Vertex VX-2000V Service manual

Download

Page 1

VHF Land Mobile Transceiver

VX-2000V

Service Manual

VERTEX STANDARD CO., LTD.

4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

VERTEX STANDARD

US Headquarters

10900 Walker Street, Cypress, CA 90630, U.S.A.

International Division

8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.

YAESU EUROPE B.V.

P.O. Box 75525, 1118 ZN Schiphol, The Netherlands

YAESU UK LTD.

Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K.

VERTEX STANDARD HK LTD.

Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong

40 channel version 4 channel version

Introduction

This manual provides technical information necessary for servicing the VX-2000V VHF Land Mobile transceiver.

The VX-2000V is carefully designed to allow the knowledgeable operator to make nearly all adjustments required for various station conditions, modes and operator preferences simply from the controls on the panels, without opening the case of the transceiver. The VX-2000V Operating Manual describes these adjustments, plus certain internal settings.

Servicing this equipment requires expertise in handling surface mount chip components. Attempts by non-qualified persons to service this equipment may result in permanent damage not covered by warranty.

For the major circuit boards, each side of the board is identified by the type of the majority of components installed on that side.

In most cases one side has only chip components, and the other has either a mixture of both chip and lead components (trimmers, coils, electrolytic capacitors, packaged ICs, etc.), or lead components only.

While we believe the technical information in this manual is correct, Vertex Standard assumes no liability for damage that may occur as a result of typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies in the technical information would be appreciated. Vertex Standard reserves the right to make changes in this transceiver and the alignment procedures, in the interest of technological improvement, without notification of the owners.

Operating Manual Reprint............................ 2

Specifications................................................... 7

Exploded View & Miscellaneous Parts....... 8

Block Diagram ................................................. 9

Interconnection Diagram............................. 13

Circuit Description ...................................... 15

Alignment....................................................... 19

Board Unit (

MAIN Unit ............................................................... 23

DISPLAY-1 Unit ...................................................... 49

DISPLAY-2 Unit ...................................................... 53

VR Unit ..................................................................... 57

MIC Unit .................................................................. 58

Schematics, Layouts & Parts

)

Page 2

Operating Manual Reprint

CONTROLS & CONNECTORS

40 channel version4 channel version

Microphone Jack

Connect the microphone plug to this jack.

MONI Button & Indicator

This button selects the “squelch” (receiver mute) mode. When the yellow indicator is off, “tone” or “coded” squelch is active. When the indicator glows steadily, only “noise squelch” is active, and any signal present on the channel will be heard. When the indicator is blinking, the squelch is disabled, and background noise will be heard if no signal is present.

A Button & Indicator

This button is provided for an ACCESSORY function such as HIGH/LOW POWER selection, “TALK-AROUND”, or “CALL ALERT” functions. The green “A” indicator will be illumi- nated when this function is active.

VOLUME and POWER ON/OFF Knob

This knob adjusts the receiver volume, and turns the radio off when turned all the way to the left into the click-stop.

TX/BUSY Indicator Lamp

This lamp blinks red when the channel is busy, and glows steadily red during transmission. Do not transmit when this

indicator is blinking, as a courtesy to other users of the channel.

The following item is unique to the 4-channel radio versions:

CHANNEL Numbered Indicators & Button

Press the CHANNEL button to select the operating channel; the channel number currently in use will light up on the display panel.

The following items are unique to the 40-channel radio versions:

CHANNEL Selector Buttons (p) and (q)

Push one of these keys to select the operating channel, as shown on the display.

Numeric Channel Display

This display area shows the channel number and prioritychannel/scan status.

SEL/PRI Button

This button is used to select a channel for “Priority” monitoring, and is used together with the SCAN button to select the desired scanning mode.

SCAN Button

This button is used to activate scanning, to select or remove channels on the scanning list, and (together with the SEL/

PRI button) to select scanning mode.

P Indicator

This small dot indicates Priority Channel status (described later).

E Indicator

This small dot indicates Scanning on/off status (described later).

Page 3

REAR (Heatsink)

13.6V DC Cable Pigtail w/Connector

The supplied DC power cable must be affixed to this 2-pin connector.

Antenna Socket

The 50-ohm coaxial feedline to the antenna must be connected here, using a “UHF” type (PL-259) plug.

Operating Manual Reprint

External Speaker Jack

An external loudspeaker may be connected to this 2-contact, 3.5-mm miniature phone jack.

DSUB 9-Pin Data Connector

External Transmit Audio input, PTT (Push To Talk), Squelch, and Receive Audio output signals may be obtained from this connector for use with accessories such as a data transmission/reception modem, etc.

Page 4

Operating Manual Reprint

OPERATION

Power ON/OFF

Turn the VOLUME/POWER knob clockwise to turn on the radio. The active display and channel indicators will become illuminated, indicating the status of the radio. The channel indicated will be the same one on which you were operating when the radio was last turned off.

Setting the Channel

In 4-channel versions, press the CHANNEL button to change channels. In 40-channel versions, the display will show either a channel number or a Scan Mode indicator (Sc, Ur, SP or UP). If a Scan Mode indicator is displayed, press the SCAN button momentarily so that a channel number is displayed; then press either the UP (p) or DOWN (q) button to change channels.

Setting the Volume

Rotate the VOLUME/POWER knob clockwise to increase the volume level. If no signal is present on which to adjust the volume level, push and hold in the MONI button for two seconds; the yellow “MONI” indicator will blink, and either background noise or a voice signal will be heard. You may now adjust the VOLUME/POWER knob for a comfortable listening level. When you are done, press the MONI button momentarily to return to silent monitoring.

Transmitting

To transmit, wait until the “TX/BUSY” indicator is off (this indicates that the channel is not in use). Then press the PTT (Push- To-Talk) switch on the side of the microphone; while holding in the PTT switch, speak in a normal voice level across the face of the microphone. During transmission, the red “TX/BUSY” indicator will glow steadily. When you are done transmitting, release the PTT switch; the VX-2000 will revert to the “receive” mode.

The remaining instructions apply to 40-channel trans-

Scanning

To activate scanning on your radio, first place the microphone in its hanger. Now press the SCAN button momentarily. The radio will scan in one of four available Scan Modes (detailed below), and will halt when a signal is received which contains the correct code to open your squelch. Scanning will resume automatically either after a preset interval of a few seconds, or after the other station stops transmitting (depending on how your radio was programmed).

The four Scan Modes, and their corresponding displays, are:

Display Scanning function

Sc Scan all channels Ur Scan only user-selected channels SP Monitor one channel plus dealer-designated Priority Channel(s) UP Scan user-selected channels plus uer-designated Priority Channel(s)

The user-selected channels for the Ur and UP Scan Modes are ones you can set up yourself, as described at the right. The “Priority” channels are those on which signals will take priority over signals received on other channels; that is, if a signal appears on a Priority Channel while another appears on a nonpriority channel, the Priority Channel signal will be heard, and not the other. Up to two of the installed channels may be designated by your Dealer as pre-programmed Priority Channels for the SP mode (the radio will not indicate which they are), and you can additionally program any two channels as “User Priorities” for the UP mode. In the SP mode, the non-priority channel will be the last one displayed. When a Scan Mode is displayed, you can select another by pressing the SEL/PRI button repeatedly (the display will cycle through the above selections). Note that the radio will not scan if the microphone is not in its hanger.

ceiver versions only

Special Transmitter Functions

If your VX-2000 is programmed for Busy Channel LockOut, the transmitter will not activate when the PTT switch is

pressed unless the “TX/BUSY” indicator is off (so as to prevent interference to other users of the same channel). If the selected channel has been programmed for Automatic Time-Out, you must limit the length of your transmissions. While transmitting with this feature activated, a “beep” will sound ten seconds before the timer expires, and then another “beep” sound as the timer expires: the “TX/BUSY” indicator will shut off, and transmission will cease. Release the PTT switch, listen for a moment, then press PTT again to resume transmission. This feature prevents interference to other users caused by a microphone which accidentally is stuck in the “transmit” position (wedged between seats of a car, etc.).

Page 5

Operating Manual Reprint

USER PROGRAMMABLE CHANNEL SELECTIONS

You can program a list of channels to be scanned, and up to two channels to be monitored on a “priority” basis. Your selections will be maintained in memory until you change or delete them.

Setting of these channels involves two small “Dot” indicators at the top of the channel display field. The Dot to the left of the first digit is the “P” (Priority) indicator, while the Dot to the left of the second digit is the “E” (Enable for Scanning) indicator.

To create or modify the Scan and Priority selections, first turn the radio off. Now press and hold in the SCAN button while you turn the transceiver back on; continue to hold the SCAN button in for two seconds after the radio has come on, then you may release it. Now press the UP (p) or DOWN (q) button repeatedly, and note whether or not the “E” (right dot) or “P” (left) dots appear on any of your channels. If a dot appears by any channel, it means that it has been designated as either a Scan-Enabled or Priority channel, respectively. To enable or disable a channel from the User Scan list, press the SEL/PRI button momentarily. The “E” dot will appear or disappear, as appropriate. To change the Priority Channels, first cancel both by selecting either, and then pressing the SEL/PRI button momentarily. Now select the channel you wish to designate as the 1st Priority Chan-

nel, and hold in the SEL/PRI button for 2 seconds, until a beep sounds and the “P” indicator blinks. If you wish to designate a 2nd Priority Channel, move to that channel, and again hold in the SEL/PRI button for 2 seconds; this time, the “P” indicator will glow, but will not blink. If you have deleted a channel from Priority status, you must reenable it for scanning if you want it to be included on your Scan List. Press the SEL/PRI button momentarily to do this.

Coded Squelch - the MONI Button

Your transceiver may be programmed so that when the microphone is removed from its hanger, coded squelch is defeated, and you can hear any signal on the channel (the yellow “MONI” indicator will be lit). You can get the same result, without lifting the microphone, by pressing the MONI button momentarily. To avoid listening to unnecessary chatter, keep the microphone in its hanger, and press the MONI button when necessary to turn the yellow indicator off (unless you want to listen to other calls on the channel). Holding the MONI button in for two seconds defeats both the coded squelch and noise squelch, so background noise can be heard (the “MONI” indicator will blink in this case). Press the MONI button momentarily to return the yellow indicator to its previous state (either off or steadily on).

OPTIONAL ACCESSORIES

CE-20 Programming Software (for IBM PC/compatibles only) VPL-1 Programming Cable T9101411 Radio-to-Radio Cloning Connection Cable FP-1025A Heavy-Duty (20A) AC Power Supply MD-11A8J Desktop Microphone MH-600D DTMF Back-lit Microphone w/Autodial MLS-100 External Loudspeaker LF-1 DC Line Filter VTM-20 VX-Trunk II Trunking Mobile Logic Board F2D-4A/B 2-Tone Decoder Unit FTE-18 ANI Unit

Page 6

Operating Manual Reprint

J1003 DSUB 9-Pin Data Connector Pin Assignment

ÃÄ Â Á À

È Ç Æ Å

À SQ: Squelch Signal Output

Carrier In: Active High (5 V / 47 kΩ)

Á RX_AUD_OUT: Received Audio Output (Two choices available)

Á-1 De-Empasized Audio Output: 100 mV / 10 kΩ

This output level's default state is fixed at the factory by having no jumper at JP1003 and soldering the jumper at JP1002 on the MAIN Unit.

Á-2 Flat / Unmuted Audio Output: 250 mV / 10 kΩ

(Unsolder the jumper at JP1002 and solder a jumper at JP1003 on the MAIN Unit to activate Á-2)

Â EXT_MIC: External MIC Audio Input (Two choices available)

Â-1 Pre-Emphasized / IDC / Splatter Filtered Audio Input:

2.5 mV / 600 Ω

This input is fixed at the factory by attaching capacitor C1254 across JP1005 and soldering a jumper at JP1004 on the MAIN Unit.

Â-2 Flat (Non-Pre-Emphasized) Audio Input: 650 mV / 10 kΩ

(Remove the jumper at JP1004 and solder a jumper across JP1005 on the MAIN Unit to activate Â-2)

Ã Not Used Ä GND: Ground Å A_OUTPUT: Accessory Output (Two choices available)

Å-1 Not Used

This is the default setting at the factory (no jumper across JP1001 on the MAIN Unit).

Å-2 Accessory Output: Open Collector Output

"A" Lamp ON: Low, "A" Lamp OFF: Open Maximum voltage: 13.8 V, Maximum sink current 5 mA (Solder a jumper at JP1001 on the MAIN Unit to activate Å-2)

Æ PTT: External PTT Signal input

GND: TX, Open: RX

Ç 5 V

Switched and regulated DC 5 V output for supplying power to an accessory. Maximum output current is 50 mA.

È Not Used

Page 7

Specifications

General

Frequency Range (version): 134 ~160 or 148 ~ 174 MHz (VHF vers. A/C, respectively)

No. of Channels & Spacing: 4 or 40 channels 25-kHz, 12.5-kHz spacing

Modes of Emission: 16K0F3E ,11K0F3E

Frequency Stability: ±0.00025%

Antenna Requirements: 50 ohms, unbalanced (SO-239 socket)

Voltage Requirements: 11.8 V to 15.6 V DC, negative ground

Current Consumption (approx.): 250 mA Stby, 200 mA Rx, 6.5 A Tx

Operating Temperature Range: -30 °C to +60 °C (-22 °F to +140 °F)

Size (WHD, approx.): 160 × 40 × 105 mm (6¼ × 1½ × 4¼ inches)

Weight (approx.): 0.85 kg (1.9 lbs.)

Receiver

Receiver Circuit Type: Double-Conversion Superheterodyne

Intermediate Frequencies: 17.7 MHz , and 450 kHz (all models)

Sensitivity: 0.2/0.25 µV for 12-dB SINAD

0.3/0.35 µV for 20 dB NQ

Hum & Noise Ratio: Better than 45 dB for 25-kHz/step,

Better than 40 dB for 12.5-kHz/step

Adjacent Channel Selectivity: >70 dB for 25-kHz/step,

>60 dB for 12.5-kHz/step

Intermodulation Distortion: Better than 65 dB

Spurious Rejection: Better than 65 dB

External Audio Output Power: 5 watts into 4 ohms with <10% THD

Transmitter

Power Output: 25/5 watts (high/low, programmable)

Modulation Type/Deviation: Frequency Modulation, ±5 kHz (±2.5 kHz )

Hum & Noise Ratio: Better than 45 dB for 25-kHz/step,

Better than 40 dB for 12.5-kHz/step

Modulation Distortion: Less than 5%

Spurious Emissions: Better than 65 dB (below carrier)

Microphone Impedance: 600 ohms

Specifications are subject to change without notice or obligation.

Page 8

Exploded View & Miscellaneous Parts

VXSTD P/NREF. U24208001 TAPTITE SCREW M2.6X8 (Lot. 1~5) 1

U20208001 BINDING HEAD SCREW M2.6X8 (Lot. 6~) 1

U20306002 BINDING HEAD SCREW M3X6NI 4 U23205001 TAPTITE SCREW M2.6X5 4

U23206001 TAPTITE SCREW M2.6X6 3

U24306002 TAPTITE SCREW M3X6NI 5

U31206007 OVAL HEAD SCREW M2.6X6B 7

U24308001 TAPTITE SCREW M3X8 1

RA0034900 RUBBER KNOB (4CHANNEL)

CP6003001 PANEL-SUB A ASSY

Description

DISPLAY-1 Unit

MAIN Unit

Qty.

P1090654 CONNECTOR

VXSTD P/N

Q0000062 FUSE 10A 2 T9021810 DC CABLE 1

RA0060100 CASE

Description

T9206675 WIRE ASSY

P1090984 CONNECTOR

Qty.

RA0015600 RUBBER KNOB (40 CHANNEL)

R6054387B SPECIAL NUT

RA001330A KNOB

VR Unit

MIC Unit

NAME PLATE RA0013900 (EXPORT) RA0014000 (VTX(USA))

M4090122 SPEAKER

CP6007001 PANEL-SUB B ASSY

RA0056000 RA005600A (Lot. 4~) RA005600B (Lot. 6~)

DISPLAY-2 Unit

RA00560AB (NTL: Lot. 53~) RA005600C (Lot. 68~) RA00560AC (NTL: Lot. 68~) CHASSIS

Non-designated parts are available only as part of a designated assembly.

Page 9

VX-2000V 4ch Front Panel Block Diagram

Block Diagram

VX-2000V 40ch Front Panel Block Diagram

Page 10

Block Diagram

Note:

Page 11

VX-2000V Main Unit Block Diagram

Block Diagram

Page 12

Block Diagram

Note:

Page 13

VX-2000V 4ch Front Interconnection Diagram

Interconnection Diagram

(T9206689A: Lot 7~)

Page 14

Interconnection Diagram

VX-2000V 40ch Front Interconnection Diagram

(T9206689A: Lot 7~)

Page 15

Circuit Description

Receive Signal Path

Incoming RF energy from the antenna jack is

delivered to the MAIN Unit, and passes through

a low-pass filter consisting of coils L1001, L1002,

L1004, and L1006, capacitors C1002, C1006,

C1009, C1017, C1019, C1022, C1041, and C1046,

and switching diodes D1002 (UM9957F) and D1006 (RLS135), then delivered to the receiver

front end.

The RF energy then enters a varactor-tuned

bandpass filter, consisting of coils L1008, L1010,

L1011, L1013, L1014, T1001, and T1002, capaci-

tors C1045, C1052, C1054, C1057, C1058, C1069,

C1072, C1073, C1091, C1092, C1093, C1094,

C1096, C1097, C1100, C1101, C1105, C1106,

C1109, and C1110, plus diodes D1007/1008 (both

KV1470) and D1011~1014 (all HVU350). After

bandpass filtering, the in-band RF signals are

amplified by RF preamplifier Q1012 (2SC4226),

then delivered to the first mixer stage.

Buffered output from the VCO is amplified by

Q1038 (2SC5107), providing a pure local signal

between 130.3 and 156.3 MHz for injection to the

(CFWM450G) or CF1002 (CFWM450E) to strip

away unwanted mixer products, and then is ap-

plied to the limiter amplifier in Q1029, which re-

moves any amplitude variations in the 450 kHz IF.

Speech detection by CD1001 (CDBM450C24T)

is then performed, converting the second IF into

an audio signal.

Detected audio from Q1029 is amplified by

Q1017-1 (NJM2904V) and then applied to the de-

emphasis network, consisting of capacitors

C1084/C1089, resistors R1038/R1049, and Q1007-

4 (NJM2902V). The de-emphasized audio is then

applied to CTCSS subsystem IC Q1009

(MX165BDW), which contains the TX/RX audio

filter, CTCSS decoder and CTCSS encoder; if a

CTCSS tone is present on the incoming signal, it

is removed by the high-pass audio filter in Q1009.

The processed signal then passes through the

audio mute gate Q1008 (DTC323TK) and the

volume control, then enters the audio power

amplifier Q1003 (TDA2003H), which provides up

to 2 Watts of audio power to the external speak-

er jack.

first mixer, Q1021 (SGM2016). The resulting 17.7

MHz first IF then passes through monolithic crys-

tal filter XF1001, which strips away all but the

desired signal, and the signal is then amplified

by Q1026 (2SC4215Y). The amplified first IF sig-

nal is then applied to FM subsytem IC Q1029

(BA4116FV), which contains the second mixer,

a limiter amplifier, and a noise amplifier.

The second local oscillator signal is generated

by PLL reference/2nd LO transistor Q1047

(2SC4116GR), using the 17.25 MHz oscillator

crystal X1002 as a reference. This signal is mixed

with the 17.7 MHz local at Q1029, producing a

450 kHz second IF. The second IF signal then

passes through ceramic filter CF1001

Squelch Control

The squelch circuitry consists of a noise am-

plifier, bandpass filter, and noise detector with-

in Q1029, plus control circuitry within micropro-

cessor Q1039 (MB89677).

When no carrier is received, noise at the out-

put of the detector stage in Q1029 is amplified,

bandpass filtered, and detected by Q1029. The

resulting DC squelch control voltage is passed

to pin 33 of microprocessor Q1039. With no car-

rier being received, pin 33 remains low, signal-

ing pin 5 of Q1039 to keep the green "BUSY" LED

off, and simultaneously signaling pin 19 of Q1039

to command audio mute gate Q1008 to block re-

ceived audio.

Page 16

Circuit Description

When a carrier appears at the discriminator,

noise is removed from the output, causing pin 33

of Q1039 to go "high," in turn causing the "BUSY"

LED and audio output lines to turn on. The mi-

croprocessor then checks for CTCSS information.

If CTCSS decode is not activated, or if CTCSS de-

code is activated and a signal carrying a matching

tone is received, the microprocessor allows audio

to pass through AF mute gate Q1008 and audio

amplifier Q1003 to the speaker.

Transmit Signal Path

Speech input from the microphone is delivered to the MAIN Unit, where it passes through the preemphasis network (R1015 and C1031). The preemphasized speech signal proceeds through the AF high-pass filter at Q1009, then is applied to the IDC (Instantaneous Deviation Control) at

Q1016-3 (NJM2902V), with deviation level being

set by potentiometer VR1001. The audio then pass-

Automatic Transmitter Power Control

RF output from the final amplifier is sampled

by C1039 and C1051 and rectified by D1005

(1SS321). The resulting DC voltage is fed through Automatic Power Controller Q1014 (2SB1143S), Q1015 (2SC4116GR), and Q1017-2 to effect con-

trol of the gain of transmitter PA Q1011. The mi-

croprocessor, Q1039, issues commands for setting

"HIGH" or "LOW" power output.

Transmit Inhibit

When the transmit PLL is unlocked, pin 2 of

PLL IC Q1050 (SC370651F) goes to logic "low"

level. The resulting DC unlock control voltage

switches off the TX inhibit switch Q1022 (IMZ1),

which interrupts the supply voltage to the trans-

mitter PA, Q1011, thus disabling the transmitter.

Spurious Suppression

Generation of spurious products by the trans-

es to a splatter filter in sections 1 and 4 of Q1016, which filters out high-frequency components which could result in over-deviation.

The processed audio is mixed with the CTCSS tone (if activated) generated by CTCSS subsystem

IC Q1009, then delivered to D1041 (1SV276) for

frequency modulation of the PLL carrier (at the transmitting frequency) up to ±5 kHz from the unmodulated carrier frequency.

The modulated signal from the VCO, Q1046

(2SC5107), is buffered by Q1038 and Q1044 (both 2SC5107). The low-level transmit signal is then amplified by Q1028 and Q1031 (both 2SC3357),

then applied to the final amplifier, Q1101

(M67741H), providing 25 Watts of transmitter

power. The transmit signal then passes through the antenna switch, D1003/D1004 (both

UM9957F) and low-pass filter (which suppress-

es harmonic spurious radiation) before delivery

to the antenna jack.

mitter is minimized by the fundamental carrier

frequency being equal to the final transmitting

frequency, modulated directly in the transmit

VCO. Additional harmonic suppression is pro-

vided by a low-pass filter consisting of L1001,

L1002, L1007, C1002, C1006, C1009, C1017,

C1019, C1036, and C1053, resulting in more than

60 dB of harmonic suppression prior to delivery

of the RF signal to the antenna jack.

PLL Frequency Synthesizer

The Phase-Locked Loop (PLL) circuitry on the

MAIN Unit includes VCO Q1046, VCO buffer

Q1044, and PLL subsystem IC Q1050, which in-

cludes a reference divider, serial-to-parallel data

latch, programmable divider, phase comparator,

and charge pump.

Stability of the reference oscillator, Q1047, is

maintained by a regulated 5 Volt supply, which

includes Q1001 (MM1216EN), Q1002

Page 17

Circuit Description

(2SB1201STP-FA), Q1040 (2SC4116GR), and D1029 (02CZ5.6Y), with temperature compen-

sation provided by thermistors TH1003/TH1004

and capacitors associated with the 17.25 MHz

reference crystal, X1002.

In the receive mode, VCO Q1046 oscillates

between 130.3 and 156.3 MHz, according to the

transceiver version and the programmed receiv-

ing frequency. The VCO output is buffered by

Q1044, and applied to the prescaler section of

Q1050. There the VCO signal is divided by 64 or

65, according to a control signal from the data

latch section of Q1050, before being applied to

the programmable divider section of Q1050. The

data latch section of Q1050 also receives serial

dividing data from the microprocessor, Q1039,

which causes the pre-divided VCO signal to be

quency of the VCO according to the phase dif-

ference between the signals derived from the

VCO and the crystal reference oscillator. The

VCO is thus phase-locked to the crystal reference

oscillator. The output of the VCO is then deliv-

ered to the first mixer via buffer amplifier Q1051.

For transmission, the VCO Q1046 oscillates

between 134 and 174 MHz, according to the mod-

el version and the programmed transmit frequen-

cy. The remainder of the PLL circuitry is shared

with the receiver section. However, the dividing

data from the microprocessor is such that the

VCO frequency is at the actual transmitting fre-

quency (rather than being offset by the IF, as in

the receiving case). Also, the VCO is modulated

by the speech audio applied to D1041 (1SV276),

as described previously.

further divided in the programmable divider sec-

tion, depending on the desired receive frequen-

cy, so as to produce either a 5.0 kHz or 6.25 kHz

derivative of the current VCO frequency.

Meanwhile, the reference divider section of

Q1050 divides the 17.25 MHz crystal reference

frequency by 3450 (or 2760) to produce the 5 kHz

(or 6.25 kHz) loop reference (respectively). The

5 kHz (or 6.25 kHz) signal from the programma-

ble divider (derived from the VCO) and that de-

rived from the reference oscillator are applied to

the phase detector section of Q1050, which pro-

duces a pulsed output with pulse duration de-

pending on the phase difference between these

input signals. The pulse train is filtered to DC

and returned to varactors D1035/D1036/D1038/

D1039 (all 1SV276).

Changes in the level of the DC voltage applied

Receive and transmit buses select which VCO

is made active via Q1048 (DTC124EU). FET Q1043 (2SK880GR) buffers the VCV line for ap-

plication to the tracking bandpass filters in the

receiver front end.

Push-To-Talk (PTT) Transmit Activation

The PTT switch on the microphone is connect-

ed to pin 24 of microprocessor Q1039, such that

when the PTT switch is closed, pin 24 of Q1039

goes low . This signals the microprocessor's pin

35 to activate the TX/RX controller Q1004 (IMH6),

which in turn disables the receiver by disconnect-

ing the 9 Volt supply bus at Q1006 (DTB123EK)

to the receiver front end, FM subsystem IC, and

receiver VCO circuitry. At the same time, Q1005

(DTB123YK) activates the TX 9 Volt supply line

to enable the transmitter.

to the varactors affect the reactance in the tank

circuit of the VCO, changing the oscillating fre-

Page 18

Circuit Description

Channel Selection & Display

(4-channel version)

The CHANNEL button on the front panel causes

microprocessor Q1039 to select the operating fre-

quency and CTCSS frequency data from serial

EEPROM Q1049 (BR93LC66RF). The operating

frequency data is in the form of PLL dividing

ratios, which are passed to the PLL IC on the

MAIN Unit via strobe, data, and clock outputs on

pins 43, 42, and 41 respectively. The channel digit

display data from the microprocessor is strobed

by pin 46 to display latch Q2002 (BU4094BCFV)

on the DISPLAY-1 Unit, which decodes the data

and drives the four channel LEDs and the func-

tion indicator LEDs.

Channel Selection & Display

(40-channel version)

The UP and DOWN buttons on the front panel

cause microprocessor Q1039 to select the oper-

ating frequency and CTCSS frequency data from

serial EEPROM Q1049. The operating frequency

data is in the form of PLL dividing ratios, which

are passed to the PLL IC on the MAIN Unit via

strobe, data, and clock outputs on pins 43, 42,

and 41 respectively. The channel digit display

data from the microprocessor is strobed by pin

46 to display latch Q3001 (DN8657S) on the DIS-

PLAY-2 Unit, which decodes the data and drives

the two 7-segment LEDs and the function indi-

cator LEDs.

Page 19

Alignment

The VX-2000 is carefully aligned at the facto-

ry for the specified performance across the de-

signed frequency range. Realignment should,

therefore, not be necessary except in the event of

a component failure, or when altering the fre-

quency range (“version”).

The following procedures cover the sometimes-

critical and tedious adjustments that are not nor-

mally required once the transceiver has left the

factory. However, if damage has occurred and

some parts subsequently are replaced, alignment

may be required in order to restore the original

alignment. If a sudden problem occurs during oth-

erwise normal operation, it is likely due to part

failure, and realignment should be performed only

after the faulty component has been replaced.

All component replacement and service

should be performed only by an authorized Ver-

tex representative, or the warranty policy may

be voided. Vertex service technicians are experi-

enced with the circuitry, and are fully equipped

for part replacement and alignment. When any

repairs are completed, Vertex service technicians

perform comprehensive performance checks to

ensure that total transceiver system performance

complies with each and every specification for

this product.

Those who undertake any of the following

alignment procedures are cautioned to proceed

at their own risk. Problems caused by unautho-

rized attempts at realignment are not covered by

the warranty policy covering this transceiver.

Also, Vertex reserves the right to change circuits

and alignment procedures, in the interest of im-

proved performance, without notifying owners.

Under no circumstances should any alignment

be attempted unless the normal function and op-

eration of the radio are fully understood, the cause

of the malfunction has been clearly pinpointed and

any/all faulty components replaced, and realign-

ment determined to be absolutely necessary.

Required Test Equipment

The following test equipment (and thorough

familiarity with its correct use) is necessary for

complete realignment. Correction of problems

caused by misalignment resulting from the use

of improper test equipment is not covered by our

warranty policy.

While most steps do not require all the test

equipment listed, the interactions of some adjust-

ments may require that more complex adjust-

ments be performed afterwards. Do not, there-

fore, attempt to perform only a single step un-

less it is clearly isolated electrically from all oth-

er steps. Have all test equipment ready before

beginning, and follow all of the steps in a section

in the order presented.

r RF Signal Generator with calibrated output to

200 MHz

r Deviation Meter (linear detector)

r In-line Wattmeter with 5% accuracy at 200 MHz

r 50-W Dummy Load with a power rating of 50

W at 200 MHz

r Regulated DC Power Supply, adjustable from

10 V to 17 V DC at 10 A

r Frequency Counter with 0.2 ppm accuracy at

200 MHz

r AF Signal Generator

r DC Voltmeter, high impedance

r SINAD Meter

r IBM PC

Windows® v3.1 (or later) installed

r Vertex VPL-1 Connection Cable and CE-20

Channel Programming Diskette

r VHF Sampling Coupler

/compatible computer with Microsoft

Page 20

Alignment

Alignment Preparation & Precautions

Before beginning alignment, connect the trans-

ceiver to the PC using the VPL-1 Connection Ca-

ble, and upload the current frequency data from

the customer’s radio to the computer; save this

information to disk so that it can be downloaded

to the radio again after alignment is completed.

Next, refer to the label at the rear of the bot-

50 W

Dummy Load

In-Line

Wattmeter

Deviation

meter

Frequency

Counter

RF Sampling

Coupler

CT-71 Connection cable

COM Port

RF Signal Generator

Transceiver

Generator

Power Supply

13.8 V

tom cover of the radio to determine its “version”

(frequency range); using the CE-20 software, pro-

gram the four “Test” simplex channels shown in

the table below, as appropriate for the radio ver-

sion you are working with:

Channel #

1 2 3 4

Version “A”

134.000 MHz

147.000 MHz

160.000 MHz

Version “C”

148.000 MHz

161.000 MHz

174.000 MHz

Download this data to the transceiver under test.

Note: When alignment is finished, you may wish to

save these alignment channels as a disk file for

future service work. Make certain to re-load the

original channel data (uploaded from the radio

prior to servicing) into the transceiver, and com-

plete a final performance check, before return-

ing the equipment to the customer.

Alignment Setup

same test equipment will be required. If not, re-

move the test equipment (except dummy load

and wattmeter) before proceeding.

Correct alignment requires that the ambient

temperature be the same as that of the transceiv-

er, and that this temperature be held constant

between 68°F and 86°F (20°C and 30°C). When

the transceiver is brought into the shop from hot

or cold air, it should be allowed time to come to

room temperature before alignment is attempt-

ed. All test equipment should similarly be thor-

oughly warmed up.

Whenever possible, alignments should be per-

formed with oscillator shields and circuit boards

firmly affixed in place.

A 50-W dummy load and in-line wattmeter

must be connected to the rear-panel antenna jack

in all procedures which require transmission.

Correct alignment is not possible without a re-

sistive 50-W termination for the transmitter.

Be certain that your power supply delivers

13.8 VDC, as measured directly at the radio's DC

input plug, during transmitter tests. Any volt-

age drop in the cable, or due to the loading on

the power supply, must be compensated to 13.8

VDC for accurate alignment.

After completing one alignment step, read the

following step to determine whether or not the

Note: Signal levels in dB referred to in these align-

ment procedures are based on 0 dBµ = 0.5 µV

(closed circuit).

Connect the test equipment as shown in the

pictorial above.

PLL VCV (Varactor Control Voltage)

Performance Check

r Connect the DC voltmeter between test point

TP1033 on the MAIN Unit and chassis ground.

r Set the transceiver to channel 3, and confirm

that the reading is about 4.5V.

Page 21

Alignment

r Now select channel 1, and confirm that the

reading changes to about 1.0V for Version A,

or 0.8V for Version C.

r Again select channel 3. Key the transmitter,

and confirm that the voltmeter reading is ap-

proximately 4.5V.

r Once more select channel 1 and again key the

transmitter. Confirm that the voltmeter read-

ing is approximately 1.0V for Version A, and

at least 1.0V for Version C.

PLL Reference Frequency

r With the wattmeter, dummy load, and fre-

quency counter connected to the antenna jack,

select channel 2.

r Key the transmitter, and adjust TC1001 on the

MAIN Unit, if necessary, so that the counter fre-

nels 1 and 3, and confirm that 30 Watts of RF

power is present on the band edge channels.

r Using the computer, re-program channel 1 for

“LOW” power output, and download this

data to the transceiver.

r Select channel 2, and adjust (“HIGH” power)

potentiometer VR1002 for 25 Watts of RF power.

r Select channel 2, and adjust “LOW” power) po-

tentiometer VR1003 for 5 Watts of RF power.

Transmitter Deviation

r Select channel 2, and adjust the AF genera-

tor’s attenuator so as to deliver 25 mV output

at 1 kHz to the microphone jack.

r Key the transmitter, and adjust VR1001 (MAIN

Unit) for ±4.3 kHz deviation as measured on

the deviation meter (tolerance: 100 Hz).

quency is within 200 Hz of 147.000.00 MHz for

version A, or 161.000.00 MHz for version C.

Transmitter Output Power

r Preset trimmer potentiometer VR1002 (MAIN

Unit) fully clockwise.

r Select (Band center) channel 2. Key the trans-

mitter, and confirm that at least 30 Watts of

power output is measured. Now select chan-

VR1001

r On the computer, re-program channel 2 to en-

able a 100 Hz CTCSS (encode) tone, and down-

load this data to the transceiver.

r Reduce the AF generator’s output to zero. Key

the transmitter, and adjust VR1004 (MAIN

Unit) for ±800 Hz deviation on the CTCSS tone

(within 100 Hz).

r On the computer, re-program channel 2 to en-

VR1006 VR1002

VR1004 VR1005 TP1033 TC1001

MAIN Unit Alignment Points

VR1003

Page 22

Alignment

able DCS code 627 (encode), and download

this data to the transceiver.

r With the AF generator still set to zero, key the

transmitter, and adjust VR1005 (MAIN Unit)

for ±900 Hz deviation on the DCS signal (with-

in 100 Hz).

Receiver Squelch Threshold

r Set the transceiver to channel 2. Set the RF sig-

nal generator to the same frequency (147.000

for version A, 161.000 MHz for version C). Set

the signal generator’s output to -8 dBµ.

r Adjust VR1006 (MAIN Unit) clockwise until

the squelch just closes, and then counterclock-

wise until the squelch just opens.

r Turn off the signal generator, and confirm that

the squelch again closes when the RF input

Restore Original Channel Data

r When all alignment steps have been complet-

ed, re-load the original channel data from your

computer’s disk, and download it to the trans-

ceiver.

signal disappears.

Page 23

MAIN Unit (Lot. 1~)

Circuit Diagram

13.8 (13.8)

0 (0)

13.8 (13.5)

8.9 (8.9)

0.1 (8.2)

5.0 (0)

0 (8.4)

8.9 (0.1)

2.9 (4.3)

13.8 (13.5)

2.6 (2.7)

0.8 (0.1)

0 (7.0)

13.5 (7.5)

8.9 (0.1)

6.4 (0.1)

0 (1.2)

13.5 (12.8)

0 (1.9)

0 (2.1)

2.9 (2.1)

6.5 (0.1)

0 (0)

0 (4.3)

0 (0)

2.8 (4.0)

0.7 (0)

3.4 (0)

0 (4.7)

3.4 (4.0)

8.8 (0.1)

0.6 (0.1)

1.4 (0)

4.9 (5.0)

4.7 (0.1)

0.7 (0)

0 (8.4)

1.7 (1.7)

0.19V

5.5 (0.1)

0 (0)

2.1 (2.1)

5.6 (0.1)

P-P

0.1 (0.7)

0.9(0)

5.0 (0.1)

0(0)

4.2 (0)

0 (0)

2.1 (2.1)

3.8 (3.8)

7.5 (7.4)

7.1 (7.0)

0 (5.1)

0 (6.7)

5.6 (5.5)

6.1 (0)

0.98V

1.5 (0.1)

0.8 (-0.2)

4.7 (0)

5.1

0.46V

P-P

(0.1)

0.6 (0)

0.7 (0)

0.13V

4.0 (4.0)

P-P

3.9 (4.0)

P-P

2.6 (2.7)

4.4 (4.4)

4.9 (4.9)

2.0 (2.2)

2.9 (3.1)

2.6 (2.5)

2.5 (2.5)

4.7 (4.7)

2.2 (2.4)

8.9 (8.9)

4.5 (4.5)

4.7 (4.7)

0.60mV

100mV

P-P

0 (1.6)

P-P

3.2 (2.3)

1.7 (1.7)

5.5 (5.5)

0.6 (0.6)

2.3V

P-P

2.0 (2.0)

5.0 (5.0)

0.4 (0.4)

5.0 (5.0)

8.4V

6.7(6.4)

0.1 (0.3)

0 (0)

4.7 (0.5)

P-P

72mV

P-P

13.6 (13.6)

0.8 (0.8)

4.0 (4.0)

1.3 (1.3)

7.7V

4.0 (4.0)

P-P

8.9 (8.9)

4.0 (4.0)

0 (0)

96mV

0 (4.7)

490mV

4.9 (4.9)

5.0 (5.0)

2.1 (2.3)

0.1 (0)

3.9 (3.9)

13.0 (12.8)

6.3 (6.3)

4.9 (4.9)

4.8 (4.7)

4.9 (4.9)

0 (0)

4.9 (4.9)

4.8 (4.8)

4.9 (4.9)

2.2 (2.2)

5.5V

2.2 (2.4)

450mV

2.5 (2.5)

P-P

2.5 (2.5)

4.9 (4.9)

1.9V

4.0 (4.0)

0 (0)

3.2 (3.2)

P-P

0 (0)

137mV

4.0 (4.0)

0 (4.9)

5.0 (5.0)

0.94V

2.0 (2.0)

4.3 (7.8)

P-P

4.0 (4.0)

2.0 (2.0)

1.44V

2.3 (2.3)

0 (0)

4.9 (4.9)

5.0 (5.0)

8.9 (8.9)

3.2 (3.2)

P-P

5.0 (5.0)

4.9 (4.9)

13.8 (13.7)

P-P

3.6V

P-P

2.5 (2.7)

2.0 (1.9)

4.0 (0.5)

3.8V

P-P

2.0 (2.0)

0.93V

2.0 (2.0)

P-P

1.7 (1.7)

P-P

0 (4.9)

4.9 (0) 0 (0.4)

4.9 (4.9) 0 (0)

0 (4.8) 0 (0)

0 (0)

0 (4.7)

0 (0)

5.0 (0.7)

0 (0)

1.9 (1.9)

3.2 (3.2)

4.9 (4.9)

4.6 (0.1)

5.0 (5.0)

0 (0)

13.8 (13.7)

4.6 (0.1)

XX : RX 160.025MHz, wide, Inject +30dBµ at ±3.0kHz deviation (XX): TX 160.025MHz, Hi power, Inject – 43.5dBm at 1kHz tone

4.9 (4.9)

0 (0)

4.9 (4.9)

4.6 (0)

4.3 (4.3) 80mV 0 (0)

P-P

8.9 (8.9)

0 (0)

5.0 (5.0)

13.8 (13.7)

Page 24

MAIN Unit (Lot. 1~)

Note:

Page 25

Parts Layout

A C E FB D G H

MAIN Unit (Lot. 1~)

MB89P677ARFM (Lot. 1~) MB89677ARPFM (Lot. 2~) (Q1039)

SC370651FR2 (Q1050)

MX165BDW (Q1009)

BA4116FV (Q1029)

NJM2902V (Q1007, 1016)

NJM2904V (Q1017)

TDA2003H (Q1003)

2SB1143S (Q1014)

MA143 (MC) (D1017)

DAP202U (P) (D1016, 1037)

KV1470 (F7) (D1007, 1008)

DTC124EU (25) (Q1053) (Q1048: Lot. 1)

2SC3357 (RK) (Q1031)

SGM2016M (M-) (Q1021)

2SK880GR (XG) (Q1043)

IMZ1 (Z1) (Q1022)

Side A

IMH6 (H6) (Q1035)

HA17805P (Q1010)

RH5VL45AA (D5) (Q1036)

2SB1201STP (Q1002)

2SC4116GR (LG) (Q1015, 1042) (Q1048: Lot. 2~) 2SC4215Y (QY) (Q1026) 2SC4226 (R24) (Q1012) 2SC5107O (MFO) (Q1044, 1046)

Page 26

MAIN Unit (Lot. 1~)

A C E FB D G H

Side B

M67741H-01 (Q1011)

MM1216ENRE (1A) (Q1001)

BR93LC66RF (Q1049)

AN8005M (Q1030)

IMH6 (H6) (Q1004, 1025, 1052)

2SC3357 (RK) (Q1028)

DTB123EK (F12) (Q1006)

DTB123YK (F56) (Q1005: Lot. 1~)

DTC124EU (25) (Q1020, 1033, 1051)

DTB113ZK (G11) (Q1005: Lot. 4~)

2SC4116GR (LG) (Q1040, 1045, 1047) 2SC5107O (MFO) (Q1038, 1041)

2SA1586Y (SY) (Q1032, 1034)

HZM7C (24) (Lot. 2~) (D1024)

DTC323TK (H02) (Q1008)

MA143 (MC) (D1040)

1SS321 (F9) (D1005, 1026) MA142WK (MU) (D1019)

02CZ5.6Y (5.6) (D1018, 1029) (D1024: Lot. 1)

Page 27

Circuit Diagram

MAIN Unit (Lot. 5~)

Page 28

MAIN Unit (Lot. 5~)

Note:

Page 29

Parts Layout

A C E FB D G H

MAIN Unit (Lot. 5~)

MB89P677ARFM (Lot. 1~) MB89677ARPFM (Lot. 2~) (Q1039)

SC370651FR2 (Q1050)

MX165BDW (Lot. 1~) MX165CDW (Lot. 6~) (Q1009)

BA4116FV (Lot. 1~) TA31136FN (Lot. 7~) (Q1029)

NJM2902V (Q1007, 1016)

NJM2904V (Q1017)

TDA2003H (Q1003)

2SB1143S (Q1014)

MA143 (MC) (D1017)

DAP202U (P) (D1016, 1037)

KV1470 (F7) (D1007, 1008)

DTC124EU (25) (Q1053) (Q1048: Lot. 1)

2SC3357 (RK) (Q1031)

SGM2016M (M-) (Lot. 1~) SGM2016AM (MA) (Lot. 8~) (Q1021)

2SK880GR (XG) (Q1043)

IMZ1 (Z1) (Q1022)

Side A

IMH6 (H6) (Q1035)

HA17805P (Q1010)

RH5VL45AA (D5) (Q1036)

2SB1201STP (Q1002)

2SC4116GR (LG) (Q1015, 1042) (Q1048: Lot. 2~) 2SC4215Y (QY) (Q1026) 2SC4226 (R24) (Q1012) 2SC5107O (MFO) (Q1044, 1046)

Page 30

MAIN Unit (Lot. 5~)

A C E FB D G H

Side B

M67741H-01 M67741L-01 (Ver A: Lot. 6~) (Q1011)

MM1216ENRE (1A) (Q1001)

BR93LC66RF (Q1049)

AN8005M (Q1030)

IMH6 (H6) (Q1004, 1025, 1052)

2SC3357 (RK) (Q1028)

DTB123EK (F12) (Q1006)

DTB123YK (F56) (Q1005: Lot. 1~)

DTC124EU (25) (Q1020, 1033, 1051)

DTB113ZK (G11) (Q1005: Lot. 4~)

2SC4116GR (LG) (Q1040, 1045, 1047) 2SC5107O (MFO) (Q1038, 1041)

2SA1586Y (SY) (Q1032, 1034)

HZM7C (24) (Lot. 2~) (D1024)

DTC323TK (H02) (Q1008)

MA143 (MC) (D1040)

1SS321 (F9) (D1005, 1026) MA142WK (MU) (D1019)

02CZ5.6Y (5.6) (D1018, 1029) (D1024: Lot. 1)

Page 31

Circuit Diagram

MAIN Unit (Lot. 19~)

Page 32

MAIN Unit (Lot. 19~)

Note:

Page 33

Parts Layout

A C E FB D G H

MAIN Unit (Lot. 19~)

MB89P677ARFM (Lot. 1~) MB89677ARPFM (Lot. 2~) MB89P677APFM (NTL: Lot. 53~) MB89677ARPFM (EXP, STANDARD, VTX: Lot. 53~) (Q1039)

SC370651FR2 MC145192FR2 (Lot. 26~) MC145193FR2 (Lot. 41~) (Q1050)

MX165BDW MX165CDW (Lot. 6~) (Q1009)

BA4116FV TA31136FN (Lot. 7~) (Q1029)

MA143 (MC) (D1017)

DAP202U (P) (D1016, 1037)

KV1470 (F7) KV1870STL (Lot. 44-) (D1007, 1008)

DTC124EU (25) (Q1053) (Q1048: Lot. 1)

2SC3357 (RK) (Q1031)

SGM2016M (M-) (Lot. 1~) SGM2016AM (MA) (Lot. 8~) (Q1021)

TDA2003H (Q1003)

2SK880GR (XG) (Q1043)

2SB1143S (Q1014)

IMZ1 (Z1) (Q1022)

Side A

HA17805P (Lot. 1~75) (Q1010)

IMH6 (H6) (Q1035)

NJM2902V (Q1007, 1016)

KIA7805API (Lot. 76~) (Q1010)

RH5VL45AA (D5) (Lot. 1~) RH5VT45AA (Lot. 19~) RH5VL45AA (D5) (Lot. 22~) (Q1036)

NJM2904V (Q1017)

2SB1201STP (Q1002)

2SC4116GR (LG) (Q1015, 1042) (Q1048: Lot. 2~) (Q1054: Lot. 26~) 2SC4215Y (QY) (Q1026) 2SC4226 (R24) (Q1012) 2SC5107O (MFO) (Q1044, 1046)

Page 34

MAIN Unit (Lot. 19~)

A C E FB D G H

Side B

M67741H-01 (Q1011)

MM1216ENRE (1A) (Q1001)

BR93LC66RF BR93L66RF (Lot. 85~) (Q1049)

AN8005M (Q1030)

IMH6 (H6) (Q1004, 1025, 1052)

2SC3357 (RK) (Q1028)

DTB123EK (F12) (Q1006)

DTB123YK (F56) (Q1005: Lot. 1~)

DTC124EU (25) (Q1020, 1033, 1051)

DTB113ZK (G11) (Q1005: Lot. 4~)

2SC4116GR (LG) (Q1040, 1045, 1047) 2SC5107O (MFO) (Q1038, 1041)

2SA1586Y (SY) (Q1032, 1034)

HZM7C (24) (Lot. 2~62) (D1024)

DTC323TK (H02) (Q1008)

HZM7.5NB (Lot. 63~) (D1024)

1SS321 (F9) (D1005, 1026) MA142WK (MU) (D1019)

02CZ5.6Y (5.6) (D1018, 1029) (D1024: Lot. 1)

MA143 (MC) (D1040)

Page 35

Parts List

MAIN Unit

REF.

C 1001 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B f1 C 1002 CHIP CAP. 8pF 200V CH GRM40CH080D200PT K22230214 1-5 A G1 C 1002 CHIP CAP. 10pF 200V CH GRM40CH100D200PT K22230216 VERSION A 6- A G1 C 1002 CHIP CAP. 8pF 200V CH GRM40CH080D200PT K22230214 VERSION C 6- A G1 C 1003 CHIP CAP. 0.001uF 500V W5R CF316W5R102K500AT K22271802 1- B a1 C 1004 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B f1 C 1005 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A B1 C 1005 AL.ELECTRO.CAP. 3300uF 16V RE3-16V332M 3300UF K40129065 18- A B1 C 1006 CHIP CAP. 7pF 200V CH GRM40CH070D200PT K22230213 1-5 B a1 C 1006 CHIP CAP. 8pF 200V CH GRM40CH080D200PT K22230214 VERSION A 6- B a1 C 1006 CHIP CAP. 7pF 200V CH GRM40CH070D200PT K22230213 VERSION C 6- B a1 C 1007 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B a2 C 1008 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A A1 C 1009 CHIP CAP. 33pF 200V CH GRM40CH330J200PT K22230222 1-5 B b1 C 1009 CHIP CAP. 39pF 200V CH GRM40CH390J200PT K22230223 VERSION A 6- B b1 C 1009 CHIP CAP. 33pF 200V CH GRM40CH330J200PT K22230222 VERSION C 6- B b1 C 1010 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1011 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1012 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A H2 C 1013 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b2 C 1014 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1015 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A G3 C 1016 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1017 CHIP CAP. 2pF 200V CH GRM40CH020C200PT K22230206 VERSION A 6- B b1 C 1018 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B a3 C 1019 CHIP CAP. 18pF 200V CH GRM40CH180J200PT K22230219 1-5 B b1 C 1019 CHIP CAP. 33pF 200V CH GRM40CH330J200PT K22230222 VERSION A 6- B b1 C 1019 CHIP CAP. 18pF 200V CH GRM40CH180J200PT K22230219 VERSION C 6- B b1 C 1020 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1021 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B f2 C 1022 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 1-5 B b1 C 1022 CHIP CAP. 10pF 50V CH GRM39CH100C50PT K22174248 VERSION A 6- B b1 C 1022 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 VERSION C 6- B b1 C 1023 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- B g1 C 1024 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b1 C 1025 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B a2 C 1026 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B g1 C 1027 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A G3 C 1029 AL.ELECTRO.CAP. 10uF 16V RC2-16V100M(4X7) K40129012 1- A G2 C 1030 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B a2 C 1031 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B f2 C 1032 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b1 C 1033 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B a2 C 1034 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b2 C 1035 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A B3 C 1036 CHIP CAP. 33pF 200V CH GRM40CH330J200PT K22230222 1-5 A F1 C 1036 CHIP CAP. 22pF 200V CH GRM40CH220J200PT K22230220 VERSION A 6- A F1 C 1036 CHIP CAP. 33pF 200V CH GRM40CH330J200PT K22230222 VERSION C 6- A F1 C 1037 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C3 C 1038 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1- B f2 C 1039 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 1- B b1 C 1040 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1-3 A B2 C 1041 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 1-5 A E1 C 1041 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 VERSION A 6- A E1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** MAIN UNIT *** PCB with Components CB0370001 TYPE C 1PCB with Components CB0370002 TYPE A 6Printed Circuit Board FR001570B 1Printed Circuit Board FR001570C 5Printed Circuit Board FR001570D 19-

LOT.SIDE.

LAY ADR.

Page 36

MAIN Unit

REF.

C 1041 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION C 6- A E1 C 1042 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- B b1 C 1044 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f2 C 1045 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 1- A E1 C 1046 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 1-5 A E1 C 1046 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 VERSION A 6- A E1 C 1046 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION C 6- A E1 C 1047 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B f2 C 1048 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B f2 C 1049 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1 A B2 C 1049 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 2- A B2 C 1050 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- B a2 C 1051 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 1- B b1 C 1052 CHIP CAP. 20pF 50V CH GRM39CH200J50PT K22174218 1-6 A E1 C 1052 CHIP CAP. 20pF 50V CH GRM39CH200J50PT K22174218 VERSION A 7- A E1 C 1052 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 VERSION C 7- A E1 C 1053 CHIP CAP. 18pF 200V CH GRM40CH180J200PT K22230219 1-5 A F2 C 1053 CHIP CAP. 15pF 200V CH GRM40CH150J200PT K22230218 VERSION A 6- A F2 C 1053 CHIP CAP. 18pF 200V CH GRM40CH180J200PT K22230219 VERSION C 6- A F2 C 1054 CHIP CAP. 30pF 50V CH GRM39CH300J50PT K22174222 1-5 A E1 C 1054 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION A 6 A E1 C 1054 CHIP CAP. 30pF 50V CH GRM39CH300J50PT K22174222 VERSION C 6 A E1 C 1054 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 7- A E1 C 1055 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- B a2 C 1056 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A E1 C 1057 CHIP CAP. 82pF 50V CH GRM39CH820J50PT K22174233 1-6 A E1 C 1057 CHIP CAP. 82pF 50V CH GRM39CH820J50PT K22174233 VERSION A 7- A E1 C 1057 CHIP CAP. 68pF 50V CH GRM39CH680J50PT K22174231 VERSION C 7- A E1 C 1058 CHIP CAP. 30pF 50V CH GRM39CH300J50PT K22174222 1-5 A E1 C 1058 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION A 6 A E1 C 1058 CHIP CAP. 30pF 50V CH GRM39CH300J50PT K22174222 VERSION C 6 A E1 C 1058 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 7- A E1 C 1059 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- B a1 C 1060 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A B2 C 1061 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B g2 C 1062 AL.ELECTRO.CAP. 10uF 16V ECEV1CS100SR K48120001 1- A F4 C 1063 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A E2 C 1065 CHIP CAP. 0.01uF 25V B GRM39B103K25PT K22144803 1-85 B f2 C 1066 CHIP CAP. 0.033uF 16V R GRM39R333K16PT K22124801 1- B f2 C 1067 CHIP CAP. 68pF 50V CH GRM39CH680J50PT K22174231 1- B f2 C 1067 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 43- B f2 C 1068 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A D1 C 1069 CHIP CAP. 20pF 50V CH GRM39CH200J50PT K22174218 1-6 A E1 C 1069 CHIP CAP. 20pF 50V CH GRM39CH200J50PT K22174218 VERSION A 7- A E1 C 1069 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 VERSION C 7- A E1 C 1070 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A F3 C 1071 CHIP CAP. 68pF 50V CH GRM39CH680J50PT K22174231 1- B f2 C 1071 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 43- B f2 C 1072 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 1- A E1 C 1073 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 1-5 A E1 C 1073 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION A 6- A E1 C 1073 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 VERSION C 6 A E1 C 1073 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 VERSION C 7- A E1 C 1074 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B f2 C 1075 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B g2 C 1076 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A D2 C 1078 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D2 C 1079 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A E1 C 1080 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A E3 C 1081 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A E1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 37

MAIN Unit

REF.

C 1082 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A D1 C 1083 AL.ELECTRO.CAP. 10uF 16V ECEV1CS100SR K48120001 1- A F4 C 1084 CHIP CAP. 470pF 50V CH GRM39CH471J50PT K22174249 1- A B1 C 1085 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D1 C 1086 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A E1 C 1087 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B g2 C 1089 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A C1 C 1091 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-5 A D1 C 1091 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION A 6- A D1 C 1091 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION C 6 A D1 C 1091 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION C 7- A D1 C 1092 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1-6 A D1 C 1092 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION A 7- A D1 C 1092 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION C 7- A D1 C 1093 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 1-5 A D1 C 1093 CHIP CAP. 39pF 50V CH GRM39CH390J50PT K22174225 VERSION A 6- A D1 C 1093 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 VERSION C 6- A D1 C 1094 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 1-5 A D1 C 1094 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 VERSION A 6- A D1 C 1094 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION C 6- A D1 C 1095 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f2 C 1096 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 1-5 A D1 C 1096 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION A 6- A D1 C 1096 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION C 6- A D1 C 1098 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b3 C 1099 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A D1 C 1100 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 1-5 A D1 C 1100 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION A 6- A D1 C 1100 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION C 6- A D1 C 1101 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 1-5 A D1 C 1101 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 VERSION A 6- A D1 C 1101 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 VERSION C 6- A D1 C 1103 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B f2 C 1104 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- A G2 C 1105 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 1-5 A D1 C 1105 CHIP CAP. 39pF 50V CH GRM39CH390J50PT K22174225 VERSION A 6- A D1 C 1105 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 VERSION C 6- A D1 C 1106 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 1-5 A D1 C 1106 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 VERSION A 6- A D1 C 1106 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION C 6- A D1 C 1107 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 1- A C2 C 1108 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A G2 C 1109 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-5 A D1 C 1109 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION A 6- A D1 C 1109 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION C 6 A D1 C 1109 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION C 7- A D1 C 1110 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1-6 A D1 C 1110 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION A 7- A D1 C 1110 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION C 7- A D1 C 1112 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A C2 C 1113 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- A C2 C 1114 CHIP CAP. 0.033uF 16V B ECJ1VB1C333K K22129515 1- A C2 C 1115 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 1- B d2 C 1116 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C2 C 1117 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e2 C 1118 CHIP CAP. 560pF 50V B GRM39B561M50PT K22174806 1- A B2 C 1119 CHIP CAP. 120pF 50V CH GRM39CH121J50PT K22174237 1- A C1 C 1120 CHIP CAP. 390pF 50V CH GRM39CH391J50PT K22174255 1- A B2 C 1121 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A D1 C 1122 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A D1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 38

MAIN Unit

REF.

C 1123 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A B2 C 1124 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 1- A D1 C 1125 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- A C2 C 1126 CHIP CAP. 560pF 50V B GRM39B561M50PT K22174806 1- A B2 C 1127 CHIP CAP. 12pF 50V CH GRM39CH120J50PT K22174213 1- B d2 C 1128 CHIP CAP. 0.015uF 25V B GRM39B153K25PT K22144805 1- A B3 C 1129 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A E2 C 1130 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A B2 C 1131 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f3 C 1132 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- A B3 C 1133 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A E2 C 1134 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 1 B e2 C 1134 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 2-5 B e2 C 1134 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 VERSION A 6- B e2 C 1134 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 VERSION C 6- B e2 C 1135 CHIP CAP. 82pF 50V CH GRM39CH820J50PT K22174233 1- A E2 C 1136 CHIP CAP. 0.022uF 25V B GRM39B223K25PT K22144807 1- A C2 C 1137 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D2 C 1138 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A D2 C 1139 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B d2 C 1140 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1141 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 1- B f2 C 1142 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C2 C 1143 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A E2 C 1144 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 1- B c3 C 1145 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1146 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1147 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B f2 C 1148 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B f2 C 1151 CHIP CAP. 0.033uF 16V R GRM39R333K16PT K22124801 1- B b2 C 1151 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 4- B b2 C 1151 CHIP CAP. 0.22uF 10V B GRM39B224K10PT K22104801 7- B b2 C 1153 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1154 CHIP CAP. 12pF 50V CH GRM39CH120J50PT K22174213 1- A D2 C 1155 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1156 CHIP CAP. 82pF 50V CH GRM39CH820J50PT K22174233 1- B b2 C 1157 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B b3 C 1158 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C2 C 1159 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B b2 C 1160 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b2 C 1161 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B b2 C 1162 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C3 C 1163 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A A2 C 1164 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- A C3 C 1165 AL.ELECTRO.CAP. 10uF 16V ECEV1CS100SR K48120001 1- A F2 C 1166 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A F2 C 1167 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B g2 C 1168 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b2 C 1169 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 1- A D2 C 1170 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D2 C 1171 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B g2 C 1172 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- A G2 C 1173 CHIP CAP. 0.0056uF 50V B ECJ1VB1H562K K22179623 1- A F2 C 1174 CHIP TA.CAP. 2.2uF 10V TESVA1A225M1-8R K78100021 1- A A2 C 1175 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B a2 C 1176 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 1- A G2 C 1177 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B a2 C 1178 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B a2 C 1179 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- A A2 C 1180 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 1- B d3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 39

MAIN Unit

REF.

C 1181 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B f3 C 1182 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f3 C 1183 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B f3 C 1184 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B f3 C 1185 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A B3 C 1186 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A B3 C 1187 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A C3 C 1188 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A C3 C 1189 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1- B d3 C 1190 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D4 C 1191 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B d2 C 1192 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 1- A D3 C 1193 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A D3 C 1194 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- B e3 C 1195 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- A D4 C 1196 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C3 C 1197 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- A D3 C 1198 CHIP CAP. 12pF 50V CH GRM39CH120J50PT K22174213 1- A D3 C 1199 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D3 C 1200 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D3 C 1201 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 1-5 B e3 C 1201 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 VERSION A 6- B e3 C 1201 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 VERSION A 26- B e3 C 1201 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 VERSION C 6- B e3 C 1201 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 VERSION C 26- B e3 C 1202 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1203 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 1- B g3 C 1204 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A C4 C 1205 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 1- A E3 C 1206 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 1-5 B e3 C 1206 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 VERSION A 6- B e3 C 1206 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 VERSION C 6- B e3 C 1207 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 1- B g3 C 1208 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A E3 C 1209 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B c3 C 1210 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B e3 C 1211 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 1-5 A C3 C 1211 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 VERSION A 6- A C3 C 1211 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 VERSION C 6- A C3 C 1212 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 1- B g3 C 1213 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1214 CHIP CAP. 56pF 50V CH GRM39CH560J50PT K22174229 1- A E3 C 1215 CHIP CAP. 56pF 50V CH GRM39CH560J50PT K22174229 1- A E3 C 1216 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1217 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- B c3 C 1218 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 1- A F3 C 1219 CHIP CAP. 12pF 50V CH GRM39CH120J50PT K22174213 1- A E3 C 1220 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1221 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A E3 C 1222 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B d3 C 1223 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1224 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B c3 C 1225 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A E3 C 1226 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B e3 C 1227 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 1- B e3 C 1228 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- B d3 C 1229 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B e3 C 1230 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A E3 C 1231 CHIP CAP. 0.01uF 25V B GRM39B103K25PT K22144803 1- B d3 C 1232 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 1- B c3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 40

MAIN Unit

REF.

C 1234 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A B3 C 1235 CHIP CAP. 0.033uF 16V R GRM39R333K16PT K22124801 1- B d3 C 1236 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B e3 C 1237 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- B f3 C 1238 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D3 C 1239 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- B c3 C 1240 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B d3 C 1241 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B c3 C 1242 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A D3 C 1243 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 1- A E3 C 1244 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A D3 C 1245 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A E3 C 1246 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A E3 C 1247 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C3 C 1248 AL.ELECTRO.CAP. 10uF 16V ECEV1CS100SR K48120001 1-18 A F3 C 1249 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 1- A C1 C 1250 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B f2 C 1250 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 5- B f2 C 1251 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B g2 C 1252 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- B b3 C 1254 CHIP CAP. 0.0027uF 50V B GRM39B272M50PT K22174814 1- B f2 C 1254 CHIP CAP. 0.0018uF 50V B GRM39B182M50PT K22174812 5- B f2 C 1255 CHIP CAP. 0.0033uF 50V B GRM39B332M50PT K22174815 1- B a2 C 1256 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A D2 C 1256 CHIP TA.CAP. 33uF 16V TEMSVC1C336M12R K78120033 19- A D2 C 1257 CHIP TA.CAP. 10uF 16V TEMSVB21C106M-8R K78120025 1- A D1 C 1258 CHIP CAP. 1uF 10V F GRM39F105Z10PT K22105001 5- B g2 C 1259 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION A 6 B b3 C 1259 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 7- B b3 C 1260 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 6- A G3 C 1261 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 VERSION A 6-18 C 1262 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 26- A C3 CD1001 CERAMIC DISC CDBM450C24T H7901060 1- A F2 CD1001 CERAMIC DISC CDBC450CX24-TC H7901340 19- A F2 CF1001 CERAMIC FILTER CFWM450G H3900435 1- A F3 CF1002 CERAMIC FILTER CFWM450E H3900466 1- A F3 CO1001 CERAMIC OSC 1MHz KBR-1000YTR17 H7900840 1- A B1 CO1001 CERAMIC OSC 1MHz KBR-1000YTR17 H7900840 19- A B1 CO1001 CERAMIC OSC 1MHz CSB1000J221T H7900550 40- A B1 D 1001 SURGE ABSORBER P6KE18 Q9000534 1- A B1 D 1001 SURGE ABSORBER P6KA18 Q9000721 7- A B1 D 1002 DIODE UM9957F/TR G2070562 1- B b1 D 1004 DIODE UM9957F/TR G2070562 1- A G1 D 1005 DIODE 1SS321 TE85R G2070076 1- B b1 D 1006 DIODE RLS135 TE-11 G2070128 1- A E1 D 1007 DIODE KV1470-TR00 G2070318 1- A E1 D 1007 DIODE KV1470-TL00 G2070680 6- A E1 D 1007 DIODE KV1470-TL00 G2070680 29- A E1 D 1007 DIODE KV1870STL G2070832 44- A E1 D 1008 DIODE KV1470-TR00 G2070318 1- A E1 D 1008 DIODE KV1470-TL00 G2070680 6- A E1 D 1008 DIODE KV1470-TL00 G2070680 29- A E1 D 1008 DIODE KV1870STL G2070832 44- A E1 D 1009 DIODE 1SS355 TE-17 G2070470 1- A E1 D 1010 DIODE 1SS355 TE-17 G2070470 1- B g2 D 1011 DIODE HVU350TRF G2070380 1- A D1 D 1012 DIODE HVU350TRF G2070380 1- A D1 D 1013 DIODE HVU350TRF G2070380 1- A D1 D 1014 DIODE HVU350TRF G2070380 1- A D1 D 1015 DIODE 1SS355 TE-17 G2070470 1- A G2

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 41

MAIN Unit

REF.

D 1016 DIODE DAP202U T106 G2070160 1- A B3 D 1017 DIODE MA143-(TX) G2070536 1- A E2 D 1018 DIODE 02CZ5.6Y TE85R G2070300 1- B b2 D 1019 DIODE MA142WK-(TX) G2070534 1- B b3 D 1021 DIODE 1SS355 TE-17 G2070470 1- B b3 D 1022 DIODE 1SS355 TE-17 G2070470 1- B b3 D 1023 DIODE D1F20-4063 G2070474 1- B g1 D 1024 DIODE 02CZ5.6Y TE85R G2070300 1 B g2 D 1024 DIODE HZM7C-TR G2070070 2- B g2 D 1024 DIODE HZM7.5NB2 TR G2070864 63- B g2 D 1025 DIODE 1SS355 TE-17 G2070470 1- B g2 D 1026 DIODE 1SS321 TE85R G2070076 1- B e2 D 1027 DIODE 1SS355 TE-17 G2070470 1- A A2 D 1028 DIODE MA729-(TX) G2070320 1- A A2 D 1029 DIODE 02CZ5.6Y TE85R G2070300 1- B d2 D 1030 DIODE 1SV230 TPH3 G2070126 1- B c3 D 1031 DIODE 1SS355 TE-17 G2070470 1- B g3 D 1032 DIODE HSU277TRF G2070118 1- A E3 D 1033 DIODE 1SS355 TE-17 G2070470 1- B e3 D 1034 DIODE 1SV230 TPH3 G2070126 1- B c3 D 1035 DIODE 1SV276(TPH3) G2070420 1- A D3 D 1036 DIODE 1SV276(TPH3) G2070420 1- A D3 D 1037 DIODE DAP202U T106 G2070160 1- A A3 D 1038 DIODE 1SV276(TPH3) G2070420 1- A D3 D 1039 DIODE 1SV276(TPH3) G2070420 1- A D3 D 1040 DIODE MA143-(TX) G2070536 1- B c3 D 1041 DIODE 1SV276(TPH3) G2070420 1- A E3 D 1042 DIODE 1SS270 G2090408 1- B f2 D 1042 DIODE 1SS355 TE-17 G2070470 5- B f2 D 1043 DIODE 1SS355 TE-17 G2070470 5- B g3 D 1044 DIODE 1SS270 G2090408 5- B e3 D 1044 DIODE 1SS355 TE-17 G2070470 19- B e3 F 1001 CHIP FUSE 0.25A F0805B0R25FWTR Q0000072 1- A A1 F 1001 CHIP FUSE 0.25A TF20N0.25TE Q0000100 26- A A1 FB1001 FERRITE BEADS SMB304729 L9190094 1- B f1 FB1002 FERRITE BEADS SMB304729 L9190094 1- B f1 FB1003 FERRITE BEADS SMB304729 L9190094 1- A E2 J 1001 CONNECTOR SB20-03WS P0090610 1- A G3 J 1002 CONNECTOR SB20-02WS P0090609 1- A G4 J 1003 CONNECTOR AE0031-00 P1090998 1- B g1 J 1004 CONNECTOR IL-Y-14P-S15T2-E P0090601 1- A A4 J 1005 CONNECTOR IL-Y-8P-S15T2-EF P0090646 1- A A2 J 1006 CONNECTOR B11B-ZR P0091200 1- A B4 J 1007 CONNECTOR IL-Y-12P-S15T2-EF P0091201 1- A B3 L 1001 COIL A1 3.5T3.5D0.8UEW R L0021647A 1- A G1 L 1002 COIL A1 3.5T3.5D0.8UEW R L0021647A 1- A G1 L 1004 COIL A1 3.5T3.5D0.8UEW R L0021647A 1- A F1 L 1005 CHIP COIL 0.22uH LER015TR22M L1690111 1- A F1 L 1006 COIL E2 0.35-1.6-7T-L L0022390 1- A E1 L 1007 COIL A1 3.5T3.5D0.8UEW R L0021647A 1- A F1 L 1008 M.RFC 0.0414uH 36CS 656LZ-08K=P3 L1690247 1-5 A E1 L 1008 M.RFC 0.0498uH 36CS 656LZ-09K=P3 L1690248 VERSION A 6- A E1 L 1008 M.RFC 0.0414uH 36CS 656LZ-08K=P3 L1690247 VERSION C 6- A E1 L 1009 M.RFC 2.2uH LAL04NA2R2M L1190319 1- A G2 L 1010 M.RFC 0.0414uH 36CS 656LZ-08K=P3 L1690247 1-5 A E1 L 1010 M.RFC 0.0498uH 36CS 656LZ-09K=P3 L1690248 VERSION A 6- A E1 L 1010 M.RFC 0.0414uH 36CS 656LZ-08K=P3 L1690247 VERSION C 6- A E1 L 1011 M.RFC 0.047uH HK1608 47NJ-T L1690524 1-5 L 1011 M.RFC 0.047uH HK1608 47NJ-T L1690524 VERSION C 6 L 1012 M.RFC 0.22uH LK1608 R22K-T L1690410 1- A E1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 42

MAIN Unit

REF.

L 1013 COIL E2 0.28-1.0-4.5T-R L0022395 1- A D1 L 1014 COIL E2 0.28-1.0-4.5T-R L0022395 1- A C1 L 1015 M.RFC 0.33uH LK1608 R33K-T L1690412 1-5 B e2 L 1015 M.RFC 0.39uH LK1608 R39K-T L1690413 VERSION A 6- B e2 L 1015 M.RFC 0.33uH LK1608 R33K-T L1690412 VERSION C 6- B e2 L 1016 M.RFC 0.27uH LK1608 R27K-T L1690411 1-5 A C1 L 1016 M.RFC 0.33uH LK1608 R33K-T L1690412 VERSION A 6- A C1 L 1016 M.RFC 0.27uH LK1608 R27K-T L1690411 VERSION C 6- A C1 L 1017 M.RFC 0.22uH LK1608 R22K-T L1690410 1- A C1 L 1018 M.RFC 0.33uH LK1608 R33K-T L1690412 1- A C1 L 1019 M.RFC 3.3uH LK1608 3R3K-T L1690686 1- A D1 L 1020 M.RFC 0.56uH LK1608 R56K-T L1690415 1- A E2 L 1021 CHIP COIL 0.084uH LQN1A84NJ04 L1690259 1 A D2 L 1021 CHIP COIL 0.084uH LQN1A84NJ04 L1690259 2- A D2 L 1024 M.RFC 0.22uH LK2125 R22K-T L1690311 1- A C2 L 1025 M.RFC 0.082uH HK2125 82NK-T L1690388 1- A C3 L 1026 M.RFC 0.068uH HK1608 68NJ-T L1690526 1- A D3 L 1027 M.RFC 0.082uH HK1608 82NJ-T L1690527 1- B e3 L 1028 M.RFC 0.056uH HK1608 56NJ-T L1690525 1- A D3 L 1029 M.RFC 10uH LK2125 100K-T L1690331 1- B g3 L 1030 M.RFC 0.082uH HK1608 82NJ-T L1690527 1- A C3 L 1031 COIL E2 0.35-1.6-8T-L L0022458 1-5 A E3 L 1031 COIL E2 0.3-1.7-8T-L L0022376 VERSION A 6- A E3 L 1031 COIL E2 0.35-1.6-8T-L L0022458 VERSION C 6- A E3 L 1032 COIL E2 0.28-1.0-6T-R L0022366 1-5 A E3 L 1032 COIL E2 0.28-1.0-7TR L0022422 VERSION A 6- A E3 L 1032 COIL E2 0.28-1.0-6T-R L0022366 VERSION C 6- A E3 L 1033 M.RFC 10uH LK2125 100K-T L1690331 1- A D3 Q 1001 IC MM1216ENRE G1092432 1- B b2 Q 1002 TRANSISTOR 2SB1201S-TL G3070195 1- A G3 Q 1003 IC TDA2003H G1090815 1- A H3 Q 1004 TRANSISTOR IMH6A T108 G3070066 1- B a2 Q 1005 TRANSISTOR DTB123YK T146 G3070156 1- B a2 Q 1005 TRANSISTOR DTB113ZK T146 G3070103 4- B a2 Q 1006 TRANSISTOR DTB123EK T146 G3070022 1- B a2 Q 1007 IC NJM2902V-TE1 G1091679 1- A B2 Q 1008 TRANSISTOR DTC323TK T146 G3070042 1- B g2 Q 1009 IC MX165BDW-TR G1092175 1- A B2 Q 1009 IC MX165CDW-TR G1092775 6- A B2 Q 1010 IC HA17805P G1090936 1- A F4 Q 1010 IC KIA7805API G1093163 76- A F4 Q 1011 IC M67741H-01 G1091622 1-5 B e1 Q 1011 IC M67741L-01 G1091623 VERSION A 6- B e1 Q 1011 IC M67741H-01 G1091622 VERSION C 6- B e1 Q 1012 TRANSISTOR 2SC4226-T2B R24 G3342267D 1- A E1 Q 1014 TRANSISTOR 2SB1143S G3211430S 1- A F2 Q 1015 TRANSISTOR 2SC4116GR TE85R G3341167G 1- A F3 Q 1016 IC NJM2902V-TE1 G1091679 1- A B2 Q 1017 IC NJM2904V-TE1 G1091677 1- A G2 Q 1020 TRANSISTOR DTC124EU T106 G3070045 1- B f3 Q 1021 FET SGM2016M-T7 G4070005 1- A D1 Q 1021 FET SGM2016AM-T7 G4070012 8- A D1 Q 1022 TRANSISTOR IMZ1 T108 G3070025 1- A H2 Q 1025 TRANSISTOR IMH6A T108 G3070066 1- B f3 Q 1026 TRANSISTOR 2SC4215Y TE85R G3342157Y 1- A E2 Q 1028 TRANSISTOR 2SC3357-T2 G3333577 1- B e2 Q 1029 IC BA4116FV-E2 G1092616 1- A F2 Q 1029 IC TA31136FN(EL) G1091605 7- A F2 Q 1030 IC AN8005M-(E1) G1091454 1- B g2 Q 1031 TRANSISTOR 2SC3357-T2 G3333577 1- A D3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.

SIDE.

LAY ADR.

Page 43

MAIN Unit

REF.

Q 1032 TRANSISTOR 2SA1586Y TE85R G3115867Y 1- B b2 Q 1033 TRANSISTOR DTC124EU T106 G3070045 1- B f2 Q 1034 TRANSISTOR 2SA1586Y TE85R G3115867Y 1- B g2 Q 1035 TRANSISTOR IMH6A T108 G3070066 1- A G2 Q 1036 IC RH5VL45AA-T1 G1090966 1- A A2 Q 1036 IC RH5VT45AA-T1 G1093215 19- A A2 Q 1036 IC RH5VL45AA-T1 G1090966 22- A A2 Q 1038 TRANSISTOR 2SC5107-O(TE85R) G3351077O 1- B d3 Q 1039 IC MB89P677APFM ø 1 A A3 Q 1039 IC Q 1039 IC Q 1039 IC Q 1039 IC MB89P677APFM DST:NTL 53- A A3 Q 1039 IC Q 1039 IC Q 1039 IC Q 1040 TRANSISTOR 2SC4116GR TE85R G3341167G 1- B d2 Q 1041 TRANSISTOR 2SC5107-O(TE85R) G3351077O 1- B e3 Q 1042 TRANSISTOR 2SC4116GR TE85R G3341167G 1- A D4 Q 1043 FET 2SK880GR TE85R G3808807G 1- A D3 Q 1044 TRANSISTOR 2SC5107-O(TE85R) G3351077O 1- A D3 Q 1045 TRANSISTOR 2SC4116GR TE85R G3341167G 1- B g3 Q 1046 TRANSISTOR 2SC5107-O(TE85R) G3351077O 1- A E3 Q 1047 TRANSISTOR 2SC4116GR TE85R G3341167G 1- B c3 Q 1048 TRANSISTOR DTC124EU T106 G3070045 1 A E3 Q 1048 TRANSISTOR 2SC4116GR TE85R G3341167G 2- A E3 Q 1049 IC BR93LC66RF-E2 G1092006 1- B g3 Q 1049 IC BR93L66RF-WE2 G1093912 85- B g3 Q 1050 IC SC370651FR2 G1091937 1- A D3 Q 1050 IC MC145192FR2 G1092017 26- A D3 Q 1050 IC MC145193FR2 G1093424 41- A D3 Q 1051 TRANSISTOR DTC124EU T106 G3070045 1- B g3 Q 1052 TRANSISTOR IMH6A T108 G3070066 1- B f3 Q 1053 TRANSISTOR DTC124EU T106 G3070045 1- A C3 Q 1054 TRANSISTOR 2SC4116GR TE85R G3341167G 26- A C3 R 1001 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B a1 R 1002 CHIP RES. 4.7 1W 5% RMC1 4R7JTE J24305479 1- B a3 R 1003 CHIP RES. 4.7 1W 5% RMC1 4R7JTE J24305479 1- B a3 R 1004 CHIP RES. 1 1/10W 5% RMC1/10T 1R0J J24205010 1- B a3 R 1005 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B g1 R 1006 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- B g1 R 1007 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- B g1 R 1008 CHIP RES. 270 1/10W 5% RMC1/10T 271J J24205271 1- B a2 R 1009 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g1 R 1010 CHIP RES. 560 1/16W 5% RMC1/16 561JATP J24185561 1- B f2 R 1011 CHIP RES. 2.7 1/16W 5% RMC1/16 2R7JATP J24185279 1-3 B a2 R 1013 CHIP RES. 2.7 1/16W 5% RMC1/16 2R7JATP J24185279 4- A G2 R 1014 CHIP RES. 470 1/4W 5% RMC1/4 471JATP J24245471 1- B b1 R 1015 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 1- B f2 R 1016 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 1- A C3 R 1017 CHIP RES. 1.5M 1/16W 5% RMC1/16 155JATP J24185155 1- B f2 R 1018 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- B b1 R 1019 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 1-3 A B2 R 1020 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e3 R 1021 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B a1 R 1022 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B a1 R 1023 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B f2 R 1024 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B f2 R 1025 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- B b2 R 1026 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A E1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

MB89677ARPFM-G-161-BND MB89677ARPFM-G-163-BND MB89677ARPFM-G-181-BND

MB89677ARPFM-G-181-BND MB89677ARPFM-G-181-BND MB89677ARPFM-G-181-BND

ø 2- A A3 ø 6- A A3

ø EXPORT 53- A A3 ø STANDARD 53- A A3 ø VTX(USA) 53- A A3

LOT.SIDE.

15-52

A A3

LAY ADR.

* Please contact VERTEX STANDARD.

Page 44

MAIN Unit

REF.

R 1027 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 1- A B2 R 1028 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- A B2 R 1029 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 1- B g2 R 1030 CHIP RES. 150 1W 5% RMC1 151JTE J24305151 1- B a1 R 1031 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B g2 R 1032 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A E1 R 1033 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 1- A B2 R 1034 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- B f2 R 1035 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 1- A E1 R 1036 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 1- A E1 R 1037 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 1- A E1 R 1038 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 1- A B1 R 1039 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 1- B g2 R 1039 CHIP RES. 560k 1/16W 5% RMC1/16 564JATP J24185564 86- B g2 R 1042 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- B g2 R 1042 CHIP RES. 680k 1/16W 5% RMC1/16 684JATP J24185684 86- B g2 R 1043 CHIP RES. 330 1/10W 5% RMC1/10T 331J J24205331 1 B e2 R 1043 CHIP RES. 470 1/10W 5% RMC1/10T 471J J24205471 2-5 B e2 R 1043 CHIP RES. 180 1/10W 5% RMC1/10T 181J J24205181 VERSION A 6- B e2 R 1043 CHIP RES. 470 1/10W 5% RMC1/10T 471J J24205471 VERSION C 6- B e2 R 1044 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- A E1 R 1045 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- A E1 R 1046 CHIP RES. 33 1/10W 5% RMC1/10T 330J J24205330 1 B e2 R 1046 CHIP RES. 22 1/10W 5% RMC1/10T 220J J24205220 2-5 B e2 R 1046 CHIP RES. 56 1/10W 5% RMC1/10T 560J J24205560 VERSION A 6- B e2 R 1046 CHIP RES. 22 1/10W 5% RMC1/10T 220J J24205220 VERSION C 6- B e2 R 1047 CHIP RES. 33 1/10W 5% RMC1/10T 330J J24205330 1 B e2 R 1047 CHIP RES. 22 1/10W 5% RMC1/10T 220J J24205220 2-5 B e2 R 1047 CHIP RES. 56 1/10W 5% RMC1/10T 560J J24205560 VERSION A 6- B e2 R 1047 CHIP RES. 22 1/10W 5% RMC1/10T 220J J24205220 VERSION C 6- B e2 R 1048 CHIP RES. 560 1/16W 5% RMC1/16 561JATP J24185561 1- A E1 R 1049 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B1 R 1050 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- A C2 R 1052 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e2 R 1053 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1054 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1055 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B c3 R 1056 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- A F3 R 1057 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- B c3 R 1058 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1059 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A G2 R 1060 CHIP RES. 180k 1/16W 5% RMC1/16 184JATP J24185184 1- B f2 R 1062 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1063 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 1- A C2 R 1064 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1065 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1066 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A C2 R 1067 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A C2 R 1068 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- A G2 R 1069 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1 A C2 R 1069 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 2- A C2 R 1070 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- A C2 R 1071 CHIP RES. 3.9k 1/16W 5% RMC1/16 392JATP J24185392 1- B a1 R 1072 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- B e2 R 1072 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 5- B e2 R 1073 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 1- A C1 R 1074 CHIP RES. 180k 1/16W 5% RMC1/16 184JATP J24185184 1- A C1 R 1075 CHIP RES. 150k 1/16W 5% RMC1/16 154JATP J24185154 1- A B2 R 1076 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A G2 R 1077 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 1- B a1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 45

MAIN Unit

REF.

R 1078 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 1- A B2 R 1079 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- A C1 R 1080 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A B2 R 1081 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 1- A C1 R 1082 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- A D1 R 1083 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- B a2 R 1085 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- A C1 R 1086 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A C2 R 1087 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- A D1 R 1088 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B f3 R 1089 CHIP RES. 2.7k 1/16W 5% RMC1/16 272JATP J24185272 1- A D1 R 1090 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 1- A B2 R 1091 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- A D1 R 1092 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 1- A D1 R 1093 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A C2 R 1094 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B2 R 1095 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A G2 R 1096 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A H2 R 1097 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- B a2 R 1098 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- B a2 R 1099 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B f3 R 1100 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A H2 R 1101 CHIP RES. 2.7k 1/16W 5% RMC1/16 272JATP J24185272 1- A H2 R 1102 CHIP RES. 1.2k 1/16W 5% RMC1/16 122JATP J24185122 1- A E2 R 1103 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- A B3 R 1104 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- A E2 R 1105 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A B3 R 1106 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1-4 R 1107 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B d2 R 1108 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B3 R 1109 CHIP RES. 330 1/10W 5% RMC1/10T 331J J24205331 1 B e2 R 1109 CHIP RES. 470 1/10W 5% RMC1/10T 471J J24205471 2-5 B e2 R 1109 CHIP RES. 180 1/10W 5% RMC1/10T 181J J24205181 VERSION A 6- B e2 R 1109 CHIP RES. 470 1/10W 5% RMC1/10T 471J J24205471 VERSION C 6- B e2 R 1110 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A E2 R 1111 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 1- A C3 R 1112 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1-4 R 1113 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B f3 R 1114 CHIP RES. 39k 1/16W 5% RMC1/16 393JATP J24185393 1- A C3 R 1115 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 1- B f2 R 1115 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 86- B f2 R 1116 CHIP RES. 390k 1/16W 5% RMC1/16 394JATP J24185394 1- B f2 R 1117 CHIP RES. 680k 1/16W 5% RMC1/16 684JATP J24185684 1- B f2 R 1118 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B2 R 1119 CHIP RES. 180 1/10W 5% RMC1/10T 181J J24205181 R 1120 CHIP RES. 22 1/10W 5% RMC1/10T 220J J24205220 1 A D2 R 1120 CHIP RES. 0 1/10W 5% RMC1/10T 000J J24205000 2- A D2 R 1121 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1122 CHIP RES. 150k 1/16W 5% RMC1/16 154JATP J24185154 1- B f2 R 1123 CHIP RES. 22 1/10W 5% RMC1/10T 220J J24205220 1 A C2 R 1123 CHIP RES. 10 1/10W 5% RMC1/10T 100J J24205100 2- A C2 R 1124 CHIP RES. 270 1/16W 5% RMC1/16 271JATP J24185271 1- B b2 R 1125 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1126 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1128 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1-18 R 1129 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B f2 R 1130 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 1- B f2 R 1131 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B f2 R 1132 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e2 R 1133 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

41-42

A D2

LAY ADR.

Page 46

MAIN Unit

REF.

R 1134 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1135 CHIP RES. 1.8M 1/16W 5% RMC1/16 185JATP J24185185 1- B b2 R 1135 CHIP RES. 3.3M 1/16W 5% RMC1/16 335JATP J24185335 5- B b2 R 1136 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B b2 R 1137 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1138 CHIP RES. 820 1/16W 5% RMC1/16 821JATP J24185821 1- B b2 R 1138 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 7- B b2 R 1139 CHIP RES. 680k 1/16W 5% RMC1/16 684JATP J24185684 1- B b2 R 1139 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 7- B b2 R 1140 CHIP RES. 47 1/10W 5% RMC1/10T 470J J24205470 1- B e3 R 1141 CHIP RES. 1.5k 1/16W 5% RMC1/16 152JATP J24185152 1- B b2 R 1142 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- A C3 R 1143 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- B b2 R 1144 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A D3 R 1145 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A F2 R 1146 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- B b2 R 1147 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B b2 R 1148 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B b2 R 1149 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A A3 R 1150 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1151 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- A F2 R 1151 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 7- A F2 R 1152 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A A3 R 1153 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B b2 R 1154 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B g2 R 1155 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1157 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A F2 R 1158 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f3 R 1159 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- A D2 R 1160 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f3 R 1161 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1162 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A G2 R 1163 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1164 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B g2 R 1165 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1166 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A A2 R 1167 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1168 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 1- A G2 R 1169 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1170 CHIP RES. 270k 1/16W 5% RMC1/16 274JATP J24185274 1- A G2 R 1171 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 1- B a2 R 1172 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b2 R 1173 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B f3 R 1174 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B d2 R 1175 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B a2 R 1176 CHIP RES. 1.5M 1/16W 5% RMC1/16 155JATP J24185155 1- A G2 R 1177 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A A2 R 1178 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B d3 R 1179 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f2 R 1180 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 1- B d3 R 1181 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B d2 R 1182 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 1-5 A D3 R 1182 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 VERSION A 6- A D3 R 1182 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 VERSION A 26- A D3 R 1182 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 VERSION C 6- A D3 R 1183 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B f3 R 1184 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 1- A D3 R 1185 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1 A D3 R 1185 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 2- A D3 R 1186 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 47

MAIN Unit

REF.

R 1187 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f4 R 1188 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- B e3 R 1188 CHIP RES. 68k 1/16W 5% RMC1/16 683JATP J24185683 43- B e3 R 1189 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f3 R 1190 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A D3 R 1190 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 19- A D3 R 1191 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- B f3 R 1192 CHIP RES. 27 1/10W 5% RMC1/10T 270J J24205270 1- B f3 R 1193 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A C3 R 1194 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- A C3 R 1195 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- B e3 R 1196 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- B f3 R 1197 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- A D3 R 1198 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B c3 R 1199 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 1- B g3 R 1200 CHIP RES. 68k 1/16W 5% RMC1/16 683JATP J24185683 1- A D3 R 1201 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- B c3 R 1202 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- A B3 R 1203 CHIP RES. 10 1/16W 5% RMC1/16 100JATP J24185100 1-25 B d3 R 1204 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- B c3 R 1205 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B3 R 1206 CHIP RES. 1 1W 5% RMC1 1R0JTE J24305010 1- B b4 R 1207 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B c3 R 1208 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A B3 R 1209 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- A B3 R 1210 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- A D3 R 1211 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- A E3 R 1212 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B g3 R 1213 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 1- A D3 R 1214 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B e3 R 1215 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- B e3 R 1215 CHIP RES. 2.7k 1/16W 5% RMC1/16 272JATP J24185272 41- B e3 R 1216 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 1- A E3 R 1217 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A E3 R 1218 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1219 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- B e3 R 1220 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A B3 R 1221 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1222 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1223 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1224 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A E3 R 1225 CHIP RES. 5.6k 1/16W 5% RMC1/16 562JATP J24185562 1- B g3 R 1226 CHIP RES. 820 1/16W 5% RMC1/16 821JATP J24185821 1-5 B d3 R 1226 CHIP RES. 1.2k 1/16W 5% RMC1/16 122JATP J24185122 VERSION A 6- B d3 R 1226 CHIP RES. 820 1/16W 5% RMC1/16 821JATP J24185821 VERSION C 6- B d3 R 1227 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B d3 R 1228 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B e3 R 1229 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A E3 R 1230 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- B g3 R 1231 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 1- B d3 R 1232 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- B d3 R 1233 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e3 R 1234 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B e3 R 1235 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e3 R 1236 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1237 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- A D3 R 1238 CHIP RES. 390 1/16W 5% RMC1/16 391JATP J24185391 1- A D3 R 1238 CHIP RES. 270 1/16W 5% RMC1/16 271JATP J24185271 3- A D3 R 1238 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 5- A D3 R 1239 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A A3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT.SIDE.

LAY ADR.

Page 48

MAIN Unit

REF.

R 1240 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A C3 R 1241 CHIP RES. 270k 1/16W 5% RMC1/16 274JATP J24185274 1- B c3 R 1242 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- B c3 R 1243 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B e3 R 1244 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- A D3 R 1245 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- A E3 R 1246 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B c3 R 1246 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 4- B c3 R 1247 CHIP RES. 56k 1/16W 5% RMC1/16 563JATP J24185563 1- B c3 R 1247 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 4- B c3 R 1248 CHIP RES. 5.6k 1/16W 5% RMC1/16 562JATP J24185562 1- B d3 R 1249 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A C2 R 1250 CHIP RES. 330k 1/16W 5% RMC1/16 334JATP J24185334 1-5 A E3 R 1250 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 VERSION A 6- A E3 R 1250 CHIP RES. 330k 1/16W 5% RMC1/16 334JATP J24185334 VERSION C 6- A E3 R 1251 CHIP RES. 82k 1/16W 5% RMC1/16 823JATP J24185823 1-5 A E3 R 1251 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 VERSION A 6- A E3 R 1251 CHIP RES. 82k 1/16W 5% RMC1/16 823JATP J24185823 VERSION C 6- A E3 R 1253 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A C1 R 1254 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- B e3 R 1255 CARBON FILM RES. 3.3k 1/6W 5% RD16PJ332 3.3K J01225332 1- B f2 R 1255 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 5- B f2 R 1256 CHIP RES. 0 1/8W 5% RMC1/8T 000J J24215000 1- A D2 R 1257 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1-1 B g3 R 1257 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 5- B g3 R 1258 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 VERSION A 6 A E1 R 1258 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 7- A E1 R 1259 CHIP RES. 270 1/16W 5% RMC1/16 271JATP J24185271 26- A C3 R 1260 CHIP RES. 680 1/10W 5% RMC1/10T 681J J24205681 26- A C3 R 1261 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 41- A E3 R 1262 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 41- A D3 R 1263 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 86T 1001 COIL 05RF 100MHz 100M M5-N1 R12-S804Y L0022492 1- A D1 T 1002 COIL 05RF 100MHz 100M M5-N1 R12-S804Y L0022492 1- A C1 TC1001 TRIMMER CAP. 20pF ECR-KN020E61X K91000213 1- A E3 TH1001 THERMISTOR TBPS1R104K475H5Q G9090069 1- B a1 TH1003 THERMISTOR TBPS1R103K440H5Q G9090067 1- B c2 TH1004 THERMISTOR TBPS1R103K440H5Q G9090067 1- B c2 VR1001 POT. 10k EVN-5ESX50B14 J51811103 1- A C2 VR1002 POT. 50k EVN-5ESX50B54 J51811503 1- A G2 VR1003 POT. 10k EVN-5ESX50B14 J51811103 1- A G2 VR1004 POT. 50k EVN-5ESX50B54 J51811503 1- A B2 VR1005 POT. 50k EVN-5ESX50B54 J51811503 1- A B3 VR1006 POT. 10k EVN-5ESX50B14 J51811103 1- A G2 X 1001 XTAL LP-3.5.2S 9.8304MHz 9.8304MHZ H0103148 1- A A3 X 1002 XTAL CA-301M 17.25MHz 17.25MHZ H0103107 1- A F3 XF1001 XTAL FILTER 17T12B5 H1102273 1- A D2 XF1002 XTAL FILTER 17T12B5 H1102273 1- A D2

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

SHIELD CASE RA0060200 1-

LOT.SIDE.

LAY ADR.

Page 49

Circuit Diagram

Display-1 Unit

Page 50

Display-1 Unit

Parts Layout

Side A

BU4094BCFV (Q2002)

XN1213 (9L) (Q2001, 2003, 2004)

DTC124EK (25) (Q2005)

Side B

Page 51

Parts List

Display-1 Unit

REF.

D 2001 LED HLMP-1540 G2090696 1- A D 2002 LED HLMP-1540 G2090696 1- A D 2003 LED HLMP-1540 G2090696 1- A D 2004 LED HLMP-1540 G2090696 1- A D 2005 LED HLMP-1440 G2090695 1- A D 2006 LED HLMP-1540 G2090696 1- A D 2007 LED TLS123 G2090703 1- A D 2008 DIODE 1SS355 TE-17 G2070470 1- B D 2009 DIODE 1SS355 TE-17 G2070470 1- B JP2001 WIRE ASSY A0953+ T9206686 1Q 2001 TRANSISTOR XN1213-(TX) G3070194 1- B Q 2002 IC BU4094BCFV-E1 G1092128 1- B Q 2002 IC BU4094BCFV-E2 G1093527 58- B Q 2003 TRANSISTOR XN1213-(TX) G3070194 1- B Q 2004 TRANSISTOR XN1213-(TX) G3070194 1- B Q 2005 TRANSISTOR DTC124EK T146 G3070034 1- B R 2001 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 2002 CHIP RES. 10k 1/10W 5% RMC1/10T 103J J24205103 1- B R 2003 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 2004 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 2005 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 2006 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 2007 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 2008 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 2009 CHIP RES. 10k 1/10W 5% RMC1/10T 103J J24205103 1- B

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** DISPLAY-1 UNIT *** PCB with Components CB0382001 Printed Circuit Board FR001580B

LOT.SIDE.

LAY ADR.

Page 52

Display-1 Unit

Note:

Page 53

Circuit Diagram

Display-2 Unit

Page 54

Display-2 Unit

16153211817411

1013128657

D2E2F2G2Dig.1

Dig.2

Parts Layout

Side A

DN8657S (Q3001)

XN1213 (9L) (Q3002)

DTC124EK (25) (Q3003)

9 1

D.P1D.P2

C2 E2

B2 F2

10 18

C1 E1

B1 F1

Side B

A1 B1 C1 D1 E1 F1 G1 A2 B2 C2

DS3001 7-Segment LCD Display

Page 55

Parts List

Display-2 Unit

REF.

D 3002 DIODE 1SS355 TE-17 G2070470 1- B D 3003 LED TLY211 G2090637 1- A D 3004 DIODE 1SS355 TE-17 G2070470 1- B D 3005 DIODE 1SS355 TE-17 G2070470 1- B D 3006 LED TLG211 G2090343 1- A D 3007 DIODE 1SS355 TE-17 G2070470 1- B D 3008 LED TLS211 G2090704 1- A DS3001 LED GL7S201J G2090488 1- A JP3001 WIRE ASSY A0953+ T9206687 1Q 3001 IC DN8657S-T1 G1092688 1- B Q 3002 TRANSISTOR XN1213-(TX) G3070194 1- B Q 3003 TRANSISTOR DTC124EK T146 G3070034 1- B R 3001 CHIP RES. 680 1/10W 5% RMC1/10T 681J J24205681 1- B R 3002 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 3003 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 3004 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- B R 3005 CHIP RES. 10k 1/10W 5% RMC1/10T 103J J24205103 1- B

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** DISPLAY-2 UNIT *** PCB with Components CB0383001 Printed Circuit Board FR001590B

LOT.SIDE.

LAY ADR.

Page 56

Display-2 Unit

Note:

Page 57

Circuit Diagram

VR Unit

Parts Layout

Side A Side B

Parts List

REF. DESCRIPTION

PCB with Components CB0384001 Printed Circuit Board FR001600B

VR4001 POT. RK0971111 10KB/SW J60800228 1-

VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** VR UNIT ***

LOT.SIDE.

LAY ADR.

Page 58

MIC Unit

Circuit Diagram

Parts Layout

Side A Side B

Parts List

REF. DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** MIC UNIT *** PCB with Components CB0384001 Printed Circuit Board FR001600B

J 5001 CONNECTOR R41-2509H P1090714 1JP5001 WIRE ASSY A0953+ T9206688 1-

LOT.SIDE.

LAY ADR.

Page 59

E095390

No portion of this manual

may be reproduced

VERTEX STANDARD CO., LTD.

without the ermission of

VERTEX STANDARD CO., LTD.

Vertex VX-2000V Service manual

Introduction

Contents

Operating Manual Reprint

CONTROLS & CONNECTORS

REAR (Heatsink)

OPERATION

USER PROGRAMMABLE CHANNEL SELECTIONS

OPTIONAL ACCESSORIES

J1003 DSUB 9-Pin Data Connector Pin Assignment

Specifications

General

Receiver

Transmitter

Exploded View & Miscellaneous Parts

VX-2000V 4ch Front Panel Block Diagram

Block Diagram

VX-2000V 40ch Front Panel Block Diagram

VX-2000V Main Unit Block Diagram

VX-2000V 4ch Front Interconnection Diagram

Interconnection Diagram

VX-2000V 40ch Front Interconnection Diagram

Circuit Description

Receive Signal Path

Squelch Control

Transmit Signal Path

Automatic Transmitter Power Control

Transmit Inhibit

Spurious Suppression

PLL Frequency Synthesizer

Push-To-Talk (PTT) Transmit Activation

Alignment

Required Test Equipment

Alignment Preparation & Precautions

PLL Reference Frequency

Transmitter Deviation

Transmitter Output Power

Receiver Squelch Threshold

Restore Original Channel Data

Side A

Side B

Side A

Side B

Side A

Side B

Parts List

Circuit Diagram

Display-1 Unit

Parts Layout

Side A

Side B

Parts List

Circuit Diagram

Display-2 Unit

Parts Layout

Side A

Side B

Parts List

Circuit Diagram

VR Unit

Parts Layout

Side A Side B

Parts List

MIC Unit

Circuit Diagram

Parts Layout

Side A Side B

Parts List