.

The UPS cabinet is heavy (see Table 10-3 for the weight). We recommend using mechanical equipment such as an

electric forklift to unload and move the equipment to the place closest to the installation site.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 17

Page 19

EXS

2.3 Tools

Warning

1. For reasons of safety, all installation tools used on live components must be insulated.

2. The tools listed in Table 2-1 are for reference only; please adapt to the actual requirements for on-site installation and

connection.

Name Drawing Name Drawing

Electric hand drill

Slotted screwdriver

Stepladder

Drill

Claw hammer

Table 2-1 Tools

Adjustable wrench

Cross head screwdriver

Forklift

Wire cutting pliers

Diagonal cutting pliers

Insulating shoes

Electrician’s knife

Insulating tape

Crimping pliers

Insulated torque wrench

Multimeter

Antistatic gloves

Cable ties

Insulating gloves

Heat shrinkable tube

Torque screwdriver

Clip-on ammeter

18 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 20

EXS

2.4 Unpacking

Unpack the UPS and battery packages under the supervision of an authorized service engineer.

Proceed as follows:

emove the cart

1. R

emove the packing strap and lift the whole carton upwards, as shown in Figure 2-1.

on.

Removing carton from standard UPS

Removing carton from UPS with side cabinet

Figure 2-1 Removing cartons

2. Remove the fixing structural parts from the bottom pallet (see Figure 2-2), do not throw them away. Next, use the

orklift (inserting the forks at the points illustrated in Figure 2-2) to move the cabinet close the installation site.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 19

Page 21

EXS

Remove the fixing structural parts

Inserting direction

Standard UPS UPS with side cabinet

Figure 2-2 Removing the bottom pallet

Remove the fixing structural parts

Inserting

3. After moving the cabinet to the installation site, you raise the adjustable feet and use the castors to move the

cabinet to its final installation position, finally, rotate the adjustable feet until they are in contact with the floor. See

Figure 2-3 for the finished installation.

Note

1. It is not necessary to install the fastening structural parts of the bottom pallet in the case of UPS with side cabinet

2. In the case of standard UPS with internal batteries, simply secure the fastening structural parts removed

in step 2 to the cabinet bottom (See right drawing); in the case of standard UPS without internal batteries,

install the fastening structure parts to both the left and right hand sides (See left drawing) based on the

right drawing to avoid tipping.

UPS without internal batteries UPS with internal batteries

Figure 2-3 Completed installation

20 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 22

EXS

2.5 Initial Inspection

Before installing the UPS, carry out the following inspections:

1.Ensure that the UPS equipment room meets the environmental requirements specified in the product te

specifications, especially the ambient temper

Unpack the U

and out

side of the UPS and battery for any shipping damage. If there is any damage, report it to the carrier

immediately.

3.Verify the UPS label and confirm that the UPS model conforms to the information indicated on it

ttached to the rear of the door. The UPS model, capacity and the main parameters are marked on the label.

PS and battery under the supervision of an authorized service engineer. Visually inspect the

2.6 Environmental Requirements

Selecting the UPS Location

The UPS should be located in a cool, dry, clean-air indoor environment with adequate ventilation, and should be

located on concrete or other non-flammable, flat surfaces. The surrounding environment should be free from

conductive powders (such as metallic powder, sulphide, sulphur dioxide, graphite, carbon fibre, conductive fibre,

etc.), acid mist or other conductive media (strongly ionized substances). The environmental specifications should

comply with relevant international standard & specifications and the operating range (see Table 10-2) specified in

this manual.

The UPS uses forced cooling by internal fans. Cooling air enters the UPS through the ventilation grills at the front of

the cabinet and is expelled through the ventilation grills at the back of the cabinet. Do not obstruct the ventilation

holes (ventilation grills). The rear of the UPS should be kept a distance at least 200mm from the wall to avoid

blocking the UPS heat dissipation, thus reducing the UPS internal temperature and improving the UPS life.

If necessary, install indoor extractor fans to aid cooling-air flow and avoid temperature build-up in the installation

area.

chnical

ature, ventilation conditions, and the levels of dust.

inside

. The UPS label is

Note

Note 1: When the battery cabinet is installed near the UPS, the maximum allowable ambient temperature is dependent on the battery rather than the UPS. Note 2: If the UPS is operating in ECO mode, the power consumption will be less than in Normal mode. A proper air conditioning system shall be selected according to the normal operating mode.

Selection the Battery Location

Batteries generate a certain amount of hydrogen and oxygen at the end of the charging cycle, so the fresh air

volume of the battery installation environment must meet the EN50272-2001 requirements.

The ambient temperature is the main factor that affects the battery capacity and life. The normal operating

temperature of the battery is 20°C. If the ambient temperature is higher than 20°C, the battery life will be reduced. If

it is lower than 20°C, the battery capacity will be reduced. Under normal operating conditions, the acceptable

ambient temperature for the battery is 15°C to 25°C. The ambient temperature of the battery must be maintained

constant, and the battery must be kept away from heat sources and air outlets.

The battery may be installed inside the dedicated battery cabinet, which shall be positioned close to the UPS. If the

battery is placed on the raised floor, brackets shall be installed under the floor, just as for the UPS. In the case of

rack-mounted batteries or batteries that are installed remotely from the UPS, the battery circuit breaker shall be

installed close to the battery, and the cable lengths shall be kept to a minimum.

Storage

Should the UPS not be installed immediately, it must be stored in its original packaging in a location where it is

protected against excessive humidity and heat sources (see Table 10-2). The battery must be stored in a dry and

cool place with good ventilation. The most suitable storage temperature is between 20°C and 25°C.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 21

Page 23

EXS

Warning

Recharge the battery at regular intervals during storage in accordance with the manufacturer’s instructions. During the

charge process, connect the UPS temporarily to the mains and activate the battery by recharging it.

2.7 Mechanical Requirements

Moving the Cabinet

Warning

1. Ensure that the load capacity of the lifting equipment used to move the UPS cabinet is sufficient.

2. The UPS is fitted with castors. When removing the UPS from the shipping pallet, take care to prevent it from sliding.

Ensure that sufficient personnel and lifting equipment are available when removing the shipping pallet.

3. Due to the weight of the UPS cabinet, the castors may only be suitable for use on flat surfaces.

4. The centre of gravity of the UPS cabinet is high, take care to prevent it tipping over when moving it

5. The cabinet must never be suspended vertically.

Caution

Take special care when moving the battery cabinet with the batteries installed, making sure that each battery string has

been secured and keeping movements to a minimum.

Ensure that the UPS weight does not exceed the load capacity of the lifting equipment. For information about the

weight of the UPS, refer to Table 10-3.

The UPS may be moved using a forklift truck or similar lifting equipment.

The castors may be used when it is necessary to move it over short distances.

Clearance

Because the UPS is not fitted with lateral grilles, there is no special clearance requirement on either side.

In addition to any local regulations, in order provide sufficient space for routine operations, such as tightening the

power terminals inside the UPS, it is recommended that clearance around the front of the UPS should be sufficient

to enable free passage of personnel with the door fully open. In addition, it is necessary to leave a clearance of at

least 200 mm at the rear of the cabinet in order to permit adequate circulation of the hot air expelled by the UPS.

Cable Access Mode

UPS cable access is from the rear of the cabinet.

For details, refer to 3.1.10 and 3.2.8 .

22 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 24

EXS

2.8 Installation Drawings

Figure 2-4 Front/side/bottom view of the standard UPS (unit: mm)

User Manual 10H52260UM60 - Rev. 1 - 10/2017 23

Page 25

EXS

Figure 2-5 Front/side/bottom view of the UPS with side cabinet (unit: mm)

24 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 26

EXS

Chapter 3 Electrical Installation

This section principally introduces the UPS electrical installation procedures, including the power cable and signal

cable connecting procedures and methods.

Once the mechanical installation procedure is complete, it is necessary to connect the power and signal cables to

the UPS. All signal cables, whether or not they are shielded, must be kept away from the power cables.

Warning

1. Do not switch the UPS on before the authorised service engineer arrives.

2. The UPS should be routed by an authorised engineer in accordance with the information provided in this section.

3.1 Connecting the Power Cables

System Configuration

The system power cable dimensions shall meet the following requirements:

UPS input cable

The UPS input cable dimension differs depending on the UPS power ratings and input AC voltages, provided that it

meets the requirement of maximum input current, including the maximum battery charge current, see Table 3-1.

UPS bypass and output cable

The UPS bypass and output cable size differs depending on the UPS power rating and output AC voltages, provided

that it meets the requirement of nominal output or bypass current, as shown in Table 3-1.

Battery cable

Each UPS is connected to the respective battery positive pole, negative pole and neutral line by three cables . The

battery cable dimension differs depending on the UPS power ratings, provided that it meets the battery discharge

current requirement when the battery voltage nears the EOD level, as shown in Table 3-1.

Maximum Steady State AC and DC Currents

The power cable must be selected according to the current and voltage values indicated in Table 3-1, as well as the

local wiring regulations, as well as taking environmental conditions (temperature and physical media) into

consideration; refer to Table 3B in IEC 60950-1.

Table 3-1 Max. steady state AC and DC currents

Rated current (A)

UPS power

(kVA)

10 (3-in 3-out ) 22 16 15 14 35/35/15 M6 3

10 (3-in 1-out ) 22 48 45 42 35/35/15 M6 3

15 (3-in 3-out ) 33 23 22 21 52/52/25 M6 3

15 (3-in 1-out ) 33 69 66 63 52/52/25 M6 3

20 (3-in 3-out ) 44 31 29 28 70/70/30 M6 3

20 (3-in 1-out ) 44 93 87 84 70/70/30 M6 3

Max. input

current

Output/bypass current

1,2

at full load

380V 400V 415V

Battery discharge

current (+, -, N) at

min. battery voltage

Bus stud bolt/nut

specification

Input/batte

ry/output/

bypass

cable

Recommende

d torque

(N.m)

When selecting the battery cables, a max. volt drop of 4Vdc is permissible at the current ratings given in Table 3-1. Avoid coiling

the cables as this would increase the electromagnetic interference (EMI).

1. Input mains current for rectifier and bypass.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 25

Page 27

2. Non-linear load (like switch power) affects the design of output and bypass neutral line. The neutral line current may exceed

the rated phase current, at most 1.5 times of the rated phase current.

Recommended CSA of UPS Cables

The recommended CSA of the UPS cables is listed in Table 3-2.

Table 3-2 Recommended CSA of the UPS cable (unit: mm2, ambient temperature: 25°C)

Model Input Output Bypass Neutral line Earth cable Battery

10 (3-in 3-out ) 10 10 10 10 10 10

10 (3-in 1-out ) 10 10 10 10 10 10

15 (3-in 3-out ) 10 10 10 10 10 10

15 (3-in 1-out ) 10 16 16 16 16 10

20 (3-in 3-out ) 10 10 10 10 10 16

20 (3-in 1-out ) 10 25 25 25 25 16

When the system is in common input configuration and in 3-in 1-out mode, because phase A powers the load, the input cable of

phase A must be selected according to Table 3-2. Input cables of phase B and phase C may refer to Table 3-2.

Selecting the UPS I/O Switch

Table 3-3 indicates the recommended UPS I/O switch capacity, the user may select it as required.

EXS

Table 3-3 Selecting the UPS I/O switch

Model Input port External input switch

(3-in 3-out )

(3-in 1-out )

(3-in 3-out )

(3-in 1-out )

(3-in 3-out )

(3-in 1-out )

Terminal block 32A (3P) 50A Terminal block 25A (3P)

Terminal block 32A (3P) 50A Terminal block 63A (1P)

Terminal block 50A (3P) 63A Terminal block 32A (3P)

Terminal block 50A (3P) 63A Terminal block 80A (1P)

Terminal block 63A (3P) 80A Terminal block 50A (3P)

Terminal block 125A (3P) 80A Terminal block 125A (1P)

Distance Between the UPS Connection Point and the Floor

See Table 3-4 for details.

Table 3-4 Min. distance between UPS connection point and floor

UPS connection point

Circuit breaker

Min. distance（mm）

Output port

External

output switch

Rectifier input 1000

Bypass input 1000

AC Output 1100

Battery 1100

PE terminal 1100

Notes

The following points are provided for general guidance only. If there are corresponding local regulations, such

regulations shall prevail.

26 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 28

EXS

1. The protective earth cable dimension shall be selected according to the AC power failure level, cable length and

otection type. The grounding wire connection must use the shortest possible connection route.

2. In the case of cables that are required to handle large current, it may be easier to use multiple smaller cables in

allel.

par

3. When selecting the battery cable dimension, it is important to take the current value in Table 3-1 into account and

mind that the maximum permissible voltage drop is 4 Vdc.

bear in

Avoid coiling the cables as this would increase the electromagnetic interfer

Power Cable Connecting Terminal

The rectifier input, bypass input, output and battery power cables are connected to the corresponding terminals, as

shown in Figure 3-2.

Protective Earth

The protective earth cable must be connected securely to the PE input terminal (see Figure 3-2) using the fastening

bolt. All the cabinets and cable troughs shall be earthed according to the local regulations. The earthing wires shall

be secured in order to prevent them coming loose from the fastening screws if they are pulled.

Warning

Failure to earth the various elements as directed may result in EMI, electric shock or fire risk.

ence (EMI).

External Protective Device

To ensure safety, it is necessary to install external circuit breakers on the UPS input and battery lines. Because no

two installations are the same, this section is only intended to provide general practical guidelines for installation

engineers. Qualified installation engineers should be aware of the local wiring regulations and any other related

information

Rectifier and bypass input power supply

overcurrent and short circuit protection

1. Input

Install suitable protective devices on the mains input supply distribution line. The protective devices should provide

functions such as overcurrent protection, short circuit protection, isolation protection and tripping upon backfeed.

When selecting the protective devices, consider the power cable current-carrying capacity, system overload

capacity (see Table 10-6 and Table 10-7) and the short circuit capacity of the upstream power distribution.

2. Split bypass configurat

If the UPS

adopts the split bypass configuration, independent protective device shall be installed on both the

ion

rectifier input and bypass input distribution lines.

Note

1. The rectifier input and bypass input must use the same neutral line.

2. In the case of IT grid systems, a 4-pole protective device must be installed on the UPS external power distribution line.

3. Earth fault protection

If the ups

tream input power supply his fitted with an RCD, it is important to take the transient state and steady state

earth leakage current upon the start-up of the UPS into account.

The RCCB shall meet the following requirements:



Be sensitive to DC unidirectional pulses (class A) in the power distribution network



Be immune to transient current pulses



Have an average sensitivity of 0.3A - 3A (adjustable)

The R

CCB symbols are shown in Figure 3-1.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 27

Page 29

EXS

Figure 3-1 RCCB symbols

The UPS is fitted with an internal EMC filter, therefore the protective earth cable leakage current is 0 - 1000mA. We

recommend confirming the RCD sensitivity of the upstream input power distribution and downstream power

distribution (to the load) lines.

External battery

The circuit breaker must be installed in order to protect external battery.

This circuit breaker is extremely important for the battery maintenance, and is generally installed close to the battery.

System output

The UPS output distribution line must be fitted with a protective device. The protective device must be different

from the input distribution protection switch and be able to provide overload protection (refer to Table 10-6 and

Table 10-7 ) .

Power Cable Connection Steps

For the UPS cable access mode, refer to 2.7.3 .

Connection terminals and cable routing method

Figure 3-2 shows the UPS power cable connection terminals. Figure 3-3 shows the power cable entry and routing

methods.

Note

1. Open the appropriate holes on the rear protective cover before routing the power cables. Install cable guards around the

rims of the hole to protect power cables against cutting.

2. Feed the power cables through the holes, then connect them to the corresponding terminals.

Figure 3-2 Power cable connection terminals (rear view)

28 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 30

EXS

Figure 3-3 Power cables wiring diagram (rear cable access)

Warning

1. Before connecting the cables, make sure that all the external and internal UPS power switches are set to OFF, and post the

appropriate warning signs to prevent inadvertent operation of the switches.

2. Measure the voltages between the UPS terminals, and the voltages between the terminals and earth.

rning

1. The earth cables and neutral line must be connected in accordance with local and national codes of practice.

2. Failure to observe this condition may result in electric shock or fire risk.

Power distribution mode

Based on the user's requirements, it is possible to select one of the following I/O cable connection configurations:

 3-in 3-out, common input configuration (factory default)

 3-in 3-out, split bypass configuration

 3-in 1-out, common input configuration

 3-in 1-out, split bypass configuration

Connecting th

1. 3

-in 3-out, common input configuration (factory default)

e system input

Refer to Figure 3-4, connect the AC input cables to the three copper shorting bars between the rectifier input

terminals (mA-mB-mC) and the bypass input terminals (bA-bB-bC) in the cabinet. Connect the input neutral line to

the terminal N in the cabinet. Make sure that the phase rotation is correct.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 29

Page 31

Note

Note that the common input copper shorting bars are fitted before delivery.

EXS

Figure 3-4 3-in 3-out, common input configuration cable connection (factory default)

2. 3-in 3-out, split bypass configuration

efer to Figure 3-5, remove the three copper shorting bars between the rectifier input terminals (mA-mB-mC) and

the bypass input terminals (bA-bB-bC). Connect the rectifier input cables to the rectifier input terminals (mA-mB-

mC) in the cabinet, and connect the bypass input cables to the bypass input terminals (bA-bB-bC) in the cabinet.

Connect the input neutral line to the terminal N in the cabinet. Make sure that the phase rotation is correct.

Figure 3-5 3-in 3-out, split bypass configuration cable connection

3. 3-in 1-out, common input configuration

r more details, refer to 8.2.7 .

-in 1-out, split bypass configurat

4. 3

r more details, refer to 8.2.7 .

ion

Connecting the system output

In the case of 3-in 3-out configurations, connect the system output cables between the output terminals (oA-oB-oC-

oN) and the load; whereas, in the case of 3-in 1-out configurations, connect the system output cables between the

30 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 32

EXS

output copper shorting bars (oA-oB-oC), oN and the load. Refer to Table 3-1 for the tightening torque values. Make

sure that the phase rotation is correct.

Warning

Prior to the service engineer's visit, if the load is not ready to be connected to the power supply, it is important to ensure the

terminals of the output cables are insulated safely

Connecting the batteries

If the external battery is required, ensure correct polarity between the battery string terminals and the circuit breaker, and between the circuit breaker and the UPS cabinet battery input terminals (Bat+, N, Bat-), i.e. (Bat

+) to (+), (Bat-) to (-) and (N) to (N).

This completes the connection procedure. At this point it is possible to replace the protective covers.

Note

After connection, take appropriate measures to seal the cable entry holes.

3.2 Wiring the Signal Cables

Overview

Depending on the specific on-site needs, the UPS requires auxiliary connections to manage the battery system

(including the external battery circuit breaker), communicate with a PC, provide alarm signals for external devices,

enable a remote EPO and/or the bypass back feed circuit breaker signal, and for parallel communication functions.

These functions are performed by the communication box in the UPS cabinet. As shown in Figure 3-6, the

communication box provides the following ports:

1. Intellislot port

2. Dry contact port

3. R

S232

port

4. Ethernet port (not used)

arallel/LBS port

5.P

EPO

6. R

port

SB port

Mult

ifunctional port

Figure 3-6 Illustration drawing of communication box ports

User Manual 10H52260UM60 - Rev. 1 - 10/2017 31

Page 33

Dry Contact Port

The UPS provides five dry contact ports. The silkprints of the five dry contact ports are 1 - 12. The pin layout of each

dry contact port is shown in Figure 3-7, and the port description is shown in Table 3-5.

Figure 3-7 Pins of dry contact ports

Table 3-5 Description of the dry contact ports

Silkscree

1 Output port1

2 Output port 2

3 Input port 1

4 Input port 2

Port name Pin NO. Pin name Meaning

REPO input

port*

LOW_BATTERY/ON_BATTE

/ON_BYPASS/UPS_FAULT/

Main backfeed protection

enabled

2 GND GND

LOW_BATTERY/ON_BATTE

/ON_BYPASS/UPS_FAULT/

Bypass backfeed protection

enabled

4 GND GND

Battery mode shut-

down/Any mode shut-down

(Remote Comms Shut-

down)/ Maintain mode

6 GND GND

Battery mode shut-

down/Any mode shut-down

(Remote Comms Shut-

down)/ Maintain mode

8 GND GND

9 +5V REPO power supply, 5Vdc 100mA

10 REPO Coil -NC

11 REPO Coil -NO

12 GND REPO ground

Default: LOW_BATTER, can be set-up via the

LCD settings page. Change main backfeed via

Paramset. When there is an alarm active on the

system, Pin 1 and Pin 2 are shorted together

Default: UPS_FAULT, can be set-up via the LCD

settings page. Change bypass backfeed via

Paramset. When there is an alarm active on the

system, Pin 3 and Pin 4 are shorted together

Default: Maintain mode, can be set-up via the

LCD settings page. When Pin 5 and Pin 6 are

shorted together, the function is valid

Default: Maintain mode, can be set-up via the

LCD settings page. When Pin 7 and Pin 8 are

shorted together, the function is valid

NC, ECO activated when there is an open circuit

between Pin 9 and Pin 10

REPO triggered when there is a short circuit

between Pin 11 and Pin 12

EXS

*: I/O dry contact port rating: 125 Vdc, 0.5 A; 30 Vdc, 1 A.

The terminals corresponding to Pin 11 and Pin 12 are reserved for configuring the REPO function. The REPO device

also requires a shielded cable for connecting the Normally Open remote REPO switch between the two terminals. If

not required, you should disconnect Pin 9 and Pin 10. Pin 9 and Pin 10 have been shorted together before delivery.

Note

32 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 34

EXS

Activating the UPS EPO will deactivate the rectifier, inverter and static bypass, but does not disconnect the UPS from the

mains input. If you wish to disconnect the UPS completely, it is also necessary to open the input MCB installed upstream of

the UPS when activating the EPO.

In the event of an emergency, close the REPO switch (supplied and installed by the user) in order to shut down the

rectifier and inverter, and switch the UPS off. Under normal conditions, the REPO switch cannot be used to isolate

the UPS from the mains input power. If an electronically controlled circuit breaker function is installed at the UPS

input, the REPO switch can be used to trip this breaker, thus cutting off the UPS mains input power. The position of

the REPO switch is shown in Figure 3-6, and the REPO cable connection is shown in Figure 3-8.

Figure 3-8 Connecting the REPO cable

The cable connection procedures are as follows:

1. R

elease the REPO port connection terminals '11' and '1

rip the insulation from the ends of the two copper core cables and insert them in the REPO port co

2.St

terminals '

11' and '12', and press the terminals down in order to secure the cables. The REPO cable connection

2'.

nnection

procedure is complete. Ensure that the REPO cable is connected securely in order to ensure that the REPO is not

activated inadvertently as the result of poor contacts.

In the case of parallel UPS systems, when connecting the REPO cable, users should connect terminal '11' of

REPO po

rt in parallel to one terminal of each electronic switch, and terminal '12' of the REPO port in parallel to the

the

other terminal of each electronic switch.

When the REPO switch at the user end is closed, the UPS will generate an alarm and cut off the output immediately,

and the UPS will not return to the normal operating state automatically. At this point, it is necessary to change the

REPO switch state, and switch the UPS on manually.

Note

1. We recommend using 0.82mm2 - 0.33mm2 copper core cable ( 18AWG - 33AWG signal cable).

2. If the REPO has been configured to trip an electronically controlled circuit breaker switch, after the REPO has been

activated it will be necessary to re-arm the switch before restarting the UPS.

RS232 Communication Port

To connect the serial port communication cables, proceed as follows:

Insert one end of the DB) serial port communication cable into the DB9 serial port (see port 3 in Figure 3-6) on the

rear panel of the UPS, and connect the other end to the DB9 port on the computer.

The pin functions of the DB9 port are listed below:

Pin No. Function

2 Send data

3 Receive data

5 Common terminal

USB Communication Port

The position of the USB port is shown in Figure 3-6.

To connect the UPS communication cables, proceed as follows:

Insert one end of the USB communication cable into the USB port on the UPS, and connect the other end to the USB

port on the computer.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 33

Page 35

After connecting the cable, it is necessary to install the USB drive program on the installation disk.

Parallel/LBS Communication Port

The position of this port is shown in Figure 3-6.

Intellislot Port

EXS

The position of this port is shown in Figure 3-6. The Intellislot port is used for installing optional cards, includ

the UNITY card, etc. The Intellislot port can be used together with other ports.

Multifunction port

The multifunction port uses the standard RJ45 port, which supports the Modbus/Jbus protocol and can be used to

connect the VERTIV temperature/temperature & humidity sensor. The user can enable Modbus/Jbus protocol

function or sensor function via the 'Settings' on the LCD.

Signal Cable Connection Steps

Note

Route the power and signal cables respectively. The signal cable shielding sheath must be earthed securely.

Rear cable access mode is available. See Figure 3-10 for a detailed description of the wiring method.

ing

Figure 3-10 Signal cables wiring route (rear cable access)

34 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 36

EXS

Chapter 4 Operator Control and Display Panel

This chapter introduces the functions and use of the components on the UPS operator and display panel, and

provides LCD display information, including the LCD screen types, detailed menu messages, prompt windows

message and UPS alarm list.

4.1 Introduction

The operator and display panel is located on the front panel of the UPS. The operator and display panel allows the

user operate and monitor the UPS, and view the UPS parameters, Ups and battery status information and any alarm

messages.

As shown in Figure 4-1, the operator and display panel includes an LCD screen, menu keys, and LED indicators (run

indicator and alarm indicator).

1. Menu keys 2. LCD 3. Run indicator

4. Alarm indicator 5. Power button

Figure 4-1 Operation and display panel

Note

The device includes a gravity sensor function, so that the LCD display direction will adapt to the device layout mode.

LED Indicators

he LED indicators consist of the run indicator and alarm indicator. Table 4-1 provides a description of these

indicators.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 35

Page 37

Table 4-1 Description of LED indicators

Indicator Colour State Meaning

On UPS output present

Run indicator Green

Yellow On Alarm active

Alarm indicator

Red On Fault present

/ Off No alarms, no faults

Blinking Inverter is starting

Off UPS output not present, inverter is starting

Audible Alarm (Buzzer)

UPS operation is accompanied with the following two different kinds of audible alarms, as described in Table 4-2.

Table 4-2 Description of audible alarm

Sound Meaning

Continuous beep

One beep every 0.5 seconds

One beep every second

One beep every 3.3 seconds This sound is generated in the event of a general UPS alarm condition

This sound is generated in the event of a UPS fault condition, such as a fuse or hardware

failure

This sound is generated in the event of a critical UPS alarm condition, such as an

Inverter overload

This sound is generated in the event of a critical UPS alarm condition, such as low

battery voltage

EXS

LCD and Function Keys

The operator and display panel includes five function keys, the respective functions are described in Table 4-3.

Table 4-3 Description of control buttons

Function key Silkscreen Description

Confirm Used to confirm or enter

Up Used to scroll up, scroll left or increase value, etc.

Down Used to scroll down, scroll right or reduce value, etc.

Exit Used to go back, exit, cancel or forbid operation

Power Used to switch on, switch off or transfer to Bypass mode

36 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 38

EXS

Figure 4-2 LCD screen

The LCD includes a user-friendly interface and a 320 × 240 dot matrix image display. Thanks to the user-friendly,

menu-oriented LCD it is possible to browse easily through the UPS input, output, load and battery parameters,

obtain information about the current UPS status and alarm messages, as well as performing functional setting and

control operations. The LCD also stores historical alarm records that can be retrieved for reference and diagnosis.

Initial Start-up Guide

When the UPS is the initial start-up phase, the interface shown in Figure 4-3 will appear to guide the user through

the basic UPS parameter setting procedure.

Figure 4-3 Initial Start-up Guide (1)

Welcome page

Click Next to start the guide procedure.

Language, date and time page

On this page, you can set-up the language, date and time as required.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 37

Page 39

Figure 4-4 Initial Start-up Guide (2)

Battery parameter page

On this page, you can set-up the battery cell number and total Ah.

The available settings are 24, 32 and 40. See the right hand diagram in Figure 4-5.

EXS

Figure 4-5 Initial Start-up Guide (3)

If there is an external battery module, the 'Local battery total Ah' will not appear, see Figure 4-6.

Figure 4-6 Initial Start-up Guide (3)

Output page

As shown in Figure 4-7, you can set-up the output voltage, output frequency, and output phase.

The 'Output phase No.' may be set to 'single' or '3 phases'. See the right hand diagram in Figure 4-7.

38 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 40

EXS

Figure 4-7 Initial Start-up Guide (4)

Note

In the case of the output page, the REPO terminal (forcible output shut-down) must be unplugged when carrying out the

settings, otherwise the interface shown in Figure 4-8 will appear.

Figure 4-8 Prompt for removing REPO terminal

End page

The interface shown in Figure 4-9 will appear. This means that the function keys and LCD are invalid; the user

cannot continue with the operation. Please switch the UPS off based on the prompt shown in Figure 4-10, confirm

that the actual wiring method applied to the output terminal is consistent with the method selected during the set-

up procedure, and then switch the UPS on again.

After start-up the user will be able top operate the UPS normally.

Figure 4-9 Initial Start-up Guide (5)

User Manual 10H52260UM60 - Rev. 1 - 10/2017 39

Page 41

4.2 LCD Menu Structure

EXS

Figure 4-10 LCD menu structure

4.3 LCD Screen Types

Start Screen

When the UPS is started up it performs a system self-test, during which the Start Screen is displayed for

approximately 10 seconds, as shown in Figure 4-11.

Flow Screen

Once the UPS self-test is complete, the flow screen shown in Figure 4-12 will appear.

The flow screen provides a total status overview of the UPS, including the input, bypass, rectifier, battery, inverter

and output, etc. Operating modes are displayed in colour, while invalid are displayed in grey.

Figure 4-11 Start screen

40 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 42

EXS

Figure 4-12 Flow screen

Press the

key on the flow page to access the primary screen.

Main Menu Screen

The main menu screen consists of six icons: Status, Settings, Control, Log, About, Maintain. As shown in Figure 4-13.

Figure 4-13 Main menu screen

Press the key on the main menu screen to return to the flow screen. Press the or key to move the

cursor and select the required sub-menu, then press the key to confirm it.

Sub-menu Screen

The sub-menu screen contains the UPS parameters and item settings.

After accessing the sub-menu screen, if there is a tab control, just move the cursor to the tab. At this point, you can

press the or key

to switch the tab. Press the

key to move the cursor to a specific item.

After accessing the sub-menu screen, if there is no tab control, the cursor will stop on a certain Item.

Press the

key to return to the previous screen.

For more details about the sub-menu screen, see following pages.

Status page

The Status page contains information about the Input, Bypass, Battery, Output and Load.

See below:

User Manual 10H52260UM60 - Rev. 1 - 10/2017 41

Page 43

EXS

Settings page

The Set

tings page can be used to access the Output, Battery, Parallel, Monitor, System, and Outlet settings. For

details about the setting up the parameters, refer to Appendix 1 .

See below:

42 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 44

EXS

User Manual 10H52260UM60 - Rev. 1 - 10/2017 43

Page 45

Control page

The Control page may be used to access the Turn ON/OFF/to BYPASS, Manual battery test, etc. functions. See

below:

Log page

The Log page can be used to access a list of current and historical UPS events. See below:

EXS

About page

The About page contains information about the Product, Network, and Efficiency. See below:

44 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 46

EXS

Maintain page

Note

The Maintain page is password protected and reserved for use by VERTIV service engineers only.

Default Screen

During the UPS operation, if there is no alarms for two minutes, the display will revert to the default as shown in

Figure 4-14. While the Default screen is displayed, if there are no alarm or fault conditions active, the Flow screen

shown in Figure 4-12 will be displayed if the user presses any key.

Figure 4-14 Default screen

User Manual 10H52260UM60 - Rev. 1 - 10/2017 45

Page 47

4.4 Prompt Window

A prompt window is displayed while the system is in operation to alert you to certain conditions and/or request you

to confirm a command or other operation. Table 4-4 lists the prompts and the associated meanings.

Table 4-4 Prompts and meanings

Prompt Meaning

System setting is different, please check When the parallel parameters are different, this prompt will appear

Cannot set this on-line, please shut down

output

Incorrect password, please input again This prompt will appear when the user enters an incorrect Settings password

Operation failed, condition is not met

Password changed OK This prompt will appear when the user has changed the Settings password successfully

Fail to change password, please try again

The time cannot be earlier than system time

Turn on failed, condition is not met

Cannot set this on line, please unplug REPO

Please disconnect power, check output: 1

phase, 3 phase, then power UPS on

If the user attempts to change certain important settings while the output is active

(output voltage, output frequency, output phase No.), this prompt will appear

This prompt will appear when the user attempts to execute a certain operation, but the

necessary condition is not met

This prompt will appear when the user attempts to change the Settings password but

has failed to the same new password twice

This prompt will appear when the user sets the 'Turn on delay' or 'Turn off delay’ value

to a time earlier than the current system time

This prompt will appear when the user presses the power button (or executes the 'Turn

on/Turn off/to Bypass' command on the 'Control' page).

This prompt will appear if the user attempts to change output phase No. while the

output is active

This prompt will appear when the output phase is changed. To ensure safety, the

system requests the user to switch the UPS off and check the cable connections, and

then switch the UPS on again

EXS

4.5 UPS Alarm Message List

Table 4-5 lists all the UPS alarm messages based on the 'Current' and 'History' menus.

Table 4-5 UPS alarm message list

Alarm message Description

Communication fail

Rectifier fault The rectifier is faulty and is not running

DC/DC fault

DC bus abnormal The inverter is off when DC bus voltage is faulty. The load will transfer to bypass, if the bypass is available

Charger fault The battery charger output voltage is abnormal, and the charger is off

Aux. power fault The auxiliary power output voltage exceeds the normal range

Input backfeed

Inverter fault

Output short circuit Check for short circuits between the output cables

Bypass backfeed Battery mode. The bypass relay is shorted or the SCR is damaged

Output off, voltage is

not zero

Inverter relay shorted The inverter relay is short circuited

Parallel No. abnormal

Parallel comm fault

Parallel cable

connection abnormal

Internal communication is abnormal, please check whether the communication cables are connected correctly

or not

The discharger is faulty, because the bus voltage exceeds the setting range when discharger starts or soft

starts

Battery mode. The mains relay is shorted and the difference between the mains and battery voltage is less

than the setting range

The inverter is off when the inverter output voltage and current exceed the setting range. If the bypass is

available, the UPS will transfer to bypass mode, otherwise the system will switch off

The Output is switched off, but the system detects the presence of a voltage at the output terminals

The on-line parallel number is inconsistent with the value in the settings. Please check that the parallel

number on the 'Settings' page is the same as the actual on-line number, and that the parallel cables are

normal

The local UPS and its on-line frequency configuration is different or there is a conflict with the parallel

address. Please check that the parallel system parameter setting is the same as the local parameter setting

The system has detected that the parallel cables are not secure

46 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 48

EXS

Alarm message Description

Input neutral lost

Input ground lost Check whether the PE line is connected securely, and that the alarm can be cleared on line

Input phase reversed

Input abnormal

Rectifier overload

Battery reversed

Battery low pre-

warning

Battery voltage

abnormal

No battery Check the battery and battery cable connections

Battery series not

qualified

Battery aged The battery capacity is less than 25% of the initial value. Battery replacement is recommended

Battery test fail

Battery overtemp

Battery cabinet not

connected

Fan fault At least one fan is faulty. Check whether the fan is blocked or the cables have been disconnected

System overtemp

Inverter overload

Bypass phase

reversed

Bypass overcurrent

Parallel bypass cable

connection abnormal

Bypass abnormal

Bypass abnormal in

ECO mode

Output LPE short

The AC input mains N line has not been detected. Please check whether the input N line has been interrupted

or disconnected

The mains AC input phase is reversed. Normally, phase B lags phase A by 120 degrees, and phase C lags phase

B by 120 degrees.

Check that the UPS mains input phase sequence is correct. If not, correct it

The rectifier and charger have switched off because the mains voltage and frequency values exceed the

normal operating range. Check whether the rectifier input phase voltage and frequency exceed the normal

range or the mains power has been switched off

The output power exceeds the rectifier overload point. Check that the input voltage meets the output load

requirement, a mains input range 176V - 100V corresponds to a load range of 100% - 50%, with linear derating

The battery positive and negative terminals have been inverted. Please reconnect the battery and check the

battery cable connections

This alarm is generated when the battery reaches the EOD (End Of Discharge voltage). The battery will

continue to provide full load discharge capacity for another two minutes after this warning appears. The user

can set this value ranging from 2min～30min, (2 min by default). Please shut down the load as quickly as

possible

When the battery is connected, the system checks whether the battery voltage exceeds the normal setting

range. Check whether the battery terminal voltage exceeds the normal setting range

The actual number of connected battery cells differs from the setting. Modify either the number of batteries

or the setting so that these two values are consistent

The battery low voltage is detected during the manual or periodic battery self-test. Battery replacement is

recommended

The battery ambient temperature is too high. Check whether the battery ambient temperature exceeds the

setting value of 40 - 60Ԩ (default: 50Ԩ)

The battery cabinet is not connected to the system

The internal heat sink temperature is too high, and the inverter has been switched off. This alarm may only be

cancelled by reducing the heat sink temperature of each module to within the setting range. The system will

restart automatically once the fault has been resolved.

In the event of overheating, please check:

1. If the ambient temperature is too high

2. If the ventilation holes are blocked by dust

3. That the fans are working correctly

The inverter load demand is exceeds the rated value, the overload delay time has expired, and the inverter has

shut down. If the bypass is available, the UPS will transfer to bypass mode, otherwise the output to the load will

be interrupted Check that the current inverter load demand, if it is overloaded, simply reduce the load demand

and the system will revert to inverter mode five minutes after the alarm condition has been cleared

The bypass voltage phase sequence is reversed. Normally, phase B lags phase A by 120 degrees, and phase C

lags phase B by 120 degrees.

Check that the UPS bypass input phase sequence is correct. If not, correct it

The bypass current exceeds the rated value. The overload delay time has expired and the inverter has shut

down

The bypass phase number is different from the output phase number indicated on the 'Monitor’ page. Please

check that the bypass cable connection is the same as the configured phase number

This may be caused by the bypass voltage and frequency being outside the acceptable range, the bypass

being switched off or by the bypass cables being connected incorrectly

1. Check that the bypass voltage and frequency are within the setting range.

2. Check the bypass cable connections

ECO mode is available, and the bypass voltage and frequency are outside the setting range. Check that the

bypass input voltage and frequency are within the setting range.

There is a short circuit between the output and the enclosure Check for short circuits between the output

cables and the enclosure

User Manual 10H52260UM60 - Rev. 1 - 10/2017 47

Page 49

Alarm message Description

Output pending Remote shut-down has been enabled, and the system will be switched off

Output disabled

Version incompatible The monitoring board and DSP board versions are incompatible

Electrical leakage

alarm

On maintenance

bypass

Battery mode The UPS is in battery mode, and the inverter starts running

Bypass mode The UPS is in bypass mode

System overload

Loss of redundancy

Load sharing

abnormal

System parallel

settings async.

Local parallel settings

async.

LBS abnormal

REPO The UPS has been shut down because the Normally Closed REPO terminal contact has been opened

Bypass phase

reversed

System battery low

pre-warning

Battery test started The periodic battery self-test or manual self-test is in progress

Battery test stopped The periodic battery self-test or manual self-test is complete

EOD turn off

Guaranteed shut-

down

Shut-down due to

overtemp

Remote shut-down Dry contact activated causes shut-down irrespective of operating mode

Remote power-on UPS switched on remotely

Remote shut-off UPS switched off remotely

Load off due to shut-

down on battery

Output off due to

bypass abnormal

Battery to utility

transition

Manual power-on Set power-on via LCD panel

Manual shut-down Set shut-down via LCD panel

Operating on inverter The UPS output is supplied by the Inverter

Battery series set to

(32-40)

Restore factory

defaults

Output phase No. set

to 1

The system is in the standby state, and the shut-down dry contact has been enabled Check whether the shut-

down dry contact has been enabled or not

Short circuit between bus and enclosure or between battery and enclosure. Check for short circuits between

the bus or battery cables and the enclosure

The maintenance bypass state dry contact has been activated

The parallel system load demand exceeds the max. load capacity of the parallel sets. Check the parallel

system load demand, and if the system is overloaded, simply reduce the load

After parallel redundancy has been enabled, the system load demand exceeds the rated load capacity (the

load capacity is equivalent to the total capacity of the on-line sets, minus one)

Load sharing is abnormal in the parallel system

Check that parallel setting parameters of each unit are consistent

Check that the Settings pages for the local unit and the other units are consistent

Check that the LBS cables are normal, the system is in stand-by mode, or that the system is in bypass mode

and it is not possible to trace the bypass

In parallel connection configuration, the bypass phase sequence is not consistent. Check the parallel bypass

cable connections

In a parallel system, there is a battery voltage low warning for all the devices supplied by the battery inverter

The inverter has switched off because EOD has been reached. Check the mains power-off state and restore

the mains in time

In forced EOD mode, then system shuts down once the battery is fully discharged

During the UPS operation, the system checks whether the heat sink temperature exceeds the setting range.

In the event of overheating, please check:

1. If the ambient temperature is too high

2. If the ventilation holes are blocked by dust

3. That the fans are working correctly

Shut-down in battery mode

The bypass is abnormal, and has switched from the working state to the standby state. Check that the bypass

input is normal

The UPS is powered by the mains instead of the battery

The number of battery cells has been modified

With the UPS in standby mode, select the 'Restore Factory Defaults' function on the Maintain page

The output phase has been changed from 3-phase to 1-phase

EXS

48 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 50

EXS

Alarm message Description

Output phase No. set

to 3

UPS out of service The UPS is out of service

Switch on

programmable output

Switch off

programmable output

System parallel

settings start sync

Local settings sync

System settings sync

Load off due to output

short

Output off due to

overload & bypass

abnormal

Parallel No. abnormal

Bypass disabled

In intelligent sleep

mode

Battery cabinet

connection abnormal

Battery cabinet not

connected

Battery EOD Battery end of discharge voltage reached

Faults cleared Press the 'Clear faults' button on the 'Control’ page, the system then records this event

Manual shut off After the user shuts down the UPS output, the system will record this event

System warning

System fault This alarm occurs when the model identification is incorrect. Solution: Contact service manager

The output phase has been changed from 1-phase to 3-phase

The programmable output status has been changed from Switch Off to Switch On

The programmable output status has been changed from Switch On to Switch Off

Set the 'Sync parallel parameters' command manually to activate the event

The local parameters have been synchronized successfully

All the parameters have been synchronized successfully

There is a short circuit on the inverter or bypass output Carry out the appropriate checks

The output has been switched off due to an overload and the bypass supply is abnormal. Carry out the

appropriate checks

The parallel on-line number and the configured value are inconsistent Please check that the parallel number

on the 'Settings' page is the same as the actual on-line number, and that the parallel cables are normal

If Settings->Output->Frequency is set to 'Auto, BypDisa; 50Hz, BypDisa; 60Hz, BypDisa', the LCD will generate

the BypDisa alarm

When intelligent sleep mode is enabled, the system may perform N sets of inverter start-up. When the system

meets the sleep mode requirements (Condition for entering sleep mode: The UPS must be connected to a

common, large battery string (if there is no large battery string, entering sleep mode will result in the charger

failing to recharge the battery), sleep mode must be enabled on the host, there must be no faults or alarms

active on the inverter or rectifier, the battery must not require recharging, a period of at least 1 hour must

have elapsed since last exiting sleep mode, the unit is not the master unit and, with the exception of the

module in sleep mode, the local unit ID number has not received a start-up command within the last 5

minutes). When the N minus 2 unit rated load is larger than the existing system rated load capacity, the unit

with the largest ID number starts to enter sleep mode (inverter off), at this point, N minus 1 units are

operating in inverter mode. When the N minus 3 units are larger than the current system rated load capacity,

the unit with the largest ID number remains in sleep mode

The system detects that there are more than six battery cabinets connected and indicates that the battery

cabinet connection is abnormal

The battery cabinet group number is specified, but the communication cables are not connected

In the case of parallel systems, this alarm is generated when the UPS auto-adapting output frequency is

inconsistent. Solution: Switch on again

If the alarm is generated as the result of a software value set-up by an authorised VERTIV engineer, and you wish to

modify the setting, please get in touch with your local VERTIV customer service centre.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 49

Page 51

Chapter 5 Operating Procedures

This section introduces the operating precautions and describes the UPS operating procedures in detail.

5.1 Brief Introduction

Precautions

Important

The user may only carry out the operations described in this section once the authorised service engineer has switched the

UPS on for the first time and completed the commissioning tests

Warning: hazardous mains and/or battery voltage

1. No user serviceable parts are located behind the protective covers that can only be removed by using tools. Only qualified

service personnel are authorized to remove such covers.

2. Hazardous voltages may be present on the UPS AC input and output terminals at any time. If the cabinet is equipped with an

EMC filter, hazardous voltages may be present on the filter.

1. For information about the control keys and LCD related to all the operating steps, refer to Chapter 4 .

EXS

ng operation, the buzzer alarm may be activated at any time. Press the key for 3s to silence the audible

Duri

alarm.

. When the UPS is equipped with traditional lead-acid batteries, the system provides the optional boost charge

function.

If lead-acid batteries are used, when the mains returns after an extended mains failure, the battery

charging voltage will be higher than the normal charging voltage, this is normal, and the charging voltage will return

to its normal value after a few hours.

Power Switch

Open the front door of the UPS cabinet to access the power switches, as listed below, (see Figure 5-1):

Q1: Rectifier input switch - connects the UPS to the main power supply.

Q2: Bypass input switch - connects the UPS to the bypass power supply.

Q3: Maintenance bypass switch (lockable) - supplies power to the load when UPS is being serviced.

Note

If the UPS system consists of more than 2 UPS modules in parallel, do not use the internal maintenance bypass switch

Q5:

Output switch - connects the UPS output to the load.

50 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 52

EXS

5.2 UPS Start-up Procedures

Check Before Start-Up

1. Check and confirm that the UPS and POD power distribution mode (if configured) is correct, that the power and

signal cables ar

Check that the batteries ha

e and negative battery poles are correct.

positiv

3. Measur

4. The UPS a

alr

eady connected to the output terminals, make sure that it is safe to apply power to it.

Start-up Interface

The first time the system is started up, mains input mode only may be used, and the LCD screen will display the

start-up interface, see Figure 5-2.

e connected correctly, and there are no short circuits.

ve been installed properly, the cable have been connected correctly, and that th

e the mains voltage and frequency, and verify that they are correct.

nd POD (if configured) output terminals are energised when the UPS is switch

Figure 5-1 UPS power switch

ed on. If the load is

User Manual 10H52260UM60 - Rev. 1 - 10/2017 51

Page 53

Figure 5-2 Start-up interface

Start-up Procedures In Normal Mode

Warning

1. These procedures result in mains voltage being applied to the UPS output terminals.

2. If any loads are connected to the UPS output terminals, check with the user that it is safe to apply power. If the load is n

ready to receive power, ple

ase disconnect the downstream load switch, and apply a warning label at the load connection point.

EXS

Use the f

ollowing procedures to switch the UPS on when it is in the fully switched off state.

1. Ensure that the internal maintenance bypass switch Q3 is off, and that the input cables and PE terminals are

ted securely.

connec

2. Close the UPS bypass input switch Q2, rectifier input switch Q1, output switch Q5 and all external output isolating

witches (if any) in that order. The rectifier runs in normal state for about 30 seconds, after which the rectifier start-

up phase is complete.

3.Finish setting up the single UPS parameters and check them

Access the main menu screen, pr

ess the

or key to select 'Settings', and press the key to access

the interface shown in Figure 5-3.

Figure 5-3 Main menu screen

b) Press the or key to select and set-up corresponding parameters (taking 'Output' as an example). As

shown in Figure 5-4.

52 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 54

EXS

Figure 5-4 Output interface

4. After setting up the corresponding parameters, press the power button for two seconds so that the dialogue box

n in Figure 5-5 appears on the LCD screen.

show

Figure 5-5 Switching the UPS on

After selecting 'YES', the run indicator (green) blinks, the inverter starts, and the run indicator switches on.

5.Measure the inverter output voltage and verify whether it is within normal limit

he battery is not connected, the alarm indicator will be coloured yellow. If the battery is connected, the al

6.If t

indica

tor will be extinguished.

Start-up Procedures In Battery Mode (Battery Cold Start)

1. In the case of UPS with internal batteries, simply press the power button on the UPS front panel for two seconds; in the case of UPS with external batteries, close the circuit breaker first, and then press the power button on the

UPS front panel for two seconds, at this point the LCD disp

lays the start-up screen. The alarm indicator will be

coloured yellow and the buzzer will beep continuously after the rectifier completes the start-up phase.

2. Press the power button for two seconds so that the dialogue box shown in Figure 5-6 appears on the LCD screen.

arm

User Manual 10H52260UM60 - Rev. 1 - 10/2017 53

Page 55

Figure 5-6 Switching the UPS on

EXS

After selecting 'YES', the inverter starts, and the run indicator (green) is illuminated.

5.3 Procedures for Transferring Between Operating Modes

Note

The Inverter operating modes include Normal mode and Battery mode.

Transfer from Normal Mode to Battery Mode

When the mains supply is interrupted, the UPS will transfer to Battery mode. If you wish to transfer the UPS from

Battery mode to Normal mode, wait few seconds for the mains input to recover. After about ten seconds, the

rectifier will restart automatically, and the inverter will restore the power.

Transfer from Normal Mode to Bypass Mode

In stand-by mode, press and hold the power button. If the rectifier and inverter are normal, the interface shown in

Figure 5-7 will appear, select 'YES' to switch the UPS on.

Figure 5-7 Switching the UPS on

In Inverter mode, press and hold the power button. If the bypass is normal, the interface shown in Figure 5-8 will

appear. Select 'To Bypass' and click OK to transfer the UPS to Bypass mode; select 'Turn off UPS' and click OK to

turn switch the UPS off.

54 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 56

EXS

Figure 5-8 Bypass normal interface

In Inverter mode, press and hold the power button. If the bypass is abnormal, then the interface shown in Figure 5-9

will appear, select 'YES' to shut down the UPS output.

Figure 5-9 Bypass abnormal interface

Note

In Bypass mode, the load is directly fed by the mains power instead of the pure AC power from the inverter.

For detailed information about Normal mode, Bypass mode, and Battery and Maintenance Bypass mode, please refer

to 1.4 .

Transfer From Bypass Mode To Inverter Mode

In Bypass mode, press and hold the power button.

If ECO mode is not enabled, the interface shown in Figure 5-10 will appear.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 55

Page 57

EXS

Figure 5-10 ECO mode not enabled

Select 'Turn on UPS' and click OK to transfer to Inverter mode, see Figure 5-11.

Select 'Turn off UPS' and click OK to shut down the UPS output.

Figure 5-11 Bypass to inverter mode

If ECO mode is enabled, the interface shown in Figure 5-12 will appear. Select 'YES' to shut down the UPS output.

Figure 5-12 ECO enabled interface

56 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 58

EXS

Transfer From Normal Mode To Maintenance Bypass Mode

When the UPS is running in Normal mode, you can use this procedure to transfer the load from inverter output to

maintenance bypass.

Caution

Before performing this procedure, you should check the LCD information first, and make sure the bypass is normal and

synchronized with the inverter. Failure to do so may result in a brief interruption in the power supply to the load.

1. Remove the maintenance bypass switch baffle retaining screws, rotate the baffle upwards until it is locked in

position, and

then fasten the retaining screws. As shown in Figure 5-13.

Figure 5-13 Moving the baffle upwards

At this point, the system Interlock function has been activated and the UPS will transfer to internal bypass mode;

you should confirm that the UPS has been transferred to internal bypass mode.

2. After confirming, close the maintenance bypass switch Q3.

3.D

isconnect the output switch Q5

Caution

When the UPS is in maintenance bypass mode, the load is not protected against abnormalities in the mains power supply.

4. Unplugging the REPO terminal deactivates the rectifier, inverter, static switch and battery, but does not affect the

nance bypass power supply to the load.

mainte

Note

In maintenance mode, the load is fed directly by the mains power instead, of the pure AC power from the inverter.

5. Disconnect the rectifier input switch Q1 and bypass input switch Q2. At this point, all the internal power supplies

e deactivated and the LCD screen is switched off.

6. If the UPS is equipped with internal batteries, make sure that that they have been isolated from the UPS before

carrying out maintenance work on it. Refer to 6.10 for details.

Transfer From Maintenance Bypass Mode To Normal Mode

Following UPS maintenance operations, the following procedures may be used to transfer the load from the

maintenance bypass to the inverter.

1. If the UPS is equipped with internal batteries, simply connect the UPS and internal batteries when you finish

vicing the UPS. Refer to 6.10 for details.

ser

2. Close the output switch Q5.

3. Close the bypass input switch Q2

ollowing the LCD start-up, ensure that the system is operating

4. F

Warning

User Manual 10H52260UM60 - Rev. 1 - 10/2017 57

in Bypass mode.

Page 59

It is important to close the bypass switch (Q2) before opening the maintenance bypass switch; otherwise the power supply to

the load will be interrupted.

5. Set internal maintenance bypass switch Q3 to off. Return the Q3 baffle to its original position, then fasten the

taining screws.

6. Close the rectifier input switch Q1, wait for the rectifier to start-up.

7.Press t

he power button on the operator and display panel of the UP so that the UPS transfers to Inverter

t this point, the load has transferred to UPS normal mode.

5.4 UPS Shut-down Procedures

Procedures For Completely Powering Down the UPS

In order to shut the UPS down completely and disconnect the power supply to the load, proceed as follows: All

power switches, isolating switches and breakers are switched to off, and the UPS no longer supplies power to the

load.

Caution

The following procedures will interrupt the power supply to the load, switching it off.

EXS

mode.

1. Press the power button on the display panel, the UPS will transfer to Bypass mode.

2.Unplu

g the REPO terminal at rear of the UPS to deactivate the rectifier, inverter, static switch and battery.

3. If the UPS is equipped with an external battery, set the corresponding external battery switch to off.

et the rectifier input switch Q1 and bypass input switch Q5 to off. At this point, all the internal power supplies ar

4. S

ated and the LCD screen is switched off.

deactiv

Warning

1. Post a label on the AC input distribution line (generally at a distance from the UPS) to alert personnel that UPS

maintenance is in progress.

2. Wait 10 minutes for the internal DC bus capacitors to discharge. Then the UPS is completely shut down.

Warning: hazardous battery vol

Hazardous voltages are still present on the battery terminals, even after the UPS has been shut down.

tage

Procedures Shutting Down the UPS Completely While Maintaining Power To Load

The following procedures may be used to shut the UPS down completely are applicable for completely, while

maintaining the power supply to the load. Refer to the procedures in 5.3.4 .

5.5 REPO

The REPO port, located at rear of the UPS, is designed to switch off the UPS in the event of an emergency (such as

fire, flood). After unplugging the REPO terminal, the system will switch off the rectifier and inverter, and interrupt

the power supply to the load immediately (inverter and bypass output included), while the battery will stop charging

or discharging.

After EPO, if the mains input is present, the UPS control circuit will remain active; however, the output is interrupted.

To completely remove all mains power from the UPS, first disconnect the UPS external mains switches, and then

disconnect the battery terminals.

58 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 60

EXS

5.6 Automatic Restart

In the event of a mains power failure, the UPS draws power from the battery in order to supply the load until the

batteries are discharged, at which point the UPS will shut down.

The UPS will restart automatically and resume supplying power to the load:



Once the mains power supply is restored.



If the UPS Auto Restart function is enabled.



After the Auto Restart delay has expired (default: 10s). During the Auto Restart delay, the UPS will charge the

ttery in order to provide a safety margin for equipment shut-down if input power fails again.

If the Auto Restart function is disabled, you can restart the UPS manually by pressing the power button.

5.7 Language Selection

The LCD menus are available in two languages: Chinese, English.

Language selection procedure:

Access the main menu screen and press the or

the key to confirm. See Figure 5-14.

key to switch the cursor to select 'Settings', then press

Figure 5-14 Main menu

2. Press the key to move the cursor to 'Monitor', see Figure 5-15.

Figure 5-15 Monitor interface

3. Press the key to highlight the language, see Figure 5-16.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 59

Page 61

Figure 5-16 Language selection

EXS

4. Press the or

key to select your required language, then press the key to confirm. At this point

the LCD information will be displayed in your selected language. See Figure 5-17.

Figure 5-17 Changing Language

5. Press the key several times to return to the main menu screen.

5.8 Changing the Current Date And Time

Procedures for changing the system date and time:

Access the main menu screen and press the

key to confirm. See Figure 5-18.

key to switch the cursor to select 'Settings', then press the

Figure 5-18 Main menu screen

2. Press the key to move the cursor to 'Monitor', see Figure 5-19.

60 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 62

EXS

Figure 5-19 Monitor interface

3. Press the key, followed by the or key to highlight the date and time, see Figure 5-20.

4. Press the key, move the cursor and press the

See Figure 5-21.

5. Press the key to confirm, and then press the key several times to return to the main menu screen.

5.9 Setting the Password

1. After switching the UPS on, access the main menu screen and press the or key to move the cursor to

select 'Settings'. See Figure 5-22.

Figure 5-20 Selecting date and time

Figure 5-21 Changing date and time

key to change the date and time as required.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 61

Page 63

Figure 5-22 Main menu

2. Press the key, the interface shown in Figure 5-23 will appear.

EXS

Figure 5-23 Entering the password

To change the password, proceed as follows:

1. Press the

key to move the cursor to the 'Monitor’ page, see Figure 5-24.

Figure 5-24 Monitor interface

2. Press the key, then press the key to select 'Change settings password', see Figure 5-25.

62 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 64

EXS

Figure 5-25 Changing the settings password

3. Press the key, the interface shown in Figure 5-26 will appear.

Figure 5-26 Settings password

4. Enter the current password and press the key to confirm; at this point requests the user to enter a new

password. See Figure 5-27.

Figure 5-27 Entering the new password

5. After entering the new password, press the key to confirm; at this point the system requests the user to

confirm the new password by entering it again, see Figure 5-28.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 63

Page 65

EXS

Figure 5-28 Confirming the new password

6. After the confirming the new password, press the

key; at this point a system prompt appears indicating that

the password has been changed successfully, see Figure 5-29.

Figure 5-29 Password changed successfully

7. Press the

In order to access the UPS parameters it is necessary to enter the correct password (default:111111)

key several times to return to the main menu screen.

Note

64 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 66

EXS

Chapter 6 Battery

This section introduces the battery, providing information about safety, installation and maintenance, and the

battery protection function.

6.1 Introduction

The UPS battery string consists of a number of batteries connected in series, and provides rated DC input voltage

for the UPS inverter. The required battery backup time (i.e. The length of time the battery is able to supply the load

for following a mains failure) depends on the ampere-hour value of the battery. Under certain conditions, it may be

necessary to connect several battery strings in parallel.

For ease of installation, the battery is generally placed in the specially designed battery rack or a dedicated battery

room.

During the maintenance or repair, the battery must be disconnected from the UPS. This may be achieved by using a

suitably rated battery circuit breaker. This circuit breaker must be located as close as possible to the battery

connection terminals, while the length of the power and signal cables connected to the UPS must be kept to a

minimum.

When several battery strings are connected in parallel in order to increase the battery backup time, each string must

be fitted with its own disconnecting device, so that, when it is necessary to carry out maintenance work on an

individual battery string, the normal operation of the other strings is not affected.

6.2 Safety

Take special care when working with the batteries associated with this UPS. When all the blocks are connected, the

battery string voltage can reach 540Vdc. This is potentially lethal. Please follow the precautions for working with

high voltages.

Only qualified personnel may install and service the battery. To ensure safety, the external batteries must be

installed inside a lockable cabinet or in a purpose-designed, dedicated battery room, so that they are only

accessible to qualified service personnel.

Confirm that the battery switch has been set to off before carrying out battery maintenance operations.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 65

Page 67

EXS

Warning: hazardous battery voltage present behind covers

1. No user-serviceable parts are located behind the protective covers that can only be removed by using tools. Only qualified service

personnel are authorized to remove such covers.

2. Before working on the copper bars connected to the external battery, please ensure they are disconnected from all power supplies.

Proper connection mode Improper connection mode

Tighten the terminal bolt of the battery,

applying the specified torque

3. Observe the following safety precautions when working on the batteries:

a) The batteries must be firmly and securely connected. After the connection is completed, the screw connections between all the

terminals and the batteries shall be calibrated. The torque requirements indicated in the specifications or user manual provided by the

battery manufacturer must be respected. The connections between all the wiring terminals and the batteries shall be inspected and

tightened at least once a year. Failure to do so may result in fire!

b) Visually inspect the batteries before accepting and/or using them. If the packaging is damaged, the terminals are dirty, eroded or

rusty, or if the cases are cracked, deformed or leaky, replace the battery with a new one. Failure to do so may result in reduced battery

capacity, leakage of electrolyte or even fires.

Battery damaged during handling or shipping After a week of normal charge/discharge cycle testing

Applying too little or too much torque may result in poor connections. Under

certain conditions, the terminal may be subject to arcing or heat accumulation,

which can result in fire

c) Batteries are very heavy. Please use the proper procedures when moving and lifting batteries in order to prevent injury and avoid

damaging battery terminals. Severe damage to the battery may cause fire.

d) The battery connecting terminal must not be subject to any force, such as pulling twisting forces exerted by the cables, otherwise,

the internal battery connections may be damaged. Severe damage to the battery may cause fire.

e) The battery must be installed and stored in a clean, cool and dry environment. Do not install the battery in a sealed battery chamber

or a sealed room. The battery room ventilation shall at least meet the requirement of EN50272-2001. Otherwise, battery bulging, fire or

even human injury may be caused.

f) Batteries must be installed away from heat sources (e.g. Transformers) and kept away from sources of fire, in addition, they must not

be burnt or heated in a fire. Otherwise, battery leakage, bulging, fire or explosion may be caused.

g) Do not connect conductors directly between the positive and negative terminals of the battery. Remove the rings, watches,

necklaces, bracelets and other metal items before working on batteries, and always used insulated tools (e.g. wrenches). Otherwise,

battery burning, human death/injury or explosion may be caused.

h) Do not attempt to disassemble, modify or demolish batteries. Otherwise, battery short circuit, liquid leakage or even human injury

66 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 68

EXS

Warning: hazardous battery voltage present behind covers

may be caused.

i) Clean the battery enclosure with a damp cloth. To avoid any static or arcing, do not use dry cloths or dusters to clean the batteries.

Do not use the organic solvents (such as thinners, gasoline, volatile oil) to clean the batteries. Otherwise, the battery enclosure may be

cracked. In the worst case this may even result in fires.

j) The batteries contain diluted sulphuric acid. In normal use, the diluted sulphuric acid will be absorbed by the battery baffle and polar

plate. However, if the battery is damaged, it may leak acid. Therefore, personal protective equipment (e.g., protective glasses, rubber

gloves and apron) must be used when working with batteries. Failure to observe the above may result in blindness, if the sulphuric acid

comes into contact with the eyes, or burns, if it comes into contact with the skin.

k) batteries may be a affected by short circuits, electrolyte dry-up or positive pole erosion failure at the end of their service life.

Continued use it this state may result in thermal runaway, bulging or liquid leakage. Please replace the batteries before they reach this

state.

l) Before connecting or disconnecting the battery connection cables, please isolate them from the battery charger terminals.

m) Check whether the battery has been unexpectedly earthed. If so, remove the earth connection. Contact with any part of the earthed

battery may result in an electric shock.

6.3 UPS Battery

The UPS is normally equipped with valve-regulated batteries. The term 'valve-regulated' replaces the 'sealed type'

or 'maintenance free', which were used in the past.

Valve-regulated batteries are not completely sealed, therefore some gas will be expelled especially when they are

over-charged. The volume of expelled gas is less than that for water injection type batteries. However, when

designing the battery installation area, it important to take the possibility of temperature rise into account and

ensure there is sufficient space to ensure good ventilation.

Additionally, it is worth noting that valve-regulated batteries are not entirely maintenance free. In fact, they must be

kept clean, and inspected regularly to check if the connection is secure and the terminals are free from corrosion.

For details, please refer to 6.9 .

We recommend that you do not connect more than 4 strings of batteries in parallel. All batteries in the same system

must be of the same type, brand, capacity and age. Failure to observe this condition will result in regular over/under

charging of certain batteries within the string. This will eventually lead to premature failure, compromising the back-

up time of the affected string.

The battery must be stored in fully charged state. The battery will lose a certain proportion of its capacity due to

self-discharge during the shipping or storage. Charge the battery before use. During storage, ensure that the

ambient temperature remains within between -15°C and +45°C; the optimal temperature range is between 20°C and

25°C. To compensate for the self-discharge, recharge the battery once every 3 months during while it remains in

storage. This period may differ, depending on the specific batteries. For details, refer to the battery manufacturer’s

specifications.

It is important to ensure the battery is fully charged before carrying out the on site battery backup time test. This

test may take several days. Therefore, it should be conducted after the battery has been subject to uninterrupted

float charging for at least one week.

The battery performance will gradually increase after it has been running for several weeks or subject to two to

three charge and discharge cycles.

To avoid over/under-charging the battery, please set-up the battery management parameters according to the

equalizing/float charge voltage and temperature compensation factor specified in the manuals provided by the

battery manufacturer. Please charge the battery immediately after is has been discharged.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 67

Page 69

6.4 Precautions For Installation Design

Note

1. The precautions that must be applied when installing, using and servicing the batteries are described in the respective

battery manual provided by the battery manufacturer.

2. The safety precautions described in this section include important matters that must be taken into account when designing

the installation.

3. The design results may vary according to the local situation.

6.5 Battery Installation Environment and Number of Batteries

Installation Environment

Fresh air volume (EN50272-2001)

The battery operating environment must be well ventilated. During battery operation, the following fresh air

ventilation requirement must be satisfied:

Q=0.05 x n x I

Where:

Q = The fresh air ventilation volume per hour, the unit is m

x Crt x 10–3[m3/h]

gas

EXS

N = Number of cells

= The gas evolving current density under battery float charging or boost charge conditions, the unit is mA/Ah

gas

=1, under the float charging condition of 2.27V/cell

gas

=8, under the float charging condition of 2.35V/cell

gas

= 20hr battery rated capacity

Temperature

Table 6-1 Ambient temperature range

Typ e Temperature value Note

Recommended

optimal temperature

Short time allowable

temperature

-15

°C

- 25°C

- 45°C

The ambient temperature for the battery operation must not be too high or

too low.

If the average operating temperature of the battery rises from 25

the service life of the battery will be reduced by 50%. If the operating

temperature of the battery exceeds 40

be reduced exponentially each day

, the service life of the battery will

°C

to 35°C,

°C

The higher the temperature, the shorter the battery service life. At low temperatures, the charge/discharge

performance of the battery will be significantly reduced.

The battery must be installed in a cool and dry environment where the relative humidity is less than 90%, and must

be protected from heat sources and direct sunlight.

The ambient temperature, ventilation, space, float/boost charge voltage and ripple current will all affect the battery

temperature. Uneven temperature among the battery strings will cause uneven voltage distribution and thus

compromise performance. Therefore, it is very important to maintain a balanced temperature along the entire length

of the battery string, and to ensure that the temperature difference between batteries on different layers does not

exceed 3°C. Valve-regulated batteries are very sensitive to the temperature, therefore the working temperature

should be maintained between 15°C and 25°C. If the battery cabinet is installed near the UPS, the maximum design

ambient temperature shall be determined according to the battery rather than the UPS. This means that, if valve-

regulated batteries are used, the indoor ambient temperature shall be 15°C - 25°C rather than the operating

temperature range of the UPS modules. Provided the average temperature remains below 25°C, brief excursions in

excess of this value are permitted.

68 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 70

EXS

Number Of Batteries

The number of batteries, EOD voltage, and float charging voltage must be consistent with the voltage selection

(380V/400V/415V), as shown in Table 6-2.

Number of cells (standard) 192, 240

EOD voltage 1.60Vdc/Cell - 1.85Vdc/Cell, 1.62V/cell recommended

Float charging voltage 2.2Vdc/Cell - 2.3Vdc/Cell, 2.27V/cell recommended

6.6 Battery Protection

If internal batteries are selected, the UPS is equipped with an internal fused designed to protect the internal battery. If external batteries are selected, please select a circuit breaker with sufficient DC breaking capacity.

The external battery must be connected to the UPS via the circuit breaker. In the case of rack-mounted batteries (or batteries that are installed at a distance from the UPS cabinet), the circuit breaker must be installed as close to the battery as possible, and the length of the power and signal cables connected to the UPS must be kept to minimum.

To obtain the required backup time, the batteries may be connected in parallel. In this case, the circuit breaker must be installed downstream of the battery parallel connection point.

Table 6-2 Number of batteries

Parameter 380V/400V/415V

Note

Only trained personnel may operate and service the battery circuit breaker.

6.7 Battery Installation and Connections

Battery Installation

1. Before installation, check the batteries for damage, inspect and count the accessories, and carefully read this

manual and the user manual or installation instructions provided by the battery manufacturer.

2. There must be a vertical gap of at least 10 mm between the batteries in order to ensure the free circulation of the

ambient air between the batteries.

3. A certain amount of clearance shall be maintained between the top of the batteries and the next layer in order to

facilitate battery monitoring and service operations.

4. Install the batteries starting from the bottom layer and working upwards, in order to avoid creating a high centre

of gravity. The battery shall be properly installed and protected against vibration and/or impacts.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 69

Page 71

Battery Connections

1. All the battery cabinets or battery racks must be connected and properly grounded.

2. When multiple battery strings are used, they shall be connected first in series and then in parallel. Before

switching the UPS on and connecting it to the load, check that the total voltage of the batteries is as specified. The

negative and positive poles of the batteries must be connected to the negative and positive battery terminals of the

UPS, in accordance with the labels on the battery and UPS. If the battery connections are inverted it can cause fires

or explosions, and may result in battery and UPS damage or even human injury.

3. When the battery cable connection procedure is complete, install insulating shields on the terminals.

When connecting the cable between battery terminal and circuit breaker, the circuit breaker terminal must be

4. connected first.

5. The bending radius of the cable shall be larger than 10D, wherein D is the outer diameter of the cable.

6. When the battery cable is connected, it is prohibited to pull on the battery cable or the cable terminal.

7. Do not cross the battery cables when connecting them, and do not tie the battery cables together.

8. See 8.2.1 Internal Battery Kit for details about the battery connections.

6.8 Designing the Battery Room

Irrespective of the type of installation system that is adopted, it is important to pay particular attention to the

following items (refer to Figure 6-1):

EXS



Layout of cells

Irrespective of the type of installation system that is adopted, the batteries must be positioned so that no two parts

having a potential difference of greater than 150 V can come into contact with each other at any time. If this is

unavoidable, insulated terminal shields and insulated cables shall be used for the respective connections.



Workbench

The workbench (or p

latform) must be skid-proof and insulated, and at least 1m wide.

Wiring

All the wiring distances shall be kept to a minimum.

circuit breaker

The circuit breaker is normally installed in a wall-mounted box close to the battery.

Figure 6-1 Design of battery room

6.9 Battery Maintenance

For the battery maintenance and maintenance precautions, refer to IEEE-Std-1188-2005 and the relevant manuals

provided by the battery manufacturer.

Note

1. Check the battery connection screws at regular intervals. If any loose screws are found, re-tighten them immediately.

70 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 72

EXS

2. Make sure that all the safety devices are present, in good condition and that they function correctly, and make sure that the

battery management parameter settings are correct

3. Measure and log the air temperature in the battery room.

4. Check to the battery terminals for damage or signs of heating, and that the battery enclosure and terminal shields are

intact.

For details, refer to 9.2 .

6.10 Disconnecting or Connecting Internal Battery Terminals

Warning

1. If you need to service the UPS, please be sure to disconnect cable connections between the UPS and batteries. Failure to

observe this condition may result in electric shock or battery arc risk.

2. Batteries may only be service by qualified personnel and the appropriate protective equipment and clothing must be used

at all times.

When the UPS has been fully shut down, if it is equipped with internal batteries the internal battery terminals will

remain live because there is no switch between the UPS and its internal batteries.

Use the appropriate tools to open the front cover of the battery compartment, and then disconnect the connection

between the UPS and its internal batteries. Refer to Figure 8-1 and Figure 8-3 for details. Wear arc protective gloves

and arc protective clothing when disconnecting the cabinet battery terminals and internal battery terminals. To

disconnect the internal batteries in the standard UPS, simply open the connection terminals between W101 and

W107, W102 and W106, W103 and W108; to disconnect the internal batteries in the UPS with side cabinet, simply

open the connection terminals between W101 and W107, W102 and W106, W103 and W108 first, and then open the

connection terminals between W201 and W207, W202 and W206, W203 and W208. Refer to Figure 6-2 for

instructions on disconnecting the terminals.

Once the above operations are complete, the UPS is no longer connected to its internal batteries. At

this point it is safe to carry out maintenance work on the UPS since the battery terminals are completely de-

energized.

Figure 6-2 Schematic diagram for disconnecting internal battery terminals

User Manual 10H52260UM60 - Rev. 1 - 10/2017 71

Page 73

EXS

Once the maintenance work is complete, please wear arc protective gloves and arc protective clothing when

reconnecting the cabinet battery terminals and internal battery terminals. To reconnect the internal batteries in the

standard UPS, simply restore the connection terminals between W101 and W107, W102 and W106, W103 and W108; to

reconnect the internal batteries in the UPS with side cabinet, simply restore the connection terminals between W101

and W107, W102 and W106, W103 and W108 first, and then the connection terminals between W201 and W207, W202

and W206, W203 and W208.

Use a multimeter to check and ensure that the cabinet internal battery terminal poles are correct. Finally, replace

the front cover of battery compartment.

Warning

1. If maintenance is required, wait 10 minutes for the internal DC bus capacitors to discharge.

2. Hazardous voltages may be present on some parts of the UPS, even when the rectifier input switch, bypass input switch

and battery switch are disconnected. Therefore, UPS maintenance should be carried out by qualified personnel only.

6.11 Disposal of Used Batteries

If any of the batteries are found to be leaking, place them in a suitable container that can withstand sulphuric acid

and dispose of them in accordance with local regulations.

Lead-acid batteries are classified as hazardous waste material and represent a key item in the control of battery

pollution control. Batteries must be stored, transported, used and disposed of in accordance with national and local

legal requirements and all other criteria applicable to the treatment of hazardous waste material and waste battery

pollution prevention.

According to the applicable regulations, waste lead-aid batteries must be recycled, while all other disposal methods

are prohibited. Uncontrolled or random disposal of waste lead-acid batteries, or other improper disposal methods

can result in serious environmental pollution, which will be investigated by the relevant authorities.

72 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 74

EXS

Chapter 7 Parallel System and LBS System

This section provides information about installing parallel and LBS systems.

7.1 General

The parallel system may include up to four UPS modules of the same power rating and connected in parallel, without

the need for a centralized mains static bypass device. The bypass static switches of the individual UPS modules

share the load when the system transfers to the mains bypass supply.

From a 'power' viewpoint, each module is internally identical to the 'single module' configuration. A parallel system

requires inter-module control signals to manage load sharing, synchronizing and bypass switching. The control

signals are connected by means of the parallel cables, which are multi-way ribbon cables connected between the

units of the system to form a ring.

7.2 System Installation Procedures

The basic installation procedure of a parallel system consisting two or more UPS modules is the same as that for a

single module system. This section only covers the installation procedures that are specific to the parallel system.

When installing a parallel UPS system, follow the installation procedures for a single UPS module, with the additional

requirements detailed in this section.

Preliminary Checks

Make sure that correct parallel cable option has been selected, and that the module ratings, model, and software

and hardware releases are consistent.

Warning

To achieve coordinated operation of the modules in the parallel system, each module must be configured separately using

the VERTIV setting software. This must be done by VERTIV service personnel.

Cabinet Installation

Place the UPS modules side by side and interconnect them as shown in Figure 7-1. The output distribution mode

(Q1EXT, Q2EXT must be configured) shown in Figure 7-1 is recommended to facilitate maintenance and system

testing.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 73

Page 75

EXS

Figure 7-1 Circuit diagram of typical parallel system (with common input, separate batteries and output)

Power Cables

The power cable wiring is similar to that of the UPS module. Refer to 3.1 .

The bypass and rectifier input supplies must be use the same neutral line input terminal. If the input is fitted with a

current leakage protection device, the device must be fitted upstream of the neutral line input terminal.

Note

The power cables (including the bypass input cables and UPS output cables) of each UPS module should be of the same

length and specifications to facilitate load sharing.

Parallel cables

Shielded and double-insulated parallel cables must be interconnected in a ring configuration between the UPS

modules, as shown in Figure 7-2. Method: connect a parallel cable between the PARA1 port on one module and the

PARA2 port on the next module. Repeat this step for all the other parallel cables.

The ring connection ensures the reliability of the control of the parallel system. Be sure to verify that the cables are

connected securely before starting up the system!

74 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 76

EXS

Figure 7-2 Parallel signal cable connections (Parallel system)

Note

1. VERTIV parallel cables must be used for the parallel system.

2. If a parallel communication fault occurs during parallel commissioning or operation, switch the system off and check

whether the parallel cables are connected correctly.

3. Do not attempt to disconnect the parallel cables while the parallel system is operating as this could damage the system.

7.3 Operating Procedures for Parallel Systems

Warning

If UPS the input uses RCD devices, the differential switch should only used on the system bypass mains supply. At the

moment of electrical connection, current may not be immediately separated, which may cause the respective RCCB devices

to trip.

Proceed one step at a time, and only move on to the next time when the current operation has been completed for

all the UPS modules in the system.

Start-up Procedures In Normal Mode

These procedures are used to start the UPS starting from the fully switched off condition, which means that neither

the UPS or the maintenance bypass switch have supplied power to the load before. Make sure UPS has been

completely installed and commissioned by the engineer, and the external power supply switch is in the off position

Warning

User Manual 10H52260UM60 - Rev. 1 - 10/2017 75

Page 77

EXS

1. These procedures result in mains voltage being applied to the UPS output terminals.

2. If any loads are connected to the UPS output terminals, check with the user that it is safe to apply power. If the load is not

ready to receive power, please disconnect the downstream load switch, and apply a warning label at the load connection point.

Use the following procedures to switch the UPS on when it is in the fully switched off state.

1. Confirm that all the external maintenance bypass switches are in the off position. Ensure that the internal

maintenance bypass switch Q3 is in the off position, and that the input cables and copper bars and the parallel

cables are connected securely.

Warning

To avoid generating spurious fault messages, whenever it is necessary to switch the maintenance bypass switch to the on or off

position, the operation must be completed within three seconds.

2. Close all the bypass input switches.

3. Close the UPS bypass input switch Q2, rectifier input switch Q1, output switch Q5 and all external output isolating

switches (if any) in that order.

At this point, the system is switched on.

4. Press the UPS power buttons one by one to start the respective inverters.

Operating Procedures in Maintenance Bypass Mode

Warning

If the UPS system consists of more then 2 UPS modules in parallel, and the load capacity exceeds the single module capacity,

do not use the internal maintenance bypass switch.

This operation will transfer the load from the UPS power supply protection state to direct connection with AC input

bypass state.

Caution: risk of interruption of power supply to load

Before performing this procedure, you should check the LED information first, and make sure the bypass is normal and

synchronized with the inverter. Failure to do so may result in a brief interruption in the power supply to the load.

1. Remove the maintenance bypass switch baffle retaining screws, rotate the baffle upwards until it is locked in

position, and then fasten the retaining screws. Refer to Figure 5-13.

At this point, the system Interlock function has been activated and the UPS will transfer to internal bypass mode;

you should confirm that the UPS has been transferred to internal bypass mode.

2. After confirming, close the maintenance bypass switch Q3.

3. Disconnect the output switch Q5. At this point the load is powered by the maintenance bypass.

Caution

When the UPS is in maintenance bypass mode, the load is not protected against abnormalities in the mains power supply.

4. Unplugging the REPO terminal deactivates the rectifier, inverter, static switch and battery, but does not affect the

maintenance bypass power supply to the load.

Note

In maintenance mode, the load is fed directly by the mains power instead, of the pure AC power from the inverter.

5. If the UPS is equipped with an external battery, set the corresponding external battery switch to the off position

until all the UPS modules have been disconnected from the batteries.

76 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 78

EXS

6. Disconnect the rectifier input switch Q1 and bypass input switch Q2. At this point, all the internal power supplies

are deactivated and the LCD screen is switched off.

7. If the UPS is equipped with internal batteries, make sure that that they have been isolated from the UPS before

carrying out maintenance work on it. Refer to 6.10 for details.

Warning

1. If maintenance is required, wait 10 minutes for the internal DC bus capacitors to discharge.

2. Hazardous voltages may be present on some parts of the UPS, even when the rectifier input switch, bypass input switch

and battery switch are disconnected. Therefore, UPS maintenance should be carried out by qualified personnel only.

Procedures for Isolating One UPS Module from a Parallel System

Important

These procedures may only be carried out by VERTIV service personnel, or under their supervision.

Warning

Before operation, confirm that the system capacity has sufficient redundancy to avoid system shut down due to overload.

The following procedures apply when it is necessary to isolate one UPS module from the parallel system for repair

due to serious malfunction:

1. Unplugging the REPO terminal deactivates the rectifier, inverter, static switch and battery, while the other UPS

modules in the parallel system continue to supply the load as normal.

2. If the UPS is equipped with an external battery, simply set the corresponding external battery switch to off.

3. Set the rectifier input switch Q1, bypass input switch Q2 and output switch Q5 to off.

At this point, all the internal power supplies are deactivated and the LCD screen is switched off.

4. If the UPS is equipped with internal batteries, make sure that that they have been isolated from the UPS before

carrying out maintenance work on it. Refer to 6.10 .

Warning

1. Post a label on the AC input distribution line (generally at a distance from the UPS) to alert personnel that UPS

maintenance is in progress.

2. Wait 10 minutes for the internal DC bus capacitors to discharge. Then the UPS is completely shut down.

Procedures for Inserting One UPS Module into a Parallel System

Important

These procedures may only be carried out by VERTIV service personnel, or under their supervision.

The following procedures are used to reintegrate a UPS module that has been previously isolated from the parallel

system:

1. If the UPS his equipped with internal batteries, be sure to restore the connection between the UPS and internal

batteries after completing maintenance work on the UPS. Refer to 6.10 for details. Next, close the rectifier input

switch Q1.

At this point, the system is switched on.

2. Close the bypass input switch Q2.

3. Close the output switch Q5, and press the power button for two seconds.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 77

Page 79

EXS

Procedures For Completely Powering Down the UPS

In order to shut the UPS down completely and disconnect the power supply to the load, proceed as follows: All

power switches, isolating switches and breakers are switched to off, and the UPS no longer supplies power to the

load.

Caution

The following procedures will interrupt the power supply to the load, switching it off.

1. Unplug the REPO terminal on each UPS to deactivate the rectifier, inverter, static switch and battery.

2. If the UPS is equipped with an external battery, set the corresponding external battery switch to the off position

until all the UPS modules have been disconnected from the batteries.

3. Set the rectifier input switch Q1 and bypass input switch Q2 on each UPS to off. At this point, all the internal

power supplies are deactivated and the LCD screen is switched off.

4. Set the output switch Q5 on each UPS to off.

5. If the UPS his equipped with internal batteries, be sure to open the connection between the UPS and internal

batteries.

Warning

1. Post a label on the AC input distribution line (generally at a distance from the UPS) to alert personnel that UPS maintenance

is in progress.

2. Wait 10 minutes for the internal DC bus capacitors to discharge. Then the UPS is completely shut down.

Warning: hazardous battery voltage

Hazardous voltages are still present on the battery terminals, even after the UPS has been shut down.

Procedures for Shutting Down the UPS Completely While Maintaining Power to the Load

The following procedures may be used to shut the UPS down completely are applicable for completely, while

maintaining the power supply to the load. Refer to the procedures in 7.3.2 .

7.4 LBS System

Cabinet Installation

An LBS system consists of two independent UPS systems, each consisting of two parallel UPS modules, as shown in

Figure 7-3. The LBS system provides high reliability, which makes it suitable for use with loads having multiple input

terminals. In the case of single-input loads, an STS may be installed to power the load.

The system uses the LBS cables to synchronise the outputs of two independent (or parallel) UPS systems.

Place the UPS modules side by side and interconnect the UPS modules according to the following instructions.

78 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 80

EXS

Bypass

Rectifier

Q1 Q2

Bypass

UPS 1 ...... UPS 4

LBS

STS

To load

Figure 7-3 LBS system (UPS module)

Rectifier

Q1 Q2 Q3

Bypass

UPS 1 ...... UPS 4

Rectifier

Q1 Q2 Q3

Parallel

cable

Q1 Q2 Q3

STS

To load

LBS

Q1 Q2 Q3

Parallel

cable

Q1 Q2

Figure 7-4 LBS system (parallel system)

Note

In a dual-bus system, the two UPS systems must have the same power rating, voltage and frequency, and the load must not

exceed the power rating of a single UPS module system.

External Protective Device

Refer to 3.1.9 .

User Manual 10H52260UM60 - Rev. 1 - 10/2017 79

Page 81

EXS

Power Cables

The power cable of dual-bus power system is similar to that of single system. Refer to 3.1 Connecting the Power

Cables

LBS Cable

Note

1. The appearance of the LBS port is the same as the parallel port (see Figure 3-6).

2. In the case of dual bus systems consisting of parallel UPS units, we recommend preparing two LBS cables for connecting

any two parallel/LBS ports of the two parallel system, in order to guarantee a secure connection.

UPS1UPS2

Figure 7-5 LBS cable connections

See Figure 7-6 for the LBS parameters setting interface.

LBS parameter setting procedures.

Access 'Settings' -> 'System' -> 'LBS’ to set-up the LBS according to the specific requirements.

There are three items that may be selected during the LBS setting procedure: Disable, Slave, Master.

80 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 82

EXS

Figure 7-6 LBS parameter settings interface

The LBS is the load synchronisation system, and is used to synchronise the output voltage phases of the two

sections of the UPS system. The two sections of the UPS system may consist of two single UPS units, or two UPS

parallel systems.

'Master' and 'Slave' may be set-up manually via the LCD screen.

The UPS selected as the LBS master can send synchronization signals to LBS slave based on its inverter voltage

phase. After the slave receives the synchronization signal sent by the master, it will adjust its inverter voltage phase

so that it is synchronised with the master.

Thanks to this system, it is possible to synchronise the two sections of the UPS system, guaranteeing reliable

transfer between the respective output voltages and the STS, and hence a reliable, uninterrupted power supply to

the load.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 81

Page 83

Chapter 8 Options

This section lists the UPS options and provides information about installing and configuring the various options, and

their respective functions.

8.1 List of Options

See Table 8-1 for a list of the UPS options.

No. Option name Note Model

3-in 1-out copper bar

kit

32-block internal

battery kit (2-group)

32-block battery

internal kit (4-group)

Battery temperature

sensor kit

Table 8-1 Option list

Site installation EXS 0020kTSB01

EXS 0020kBSI02 (factory

installation, 9Ah battery)

Factory installation contains battery cables, trays and

batteries;

Site installation contains battery cables and trays.

Battery string should be user-prepared

EXS 0020kBSE02 (site

installation)

EXS 0020kBSI04 (factory

installation, 9Ah battery)

EXS 0020kBSE04 (site

installation)

Site installation EXS 0020kBDS02

EXS

Protective devices for short circuit withstand

current

6 Relay card UF-DRY410

7 UNITY-DP card IS-UNITY-DP

8 UNITY-LIFE card IS-UNITY-LIFE

9 Paralle cable

10 LBS cable ITA-20k00AL3A02C00L2

Backfeed protection

device

12 Intellislot extender kit EXS 0020kTH1AFN01Z5

EMC C2 kit

8.2 Option Introduction

Internal Battery Kit

Withstand current: 30kA, factory installation EXS 0020kTSB01

10m

Includes backfeed power board, cables, excitation tripping device; factory installation

Extend Intellislot from 1 to 2; factory installation.

ITA-20k00AL3A02C00L 1 ITA-20k00AL3A02CL3 ITA-20k00AL3A02EL1 ITA-20k00AL3A02EL2(only support 2 units parallel).

EXS 0020kBFP01

EXS 0020kTH1AFN01Z16.

VERTIV provides two kind of internal battery kits for the user when UPS internal battery or corresponding kits are

required. Kit A: 32-block internal battery kit (2-group, factory installation), or the required battery cables, battery

trays, screws (site installation); kit A: 32-block internal battery kit (4-group, factory installation), or the required

battery cables, battery trays, screws (site installation).

Table 8-2 Parameters of valve-regulated lead acid batteries

Capacity Dimensions Overall height (H) Container height (h) Length (L) Width (W)

9Ah mm (inch) 98.6±1 (3.88±0.04) 94.3±1 (3.71±0.04) 150.9±2 (5.94±0.08) 64.8±1(2.55±0.04)

82 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 84

EXS

Note

1. No batteries are supplied with the internal battery kit (site installation).

2. Battery cables and battery trays are designed according to the specifications of valve-regulated lead acid batteries 12V-

9Ah. If internal battery kits are required for site installation, please purchase batteries having the same specifications.

Preparation

re the installation tools, including a cross head screwdriver, a pair of insulated gloves, a sleeve, an ad

1. Prepa

spanne

r, and a multimeter.

2. Check tha

the correspo

t all installation materials are present and complete, including internal batteries, eight

nding battery power cables.

battery trays and

Procedures

hut down the UPS complete

1. S

a) Disco

b) Refer t

parallel s

c) All

nnect the load

o 5.6.1 Procedures For Completely Shutting Down the UPS for UPS module shut down, and 7.3.5

ystem shut down.

the LCDS are off, wait five minutes for the internal UPS DC bus capacitors to disc

ly.

harge fully.

2. Install the internal batteries.

justable

for

Installing standard UPS

a) Remo

b) Rem

ve the corresponding panels, as shown in Figure 8-1. Do not throw the screws away

ove the four battery accessory trays and position the batteries on them as shown in Figure 8-2, th

internal batteries

cable W104 and cable W105.

en connect

Front view Rear view

Figure 8-1 Removing the corresponding covers

User Manual 10H52260UM60 - Rev. 1 - 10/2017 83

Page 85

c) Insert four battery trays into the battery compartment (from bottom to top, see Figure 8-4). Connect cables

W106, W1

07 and W108 as shown in Figure 8-2, then use the screws (accessories) to secure the battery trays.

d) Connect the cables W101, W102 and W103 to the Bat+, N and Bat- terminals, respectively.

Note

The user must remove the insulating film before connecting the cables, and replace the insulating film after the connection procedure is complete

e) Connect the cables: W101 and W107, W102 and W106, W103 and W108.

f) Use a multimeter to guarantee the battery polarities are co

lace the cover on the battery co

g) Rep

mpartment.

rrect.

EXS

Figure 8-2 Installing standard UPS internal batteries

84 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 86

EXS

Installing internal batteries on UPS with side cabinet

a) Remove the

corresponding covers, as shown in Figure 8-3. Do not throw the screws away

Front view Rear view

Figure 8-3 Removing the corresponding covers

b) Remove the four battery trays for the standard UPS (accessories) and install batteries on their respective trays.

Connect cable W104 and cable W105, insert the four battery trays into the battery compartment (from bottom to

top, see Figure 8-4). Connect cables W106, W107 and W108 as shown in Figure 8-2, then use the screws

(accessories) to secure the battery trays.

b) Rem

ove the eight battery trays for the UPS with side cabinet (accessories), and install batteries on th

respective tra

ys. Connect cable W204, insert the eight battery trays into the battery compartment (from bottom to

eir

top, see Figure 8-4). Connect cables W205, W206, W207 and W208, then use the screws (accessories) to secure the

battery trays.

d) Connect the

User Manual 10H52260UM60 - Rev. 1 - 10/2017 85

cables W101/W201, W102/W202 and W103/W203 to the Bat+, N and Bat- terminals, respecti

vely.

Page 87

Note

The user must remove the insulating film before connecting the cables, and replace the insulating film after the connection procedure is complete.

EXS

e) Connect t

he cables: W101 and W107, W102 and W106, W 103 and W108, then connect cables: W201 and

W202 and W206, W203 and W208.

f) Use a multimeter to

lace the cover on the battery co

g) Rep

guarantee the battery polarities are correct

W207,

mpartment.

Battery trays for standard UPS

Battery trays for UPS with side cabinet

86 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 88

EXS

Figure 8-4 Installing battery trays and cable connections

Battery Temperature Sensor Kit

The battery temperature sensor is used for measuring the battery temperature. The battery temperature sensor is

installed next to the battery in order to measure the respective temperature. The sensor signal output cable is

connected to the multifunctional port, see port 8 (RJ45 port) in Figure 3-6. At this point the temperature sensor is

connected to the UPS internal logic circuit.

When this option is installed, the nominal float voltage supplied to the battery is varied so that it is inversely

proportional to the ambient temperature in the battery cabinet or battery room. This prevents the battery from

being over-charged at high ambient temperatures.

Preparation

1. P

repare the installation tools, including a cross head screwdriver.

Check tha

t all installation materials are present and complete, including a battery temperature sensor

Procedures

Warning

Shut the UPS down when installing the battery temperature sensor. Do not touch the battery terminals, exposed copper

bars or components during the installation procedure

User Manual 10H52260UM60 - Rev. 1 - 10/2017 87

Page 89

1. Shut down the UPS completely.

a) Disconnect the load

fer to 5.6.1 Procedures For Completely Shutting Down the UPS for single UPS module shut down, and 7.3.5 fo

b) Re

par

allel system shut down.

c) All the LCDS are off, wait five minutes for the internal UPS DC bus capacitors to discharge fully

2.Connect one

either port

end of the specified cable to either port of the battery temperature sensor, and the othe

of the UF-RS485 card. See Figure 8-5.

EXS

r end to

Figure 8-5 Connecting the UF-RS485 card to the battery temperature sensor

3. As shown in Figure 8-6, set DIP switch 5 to 'ON', so that the temperature sensor indicator in the bottom left corner

CD screen displays 01 (or 02). If two temperature sensors are used together, the corresponding DIP switch

of the L

settings may not coincide.

Figure 8-6 Temperature sensor DIP switch settings

4. Remove the left side panel of the cabinet, place the battery temperature sensor in the position shown in Figure 8-

7, and use the cable tie to secure it in place.

88 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 90

EXS

Figure 8-7 Installing and connecting the battery temperature sensor

5. Position the cables in order. Note that the cables should be routed separately from the power cables to avoid EMI.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 89

Page 91

8.2.3

Relay Card

The UPS is available with a relay card that enables users to use dry contact signals to monitor the UPS. It is hot

pluggable for easy installation.

The relay card can provide up to four digital relay output signals for connection to remote monitoring devices.

These signals are: UPS on Battery, Battery Low, UPS on Bypass or in Standby, UPS Faulty. Each dry contact signal

output channel provides both normally open and normally closed ports. The relay card can also handle up to three

digital signal inputs, two of which control the UPS switch-on and switch-off functions, while the third is reserved.

Appearance and description of hardware

The appearance of the relay card is shown in Figure 8-8.

DIP sw

itcith

P sw

DB25 connector

B25 connector

EXS

Figure 8-8 Relay card appearance

The DIP switch is used to configure the UPS switch-on and switch-off signal input functions on the relay card. The

DB25 connector provides dry contact signal inputs and outputs. For a description of the DB25 connector pins, see

Table 8-3.

90 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 92

EXS

)

Table 8-3 DB25 connector pin description

Pin No. Pin name Description Pin 1 Va, power output 9 - 15Vdc (reserved for factory use) Pin 14 K0_NO, Channel 0 dry contact normally open output contact Closed: UPS on Battery Pin 2 K0_COM, Channel 0 dry contact common output contact Pin 15 K0_NC, Channel 0 dry contact normally closed output contact Open: UPS on battery Pin 3 K1_NO, Channel 1 dry contact normally open output contact Closed: Battery Low Pin 16 K1_COM, Channel 1 dry contact common output contact Pin 4 K1_NC, Channel 1 dry contact normally closed output contact Open: Battery Low

Pin 17 K2_NO, Channel 2 dry contact normally open output contact

Closed: UPS on Bypass or in Standby

Pin 5 K2_COM, Channel 2 dry contact common output contact

Pin 18 K2_NC, Channel 2 dry contact normally closed output contact

Open: UPS on Bypass or in Standby

Electrical parameter: 30Vdc/1.8A, resistive load

Pin 6 K3_NO, Channel 3 dry contact normally open output contact Closed: UPS Fault Pin 19 K3_COM, Channel 3 dry contact common output contact Pin 7 K3_NC, Channel 3 dry contact normally closed output contact Open: UPS Fault Pin 24 DRY_IN2, Channel 2 dry contact signal input Reserved

Pin 12 DRY_IN1, Channel 1 dry contact signal input

Pin 25 DRY_IN0, Channel 0 dry contact signal input

The UPS is switched off if this contact is closed for more than one second The UPS is switched on if this contact is closed

for more than one second Pin 9 RXD_PC, for communication to PC, receive terminal Reserved, for factory commissioning Pin 21 TXD_PC, for communication to PC, send terminal Reserved, for factory commissioning

Pin 13 GND, common GND

Power GND, dry contact signal input common

GND Others NC

Cable options

VERTIV provides three cable options for connections to the DB25 connector of the relay card, depending on the

user’s requirements

Figure 8-9 - Figure 8-11 show the appearance and wiring principle of each cable.

DB25 male (pin-type

DB25 male (pin-type)

1 14 2 15 3 16 4 17 5 18 6 19 7 20 8 21 9 22 10 23 11 24 12 25 13

re 8-9 Appearance and wiring diagram of cable 1 (UFDRY21SL1)

Figu

K0_NO K0_COM K0_NC K1_NO K1_COM K1_NC K2_NO K2_COM K2_NC K3_NO K3_COM K3_NC

User Manual 10H52260UM60 - Rev. 1 - 10/2017 91

Page 93

DB25 male (pin-type

)

DB25 male (pin-type)

13 25 12 24 11 23 10 22 9 21 8 20 7 19 6 18 5 17 4 16 3 15 2 14 1

X14J7A plug (pin-type)

1 2 3 4 5 6 7

EXS

Installation

Figure 8-10 Appeara

This end is labelled 'UPS'

This end is labelled "UPS"

DB25 male (pin-type)

nce and wiring diagram of cable 2 (UFDRY21SL2)

13 25 12 24 11 23 10 22 9 21 8 20 7 19 6 18 5 17 4 16 3 15 2 14 1

560 ohm/1W

Figure 8-11 Appearance and wiring dia

DB25 male (pin-type)

gram of cable 3 (UFDRY21SL3)

9 22 10 23 11 24 12 25 13

Note

Some electronic components on the relay card are sensitive to static electricity. To prevent static electricity from damaging

the relay card, do not touch its electronic components or circuits, also make sure that they do not come into contact with

live parts. Please hold the relay card by its edges when handling or installing it.

1. Set the DIP switch on the relay card.

Skip this step if you do not need to control the UPS switch-on and switch-off functions via the relay card.

The location of the DIP switch is shown in Figure 8-12. It is a

n 8-bit DIP switch. Its factory default setting is shown

in Figure 8-6.

OFF

12345678

ure 8-12 DIP switch factory default setting

Fig

Bits 1 through 7 are designed for use in the factory, the user is not permitted to change their default settings. Bit 8 is

used to configure the UPS switch-on and switch-off signal input function on the relay card, see Table 8-4 for

instructions on how to set it.

92 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 94

EXS

Table 8-4 Setting the UPS switch-on and switch-off signal input function

Bit 8 Function

ON UPS switch-on and switch-off signal input function enabled

OFF UPS switch-on and switch-off signal input function disabled

2. Insert the relay card into the UPS.

Note

The relay card is hot-pluggable, therefore it may be installed without shutting the UPS down.

a) Remove the Intellislot port cover (see Figure 3-6) on the front panel. Do not throw the screws away.

b) Align the relay card with the Intellislot port, insert the relay card into the port along the grooves on both sides of

the port.

c) Secure the relay card in place through the fixing holes on the relay card panel using the screws from step a).

onnect the cable.

3. C

You can select an optional cable according to your needs, or prepare your own, in accordance with Table 8-4 and

Figure 8-

card, and the other end to the user equipment.

9 - Figure 8-11. Connect the cable end with the DB25 male connector to the DB25 connector of the relay

8.2.4

Warning

The DB25 connector must be connected to a SELV circuit. Failure to observe this could damage the relay card and even

lead to accidents.

Troubleshooting

See Table 8-5 for relay card troubleshooting information.

Table 8-5 Troubleshooting

No. Problems Corrective measures

The dry contact output signal remains the same when

the UPS status changes

The UPS does not respond to the UPS switch-on dry

contact input signal

Check that the relay card has been inserted into the

Intellislot port correctly

Verify that bit 8 of the DIP switch of the relay card has been

set to the 'ON' position

IS-UNITY-DP Card

Important

We recommend using shielded cables in order to increase EMC.

The appearance of IS-UNITY-DP card is shown in Figure 8-13.

Figure 8-13 IS-UNITY-DP card

User Manual 10H52260UM60 - Rev. 1 - 10/2017 93

Page 95

For a detailed description of the IS-UNITY-DP card, refer to Liebert IntelliSlot Unity Card User Manual–Web, SNMP,

Modbus, BACnet, YDN23, which is available as an accessory.

IS-UNITY-LIFE Card

8.2.5

We recommend using shielded cables in order to increase EMC.

EXS

Important

The appearance of the IS-UNITY-LIFE card is

For a detailed description of the IS-UNITY-LIFE card, refer to Liebert IntelliSlotTM Unity Card User Manual-Web,

SNMP, Modbus, BACnet, YDN23, which is available as an accessory.

3-in 1-out Copper Bar Kit

8.2.6

This kit may be used to convert the system to the 3-in 1-out configuration. This kit contains three copper shorting

bars that are used to connect the rectifier input (common input configuration), bypass input (split-bypass

configuration), and output terminals together.

Note

The UPS is set to 3-in 3-out mode by default. If you need to convert it to 3-in 1-out mode, contact VERTIV authorized

personnel for the corresponding settings.

shown in Figure 8-14.

Figure 8-14 Appearance of IS-UNITY-LIFE card

Always observe the following procedures:

Power distribution mode

1. 3-in 1-out, common input configuration

Remove the three copper shorting bars from the rectifier input terminals mA, mB and mC, see Figure 8-15.

Figure 8-15 3-in 1-out, common input configuration (1)

b) Install the copper shorting bars on the input terminals (mA, bA, bB, bC), and use the output shorting copper bars to connect the output terminals (oA, oB, oC) together. See Figure 8-16.

94 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 96

EXS

Figure 8-16 3-in 1-out, common input configuration (2)

c) Connect the phase A input cables to the input copper shorting bars, and connect the input N line to the neutral

terminal 'N' in the cabinet. Connect the phase B and phase C cables respectively to terminals mB and mC, and then

connect the I/O earth cables to the PE terminal in the cabinet.

d) Connect the output cable to the output copper shorting bar, and the output N line to the output N copper

shorting bar.

e) Connect the battery positive, battery N and battery negative respectively to the Bat+, N, Bat- terminals.

2. 3-in 1-out, split bypass configuration

Remove the three copper shorting bars from the rectifier input terminals mA, mB and mC, see Figure 8-17.

Figure 8-17 3-in 1-out, split bypass configuration (1)

b) Install the bypass input copper shorting bars to terminals (bA, bB, bC), and use the output shorting copper bars to connect the output terminals (oA, oB, oC) together. See Figure 8-18.

Figure 8-18 3-in 1-out, split bypass configuration (2)

User Manual 10H52260UM60 - Rev. 1 - 10/2017 95

Page 97

C) Connect the phase A, phase B and phase C input cables to terminals (mA, mB and mC), and connect the bypass

input cables t

o the bypass input copper shorting bar. Connect the input N line to the neutral terminal 'N' in the

cabinet, then connect the I/O earth cables to the PE terminal in the cabinet.

Connect the output cable to the output copper shorting bar, and the output N line to the output N co

shorting bar

onnect the battery positive, battery N and battery negative respectively to the Bat+, N, Bat- terminal

This c

oncludes the power distribution changes and cable connections.

pper

Start-up procedures

Use the following procedures to switch the UPS on when it is in the fully switched off state.

nsure that the internal maintenance bypass switch Q3 is off, and that the input cables and copper bars ar

1. E

connec

ted securely. Ensure that the input cables and copper bars are connected securely according to the 3-in 1-

out power distribution mode configuration.

Warning

To avoid generating spurious fault messages, whenever it is necessary to switch the maintenance bypass switch to the on or off

position, the operation must be completed within three seconds.

2. Before switching the system on, use a multimeter to measure the voltage on the rectifier terminals (mA-mB-mC),

and make sure that there are no circuits; if so, check that the connections are correct.

3. Unplug the REPO terminal at rear of the cabinet, and then close the rectifier input switch Q1, at this point the

system is switched on.

EXS

4. Press , and access -> Settings (default password is ‘111111’) -> Output -> Output phase No., then set the

system to ‘1 phase’. After the system is switched off, switch it on again, access this menu once more and confirm

that this setting has been applied.

Figure 8-19 Prompt window

5. Set the rectifier input switch Q1 to the off position to shut the UPS down completely.

6. Plug-in the REPO terminal, close the UPS bypass input switch Q2 and the rectifier input switch Q1 in that order.

At this point, the system is switched on.

7. After the rectifier starts, close the output switch Q5 and all the external output isolation switches (if any).

8. Press the power button for two seconds to start the inverter.

96 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 98

EXS

Protective Devices For Short Circuit Withstand Current

8.2.7

This kit contains three bypass fuses (one fuse for each phase) designed to guarantee the UPS withstand short circuit at 30kA. If this kit is installed, please refer to Figure 8-20 for the fuse blow-out curve when choosing the

UPS downstream switch and transformer load.

Manufacturer: Bussmann, model: 100FE

Figure 8-20 Schematic diagram of fuse blow-out

Manufacturer: Vicfuse, model: VBS1749-100A

User Manual 10H52260UM60 - Rev. 1 - 10/2017 97

Page 99

Chapter 9 Service And Maintenance

This section focuses on UPS maintenance, including fan maintenance, battery maintenance, UPS cleaning, UPS

state checks, and UPS function checks.

Note

Never attempt to carry out maintenance on the UPS while it is on line. Ensure that the UPS has been switched off completely

when performing any internal maintenance operations on it.

9.1 Fan Maintenance

Note

In order to avoid injury or damaging the device, wait until the fan is completely stationary before inserting fingers or any tools

into it.

The UPS fans are expected to run for 20,000 hours - 40,000 hours in continuous operation. The higher the ambient

temperature, the shorter the fan life.

During the UPS operation, it is important to check the condition of the fans at least once a year by confirming that

they blow air out of the ventilation holes on the rear panel.

EXS

9.2 Battery Maintenance

Warning

1. Never invert the battery connections as this could result in fires.

2. Never attempt to open batteries since they contain electrolyte which is potentially harmful to personnel. In the event of

accidental with electrolyte, wash the affected area with abundant, clean water, and seek medical assistance immediately.

The internal UPS battery module houses a sealed, lead-acid, maintenance-free battery. The battery life depends on

the ambient temperature, and charge and discharge times. High ambient temperatures and heavy discharge cycles

will shorten the battery life.

To preserve the battery life, it is necessary to:

Maintain the ambient temperature between 15°C and 25°C

Prevent small current discharge. DO NOT operate the UPS in battery mode for periods in excess of 24 hours.

Charge the battery for at least 12 hours if it hasn't been charged for three months while the ambient temperature

remains within the specified limits, or two months in the event of high ambient temperatures

Note

1. Check the battery connection screws at regular intervals, and re-tighten them if necessary.

2. Make sure that all the safety devices are present, in good condition and that they function correctly, and make sure that the

battery management parameter settings are correct.

3. Measure and log the ambient temperature in the battery room.

4. Check whether the battery terminals are damaged or hot, and check the condition of the cases and the covers.

If any

of the batteries are found to be leaking, place them in a suitable container and dispose of them in accordance

with local regulations.

Lead-acid batteries are classified as hazardous waste material. The control of waste battery pollution is a nationally

important issue. Batteries must be stored, transported, used and disposed of in accordance with national and local

legal requirements and all other criteria applicable to the treatment of hazardous waste material and waste battery

pollution prevention.

98 User Manual 10H52260UM60 - Rev. 1 - 10/2017

Page 100

EXS

According to the applicable regulations, waste lead-aid batteries must be recycled, while all other disposal methods

are prohibited. Uncontrolled or random disposal of waste lead-acid batteries, or other improper disposal methods

can result in serious environmental pollution, which will be investigated by the relevant authorities.

As a provider of lead-acid batteries, VERTIV has developed a dedicated service network and waste battery recycling

system to assist users to dispose of waste batteries legally. Contact VERTIV or your nearest service centre for

detailed information about the waste battery the recycling system.

VERTIV may not be held liable for the environmental impact resulting from the failure to comply with the guidelines

set out in this section, or to use the waste battery recycling system offered by VERTIV.

9.3 Cleaning the UPS

Clean the UPS periodically, especially the ventilation holes, to ensure free airflow inside the UPS. If necessary, clean

the UPS with a vacuum cleaner. Confirm that the ventilation holes are unobstructed.

9.4 Checking the UPS Status

We recommend checking the operational state of the UPS at least twice a year.

Check the following items:

1. Check for any UPS fault conditions: Is the FAULT indicator on? Are there any UPS alarms active?

2. Check if the UPS is operating in Bypass mode. Under normal conditions, the UPS operates in Normal mode; if you

find that it is operating in Bypass mode, determine the reason (operator intervention, overload, internal fault, etc.)

3. Check if the battery is discharging: When the AC mains supply is within normal limits, the battery should not be

discharging; if you find that it is operating in Bypass mode, determine the reason (mains failure, battery test,

operator intervention, etc.)

9.5 Checking the UPS Functions

Note

Checking the UPS functions may interrupt the power supply to the load!

We recommend checking the UPS functions at least twice a year.

Backup the load data before conducting the UPS functional check. The procedures are as follows:

1. Press the power button to check if the buzzer beeps, the indicators are on and the LCD display is normal.

2. Press the power key and check again that the indicators are on, the LCD display is normal, and that the UPS has

been transferred to inverter mode.

User Manual 10H52260UM60 - Rev. 1 - 10/2017 99