Page 1
590-1491-501A
1
VERTIV™ AVOCENT® SV 220H/240H/340H
2 and 4-Port HDMI KVM Switches
Quick Installation Guide
The following instructions will help
you install your Vertiv™ Avocent® SV
220H/240H/340H switch.
1. Connecting local peripherals
Turn o all computers you
plan to use with your SV
220H/240H/340H switching
system. Plug the monitor cable
into the appropriate CONSOLE
port on the back of the switch.
Plug the USB keyboard cable, USB
mouse cable and two audio cables
(speaker/headset and microphone)
into the appropriate ports.
2. Connecting computers to the
switch
Make sure all computers are
turned o. Plug the monitor, audio
cables, keyboard and mouse
cables from the corresponding
computer into one of the ports
on the switch. Repeat for all
computers.
3. Turn on your system
Turn the monitor on. Plug the
power supply cord into the switch.
Plug the other end of the power
supply cord into an AC wall outlet.
The display diagnostic LED should
be solid green a few seconds after
power is applied. This indicates the
display EDID information has been
captured and secured.
4. Turning on the computers
Turn on all the attached
computers and check for display
and peripheral functionality.
5. Operating your switch
When the computers are turned
on, the computer connected to
port 1 will be displayed on the
monitor. You can control the SV
switch by using the front panel
push-buttons.
1
2
3
1
Vertiv™ Avocent® SV 340H Switch Shown
Page 2
VertivCo.com | Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA
© 2017 Verti v Co. All righ ts reser ved. Vertiv and the Ver tiv logo are trademar ks or regis tered trad emarks of Ver tiv Co. All o ther name s and logo s referred to are trade na mes, tra demarks o r
registe red trade marks of the ir respe ctive owne rs. Whil e every pre caution h as been taken to ensur e accurac y and compl etenes s herein , Vertiv Co. assumes n o responsibility, and disclai ms all
liability, for damages resulting from use of this information or for any errors or omissions. Specications are subject to change without notice.
590-1491-501A
2
VERTIV™AVOCENT® SV 220H/240H/340H
Quick Installation Guide
Supported Hardware
The HDMI KVM switches support most
HDMI 1.4 monitors and video cards,
DVI-I monitors and video cards (with
adaptors), speakers/headsets, USB
keyboards and USB mice.
NOTE: If a DVI-I display is used, then all
computers must be connected through
a DVI-I interface.
Environmental
Operating temperature is 32° to 104° F
(0° to 40° C).
Storage temperature is -4° to 140° F
(-20° to 60° C).
Humidity requirements are 0-80%
relative humidity, non-condensing.
Mechanical
SV 220H Approximate
Dimensions
W x D x H: 7 x 2.4 x 1.4 inches
(177 x 61 x 35.2 mm)
Weight: 1.1 lbs (0.5 kg)
SV 240H Approximate
Dimensions
W x D x H: 13.5 x 5 x 1.7 inches
(342 x 125 x 42 mm)
Weight: 3.5 lbs (1.6 kg)
SV 340H Approximate
Dimensions
W x D x H: 13.5 x 5 x 2.2 inches
(
342 x 125 x 56.6 mm)
Weight: 4 lbs (1.85 kg)
Supported Resolution
HDMI 1.4 4k-2k resolutions (up to 3840
x 2160 pixels).
Cables
User can choose from 6 ft. or 12 ft.
cables for either USB or PS/2 and
select whether or not to use CAC
functionality.
Contact a Vertiv representative for
ordering details.
Loading...