Vertex VX-2000U Service manual

Download

Page 1

UHF Land Mobile Transceiver

VX-2000U

Service Manual

VERTEX STANDARD CO., LTD.

4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

VERTEX STANDARD

US Headquarters

10900 Walker Street, Cypress, CA 90630, U.S.A.

International Division

8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.

YAESU EUROPE B.V.

P.O. Box 75525, 1118 ZN Schiphol, The Netherlands

YAESU UK LTD.

Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K.

VERTEX STANDARD HK LTD.

Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong

40 channel version 4 channel version

Introduction

This manual provides technical information necessary for servicing the VX-2000U UHF Land Mobile transceiver.

The VX-2000U is carefully designed to allow the knowledgeable operator to make nearly all adjustments required for various station conditions, modes and operator preferences simply from the controls on the panels, without opening the case of the transceiver. The VX-2000U Operating Manual describes these adjustments, plus certain internal settings.

Servicing this equipment requires expertise in handling surface mount chip components. Attempts by non-qualified persons to service this equipment may result in permanent damage not covered by warranty.

For the major circuit boards, each side of the board is identified by the type of the majority of components installed on that side.

In most cases one side has only chip components, and the other has either a mixture of both chip and lead components (trimmers, coils, electrolytic capacitors, packaged ICs, etc.), or lead components only.

While we believe the technical information in this manual is correct, Vertex Standard assumes no liability for damage that may occur as a result of typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies in the technical information would be appreciated. Vertex Standard reserves the right to make changes in this transceiver and the alignment procedures, in the interest of technological improvement, without notification of the owners.

Operating Manual Reprint............................ 2

Specifications ................................................... 7

Exploded View & Miscellaneous Parts....... 8

Block Diagram ................................................. 9

Interconnection Diagram............................. 13

Circuit Description ...................................... 15

Alignment....................................................... 19

Board Unit (

MAIN Unit ............................................................... 23

DISPLAY-1 Unit ...................................................... 55

DISPLAY-2 Unit ...................................................... 59

VR Unit ..................................................................... 63

MIC Unit .................................................................. 64

Schematics, Layouts & Parts

)

Page 2

Operating Manual Reprint

CONTROLS & CONNECTORS

40 channel version4 channel version

Microphone Jack

Connect the microphone plug to this jack.

MONI Button & Indicator

This button selects the “squelch” (receiver mute) mode. When the yellow indicator is off, “tone” or “coded” squelch is active. When the indicator glows steadily, only “noise squelch” is active, and any signal present on the channel will be heard. When the indicator is blinking, the squelch is disabled, and background noise will be heard if no signal is present.

A Button & Indicator

This button is provided for an ACCESSORY function such as HIGH/LOW POWER selection, “TALK-AROUND”, or “CALL ALERT” functions. The green “A” indicator will be illumi- nated when this function is active.

VOLUME and POWER ON/OFF Knob

This knob adjusts the receiver volume, and turns the radio off when turned all the way to the left into the click-stop.

TX/BUSY Indicator Lamp

This lamp blinks red when the channel is busy, and glows steadily red during transmission. Do not transmit when this

indicator is blinking, as a courtesy to other users of the chan- nel.

The following item is unique to the 4-channel radio versions:

CHANNEL Numbered Indicators & Button

Press the CHANNEL button to select the operating chan- nel; the channel number currently in use will light up on the display panel.

The following items are unique to the 40-channel radio versions:

CHANNEL Selector Buttons (p) and (q)

Push one of these keys to select the operating channel, as shown on the display.

Numeric Channel Display

This display area shows the channel number and priority- channel/scan status.

SEL/PRI Button

This button is used to select a channel for “Priority” moni- toring, and is used together with the SCAN button to select the desired scanning mode.

SCAN Button

This button is used to activate scanning, to select or remove channels on the scanning list, and (together with the SEL/

PRI button) to select scanning mode.

P Indicator

This small dot indicates Priority Channel status (described later).

E Indicator

This small dot indicates Scanning on/off status (described later).

Page 3

REAR (Heatsink)

13.6V DC Cable Pigtail w/Connector

The supplied DC power cable must be affixed to this 2-pin connector.

Antenna Socket

The 50-ohm coaxial feedline to the antenna must be con- nected here, using a “UHF” type (PL-259) plug.

Operating Manual Reprint

External Speaker Jack

An external loudspeaker may be connected to this 2-con- tact, 3.5-mm miniature phone jack.

DSUB 9-Pin Data Connector

External Transmit Audio input, PTT (Push To Talk), Squelch, and Receive Audio output signals may be obtained from this connector for use with accessories such as a data transmission/reception modem, etc.

Page 4

Operating Manual Reprint

OPERATION

Power ON/OFF

Turn the VOLUME/POWER knob clockwise to turn on the ra- dio. The active display and channel indicators will become illu- minated, indicating the status of the radio. The channel indicated will be the same one on which you were operating when the ra- dio was last turned off.

Setting the Channel

In 4-channel versions, press the CHANNEL button to change channels. In 40-channel versions, the display will show either a channel number or a Scan Mode indicator (Sc, Ur, SP or UP). If a Scan Mode indicator is displayed, press the SCAN button momen- tarily so that a channel number is displayed; then press either the UP (p) or DOWN (q) button to change channels.

Setting the Volume

Rotate the VOLUME/POWER knob clockwise to increase the volume level. If no signal is present on which to adjust the vol- ume level, push and hold in the MONI button for two seconds; the yellow “MONI” indicator will blink, and either background noise or a voice signal will be heard. You may now adjust the VOLUME/POWER knob for a comfortable listening level. When you are done, press the MONI button momentarily to re- turn to silent monitoring.

Transmitting

To transmit, wait until the “TX/BUSY” indicator is off (this in- dicates that the channel is not in use). Then press the PTT (Push- To-Talk) switch on the side of the microphone; while holding in the PTT switch, speak in a normal voice level across the face of the microphone. During transmission, the red “TX/BUSY” indi- cator will glow steadily. When you are done transmitting, re- lease the PTT switch; the VX-2000 will revert to the “receive” mode.

The remaining instructions apply to 40-channel trans-

Scanning

To activate scanning on your radio, first place the microphone in its hanger. Now press the SCAN button momentarily. The radio will scan in one of four available Scan Modes (detailed below), and will halt when a signal is received which contains the correct code to open your squelch. Scanning will resume automatically either after a preset interval of a few seconds, or after the other station stops transmitting (depending on how your radio was pro- grammed).

The four Scan Modes, and their corresponding displays, are:

Display Scanning function

Sc Scan all channels

Ur Scan only user-selected channels

SP Monitor one channel plus dealer-designated Priority Channel(s)

UP Scan user-selected channels plus uer-designated Priority Channel(s)

The user-selected channels for the Ur and UP Scan Modes are ones you can set up yourself, as described at the right. The “Priority” channels are those on which signals will take prior- ity over signals received on other channels; that is, if a signal appears on a Priority Channel while another appears on a non- priority channel, the Priority Channel signal will be heard, and not the other. Up to two of the installed channels may be designated by your Dealer as pre-programmed Priority Channels for the SP mode (the radio will not indicate which they are), and you can addi- tionally program any two channels as “User Priorities” for the UP mode. In the SP mode, the non-priority channel will be the last one displayed. When a Scan Mode is displayed, you can select another by press- ing the SEL/PRI button repeatedly (the display will cycle through the above selections). Note that the radio will not scan if the microphone is not in its hanger.

ceiver versions only

Special Transmitter Functions

If your VX-2000 is programmed for Busy Channel Lock- Out, the transmitter will not activate when the PTT switch is

pressed unless the “TX/BUSY” indicator is off (so as to pre- vent interference to other users of the same channel). If the selected channel has been programmed for Automatic Time-Out, you must limit the length of your transmissions. While transmitting with this feature activated, a “beep” will sound ten seconds before the timer expires, and then another “beep” sound as the timer expires: the “TX/BUSY” indica- tor will shut off, and transmission will cease. Release the PTT switch, listen for a moment, then press PTT again to resume transmission. This feature prevents interference to other users caused by a microphone which accidentally is stuck in the “transmit” position (wedged between seats of a car, etc.).

Page 5

Operating Manual Reprint

USER PROGRAMMABLE CHANNEL SELECTIONS

You can program a list of channels to be scanned, and up to two channels to be monitored on a “priority” basis. Your selections will be maintained in memory until you change or delete them.

Setting of these channels involves two small “Dot” indicators at the top of the channel display field. The Dot to the left of the first digit is the “P” (Priority) indicator, while the Dot to the left of the second digit is the “E” (Enable for Scanning) indicator.

To create or modify the Scan and Priority selections, first turn the radio off. Now press and hold in the SCAN button while you turn the transceiver back on; continue to hold the SCAN button in for two seconds after the radio has come on, then you may release it. Now press the UP (p) or DOWN (q) button repeatedly, and note whether or not the “E” (right dot) or “P” (left) dots appear on any of your channels. If a dot appears by any channel, it means that it has been designated as either a Scan-Enabled or Priority channel, respectively. To enable or disable a channel from the User Scan list, press the SEL/PRI button momentarily. The “E” dot will appear or dis- appear, as appropriate. To change the Priority Channels, first cancel both by selecting either, and then pressing the SEL/PRI button momentarily. Now select the channel you wish to designate as the 1st Priority Chan-

nel, and hold in the SEL/PRI button for 2 seconds, until a beep sounds and the “P” indicator blinks. If you wish to designate a 2nd Priority Channel, move to that channel, and again hold in the SEL/PRI button for 2 seconds; this time, the “P” indicator will glow, but will not blink. If you have deleted a channel from Priority status, you must re- enable it for scanning if you want it to be included on your Scan List. Press the SEL/PRI button momentarily to do this.

Coded Squelch - the MONI Button

Your transceiver may be programmed so that when the mi- crophone is removed from its hanger, coded squelch is de- feated, and you can hear any signal on the channel (the yel- low “MONI” indicator will be lit). You can get the same result, without lifting the microphone, by pressing the MONI button momentarily. To avoid listening to unnecessary chat- ter, keep the microphone in its hanger, and press the MONI button when necessary to turn the yellow indicator off (un- less you want to listen to other calls on the channel). Holding the MONI button in for two seconds defeats both the coded squelch and noise squelch, so background noise can be heard (the “MONI” indicator will blink in this case). Press the MONI button momentarily to return the yellow indicator to its previous state (either off or steadily on).

OPTIONAL ACCESSORIES

CE-20 Programming Software (for IBM PC/compatibles only)

VPL-1 Programming Cable

T9101411 Radio-to-Radio Cloning Connection Cable

FP-1025A Heavy-Duty (20A) AC Power Supply

MD-11A8J Desktop Microphone

MH-600D DTMF Back-lit Microphone w/Autodial

MLS-100 External Loudspeaker

LF-1 DC Line Filter

VTM-20 VX-Trunk II Trunking Mobile Logic Board

F2D-4A/B 2-Tone Decoder Unit

FTE-18 ANI Unit

Page 6

Operating Manual Reprint

J1003 DSUB 9-Pin Data Connector Pin Assignment

ÃÄ Â Á À

È Ç Æ Å

À SQ: Squelch Signal Output

Carrier In: Active High (5 V / 47 kΩ)

Á RX_AUD_OUT: Received Audio Output (Two choices available)

Á-1 De-Empasized Audio Output: 100 mV / 10 kΩ

This output level's default state is fixed at the factory by

having no jumper at JP1003 and soldering the jumper at

JP1002 on the MAIN Unit.

Á-2 Flat / Unmuted Audio Output: 250 mV / 10 kΩ

(Unsolder the jumper at JP1002 and solder a jumper at JP1003 on the MAIN Unit to activate Á-2)

Â EXT_MIC: External MIC Audio Input (Two choices available)

Â-1 Pre-Emphasized / IDC / Splatter Filtered Audio Input:

2.5 mV / 600 Ω

This input is fixed at the factory by attaching capacitor

C1254 across JP1005 and soldering a jumper at JP1004

on the MAIN Unit.

Â-2 Flat (Non-Pre-Emphasized) Audio Input: 650 mV / 10 kΩ

(Remove the jumper at JP1004 and solder a jumper across JP1005 on the MAIN Unit to activate Â-2)

Ã Not Used

Ä GND: Ground

Å A_OUTPUT: Accessory Output (Two choices available)

Å-1 Not Used

This is the default setting at the factory (no jumper across

JP1001 on the MAIN Unit).

Å-2 Accessory Output: Open Collector Output

"A" Lamp ON: Low, "A" Lamp OFF: Open

Maximum voltage: 13.8 V, Maximum sink current 5 mA

(Solder a jumper at JP1001 on the MAIN Unit to acti- vate Å-2)

Æ PTT: External PTT Signal input

GND: TX, Open: RX

Ç 5 V

Switched and regulated DC 5 V output for supplying

power to an accessory.

Maximum output current is 50 mA.

È Not Used

Page 7

Specifications

General

Frequency Range (version): 400 ~ 430, 450 ~ 480 or 480 ~ 512 MHz (UHF vers. A/D/F, respectively)

No. of Channels & Spacing: 4 or 40 channels 25-kHz, 12.5-kHz spacing

Modes of Emission: 16K0F3E ,11K0F3E

Frequency Stability: ±0.00025%

Antenna Requirements: 50 ohms, unbalanced (SO-239 socket)

Voltage Requirements: 11.8 V to 15.6 V DC, negative ground

Current Consumption (approx.): 250 mA Stby, 200 mA Rx, 6.5 A Tx

Operating Temperature Range: -22 °F to +140 °F (-30 °C to +60 °C)

Size (WHD, approx.): 6¼ ´ 1½ ´ 4¼ inches (160 ´ 40 ´ 105 mm)

Weight (approx.): 1.9 lbs. (0.85 kg)

Receiver

Receiver Circuit Type: Double-Conversion Superheterodyne

Intermediate Frequencies: 43.95 MHz , and 450 kHz (all models)

Sensitivity: 0.2/0.25 µV for 12-dB SINAD

0.3/0.35 µV for 20 dB NQ

Hum & Noise Ratio: Better than 45 dB for 25-kHz/step,

Better than 40 dB for 12.5-kHz/step

Adjacent Channel Selectivity: >70 dB for 25-kHz/step,

>60 dB for 12.5-kHz/step

Intermodulation Distortion: Better than 65 dB

Spurious Rejection: Better than 65 dB

External Audio Output Power: 2 watts into 8 ohms with <10% THD

Transmitter

Power Output: 25/5 watts (high/low, programmable)

Modulation Type/Deviation: Frequency Modulation, ±5 kHz (±2.5 kHz )

Hum & Noise Ratio: Better than 45 dB for 25-kHz/step,

Better than 40 dB for 12.5-kHz/step

Modulation Distortion: Less than 5%

Spurious Emissions: Better than 65 dB (below carrier)

Microphone Impedance: 600 ohms

Specifications are subject to change without notice or obligation.

Page 8

Exploded View & Miscellaneous Parts

VXSTD P/NREF.

U24208001 TAPTITE SCREW M2.6X8 (Lot. 1~3) 1

U20208001 BINDING HEAD SCREW M2.6X8 (Lot. 4~) 1

U20306002 BINDING HEAD SCREW M3X6NI 4

U23205001 TAPTITE SCREW M2.6X5 4

U23206001 TAPTITE SCREW M2.6X6 3

U24306002 TAPTITE SCREW M3X6NI 5

U31206007 OVAL HEAD SCREW M2.6X6B 7

U24308001 TAPTITE SCREW M3X8 1

RA0034900 RUBBER KNOB (4CHANNEL)

CP6003001 PANEL-SUB A ASSY

Description

DISPLAY-1 Unit

MAIN Unit

Qty.

P1090654 CONNECTOR

VXSTD P/N

Q0000062 Q0000008 (Lot. 8~) T9021810 DC CABLE 1

RA0060100 CASE

Description

FUSE 10A 2

T9206675 WIRE ASSY

P1090984 CONNECTOR

Qty.

RA0015600 RUBBER KNOB (40 CHANNEL)

R6054387B SPECIAL NUT

RA001330A KNOB

VR Unit

MIC Unit

NAME PLATE RA0013900 (EXPORT) RA0014000 (VTX(USA))

M4090122 SPEAKER

CP6007001 PANEL-SUB B ASSY

RA0056000 RA005600A (Lot. 3) RA005600B (Lot. 4~)

DISPLAY-2 Unit

RA00560AB (THA1: Lot. 33~) RA00560AC (THA: Lot. 47~) RA005600C (Lot. 47~) CHASSIS

Non-designated parts are available only as part of a designated assembly.

Page 9

VX-2000U 4ch Front Panel Block Diagram

Block Diagram

VX-2000U 40ch Front Panel Block Diagram

Page 10

Block Diagram

Note:

Page 11

VX-2000U Main Unit Block Diagram

Block Diagram

Page 12

Block Diagram

Note:

Page 13

VX-2000U 4ch Front Interconnection Diagram

Interconnection Diagram

(T9206689A: Lot 6~)

Page 14

Interconnection Diagram

VX-2000U 40ch Front Interconnection Diagram

(T9206689A: Lot 6~)

Page 15

Circuit Description

Receive Signal Path

Incoming RF from the antenna jack is delivered

to the MAIN Unit, and passes through a low-pass

filter consisting of coils L1001, L1002, L1004, and

L1006, capacitors C1002, C1006, C1009, C1017,

C1019, C1022, C1041, and C1046, and antenna

switching diodes D1002 (UM9957F) and D1005

(RLS135), then passed to the receiver front end.

Signals within the frequency range of the trans-

ceiver then enter a varactor-tuned band-pass fil-

ter consisting of coils L1008, L1010, L1011, L1013,

L1014, L1015, L1016, L1017, L1018, L1019, L1020,

L1023, and L1024, capacitors C1045, C1052, C1054,

C1056, C1058, C1068, C1072, C1073, C1086, C1090,

C1091, C1093, C1094, C1095, C1097, C1100, C1101,

C1105, C1106, C1110, and C1111, plus diodes

D1007, D1008, D1011, D1012, D1013, and D1014

(all HVU350). After bandpass filtering, the in-

band RF signals are amplified by RF preamplifi-

er Q1012 (2SC4227).

Buffered output from the VCO is amplified by

Q1038 (2SC5107) to provide a pure 1st local sig-

nal between 406.05 and 436.05 MHz for injection

to the 1st mixer Q1021 (SGM2016). The result-

nal within Q1029. The 2nd IF then passes through

the ceramic filter CF1001 (CFWM450G) or

CF1002 (CFWM450E) to strip away unwanted

mixer products, and then is applied to the limit-

er amplifier in Q1029, which removes amplitude

variations in the 450 kHz IF. Speech detection by

the ceramic discriminator CD1001

(CDBM450C24T) is then performed, converting

the second IF into an audio signal.

Detected audio from Q1029 is amplified by

Q1017-1 (NJM2904V) and then applied to the de-

emphasis network, consisting of capacitors

C1084/C1089, resistors R1038/R1049, and Q1007-

4 (NJM2902V). The de-emphasized audio sig-

nal is then applied to CTCSS subsystem IC Q1009

(MX165BDW), which contains the TX/RX audio

filter, CTCSS decoder, and CTCSS encoder; if a

CTCSS tone is present on the incoming signal, it

is removed by the high-pass filter in Q1009. The

processed signal passes through the audio mute

gate Q1008 (DTC124EK) and the volume con-

trol, then enters the audio power amplifier Q1003

(TDA2003H), which provides up to 2 Watts to

the external speaker jack or internal speaker.

ing 43.95 MHz 1st IF then passes through mono-

lithic crystal filter XF1001, which strips away all

but the desired signal, and the signal is then

amplified by Q1026 (2SC4215Y). The amplified

1st IF signal is then applied to FM IF subsystem

IC Q1029 (BA4116FV), which contains the 2nd

mixer, 2nd local oscillator, a limiter amplifier, and

a noise amplifier.

A 2nd local signal is generated by PLL refer-

ence/2nd local oscillator Q1046 (2SC4116GR),

using the 14.5 MHz crystal X1002 in a 3rd-over-

tone mode as a reference. This signal is mixed

with the 43.95 MHz IF at Q1029 to produce the

450 kHz 2nd IF when mixed with the 1st IF sig-

Squelch Control

The squelch circuitry consists of a noise amplifi-

er, band-pass filter, and noise detector within Q1029,

plus control circuitry within Q1039 (MB89677).

When no carrier is received, noise at the out-

put of the detector stage in Q1029 is amplified,

band-pass filtered and detected by Q1029. The

resulting DC squelch control voltage is passed

to pin 33 of microprocessor Q1039. When no car-

rier is being received, pin 33 of Q1039 remains

low, signaling pin 5 of Q1039 to keep the green

"BUSY" LED off, and simultaneously signaling pin

19 of Q1039 to command AF mute gate Q1008

(DTC124EK) to block receiver audio.

Page 16

Circuit Description

When a carrier appears at the discriminator,

noise is removed from the output, causing pin

33 of Q1039 to go high, in turn causing the "BUSY"

LED and audio output lines to turn on. The mi-

croprocessor then checks for CTCSS information.

If CTCSS decode is not activated, or if CTCSS

decode is activated and a signal carrying a match-

ing tone is received, the microprocessor allows

audio to pass through AF mute gate Q1008 and

audio amplifier Q1003 to the speaker.

Transmit Signal Path

Speech input from the microphone is delivered

to the MAIN Unit, where it passes through the pre-

emphasis network (R1016 and C1031). The pre-

emphasized speech signal proceeds through the

AF high-pass filter at Q1009, then is applied to

the IDC (Instantaneous Deviation Control) at

Q1016-3 (NJM2902V), with deviation level being

set by potentiometer VR1001. The audio then pass-

es to a splatter filter in sections 1 and 4 of Q1016,

which filters out high-frequency components

which could result in over-deviation.

The processed audio is mixed with the CTC-

SS tone (if activated) generated by CTCSS sub-

system IC Q1009, then delivered to D1031

(1SV230) for frequency modulation of the PLL

carrier (at the transmitting frequency) up to ±5

kHz from the unmodulated carrier frequency.

Automatic Transmitter Power Control

RF output from the final amplifier is sampled

by C1039 and C1051 and rectified by D1006

(1SS321). The resulting DC voltage is fed through

Automatic Power Controller Q1014 (2SB1143S),

Q1015 (2SC4116GR), and Q1017-2 to effect con-

trol of the gain of transmitter PA Q1011. The mi-

croprocessor, Q1039, issues commands for setting

"HIGH" or "LOW" power output.

Transmit Inhibit

When the transmit PLL is unlocked, pin 2 of

PLL IC Q1049 (SC370651F) goes to logic "low"

level. The resulting DC unlock control voltage

switches off the TX inhibit switch Q1022 (1MZ1),

which interrupts the supply voltage to the trans-

mitter PA, Q1011, thus disabling the transmitter.

Spurious Suppression

Generation of spurious products by the trans-

mitter is minimized by the fundamental carrier

frequency being equal to the final transmitting

frequency, modulated directly in the transmit

VCO. Additional harmonic suppression is pro-

vided by a low-pass filter consisting of L1001,

L1002, L1007, C1002, C1006, C1009, C1017,

C1019, C1036, and C1053, resulting in more than

60 dB of harmonic suppression prior to delivery

of the RF signal to the antenna jack.

The modulated signal from the VCO, Q1047

(2SC5107), is buffered by Q1038 and Q1044 (both

2SC5107). The low-level transmit signal is then

amplified by Q1028 and Q1031 (both 2SC3357),

then applied to the final amplifier, Q1101

(M57729H), providing 25 Watts of transmitter

power. The transmit signal then passes through

the antenna switch, D1003 (MI407), and low-pass

filter (which suppresses harmonic spurious radi-

ation) before delivery to the antenna jack.

PLL Frequency Synthesizer

The Phase-Locked Loop (PLL) circuitry on the

MAIN Unit includes VCO Q1047, VCO buffer

Q1044, and PLL subsystem IC Q1049, which in-

cludes a reference divider, serial-to-parallel data

latch, programmable divider, phase comparator,

and charge pump.

Stability of the reference oscillator is main-

tained by a regulated 5 Volt supply, which in-

cludes Q1001 (MM1216EN), Q1002

Page 17

Circuit Description

(2SB1201STP-FA), Q1040 (2SC4116GR), and

D1029 (02CZ5.6Y), with temperature compen-

sation provided by thermistors TH1003/TH1004

and capacitors associated with the 14.5 MHz ref-

erence crystal, X1002.

In the receive mode, VCO Q1047 oscillates

between 406.05 and 436.05 MHz, according to the

transceiver version and the programmed receiv-

ing frequency. The VCO output is buffered by

Q1044, and applied to the prescaler section of

Q1049. There the VCO signal is divided by 64 or

65, according to a control signal from the data

latch section of Q1049, before being applied to

the programmable divider section of Q1049. The

data latch section of Q1049 also receives serial

dividing data from the microprocessor, Q1039,

which causes the pre-divided VCO signal to be

ference between the signals derived from the

VCO and the crystal reference oscillator. The

VCO is thus phase-locked to the crystal reference

oscillator. The output of the VCO is then deliv-

ered to the first mixer via buffer amplifier Q1044.

For transmission, the VCO Q1047 oscillates

between 450 and 480 MHz, according to the mod-

el version and the programmed transmit frequen-

cy. The remainder of the PLL circuitry is shared

with the receiver section. However, the dividing

data from the microprocessor is such that the

VCO frequency is at the actual transmitting fre-

quency (rather than being offset by the IF, as in

the receiving case). Also, the VCO is modulated

by the speech audio applied to D1031 (1SV230),

as described previously.

Receive and transmit buses select which VCO

further divided in the programmable divider sec-

tion, depending on the desired receive frequen-

cy, so as to produce either a 10 kHz or 12.5 kHz

derivative of the current VCO frequency.

Meanwhile, the reference divider section of

Q1049 divides the 14.5 MHz crystal reference fre-

quency by 1450 (or 1160) to produce the 10 kHz

(or 12.5 kHz) loop reference (respectively). The 10

kHz (or 12.5 kHz) signal from the programmable

divider (derived from the VCO) and that derived

from the reference oscillator are applied to the

phase detector section of Q1049, which produces

a pulsed output with pulse duration depending

on the phase difference between these input sig-

nals. The pulse train is filtered to DC and returned

to varactors D1038 and D1039 (both 1SV276).

Changes in the level of the DC voltage applied

is made active via Q1050 (DTC124EU). FET

Q1043 (2SK880GR) buffers the VCV line for ap-

plication to the tracking bandpass filters in the

receiver front end.

Push-To-Talk (PTT) Transmit Activation

The PTT switch on the microphone is connect-

ed to pin 24 of microprocessor Q1039, so that

when the PTT switch is closed, pin 35 of Q1039

goes low. This signals the microprocessor to ac-

tivate the TX/RX controller Q1004 (IMH6), which

then disables the receiver by interrupting the 9

V supply bus at Q1006 (DTB123YK) to the re-

ceiver front-end, FM IF subsystem IC, and receiv-

er VCO circuitry. At the same time, Q1005

(DTB123YK) activates the transmit 9 V supply

line to enable the transmitter.

to the varactors affect the reactance in the tank

circuit of the VCO, changing the oscillating fre-

quency of the VCO according to the phase dif-

Page 18

Circuit Description

Channel Selection & Display

(4-channel version)

The CHANNEL button on the front panel causes

microprocessor Q1039 to select the operating fre-

quency and CTCSS frequency data from serial

EEPROM Q1048 (BR93LC66AF). The operating

frequency data is in the form of PLL dividing

ratios, which are passed to the PLL IC on the

MAIN Unit via strobe, data, and clock outputs on

pins 43, 42, and 41 respectively. The channel digit

display data from the microprocessor is strobed

by pin 46 to display latch Q2002 (BU4094BCFV)

on the DISPLAY-1 Unit, which decodes the data

and drives the four channel LEDs and the func-

tion indicator LEDs.

Channel Selection & Display

(40-channel version)

The UP and DOWN buttons on the front panel

cause microprocessor Q1039 to select the oper-

ating frequency and CTCSS frequency data from

serial EEPROM Q1048. The operating frequency

data is in the form of PLL dividing ratios, which

are passed to the PLL IC on the MAIN Unit via

strobe, data, and clock outputs on pins 43, 42,

and 41 respectively. The channel digit display

data from the microprocessor is strobed by pin

46 to display latch Q3001 (DN8657S) on the DIS-

PLAY-2 Unit, which decodes the data and drives

the two 7-segment LEDs and the function indi-

cator LEDs.

Page 19

Alignment

The VX-2000 is carefully aligned at the facto-

ry for the specified performance across the de-

signed frequency range. Realignment should,

therefore, not be necessary except in the event of

a component failure, or when altering the fre-

quency range (“version”).

The following procedures cover the sometimes-

critical and tedious adjustments that are not nor-

mally required once the transceiver has left the

factory. However, if damage has occurred and

some parts subsequently are replaced, alignment

may be required in order to restore the original

alignment. If a sudden problem occurs during oth-

erwise normal operation, it is likely due to part

failure, and realignment should be performed only

after the faulty component has been replaced.

All component replacement and service

should be performed only by an authorized

Vertex representative, or the warranty policy

may be voided. Vertex service technicians are ex-

perienced with the circuitry, and are fully

equipped for part replacement and alignment.

When any repairs are completed, Vertex service

technicians perform comprehensive performance

checks to ensure that total transceiver system per-

formance complies with each and every specifi-

cation for this product.

Those who undertake any of the following

alignment procedures are cautioned to proceed

at their own risk. Problems caused by unautho-

rized attempts at realignment are not covered by

the warranty policy covering this transceiver.

Also, Vertex reserves the right to change circuits

and alignment procedures, in the interest of im-

proved performance, without notifying owners.

Under no circumstances should any alignment

be attempted unless the normal function and op-

any/all faulty components replaced, and realign-

ment determined to be absolutely necessary.

Required Test Equipment

The following test equipment (and thorough

familiarity with its correct use) is necessary for

complete realignment. Correction of problems

caused by misalignment resulting from the use

of improper test equipment is not covered by our

warranty policy.

While most steps do not require all the test

equipment listed, the interactions of some adjust-

ments may require that more complex adjust-

ments be performed afterwards. Do not, there-

fore, attempt to perform only a single step un-

less it is clearly isolated electrically from all oth-

er steps. Have all test equipment ready before

beginning, and follow all of the steps in a section

in the order presented.

r RF Signal Generator with calibrated output to

550 MHz

r Deviation Meter (linear detector)

r In-line Wattmeter with 5% accuracy at 550 MHz

r 50-W Dummy Load with a power rating of 50

W at 550 MHz

r Regulated DC Power Supply, adjustable from

10 V to 17 V DC at 10 A

r Frequency Counter with 0.2 ppm accuracy at

550 MHz

r AF Signal Generator

r DC Voltmeter, high impedance

r SINAD Meter

r IBM PC

Windows® v3.1 (or later) installed

r Vertex VPL-1 Connection Cable and CE-20

Channel Programming Diskette

r UHF Sampling Coupler

/compatible computer with Microsoft

eration of the radio are fully understood, the cause

of the malfunction has been clearly pinpointed and

Page 20

Alignment

Alignment Preparation & Precautions

Before beginning align"ment, connect the trans-

ceiver to the PC using the VPL-1 Connection Ca-

ble, and upload the current frequency data from

the customer’s radio to the computer; save this

information to disk so that it can be downloaded

to the radio again after alignment is completed.

Next, refer to the label at the rear of the bot-

50 W

Dummy Load

In-Line

Wattmeter

Deviation

meter

Frequency

Counter

RF Sampling

Coupler

CT-71 Connection cable

COM Port

RF Signal Generator

Transceiver

Generator

Power Supply

13.8 V

tom cover of the radio to determine its “version”

(frequency range); using the CE-20 software, pro-

gram the four “Test” simplex channels shown in

the table below, as appropriate for the radio ver-

sion you are working with:

Channel

1 2 3 4

Version “A”

400.000 MHz

415.000 MHz

430.000 MHz

Version “D”

450.000 MHz

465.000 MHz

480.000 MHz

Version “D”

450.000 MHz

465.000 MHz

480.000 MHz

Download this data to the transceiver under test.

Note: When alignment is finished, you may wish to

save these alignment channels as a disk file for

future service work. Make certain to re-load the

original channel data (uploaded from the radio

prior to servicing) into the transceiver, and com-

plete a final performance check, before return-

ing the equipment to the customer.

A 50-W dummy load and in-line wattmeter

must be connected to the rear-panel antenna jack

in all procedures which require transmission.

Correct alignment is not possible without a re-

Alignment Setup

After completing one alignment step, read the

following step to determine whether or not the

same test equipment will be required. If not, re-

move the test equipment (except dummy load

and wattmeter) before proceeding.

Correct alignment requires that the ambient

temperature be the same as that of the transceiv-

er, and that this temperature be held constant

between 68°F and 86°F (20°C and 30°C). When

the transceiver is brought into the shop from hot

or cold air, it should be allowed time to come to

room temperature before alignment is attempt-

ed. All test equipment should similarly be thor-

oughly warmed up.

Whenever possible, alignments should be per-

formed with oscillator shields and circuit boards

firmly affixed in place.

Note: Signal levels in dB referred to in these align-

ment procedures are based on 0 dBµ = 0.5 µV

(closed circuit).

sistive 50-W termination for the transmitter.

Be certain that your power supply delivers

13.8 VDC, as measured directly at the radio's DC

input plug, during transmitter tests. Any volt-

age drop in the cable, or due to the loading on

the power supply, must be compensated to 13.8

VDC for accurate alignment.

Connect the test equipment as shown in the

pictorial above.

Page 21

Alignment

PLL VCV (Varactor Control Voltage)

Performance Check

r Connect the DC voltmeter between test point

TP1033 on the MAIN Unit and chassis ground.

r Set the transceiver to channel 3, and confirm

that the reading is about 4.5V (for Ver. A and

F) or 4.3V (for Ver. D).

r Now select channel 1, and confirm that the

reading changes to about 0.9V.

r Again select channel 3. Key the transmitter,

and confirm that the voltmeter reading is ap-

proximately 4.5V (for Ver. A and F) or 4.3V

(for Ver. D).

r Once more select channel 1 and again key the

transmitter. Confirm that the voltmeter read-

ing is approximately 1.0V.

Transmitter Output Power

r Preset trimmer potentiometer VR1002 (MAIN

Unit) fully clockwise.

r Select (Band center) channel 2. Key the trans-

mitter, and confirm that at least 30 Watts of

power output is measured. Now select chan-

nels 1 and 3, and confirm that 30 Watts of RF

power is present on the band edge channels.

r Using the computer, re-program channel 1 for

“LOW” power output, and download this

data to the transceiver.

r Select channel 2, and adjust (“HIGH” power)

potentiometer VR1002 for 25 Watts of RF power.

r Select channel 1, and adjust “LOW” power) po-

tentiometer VR1003 for 5 Watts of RF power.

Transmitter Deviation

PLL Reference Frequency

r With the wattmeter, dummy load, and fre-

quency counter connected to the antenna jack,

select channel 2.

r Key the transmitter, and adjust TC1001 on the

MAIN Unit, if necessary, so that the counter fre-

quency is within 200 Hz of 415.000.00 MHz for

Ver. A, 465.000.00 MHz for Ver. D or 496.000.00

MHz for Ver. F.

VR1001

r Select channel 2, and adjust the AF genera-

tor’s attenuator so as to deliver 50 mV output

at 1 kHz to the microphone jack.

r Key the transmitter, and adjust VR1001 (MAIN

Unit) for ±4.3 kHz deviation as measured on

the deviation meter (tolerance: 100 Hz).

r On the computer, re-program channel 2 to en-

able a 100 Hz CTCSS (encode) tone, and down-

load this data to the transceiver.

VR1006 VR1002

VR1004 VR1005 TP1033 TC1001

MAIN Unit Alignment Points

VR1003

Page 22

Alignment

r Reduce the AF generator’s output to zero. Key

the transmitter, and adjust VR1004 (MAIN

Unit) for ±800 Hz deviation on the CTCSS tone

(within 100 Hz).

r On the computer, re-program channel 2 to en-

able DCS code 627 (encode), and download

this data to the transceiver.

r With the AF generator still set to zero, key the

transmitter, and adjust VR1005 (MAIN Unit)

for ±900 Hz deviation on the DCS signal (with-

in 100 Hz).

Receiver Squelch Threshold

r Set the transceiver to channel 2. Set the RF sig-

nal generator to the same frequency (415.000

for version A, 465.000 MHz for version D,

496.000 MHz for Ver. D). Set the signal gener-

ator’s output to -7 dBµ.

r Adjust VR1006 (MAIN Unit) clockwise until

the squelch just closes, and then counterclock-

wise until the squelch just opens.

r Turn off the signal generator, and confirm that

the squelch again closes when the RF input

signal disappears.

Restore Original Channel Data

r When all alignment steps have been complet-

ed, re-load the original channel data from your

computer’s disk, and download it to the trans-

ceiver.

Page 23

Circuit Diagram

13.6 (13.5) 0 (8.0)

0 (1.1)

13.3 (11.8)

0 (3.4)

0 (4.7)

2.7 (4.0)

3.3 (4.0)

0 (8.6)

0 (0.8)

0 (5.9)

0 (7.3)

MAIN Unit (Lot. 1~)

7.8 (7.8)

7.3 (7.3)

7.4 (7.4)

3.5 (3.5)

13.6 (12.7)

0.1 (0.3)

8.4 V

0 (0)

8.6 V

6.3 (6.6)

p-p

13.6 (12.7)

4.7 (0.5)

9.0 (9.0)

9.0 (0.1)

0.1 (8.2)

5.0 (0)

13.5 (13.5)

5.0 (5.0)

1.3 (1.0)

9.0 (9.0)

4.0 (4.0)

0 (8.8)

0.8 (0.8)

4.0 (4.0)

p-p

2.0 (2.0)

0 (2.4)

2.0 (1.8)

0 (1.1)

1.7 V

4.0 (4.0)

p-p

4.7 (4.7)

1.0 V

0 (0

p-p

90 mV 0 (0.1)

7.7 (0)

)

0 (0)

0(0.4

5.0 (5.0)

)

0.33 V

5.5 (0)

4.4 (0)

0.9(0)

p-p

0 (8.6)

5.6 (0)

0 (0)

0.1 (0)

5.2(0)

115 mV

4.0 (4.0)

p-p

0.86 V

p-p

5.6

p-p

330 mV

0.5 (0)

0.6

0.7 (0)

4.0 (4.0)

4.2 (0) 0 (0)

0 (0)

0.6 (0)

0 (5.0)

4.8 (4.8)

8.9 (0)

8.0 (0)

0.7 (0)

4.9 (4.9)

5.0 (5.1)

4.0 (4.0)

5.0 (5.0)

2.3 (2.3)

0.1 (0.1)

3.9 (3.9)

12.9 (12.8)

6.8 (6.0)

p-p

4.0 (0.1)

4.0 (4.0)

4.0 (7.9)

4.3 (7.9)

3.2 (3.2)

5.0 (5.0)

2.7 (2.8)

5.0 (5.0)

5.0

2.7 (2.7)

2.5 (2.5)

4.5 (4.5)

5.0 (0)

2.5 (2.6)

4.9 (4.9)

5.0 (5.0)

0 (0)

5.0 (5.0)

3.4 (3.4) 3.0 (3.0)

2.7 (2.8)

2.5 (2.5)

4.7(4.7)

4.7 (4.7)

5.0 (5.0)

0 (0)

5.0 (0)

5.0 (5.0)

0 (0)

5.0 (5.0)

0 (0)

4.9 (4.9)

0 (0)

3.9 V

2.0 (2.0)

5.0 (5.0)

2.1 (2.1)

p-p

2.1

1.7 (1.7)

(2.0)

p-p

1.0 V

2.1 (2.1)

1.0 V

2.0 (2.0)

p-p

2.0 (2.0)

1.6 V

2.4 (2.4)

p-p

8.9 (8.9)

1.9 (1.9)

2.8 (8.2)

9.0 (0)

2.7 (2.8)

9.0 (0)

0.8 (0)

5.1 (5.1)

88 mV

7.8 V

4.0 (4.0)

0 (0)

p-p

440 mV

2.1 (2.1)

5.8 V

2.1 (2.1)

p-p

4.0 (4.0)

370 mV

2.5 (2.5)

p-p

114 mV

4.0 (4.0)

0 (4.9)

4.9 (4.9)

3.0 (3.0)

0 (0)

2.4 (2.4)

3.2 (3.2)

114.5 mV 0 (0)

9.0 (9.0)

p-p

5.0 (5.0)

0 (0)

4.6 (0.1)

0 (0)

XX : RX 465.300 MHz, wide, Inject +30 dBµ at ±3.0 kHz deviation (XX): TX 465.300 MHz, Hi power, Inject – 25.7 dBm at 1 kHz tone

5.0 (5.0) 0 (0) 5.0 (5.0)

4.7 (0)

4.4 (4.4)

5.0 (5.0)

0 (0)

13.6 (13.6)

13.6 (13.5)

4.6 (0.1)

Page 24

MAIN Unit (Lot. 1~)

Note:

Page 25

Parts Layout

A C E FB D G H

MAIN Unit (Lot. 1~)

MB89P677ARFM (Lot. 1~) MB89677ARPFM (Lot. 2~) (Q1039)

SC370651FR2 (Q1049)

MX165BDW (Q1009)

BA4116FV TA31136FN (Lot. 2~) (Q1029)

NJM2902V (Q1007, 1016)

NJM2904V (Q1017)

TDA2003H (Q1003)

2SB1143S (Q1014)

MA143 (MC) (D1017)

DAP202U (P) (D1016, 1036)

DTC124EU (25) (Q1050, 1053)

2SC3357 (RK) (Q1031)

SGM2016M (M-) (Q1021)

2SK880GR (XG) (Q1043)

IMZ1 (Z1) (Q1022)

Side A

IMH6 (H6) (Q1035)

HA17805P (Q1010)

RH5VA45AA (D5) (Q1036)

2SB1201STP (Q1002)

2SC4116GR (LG) (Q1015, 1042) 2SC4215Y (QY) (Q1026) 2SC4226 (R24) (Q1047) 2SC4227 (R34) (Q1012) 2SC5107O (MFO) (Q1044)

Page 26

MAIN Unit (Lot. 1~)

a c e fb d g h

Side B

M57729H (Q1011)

MM1216ENRE (1A) (Q1001)

BR93LC66RF (Q1048)

AN8005M (Q1030)

IMH6 (H6) (Q1004, 1025, 1052)

2SC3357 (RK) (Q1028)

DTB123EK (F12) (Q1006)

DTB113ZK (G11) (Q1005)

DTC124EU (25) (Q1020, 1033, 1051)

2SA1586Y (SY) (Q1032, 1034)

2SC4116GR (LG) (Q1040, 1045, 1046) 2SC5107O (MFO) (Q1038, 1041)

DTC323TK (H02) (Q1008)

HZM7C (24) (D1024)

02CZ5.6Y (5.6) (D1018, 1029)

MA143 (MC) (D1037)

1SS321 (F9) (D1006) MA142WK (MU) (D1019) DAN235K (M) (D1026)

Page 27

Circuit Diagram

MAIN Unit (Lot. 4~)

Page 28

MAIN Unit (Lot. 4~)

Note:

Page 29

Parts Layout

A C E FB D G H

MAIN Unit (Lot. 4~)

MB89P677ARFM (Lot. 1~) MB89677ARPFM (Lot. 2~) (Q1039)

SC370651FR2 (Q1049)

MX165BDW MX165CDW (Lot. 5~) (Q1009)

BA4116FV TA31136FN (Lot. 2~) (Q1029)

NJM2902V (Q1007, 1016)

NJM2904V (Q1017)

TDA2003H (Q1003)

2SB1143S (Q1014)

MA143 (MC) (D1017)

DAP202U (P) (D1016, 1036)

DTC124EU (25) (Q1050, 1053)

2SC3357 (RK) (Q1031)

SGM2016M (M-) (Q1021)

2SK880GR (XG) (Q1043)

IMZ1 (Z1) (Q1022)

Side A

IMH6 (H6) (Q1035)

HA17805P (Q1010)

RH5VA45AA (D5) (Q1036)

2SB1201STP (Q1002)

2SC4116GR (LG) (Q1015, 1042) 2SC4215Y (QY) (Q1026) 2SC4226 (R24) (Q1047) 2SC4227 (R34) (Q1012) 2SC5107O (MFO) (Q1044)

Page 30

MAIN Unit (Lot. 4~)

a c e fb g h

M57729H M57729L (Ver. A : Lot. 4~) M57729SH-01 (Ver. F : Lot. 5~) M57729H-34 (Ver. D : Lot. 6~) (Q1011)

BR93LC66RF (Q1048)

IMH6 (H6) (Q1004, 1025, 1052)

DTB123EK (F12) (Q1006)

DTC124EU (25) (Q1020, 1033, 1051)

2SC4116GR (LG) (Q1040, 1045, 1046) 2SC5107O (MFO) (Q1038, 1041)

HZM7C (24) (D1024)

Side B

MA143 (MC) (D1037)

1SS321 (F9) (D1006) MA142WK (MU) (D1019) DAN235K (M) (D1026)

MM1216ENRE (1A) (Q1001)

AN8005M (Q1030)

2SC3357 (RK) (Q1028)

DTB113ZK (G11) (Q1005)

2SA1586Y (SY) (Q1032, 1034)

DTC323TK (H02) (Q1008)

02CZ5.6Y (5.6) (D1018, 1029)

Page 31

Circuit Diagram

MAIN Unit (Lot. 7~)

Page 32

MAIN Unit (Lot. 7~)

Note:

Page 33

Parts Layout

A C E FB D G H

MAIN Unit (Lot. 7~)

MB89P677ARFM (Lot. 1~) MB89677ARPFM (Lot. 2~) (Q1039)

SC370651FR2 (Q1049)

MX165BDW MX165CDW (Lot. 5~) (Q1009)

BA4116FV TA31136FN (Lot. 2~) (Q1029)

NJM2902V (Q1007, 1016)

NJM2904V (Q1017)

TDA2003H (Q1003)

2SB1143S (Q1014)

MA143 (MC) (D1017)

DAP202U (P) (D1016, 1036)

DTC124EU (25) (Q1050, 1053)

2SC3357 (RK) (Q1031)

SGM2016M (M-) SGM2016AM (Lot. 7~) (MA) (Q1021)

2SK880GR (XG) (Q1043)

IMZ1 (Z1) (Q1022)

Side A

IMH6 (H6) (Q1035)

HA17805P (Q1010)

RH5VA45AA (D5) (Q1036)

2SB1201STP (Q1002)

2SC4116GR (LG) (Q1015, 1042) 2SC4215Y (QY) (Q1026) 2SC4226 (R24) (Q1047) 2SC4227 (R34) (Q1012) 2SC5107O (MFO) 2SC4226 (Lot. 7~) (R24) (Q1044)

Page 34

MAIN Unit (Lot. 7~)

a c e fb d g h

M57729H M57729L (Ver. A : Lot. 4~) M57729SH-01 (Ver. F : Lot. 5~) M57729H-34 (Ver. D : Lot. 6~) (Q1011)

BR93LC66RF (Q1048)

IMH6 (H6) (Q1004, 1025, 1052)

DTB123EK (F12) (Q1006)

DTC124EU (25) (Q1020, 1033, 1051)

2SC4116GR (LG) (Q1040, 1045, 1046) 2SC5107O (MFO) (Q1038, 1041)

HZM7C (24) (D1024)

Side B

MA143 (MC) (D1037)

1SS321 (F9) (D1006) MA142WK (MU) (D1019) DAN235K (M) (D1026)

MM1216ENRE (1A) (Q1001)

AN8005M (Q1030)

2SC3357 (RK) (Q1028)

DTB113ZK (G11) (Q1005)

2SA1586Y (SY) (Q1032, 1034)

DTC323TK (H02) (Q1008)

02CZ5.6Y (5.6) (D1018, 1029)

Page 35

Circuit Diagram

MAIN Unit (Lot. 10~)

Page 36

MAIN Unit (Lot. 10~)

Note:

Page 37

Parts Layout

A C E FB D G H

MAIN Unit (Lot. 10~)

MB89P677ARFM (Lot. 1~) MB89677ARPFM (Lot. 2~) (Q1039)

SC370651FR2 MC145192FR2 (Lot. 19~) MC145193FR2 (Lot. 23~) (Q1049)

MX165BDW MX165CDW (Lot. 5~) (Q1009)

BA4116FV TA31136FN (Lot. 2~) (Q1029)

NJM2902V (Q1007, 1016)

NJM2904V (Q1017)

TDA2003H (Q1003)

2SB1143S (Q1014)

MA143 (MC) (D1017)

DAP202U (P) (D1016, 1036)

DTC124EU (25) (Q1050, 1053)

2SC3357 (RK) (Q1031)

SGM2016M (M-) SGM2016AM (Lot. 7~) (MA) (Q1021)

2SK880GR (XG) (Q1043)

IMZ1 (Z1) (Q1022)

IMH6 (H6) (Q1035)

Side A

RH5VA45AA (Lot. 1~) (D5) RH5VT45AA (Lot. 10~) (Q1036)

HA17805P (Lot. 1~) (Q1010)

2SB1201STP (Q1002)

KIA7805API (Lot. 57~) (Q1010)

2SC4116GR (LG) (Q1015, 1042) (Lot. 19~ : Q1054) 2SC4215Y (QY) (Q1026) 2SC4226 (R24) (Q1047) 2SC4227 (R34) (Q1012) 2SC5107O (MFO) 2SC4226 (Lot. 7~) (R24) (Q1044)

Page 38

MAIN Unit (Lot. 10~)

a c e fb d g h

M57729H M57729L (Ver. A : Lot. 4~) M57729SH-01 (Ver. F : Lot. 5~) M57729H-34 (Ver. D : Lot. 6~) (Q1011)

BR93LC66RF BR93L66RF (Lot. 62~) (Q1048)

IMH6 (H6) (Q1004, 1025, 1052)

DTB123EK (F12) (Q1006)

DTC124EU (25) (Q1020, 1033, 1051)

2SC4116GR (LG) (Q1040, 1045, 1046) 2SC5107O (MFO) (Q1038, 1041)

HZM7C (24) HZM7.5NB2 (Lot. 44~) () (D1024)

Side B

MA143 (MC) (D1037)

1SS321 (F9) (D1006) MA142WK (MU) (D1019) DAN235K (M) (D1026)

MM1216ENRE (1A) (Q1001)

AN8005M (Q1030)

2SC3357 (RK) (Q1028)

DTB113ZK (G11) (Q1005)

2SA1586Y (SY) (Q1032, 1034)

DTC323TK (H02) (Q1008)

02CZ5.6Y (5.6) (D1018, 1029)

Page 39

Parts List

MAIN Unit

REF.

C 1001 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B f1 C 1002 CHIP CAP. 4pF 200V CH GRM40CH040C200PT K22230211 1-3 A G1 C 1002 CHIP CAP. 2pF 200V CH GRM40CH020C200PT K22230206 VERSION A 4- A G1 C 1002 CHIP CAP. 4pF 200V CH GRM40CH040C200PT K22230211 VERSION D 4- A G1 C 1002 CHIP CAP. 2pF 200V CH GRM40CH020C200PT K22230206 VERSION F 5- A G1 C 1003 CHIP CAP. 220pF 200V CG C17CG221K6TXLT K22233211 1- B a1 C 1003 CHIP CAP. 220pF 200V CG ATC700B221KW200XT K22233217 27- B a1 C 1004 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B f1 C 1005 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A B1 C 1005 AL.ELECTRO.CAP. 3300uF 16V RE3-16V332M 3300UF K40129065 9- A B1 C 1007 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B a2 C 1008 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A A1 C 1009 CHIP CAP. 9pF 200V CH GRM40CH090D200PT K22230215 1-4 B b1 C 1009 CHIP CAP. 9pF 200V CH GRM40CH090D200PT K22230215 VERSION A 5- B b1 C 1009 CHIP CAP. 9pF 200V CH GRM40CH090D200PT K22230215 VERSION D 5- B b1 C 1009 CHIP CAP. 7pF 200V CH GRM40CH070D200PT K22230213 VERSION F 5- B b1 C 1010 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1011 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1012 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A H2 C 1013 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b2 C 1014 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1015 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A G3 C 1016 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1017 CHIP CAP. 2pF 200V CH GRM40CH020C200PT K22230206 1- B b1 C 1018 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B a3 C 1019 CHIP CAP. 3pF 200V CJ GRM40CJ030C200PT K22230210 VERSION A 4- B b1 C 1019 CHIP CAP. 2pF 200V CH GRM40CH020C200PT K22230206 VERSION F 5- B b1 C 1020 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B g1 C 1021 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B f2 C 1022 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-3 B b1 C 1022 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION A 4- B b1 C 1022 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION D 4- B b1 C 1022 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION F 5- B b1 C 1023 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- B g1 C 1024 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b1 C 1025 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B a2 C 1026 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B g1 C 1027 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1-6 C 1029 AL.ELECTRO.CAP. 10uF 16V RC2-16V100M(4X7) K40129012 1- A G2 C 1030 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B a2 C 1031 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B f2 C 1032 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b1 C 1033 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B a2 C 1034 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b2 C 1035 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A B3 C 1036 CHIP CAP. 5pF 200V CH GRM40CH050C200PT K22230207 1-3 A F1 C 1036 CHIP CAP. 6pF 200V CH GRM40CH060D200PT K22230212 VERSION A 4- A F1 C 1036 CHIP CAP. 5pF 200V CH GRM40CH050C200PT K22230207 VERSION D 4- A F1 C 1036 CHIP CAP. 5pF 200V CH GRM40CH050C200PT K22230207 VERSION F 5- A F1 C 1037 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C3 C 1038 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1- B f2 C 1039 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 1- B b1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** MAIN UNIT *** PCB with Components CS1573001 TYPE D PCB with Components CS1573002 TYPE A PCB with Components CS1573003 TYPE F Printed Circuit Board FR002190B 1- Printed Circuit Board FR002190C 4- Printed Circuit Board FR002190D 7- Printed Circuit Board FR002190D 10-

LOT. SIDE.

LAY ADR.

Page 40

MAIN Unit

REF.

C 1041 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 1-3 A E1 C 1041 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 VERSION D 4- A E1 C 1041 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION F 5- A E1 C 1042 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- B b1 C 1044 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f2 C 1045 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 1-3 A E1 C 1045 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION A 4- A E1 C 1045 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION D 4- A E1 C 1045 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION F 5- A E1 C 1046 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-3 A E1 C 1046 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION A 4- A E1 C 1046 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION D 4- A E1 C 1046 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION F 5- A E1 C 1047 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B f2 C 1048 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B f2 C 1049 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- A B2 C 1050 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- B a2 C 1051 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 1- B b2 C 1052 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 1-3 A E1 C 1052 CHIP CAP. 11pF 50V CH GRM39CH110J50PT K22174212 VERSION A 4- A E1 C 1052 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 VERSION D 4- A E1 C 1052 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 VERSION F 5- A E1 C 1053 CHIP CAP. 2pF 200V CH GRM40CH020C200PT K22230206 VERSION A 4- A F2 C 1053 CHIP CAP. 3pF 200V CJ GRM40CJ030C200PT K22230210 VERSION F 5- A F2 C 1054 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 1-3 A E1 C 1054 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION A 4- A E1 C 1054 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 VERSION D 4- A E1 C 1054 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION F 5- A E1 C 1055 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A E1 C 1056 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 1-3 A E1 C 1056 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 VERSION A 4- A E1 C 1056 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION D 4- A E1 C 1056 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 VERSION F 5- A E1 C 1057 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- B b2 C 1058 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 1-3 A E1 C 1058 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION A 4- A E1 C 1058 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 VERSION D 4- A E1 C 1058 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION F 5- A E1 C 1059 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- B a1 C 1060 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A B2 C 1061 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B g2 C 1062 AL.ELECTRO.CAP. 10uF 16V ECEV1CS100SR K48120001 1- A F4 C 1063 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B c2 C 1064 AL.ELECTRO.CAP. 10uF 16V ECEV1CS100SR K48120001 1- A D1 C 1065 CHIP CAP. 0.01uF 25V B GRM39B103K25PT K22144803 1-61 B f2 C 1066 CHIP CAP. 0.033uF 16V R GRM39R333K16PT K22124801 1- B f2 C 1067 CHIP CAP. 68pF 50V CH GRM39CH680J50PT K22174231 1- B f2 C 1067 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 24- B f2 C 1068 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 1-3 A E1 C 1068 CHIP CAP. 11pF 50V CH GRM39CH110J50PT K22174212 VERSION A 4- A E1 C 1068 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 VERSION D 4- A E1 C 1068 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 VERSION F 5- A E1 C 1069 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1-6 A E2 C 1070 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A F4 C 1071 CHIP CAP. 68pF 50V CH GRM39CH680J50PT K22174231 1- B f2 C 1071 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 24- B f2 C 1072 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 1-3 A E1 C 1072 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION A 4- A E1 C 1072 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION D 4- A E1 C 1072 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION F 5- A E1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT. SIDE.

LAY ADR.

Page 41

MAIN Unit

REF.

C 1073 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 1-3 A E1 C 1073 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 VERSION A 4- A E1 C 1073 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION D 4- A E1 C 1073 CHIP CAP. 8pF 50V CH GRM39CH080D50PT K22174209 VERSION F 5- A E1 C 1074 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B f2 C 1075 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B g2 C 1076 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1-6 A D2 C 1077 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A D2 C 1078 CHIP TA.CAP. 10uF 20V TEMSVB21D106M-8R K78130028 1- A D2 C 1079 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D2 C 1080 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A E1 C 1081 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A E3 C 1082 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A D1 C 1083 AL.ELECTRO.CAP. 10uF 16V ECEV1CS100SR K48120001 1- A F3 C 1084 CHIP CAP. 470pF 50V CH GRM39CH471J50PT K22174249 1- A B1 C 1085 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D1 C 1086 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A E1 C 1087 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B g2 C 1089 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A C1 C 1090 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-3 A D1 C 1090 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION A 4- A D1 C 1090 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION D 4- A D1 C 1090 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 VERSION F 5- A D1 C 1091 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-3 A D1 C 1091 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION A 4- A D1 C 1091 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION D 4- A D1 C 1091 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION F 5- A D1 C 1093 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1-3 A D1 C 1093 CHIP CAP. 9pF 50V CH GRM39CH090D50PT K22174210 VERSION A 4- A D1 C 1093 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION D 4- A D1 C 1093 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION F 5- A D1 C 1094 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 1-3 A D1 C 1094 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 VERSION A 4- A D1 C 1094 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION D 4- A D1 C 1094 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION F 5- A D1 C 1095 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 1-3 A D1 C 1095 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION A 4- A D1 C 1095 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 VERSION D 4- A D1 C 1095 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION F 5- A D1 C 1096 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f2 C 1097 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 1- A D1 C 1098 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b3 C 1099 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A D1 C 1100 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-4 A D1 C 1100 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION A 5- A D1 C 1100 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION D 5- A D1 C 1100 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION F 5- A D1 C 1101 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 1-3 A D1 C 1101 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION A 4- A D1 C 1101 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 VERSION D 4- A D1 C 1101 CHIP CAP. 3pF 50V CJ GRM39CJ030C50PT K22174204 VERSION F 5- A D1 C 1102 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B f2 C 1104 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- A G2 C 1105 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1-3 A D1 C 1105 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 VERSION A 4- A D1 C 1105 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION D 4- A D1 C 1105 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION F 5- A D1 C 1106 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 1-3 A D1 C 1106 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 VERSION A 4- A D1 C 1106 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION D 4- A D1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT. SIDE.

LAY ADR.

Page 42

MAIN Unit

REF.

C 1106 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION F 5- A D1 C 1107 CHIP CAP. 18pF 50V CH GRM39CH180J50PT K22174217 1- A C2 C 1107 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 7-36 A C2 C 1107 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 DST:THA 37- A C2 C 1107 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 EXPORT 37- A C2 C 1107 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 C 1107 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 STANDARD 37- A C2 C 1107 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 THAILAND 37- A C2 C 1107 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 VTX(USA) 37- A C2 C 1108 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A G2 C 1109 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- A G2 C 1110 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-3 A D1 C 1110 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION A 4- A D1 C 1110 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION D 4- A D1 C 1110 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 VERSION F 5- A D1 C 1111 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1-3 A D1 C 1111 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION A 4- A D1 C 1111 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION D 4- A D1 C 1111 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION F 5- A D1 C 1112 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A C2 C 1113 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- A C2 C 1114 CHIP CAP. 0.033uF 16V B ECJ1VB1C333K K22129515 1- A C2 C 1115 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 1-3 B d2 C 1115 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 VERSION A 4- B d2 C 1115 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 VERSION D 4- B d2 C 1115 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 VERSION F 5- B d2 C 1116 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C2 C 1117 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e2 C 1118 CHIP CAP. 560pF 50V B GRM39B561M50PT K22174806 1- A B2 C 1119 CHIP CAP. 120pF 50V CH GRM39CH121J50PT K22174237 1- A C1 C 1120 CHIP CAP. 390pF 50V CH GRM39CH391J50PT K22174255 1- A B2 C 1121 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A D1 C 1122 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A D1 C 1123 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A B2 C 1124 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 1- A D1 C 1125 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- A C2 C 1126 CHIP CAP. 560pF 50V B GRM39B561M50PT K22174806 1- A B2 C 1127 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 1- B d2 C 1128 CHIP CAP. 0.015uF 25V B GRM39B153K25PT K22144805 1- A B3 C 1129 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A E2 C 1130 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A B2 C 1131 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f3 C 1132 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 1-3 B e2 C 1132 CHIP CAP. 9pF 50V CH GRM39CH090D50PT K22174210 VERSION A 4- B e2 C 1132 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 VERSION D 4- B e2 C 1132 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION F 5- B e2 C 1133 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- A B3 C 1134 CHIP CAP. 27pF 50V CH GRM39CH270J50PT K22174221 1- A E2 C 1135 CHIP CAP. 0.022uF 25V B GRM39B223K25PT K22144807 1- A C2 C 1136 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D2 C 1137 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- A D2 C 1138 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B d2 C 1139 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1140 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 1- B f2 C 1141 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C2 C 1142 CHIP CAP. 0.001uF 50V B GRM39B102M50PT K22174809 1- A E2 C 1143 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 1- B c3 C 1144 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1145 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1146 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B f2

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

PORLAND CONSPAK

LOT. SIDE.

37- A C2

LAY ADR.

Page 43

MAIN Unit

REF.

C 1147 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B f2 C 1149 CHIP CAP. 39pF 50V CH GRM39CH390J50PT K22174225 1- A F2 C 1150 CHIP CAP. 0.33uF 16V B GRM40B334K16PT K22120807 1- B b2 C 1151 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b3 C 1152 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 1-3 A D2 C 1152 CHIP CAP. 8pF 50V CH GRM39CH080D50PT K22174209 VERSION A 4- A D2 C 1152 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 VERSION D 4- A D2 C 1152 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION F 5- A D2 C 1153 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1154 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b3 C 1155 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C2 C 1156 CHIP CAP. 82pF 50V CH GRM39CH820J50PT K22174233 1- B b2 C 1157 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B b3 C 1158 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B b2 C 1159 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B b2 C 1160 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B b2 C 1161 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C3 C 1162 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 1- A A2 C 1163 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- A C3 C 1164 AL.ELECTRO.CAP. 10uF 16V ECEV1CS100SR K48120001 1- A F2 C 1165 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A F2 C 1166 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B g2 C 1167 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B b2 C 1168 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 1- A D2 C 1169 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D2 C 1170 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B g2 C 1171 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- A G2 C 1172 CHIP CAP. 0.0056uF 50V B ECJ1VB1H562K K22179623 1- A F2 C 1173 CHIP TA.CAP. 2.2uF 10V TESVA1A225M1-8R K78100021 1- A A2 C 1174 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B a2 C 1175 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 1- A G2 C 1176 CHIP CAP. 1uF 16V B GRM42-6B105K16NPT K22121803 1- B a2 C 1177 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B a2 C 1178 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- A A2 C 1179 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 1- B d3 C 1180 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B f3 C 1181 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f3 C 1182 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B f3 C 1183 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B f3 C 1184 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A B3 C 1185 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A B3 C 1186 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A C3 C 1187 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A C3 C 1188 CHIP CAP. 2pF 50V CK GRM39CK020C50PT K22174203 1- B d3 C 1189 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D4 C 1190 CHIP CAP. 0.1uF 25V B GRM40B104M25PT K22140811 1- B d2 C 1191 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A D3 C 1192 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- B e3 C 1193 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- A D4 C 1194 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 1-3 A D3 C 1195 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C3 C 1196 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- A D3 C 1197 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1-4 A D3 C 1197 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION A 5- A D3 C 1197 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 VERSION D 5- A D3 C 1197 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 VERSION F 5- A D3 C 1198 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D3 C 1199 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1- B e3 C 1200 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1201 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT. SIDE.

LAY ADR.

Page 44

MAIN Unit

REF.

C 1202 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- A C4 C 1203 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 1- B g3 C 1204 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D3 C 1205 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 1- B e3 C 1206 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 1- B g3 C 1207 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- A F3 C 1208 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B e3 C 1209 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 1- A E3 C 1210 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A E3 C 1211 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 1-6 A C3 C 1211 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 VERSION A 7- A C3 C 1211 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 VERSION D 7- A C3 C 1211 CHIP CAP. 5pF 50V CH GRM39CH050C50PT K22174206 VERSION F 7- A C3 C 1212 CHIP CAP. 22pF 50V CH GRM39CH220J50PT K22174219 1- B g3 C 1213 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1214 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1215 CHIP CAP. 56pF 50V CH GRM39CH560J50PT K22174229 1- B c3 C 1215 CHIP CAP. 47pF 50V CH GRM39CH470J50PT K22174227 5- B c3 C 1216 CHIP CAP. 15pF 50V UJ GRM39UJ150J50PT K22174312 1- A F3 C 1216 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 5- A F3 C 1217 CHIP CAP. 8pF 50V CH GRM39CH080D50PT K22174209 1- A E3 C 1218 CHIP CAP. 7pF 50V CH GRM39CH070D50PT K22174208 1- A E3 C 1219 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1220 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 1- A E3 C 1222 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- B e3 C 1223 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B c3 C 1224 CHIP CAP. 6pF 50V CH GRM39CH060D50PT K22174207 1- A E3 C 1225 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A E3 C 1226 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B e3 C 1227 CHIP CAP. 33pF 50V CH GRM39CH330J50PT K22174223 1- B e3 C 1228 CHIP TA.CAP. 2.2uF 10V TESVA1A225M1-8R K78100021 1- B d3 C 1229 CHIP CAP. 0.5pF 50V CK GRM39CK0R5C50PT K22174201 1- A E3 C 1230 CHIP CAP. 100pF 50V CH GRM39CH101J50PT K22174235 1- B e3 C 1231 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A D3 C 1232 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- B d3 C 1233 CHIP CAP. 15pF 50V CH GRM39CH150J50PT K22174215 1- B c3 C 1234 CHIP CAP. 10pF 50V CH GRM39CH100D50PT K22174211 1- B c3 C 1235 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A E3 C 1236 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- A B3 C 1237 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A E3 C 1238 CHIP CAP. 0.047uF 16V B GRM39B473K16PT K22124804 1- B d3 C 1239 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B e3 C 1240 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1- B f3 C 1241 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- B c3 C 1242 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B d3 C 1243 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- B c3 C 1244 CHIP CAP. 4pF 50V CH GRM39CH040C50PT K22174205 1- A E3 C 1245 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A D3 C 1246 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 1- A C3 C 1247 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A D3 C 1248 CHIP CAP. 0.0033uF 50V B GRM39B332M50PT K22174815 1- B a2 C 1249 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f2 C 1250 CHIP CAP. 0.1uF 16V B GRM39B104K16PT K22124805 1- B f2 C 1251 CHIP CAP. 0.0018uF 50V B GRM39B182M50PT K22174812 1- B f2 C 1252 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 1-6 B b3 C 1253 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- B d2 C 1256 CHIP CAP. 220pF 50V CH GRM40CH221J50PT K22170243 1- A D2 C 1256 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 4- A D2 C 1257 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 1- B b1 C 1258 CHIP CAP. 1pF 50V CK GRM39CK010C50PT K22174202 1- B b2

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT. SIDE.

LAY ADR.

Page 45

MAIN Unit

REF.

C 1259 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- B d2 C 1260 TANTALUM CAP. 10uF 16V DN1C100M1S K70127106 1- B d3 C 1260 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 4- B d3 C 1261 CHIP CAP. 1uF 10V F GRM39F105Z10PT K22105001 4- B g2 C 1262 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- B d3 C 1263 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 1- A C3 C 1264 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 5-6 A G3 C 1265 CHIP CAP. 220pF 200V CH GRM40CH221J200PT K22230232 VERSION A 7- A F2 C 1265 CHIP CAP. 220pF 200V CH GRM40CH221J200PT K22230232 VERSION D 7- A F2 C 1265 CHIP CAP. 7pF 200V CH GRM40CH070D200PT K22230213 VERSION F 5- A F2 C 1266 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 7- A C1 C 1267 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 VERSION F 5-6 A E2 C 1267 AL.ELECTRO.CAP. 470uF 16V RE3-16V471M 470UF K40129066 7- A E2 C 1268 TANTALUM CAP. 47uF 10V DN1A470M1S K70107476 VERSION F 5-6 A G3 C 1268 CHIP TA.CAP. 68uF 10V TEMSVC1A686M12R K78100048 7- A G3 C 1270 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 7- A E2 C 1271 CHIP CAP. 0.001uF 50V B GRM39B102K50PT K22174821 7- A D1 C 1274 CHIP TA.CAP. 10uF 10V TEMSVA1A106M-8R K78100028 19- A C3 C 1275 CHIP CAP. 220pF 50V CH GRM39CH221J50PT K22174243 25- CD1001 CERAMIC DISC CDBM450C24T H7901060 1- A F2 CD1001 CERAMIC DISC CDBC450CX24-TC H7901340 10- A F2 CF1001 CERAMIC FILTER CFWM450G H3900435 1- A F3 CF1002 CERAMIC FILTER CFWM450E H3900466 1- A F3 CO1001 CERAMIC OSC 1MHz KBR-1000YTR17 H7900840 1- A B1 CO1001 CERAMIC OSC 1MHz CSB1000J221T H7900550 23- A B1 D 1001 SURGE ABSORBER P6KE18 Q9000534 1- A B1 D 1001 SURGE ABSORBER P6KA18 Q9000721 7- A B1 D 1002 DIODE UM9957F/TR G2070562 1- B b1 D 1003 DIODE MI407 G2090345 1- A F1 D 1003 DIODE XB15A407A2GB G2090741 7- A F1 D 1005 DIODE RLS135 TE-11 G2070128 1- A E1 D 1006 DIODE 1SS321 TE85R G2070076 1- B b2 D 1007 DIODE HVU350TRF G2070380 1- A E1 D 1008 DIODE HVU350TRF G2070380 1- A E1 D 1009 DIODE 1SS355 TE-17 G2070470 1- A E1 D 1010 DIODE 1SS355 TE-17 G2070470 1- B g2 D 1011 DIODE HVU350TRF G2070380 1- A D1 D 1012 DIODE HVU350TRF G2070380 1- A D1 D 1013 DIODE HVU350TRF G2070380 1- A D1 D 1014 DIODE HVU350TRF G2070380 1- A D1 D 1015 DIODE 1SS355 TE-17 G2070470 1- A G2 D 1016 DIODE DAP202U T106 G2070160 1- A B3 D 1017 DIODE MA143-(TX) G2070536 1- A E2 D 1018 DIODE 02CZ5.6Y TE85R G2070300 1- B b2 D 1019 DIODE MA142WK-(TX) G2070534 1- B b3 D 1021 DIODE 1SS355 TE-17 G2070470 1- B b3 D 1022 DIODE 1SS355 TE-17 G2070470 1- B b3 D 1023 DIODE D1F20-4063 G2070474 1- B g1 D 1024 DIODE HZM7C-TR G2070070 1- B g2 D 1024 DIODE HZM7.5NB2 TR G2070864 44- B g2 D 1025 DIODE 1SS355 TE-17 G2070470 1- B g2 D 1026 DIODE DAN235K T97 G2070082 1- B e2 D 1027 DIODE 1SS355 TE-17 G2070470 1- A A2 D 1028 DIODE MA729-(TX) G2070320 1- A A2 D 1029 DIODE 02CZ5.6Y TE85R G2070300 1- B d2 D 1030 DIODE 1SV230 TPH3 G2070126 1- B c3 D 1031 DIODE 1SV230 TPH3 G2070126 1- A E3 D 1032 DIODE 1SS355 TE-17 G2070470 1- B g3 D 1033 DIODE 1SS355 TE-17 G2070470 1- B e3 D 1034 DIODE HSU277TRF G2070118 1- A E3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT. SIDE.

LAY ADR.

Page 46

MAIN Unit

REF.

D 1035 DIODE 1SV230 TPH3 G2070126 1- B c3 D 1036 DIODE DAP202U T106 G2070160 1- A A3 D 1037 DIODE MA143-(TX) G2070536 1- B c3 D 1038 DIODE 1SV276(TPH3) G2070420 1- A D3 D 1039 DIODE 1SV276(TPH3) G2070420 1- A D3 D 1040 DIODE 1SS270 G2090408 1- B f2 D 1040 DIODE 1SS355 TE-17 G2070470 4- B f2 D 1041 DIODE 1SS355 TE-17 G2070470 4- B g3 D 1042 DIODE 1SS270 G2090408 4- B e3 D 1042 DIODE 1SS355 TE-17 G2070470 10- B e3 F 1001 CHIP FUSE 0.25A F0805B0R25FWTR Q0000072 1- A A1 F 1001 CHIP FUSE 0.25A TF20N0.25TE Q0000100 19- A A1 FB1001 FERRITE BEADS SMB304729 L9190094 1- B f1 FB1002 FERRITE BEADS SMB304729 L9190094 1- B f1 FB1003 FERRITE BEADS SMB304729 L9190094 1-6 FB1004 FERRITE BEADS SMB304729 L9190094 1-6 FB1005 FERRITE BEADS SMB304729 L9190094 1-6 J 1001 CONNECTOR SB20-03WS P0090610 1- A G3 J 1002 CONNECTOR SB20-02WS P0090609 1- A G4 J 1003 CONNECTOR AE0031-00 P1090998 1- B g1 J 1004 CONNECTOR IL-Y-14P-S15T2-E P0090601 1- A A4 J 1005 CONNECTOR IL-Y-8P-S15T2-EF P0090646 1- A A2 J 1006 CONNECTOR B11B-ZR P0091200 1- A B4 J 1007 CONNECTOR IL-Y-12P-S15T2-EF P0091201 1- A B3 JP1014 WIRE ASSY GRN 40 2/2 T50504000 L 1001 COIL A1 3.5T2.0D0.6UEW R L0020676A 1- A G1 L 1002 COIL A1 2.5T2.0D0.5UEW R L0021761A 1- A G1 L 1004 COIL A1 3.5T2.0D0.6UEW R L0020676A 1- A F1 L 1005 COIL E2 0.28-1.0-6T-R L0022366 1- A F1 L 1006 COIL E2 0.28-1.0-6T-R L0022366 1- A E1 L 1007 COIL A1 3.5T2.0D0.6UEW R L0020676A 1- A F1 L 1008 M.RFC 0.0153uH 33CS 655LY-03K=P3 L1690242 1-3 A E1 L 1008 M.RFC 0.0216uH 33CS 655LY-04K=P3 L1690243 VERSION A 4- A E1 L 1008 M.RFC 0.0153uH 33CS 655LY-03K=P3 L1690242 VERSION D 4- A E1 L 1008 M.RFC 0.0153uH 33CS 655LY-03K=P3 L1690242 VERSION F 5- A E1 L 1009 COIL A1 4.5T3.5D0.6UEW R L0020679A 1- A G2 L 1010 M.RFC 0.0153uH 33CS 655LY-03K=P3 L1690242 1-3 A E1 L 1010 M.RFC 0.0216uH 33CS 655LY-04K=P3 L1690243 VERSION A 4- A E1 L 1010 M.RFC 0.0153uH 33CS 655LY-03K=P3 L1690242 VERSION D 4- A E1 L 1010 M.RFC 0.0153uH 33CS 655LY-03K=P3 L1690242 VERSION F 5- A E1 L 1011 M.RFC 0.015uH HK1608 15NJ-T L1690518 1-3 A E1 L 1011 M.RFC 0.022uH HK1608 22NJ-T L1690520 VERSION A 4- A E1 L 1011 M.RFC 0.015uH HK1608 15NJ-T L1690518 VERSION D 4- A E1 L 1011 M.RFC 0.015uH HK1608 15NJ-T L1690518 VERSION F 5- A E1 L 1012 M.RFC 0.015uH HK1608 15NJ-T L1690518 1-3 A E1 L 1012 M.RFC 0.022uH HK1608 22NJ-T L1690520 VERSION A 4- A E1 L 1012 M.RFC 0.015uH HK1608 15NJ-T L1690518 VERSION D 4- A E1 L 1012 M.RFC 0.015uH HK1608 15NJ-T L1690518 VERSION F 5- A E1 L 1013 M.RFC 0.0498uH 36CS 656LZ-09K=P3 L1690248 1- A D1 L 1014 COIL E2 0.26-0.9-3T-R L0022367 1-4 A D1 L 1014 COIL E2 0.26-0.9-3T-R L0022367 VERSION A 5- A D1 L 1014 COIL E2 0.26-0.9-3T-R L0022367 VERSION D 5- A D1 L 1014 COIL E2 0.3-0.9-3T-R L0022389 VERSION F 5- A D1 L 1015 M.RFC 0.0498uH 36CS 656LZ-09K=P3 L1690248 1- A D1 L 1016 COIL E2 0.26-0.9-3T-R L0022367 1-4 A D1 L 1016 COIL E2 0.26-0.9-3T-R L0022367 VERSION A 5- A D1 L 1016 COIL E2 0.26-0.9-3T-R L0022367 VERSION D 5- A D1 L 1016 COIL E2 0.3-0.9-3T-R L0022389 VERSION F 5- A D1 L 1017 M.RFC 0.0498uH 36CS 656LZ-09K=P3 L1690248 1- A C1 L 1018 COIL E2 0.26-0.9-3T-R L0022367 1-4 A C1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

PORLAND CONSPAK

37-

SIDE.LOT.

LAY ADR.

Page 47

MAIN Unit

REF.

L 1018 COIL E2 0.26-0.9-3T-R L0022367 VERSION A 5- A C1 L 1018 COIL E2 0.26-0.9-3T-R L0022367 VERSION D 5- A C1 L 1018 COIL E2 0.3-0.9-3T-R L0022389 VERSION F 5- A C1 L 1019 M.RFC 0.0498uH 36CS 656LZ-09K=P3 L1690248 1- A C1 L 1020 COIL E2 0.26-0.9-3T-R L0022367 1-4 A C1 L 1020 COIL E2 0.26-0.9-3T-R L0022367 VERSION A 5- A C1 L 1020 COIL E2 0.26-0.9-3T-R L0022367 VERSION D 5- A C1 L 1020 COIL E2 0.3-0.9-3T-R L0022389 VERSION F 5- A C1 L 1021 M.RFC 0.027uH HK1608 27NJ-T L1690521 1-3 B e2 L 1021 M.RFC 0.039uH HK1608 39NJ-T L1690523 VERSION A 4- B e2 L 1021 M.RFC 0.027uH HK1608 27NJ-T L1690521 VERSION D 4- B e2 L 1021 M.RFC 0.022uH HK1608 22NJ-T L1690520 VERSION F 5- B e2 L 1022 M.RFC 0.047uH HK1608 47NJ-T L1690524 1-3 A C1 L 1022 M.RFC 0.082uH HK1608 82NJ-T L1690527 VERSION A 4- A C1 L 1022 M.RFC 0.047uH HK1608 47NJ-T L1690524 VERSION D 4- A C1 L 1022 M.RFC 0.047uH HK1608 47NJ-T L1690524 VERSION F 5- A C1 L 1023 M.RFC 0.047uH HK1608 47NJ-T L1690524 1-3 A C1 L 1023 M.RFC 0.047uH HK1608 47NJ-T L1690524 VERSION A 4- A C1 L 1023 M.RFC 0.039uH HK1608 39NJ-T L1690523 VERSION D 4- A C1 L 1023 M.RFC 0.033uH HK1608 33NJ-T L1690522 VERSION F 5- A C1 L 1024 M.RFC 0.015uH HK1608 15NJ-T L1690518 1-3 A C1 L 1024 M.RFC 0.039uH HK1608 39NJ-T L1690523 VERSION A 4- A C1 L 1024 M.RFC 0.022uH HK1608 22NJ-T L1690520 VERSION D 4- A C1 L 1024 M.RFC 0.027uH HK1608 27NJ-T L1690521 VERSION F 5- A C1 L 1025 CHIP COIL 0.82uH LQH1NR82M04 L1690145 1- A D1 L 1026 CHIP COIL 0.33uH LQH1NR33M04 L1690141 1- A E2 L 1027 CHIP COIL 0.0147uH LQN1A15NJ04 L1690251 1- A D2 L 1029 M.RFC 0.33uH LK1608 R33K-T L1690412 1- A F2 L 1030 M.RFC 0.068uH HK2125 68NK-T L1690387 1- A C2 L 1031 M.RFC 0.018uH HK2125 18NK-T L1690380 1- A C3 L 1032 M.RFC 0.015uH HK1608 15NJ-T L1690518 1- A D3 L 1033 M.RFC 0.027uH HK1608 27NJ-T L1690521 1- B e3 L 1034 M.RFC 0.022uH HK1608 22NJ-T L1690520 1- A D3 L 1035 M.RFC 10uH LK2125 100K-T L1690331 1- B g3 L 1036 M.RFC 0.027uH HK1608 27NJ-T L1690521 1- A C3 L 1037 COIL E2 0.28-1.0-4T-R L0022365 1-3 A E3 L 1037 COIL E2 0.28-1.0-7TR L0022422 VERSION A 4- A E3 L 1037 COIL E2 0.28-1.0-4T-R L0022365 VERSION D 4- A E3 L 1037 COIL E2 0.26-0.9-3T-R L0022367 VERSION F 5- A E3 L 1038 COIL E2 0.28-1.0-6T-R L0022366 1-3 A E3 L 1038 COIL E2 0.35-1.6-5T-L L0022457 VERSION A 4 A E3 L 1038 COIL E2 0.35-1.6-4.5T-L L0022577 VERSION A 5- A E3 L 1038 COIL E2 0.28-1.0-6T-R L0022366 VERSION D 4- A E3 L 1038 COIL E2 0.28-1.0-4.5T-R L0022395 VERSION F 5- A E3 L 1039 COIL E2 0.26-0.9-3T-R L0022367 1-3 A E3 L 1039 COIL E2 0.28-1.0-4.5T-R L0022395 VERSION A 4- A E3 L 1039 COIL E2 0.26-0.9-3T-R L0022367 VERSION D 4- A E3 L 1039 COIL E2 0.26-0.9-3T-R L0022367 VERSION F 5- A E3 L 1040 M.RFC 0.082uH HK1608 82NJ-T L1690527 1- A D3 L 1041 M.RFC 0.082uH HK1608 82NJ-T L1690527 1- A D3 Q 1001 IC MM1216ENRE G1092432 1- B b2 Q 1002 TRANSISTOR 2SB1201S-TL G3070195 1- A G3 Q 1003 IC TDA2003H G1090815 1- A H3 Q 1004 TRANSISTOR IMH6A T108 G3070066 1- B a2 Q 1005 TRANSISTOR DTB113ZK T146 G3070103 1- B a2 Q 1006 TRANSISTOR DTB123EK T146 G3070022 1- B a2 Q 1007 IC NJM2902V-TE1 G1091679 1- A B2 Q 1008 TRANSISTOR DTC323TK T146 G3070042 1- B g2 Q 1009 IC MX165BDW-TR G1092175 1- A B2 Q 1009 IC MX165CDW-TR G1092775 5- A B2

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

LOT. SIDE.

LAY ADR.

Page 48

MAIN Unit

REF.

Q 1010 IC HA17805P G1090936 1- A F4 Q 1010 IC KIA7805API G1093163 57- A F4 Q 1011 IC M57729H G1090754 1-3 B e1 Q 1011 IC M57729L G1090753 VERSION A 4- B e1 Q 1011 IC M57729H G1090754 VERSION D 4- B e1 Q 1011 IC M57729H-34 G1092805 VERSION D 6- B e1 Q 1011 IC M57729SH-01 G1090756 VERSION F 5- B e1 Q 1012 TRANSISTOR 2SC4227-T2 R34 G3342277D 1- A E1 Q 1014 TRANSISTOR 2SB1143S G3211430S 1- A F2 Q 1015 TRANSISTOR 2SC4116GR TE85R G3341167G 1- A F3 Q 1016 IC NJM2902V-TE1 G1091679 1- A B2 Q 1017 IC NJM2904V-TE1 G1091677 1- A G2 Q 1020 TRANSISTOR DTC124EU T106 G3070045 1- B f3 Q 1021 FET SGM2016M-T7 G4070005 1- A D1 Q 1021 FET SGM2016AM-T7 G4070012 7- A D1 Q 1022 TRANSISTOR IMZ1 T108 G3070025 1- A H2 Q 1025 TRANSISTOR IMH6A T108 G3070066 1- B f3 Q 1026 TRANSISTOR 2SC4215Y TE85R G3342157Y 1- A E2 Q 1028 TRANSISTOR 2SC3357-T2 G3333577 1- B e2 Q 1029 IC BA4116FV-E2 G1092616 1 A F2 Q 1029 IC TA31136FN(EL) G1091605 2- A F2 Q 1030 IC AN8005M-(E1) G1091454 1- B g2 Q 1031 TRANSISTOR 2SC3357-T2 G3333577 1- A D3 Q 1032 TRANSISTOR 2SA1586Y TE85R G3115867Y 1- B b2 Q 1033 TRANSISTOR DTC124EU T106 G3070045 1- B f2 Q 1034 TRANSISTOR 2SA1586Y TE85R G3115867Y 1- B g2 Q 1035 TRANSISTOR IMH6A T108 G3070066 1- A G2 Q 1036 IC RH5VL45AA-T1 G1090966 1- A A2 Q 1036 IC RH5VT45AA-T1 G1093215 10- A A2 Q 1036 IC RH5VL45AA-T1 G1090966 15- A A2 Q 1038 TRANSISTOR 2SC5107-O(TE85R) G3351077O 1- B d3 Q 1039 IC MB89P677APFM ø 1 A A3 Q 1039 IC Q 1039 IC Q 1039 IC Q 1040 TRANSISTOR 2SC4116GR TE85R G3341167G 1- B d2 Q 1041 TRANSISTOR 2SC5107-O(TE85R) G3351077O 1- B e3 Q 1042 TRANSISTOR 2SC4116GR TE85R G3341167G 1- A D4 Q 1043 FET 2SK880GR TE85R G3808807G 1- A D3 Q 1044 TRANSISTOR 2SC5107-O(TE85R) G3351077O 1- A D3 Q 1044 TRANSISTOR 2SC4226-T2B R24 G3342267D 7- A D3 Q 1045 TRANSISTOR 2SC4116GR TE85R G3341167G 1- B g3 Q 1046 TRANSISTOR 2SC4116GR TE85R G3341167G 1- B c3 Q 1047 TRANSISTOR 2SC4226-T2B R24 G3342267D 1- A E3 Q 1048 IC BR93LC66RF-E2 G1092006 1- B g3 Q 1048 IC BR93L66RF-WE2 G1093912 62- B g3 Q 1049 IC SC370651FR2 G1091937 1- A D3 Q 1049 IC MC145192FR2 G1092017 19- A D3 Q 1049 IC MC145193FR2 G1093424 23- A D3 Q 1050 TRANSISTOR DTC124EU T106 G3070045 1- A E3 Q 1051 TRANSISTOR DTC124EU T106 G3070045 1- B g3 Q 1052 TRANSISTOR IMH6A T108 G3070066 1- B f3 Q 1053 TRANSISTOR DTC124EU T106 G3070045 1- A C3 Q 1054 TRANSISTOR 2SC4116GR TE85R G3341167G 19- A C3 R 1001 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B a1 R 1002 CHIP RES. 4.7 1W 5% RMC1 4R7JTE J24305479 1- B a3 R 1003 CHIP RES. 4.7 1W 5% RMC1 4R7JTE J24305479 1- B a3 R 1004 CHIP RES. 1 1/10W 5% RMC1/10T 1R0J J24205010 1- B a3 R 1006 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1-36 B g1 R 1006 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 DST:THA 37- B g1

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

MB89677ARPFM-G-161-BND MB89677ARPFM-G-163-BND MB89677ARPFM-G-181-BND

ø 2- A A3 ø 4- A A3 ø 7- A A3

LOT. SIDE.

LAY ADR.

* Please contact VERTEX STANDARD.

Page 49

MAIN Unit

REF.

R 1006 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 EXPORT 37- B g1 R 1006 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 STANDARD 37- B g1 R 1006 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 THAILAND 37- B g1 R 1006 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 VTX(USA) 37- B g1 R 1007 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- B g1 R 1008 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- B g1 R 1009 CHIP RES. 270 1/10W 5% RMC1/10T 271J J24205271 1- B a2 R 1010 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g1 R 1011 CHIP RES. 560 1/16W 5% RMC1/16 561JATP J24185561 1- B f2 R 1014 CHIP RES. 2.7 1/16W 5% RMC1/16 2R7JATP J24185279 1- A G2 R 1015 CHIP RES. 470 1/4W 5% RMC1/4 471JATP J24245471 1- B b1 R 1016 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 1- B f2 R 1017 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 1- A C3 R 1018 CHIP RES. 1.5M 1/16W 5% RMC1/16 155JATP J24185155 1- B f2 R 1019 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- B b1 R 1021 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e3 R 1022 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B b1 R 1022 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 4- B b1 R 1023 CHIP RES. 8.2k 1/16W 5% RMC1/16 822JATP J24185822 1- B a1 R 1024 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B f2 R 1025 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B f2 R 1026 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- B b2 R 1027 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A E1 R 1028 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 1- A B2 R 1028 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 7- A B2 R 1029 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- A B2 R 1029 CHIP RES. 39k 1/16W 5% RMC1/16 393JATP J24185393 7- A B2 R 1030 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 1-36 B g2 R 1030 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 DST:THA 37- B g2 R 1030 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 EXPORT 37- B g2 R 1030 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 R 1030 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 STANDARD 37- B g2 R 1030 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 THAILAND 37- B g2 R 1030 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 VTX(USA) 37- B g2 R 1031 CHIP RES. 150 1W 5% RMC1 151JTE J24305151 1- B a1 R 1032 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B g2 R 1033 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A E1 R 1034 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 1- A B2 R 1035 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- B f2 R 1036 CHIP RES. 68k 1/16W 5% RMC1/16 683JATP J24185683 1- A E1 R 1038 CHIP RES. 470 1/10W 5% RMC1/10T 471J J24205471 1- B e2 R 1039 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 1- A B1 R 1040 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 1- B g2 R 1040 CHIP RES. 560k 1/16W 5% RMC1/16 564JATP J24185564 62- B g2 R 1043 CHIP RES. 22 1/10W 5% RMC1/10T 220J J24205220 1- B e2 R 1044 CHIP RES. 22 1/10W 5% RMC1/10T 220J J24205220 1- B e2 R 1045 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- B g2 R 1045 CHIP RES. 680k 1/16W 5% RMC1/16 684JATP J24185684 62- B g2 R 1046 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- A E1 R 1047 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- A E1 R 1048 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B1 R 1049 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- A C2 R 1051 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e2 R 1052 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1053 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1054 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B c3 R 1055 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- A F3 R 1056 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- B c3 R 1057 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1058 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- A G2

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

PORLAND CONSPAK

LOT. SIDE.

37- B g2

LAY ADR.

Page 50

MAIN Unit

REF.

R 1059 CHIP RES. 180k 1/16W 5% RMC1/16 184JATP J24185184 1- B f2 R 1061 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1062 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 1-36 A C2 R 1062 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 DST:THA 37- A C2 R 1062 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 EXPORT 37- A C2 R 1062 CHIP RES. 1.5M 1/16W 5% RMC1/16 155JATP J24185155 R 1062 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 STANDARD 37- A C2 R 1062 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 THAILAND 37- A C2 R 1062 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 VTX(USA) 37- A C2 R 1063 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1064 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D1 R 1065 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A C2 R 1066 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A C2 R 1067 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- A G2 R 1067 CHIP RES. 270k 1/16W 5% RMC1/16 274JATP J24185274 7- A G2 R 1068 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- A C2 R 1069 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- A C2 R 1070 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B a1 R 1071 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1-3 B e2 R 1071 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 VERSION A 4- B e2 R 1071 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 VERSION D 4- B e2 R 1071 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 VERSION F 5- B e2 R 1072 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 1- A C1 R 1073 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 1- A G2 R 1074 CHIP RES. 180k 1/16W 5% RMC1/16 184JATP J24185184 1- A C1 R 1075 CHIP RES. 150k 1/16W 5% RMC1/16 154JATP J24185154 1- A B2 R 1076 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B a1 R 1077 CHIP RES. 2.2M 1/16W 5% RMC1/16 225JATP J24185225 1- A B2 R 1078 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- A C1 R 1079 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A B2 R 1080 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 1- A C1 R 1081 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- B a2 R 1082 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1-3 A D1 R 1082 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 VERSION A 4- A D1 R 1082 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 VERSION D 4- A D1 R 1082 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 VERSION F 5- A D1 R 1083 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- A C1 R 1084 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1-6 R 1085 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A C2 R 1086 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- A D1 R 1087 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B f3 R 1088 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- A D1 R 1089 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 1- A B2 R 1090 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- A D1 R 1091 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 1- A D1 R 1092 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A C2 R 1093 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B2 R 1094 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A G2 R 1095 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A H2 R 1096 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- B a2 R 1097 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- B a2 R 1098 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B f3 R 1099 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A H2 R 1100 CHIP RES. 2.7k 1/16W 5% RMC1/16 272JATP J24185272 1- A H2 R 1100 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 7- A H2 R 1101 CHIP RES. 270 1/16W 5% RMC1/16 271JATP J24185271 1- A E2 R 1102 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- A B3 R 1103 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 1- A E2 R 1104 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A B3 R 1105 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1-3

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

PORLAND CONSPAK

LOT. SIDE.

37- A C2

LAY ADR.

Page 51

MAIN Unit

REF.

R 1106 CHIP RES. 470 1/10W 5% RMC1/10T 471J J24205471 1- B e2 R 1107 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B3 R 1108 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- A E2 R 1109 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 1- A C3 R 1110 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1-3 R 1111 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B f3 R 1112 CHIP RES. 39k 1/16W 5% RMC1/16 393JATP J24185393 1- A C3 R 1114 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 1-36 B f2 R 1114 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 DST:THA 37- B f2 R 1114 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 DST:THA 62- B f2 R 1114 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 EXPORT 37- B f2 R 1114 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 EXPORT 62- B f2 R 1114 CHIP RES. 150k 1/16W 5% RMC1/16 154JATP J24185154 R 1114 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 STANDARD 37- B f2 R 1114 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 STANDARD 62- B f2 R 1114 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 THAILAND 37- B f2 R 1114 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 THAILAND 62- B f2 R 1114 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 VTX(USA) 37- B f2 R 1114 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 VTX(USA) 62- B f2 R 1115 CHIP RES. 390k 1/16W 5% RMC1/16 394JATP J24185394 1- B f2 R 1116 CHIP RES. 680k 1/16W 5% RMC1/16 684JATP J24185684 1- B f2 R 1117 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B2 R 1118 CHIP RES. 0 1/10W 5% RMC1/10T 000J J24205000 1- A D2 R 1119 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1120 CHIP RES. 150k 1/16W 5% RMC1/16 154JATP J24185154 1- B f2 R 1121 CHIP RES. 270 1/16W 5% RMC1/16 271JATP J24185271 1- B b2 R 1122 CHIP RES. 10 1/10W 5% RMC1/10T 100J J24205100 1- A C2 R 1123 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1124 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1126 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1-9 R 1127 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B f2 R 1128 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 1- B f2 R 1129 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B f2 R 1130 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e2 R 1131 CHIP RES. 390k 1/16W 5% RMC1/16 394JATP J24185394 1 B b2 R 1132 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1133 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1134 CHIP RES. 3.3M 1/16W 5% RMC1/16 335JATP J24185335 1 B b2 R 1135 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B b2 R 1136 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b3 R 1137 CHIP RES. 820 1/16W 5% RMC1/16 821JATP J24185821 1 B b2 R 1137 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 2- B b2 R 1138 CHIP RES. 390k 1/16W 5% RMC1/16 394JATP J24185394 1 B b2 R 1138 CHIP RES. 680k 1/16W 5% RMC1/16 684JATP J24185684 2- B b2 R 1139 CHIP RES. 47 1/10W 5% RMC1/10T 470J J24205470 1- B e3 R 1140 CHIP RES. 1.5k 1/16W 5% RMC1/16 152JATP J24185152 1- B b2 R 1141 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- A C3 R 1142 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 1- B b2 R 1143 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A D3 R 1144 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A F2 R 1145 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- B b2 R 1146 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B b2 R 1147 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B b2 R 1148 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A A3 R 1149 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1150 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1 A F2 R 1150 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 2- A F2 R 1151 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A A3 R 1152 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B b2 R 1153 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B g2

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

PORLAND CONSPAK

LOT. SIDE.

37- B f2

LAY ADR.

Page 52

MAIN Unit

REF. DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

R 1154 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1156 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A F2 R 1157 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f3 R 1158 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- A D2 R 1159 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f3 R 1160 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1161 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A G2 R 1162 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1163 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B g2 R 1164 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1165 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A A2 R 1166 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1167 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP J24185682 1- A G2 R 1168 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B g3 R 1169 CHIP RES. 270k 1/16W 5% RMC1/16 274JATP J24185274 1- A G2 R 1170 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 1- B a2 R 1171 CHIP RES. 12k 1/16W 5% RMC1/16 123JATP J24185123 1- B b2 R 1172 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B f3 R 1173 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B d2 R 1174 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B a2 R 1175 CHIP RES. 1.5M 1/16W 5% RMC1/16 155JATP J24185155 1- A G2 R 1176 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A A2 R 1177 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B d3 R 1178 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f2 R 1179 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 1- B d3 R 1180 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B d2 R 1181 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 1-4 A D3 R 1181 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 VERSION A 5- A D3 R 1181 CHIP RES. 470k 1/16W 5% RMC1/16 474JATP J24185474 VERSION D 5- A D3 R 1181 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 VERSION F 5- A D3 R 1182 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 1- B f3 R 1183 CHIP RES. 15 1/16W 5% RMC1/16 150JATP J24185150 1- A D3 R 1184 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B d3 R 1185 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- A D3 R 1186 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f4 R 1187 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- B e3 R 1187 CHIP RES. 68k 1/16W 5% RMC1/16 683JATP J24185683 23- B e3 R 1188 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B f3 R 1189 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A D3 R 1189 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 10- A D3 R 1190 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- B f3 R 1191 CHIP RES. 27 1/10W 5% RMC1/10T 270J J24205270 1- B f3 R 1192 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A C3 R 1193 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- A C3 R 1194 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- B e3 R 1195 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- B f3 R 1196 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B c3 R 1197 CHIP RES. 1M 1/16W 5% RMC1/16 105JATP J24185105 1- B g3 R 1198 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- B c3 R 1199 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- A B3 R 1200 CHIP RES. 100 1/16W 5% RMC1/16 101JATP J24185101 1- A D3 R 1201 CHIP RES. 560 1/16W 5% RMC1/16 561JATP J24185561 1- A D3 R 1202 CHIP RES. 10 1/16W 5% RMC1/16 100JATP J24185100 1-18 B d3 R 1203 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1-3 B c3 R 1203 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 VERSION A 4 B c3 R 1203 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 VERSION D 4 B c3 R 1203 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 5- B c3 R 1204 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A B3 R 1205 CHIP RES. 1 1W 5% RMC1 1R0JTE J24305010 1- B b4 R 1206 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B c3

LOT. SIDE.

LAY ADR.

Page 53

MAIN Unit

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

R 1207 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A B3 R 1208 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A D3 R 1209 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A E3 R 1210 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- A B3 R 1211 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B g3 R 1212 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- A D3 R 1213 CHIP RES. 470 1/16W 5% RMC1/16 471JATP J24185471 1- A E3 R 1214 CHIP RES. 820k 1/16W 5% RMC1/16 824JATP J24185824 1- A D3 R 1215 CHIP RES. 47 1/16W 5% RMC1/16 470JATP J24185470 1- B e3 R 1216 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- B e3 R 1216 CHIP RES. 3.9k 1/16W 5% RMC1/16 392JATP J24185392 23- B e3 R 1217 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1218 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1- B e3 R 1219 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A B3 R 1220 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A E3 R 1221 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A E3 R 1222 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1223 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1224 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1225 CHIP RES. 5.6k 1/16W 5% RMC1/16 562JATP J24185562 1- B g3 R 1226 CHIP RES. 1.5k 1/16W 5% RMC1/16 152JATP J24185152 1- B d3 R 1227 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A E3 R 1228 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B d3 R 1229 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B e3 R 1230 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- B g3 R 1231 CHIP RES. 330k 1/16W 5% RMC1/16 334JATP J24185334 1- A E3 R 1232 CHIP RES. 56k 1/16W 5% RMC1/16 563JATP J24185563 1-4 A E3 R 1232 CHIP RES. 56k 1/16W 5% RMC1/16 563JATP J24185563 VERSION A 5- A E3 R 1232 CHIP RES. 56k 1/16W 5% RMC1/16 563JATP J24185563 VERSION D 5- A E3 R 1232 CHIP RES. 330k 1/16W 5% RMC1/16 334JATP J24185334 VERSION F 5- A E3 R 1233 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A D3 R 1234 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- B d3 R 1235 CHIP RES. 8.2k 1/16W 5% RMC1/16 822JATP J24185822 1- B d3 R 1236 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e3 R 1237 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- B e3 R 1238 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- B e3 R 1239 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 1- B c3 R 1240 CHIP RES. 22k 1/16W 5% RMC1/16 223JATP J24185223 1- A E3 R 1241 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 1- A A3 R 1242 CHIP RES. 68k 1/16W 5% RMC1/16 683JATP J24185683 1- A C3 R 1243 CHIP RES. 270k 1/16W 5% RMC1/16 274JATP J24185274 1- B c3 R 1244 CHIP RES. 220k 1/16W 5% RMC1/16 224JATP J24185224 1- B c3 R 1245 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- B e3 R 1246 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1-3 A D3 R 1246 CHIP RES. 270 1/16W 5% RMC1/16 271JATP J24185271 VERSION A 4- A D3 R 1246 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 VERSION D 4- A D3 R 1246 CHIP RES. 330 1/16W 5% RMC1/16 331JATP J24185331 VERSION F 5- A D3 R 1247 CHIP RES. 39k 1/16W 5% RMC1/16 393JATP J24185393 1- A D3 R 1248 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 1-3 B c3 R 1248 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 VERSION A 4 B c3 R 1248 CHIP RES. 15k 1/16W 5% RMC1/16 153JATP J24185153 VERSION D 4 B c3 R 1248 CHIP RES. 18k 1/16W 5% RMC1/16 183JATP J24185183 5- B c3 R 1249 CHIP RES. 56k 1/16W 5% RMC1/16 563JATP J24185563 1-3 B c3 R 1249 CHIP RES. 47k 1/16W 5% RMC1/16 473JATP J24185473 VERSION A 4 B c3 R 1249 CHIP RES. 56k 1/16W 5% RMC1/16 563JATP J24185563 VERSION D 4 B c3 R 1249 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 5- B c3 R 1250 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 1- B d3 R 1251 CHIP RES. 2.2k 1/16W 5% RMC1/16 222JATP J24185222 1- A C2 R 1252 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 1- B e3 R 1253 CHIP RES. 3.3k 1/16W 5% RMC1/16 332JATP J24185332 1- B f2

LOT. SIDE.

LAY ADR.

Page 54

MAIN Unit

REF. DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

R 1254 CHIP RES. 1k 1/16W 5% RMC1/16 102JATP J24185102 1- A D3 R 1255 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 1-3 R 1255 CHIP RES. 220 1/16W 5% RMC1/16 221JATP J24185221 VERSION D 4-9 R 1256 CHIP RES. 10k 1/16W 5% RMC1/16 103JATP J24185103 4- B g3 R 1257 CHIP RES. 0 1/8W 5% RMC1/8T 000J J24215000 7- A D2 R 1258 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 VERSION A 13- A D3 R 1258 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 VERSION D 13- A D3 R 1259 CHIP RES. 270 1/16W 5% RMC1/16 271JATP J24185271 19- A C3 R 1260 CHIP RES. 680 1/10W 5% RMC1/10T 681J J24205681 19- A C3 R 1261 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 10- A D3 R 1264 CHIP RES. 33k 1/16W 5% RMC1/16 333JATP J24185333 62- TC1001 TRIMMER CAP. 10pF ECR-KN010C61X K91000226 1- A E3 TC1001 TRIMMER CAP. 20pF ECR-KN020E61X K91000213 5- A E3 TH1001 THERMISTOR TBPS1R104K475H5Q G9090069 1- B a1 TH1003 THERMISTOR TBPS1R473K475H5Q G9090068 1- B c2 TH1004 THERMISTOR TBPS1R103K440H5Q G9090067 1- B c2 VR1001 POT. 10k EVN-5ESX50B14 J51811103 1- A C2 VR1002 POT. 50k EVN-5ESX50B54 J51811503 1- A G2 VR1003 POT. 10k EVN-5ESX50B14 J51811103 1- A G2 VR1004 POT. 50k EVN-5ESX50B54 J51811503 1- A B2 VR1005 POT. 50k EVN-5ESX50B54 J51811503 1- A B3 VR1006 POT. 10k EVN-5ESX50B14 J51811103 1- A G2 X 1001 XTAL LP-3.5.2S X 1002 XTAL UM-5 14.5MHz 14.5MHZ H0103175 1- A F3 XF1001 XTAL FILTER 43Y12B5F H1102307 1- A D2 XF1002 XTAL FILTER 43Y12B5F H1102307 1- A D2

SHIELD CASE RA0060200 1- LEAF SPRING R0129810 1-

9.8304MHz

9.8304MHZ H0103148 1- A A3

LOT. SIDE.

LAY ADR.

Page 55

Circuit Diagram

Display-1 Unit

Page 56

Display-1 Unit

Parts Layout

Side A

BU4094BCFV (Q2002)

XN1213 (9L) (Q2001, 2003, 2004)

DTC124EK (25) (Q2005)

Side B

Page 57

Parts List

Display-1 Unit

REF.

D 2001 LED HLMP-1540 G2090696 1- D 2002 LED HLMP-1540 G2090696 1- D 2003 LED HLMP-1540 G2090696 1- D 2004 LED HLMP-1540 G2090696 1- D 2005 LED HLMP-1440 G2090695 1- D 2006 LED HLMP-1540 G2090696 1- D 2007 LED TLS123 G2090703 1- D 2008 DIODE 1SS355 TE-17 G2070470 1- D 2009 DIODE 1SS355 TE-17 G2070470 1- JP2001 WIRE ASSY A0953+ T9206686 1- Q 2001 TRANSISTOR XN1213-(TX) G3070194 1- Q 2002 IC BU4094BCFV-E1 G1092128 1- Q 2002 IC BU4094BCFV-E2 G1093527 36- Q 2003 TRANSISTOR XN1213-(TX) G3070194 1- Q 2004 TRANSISTOR XN1213-(TX) G3070194 1- Q 2005 TRANSISTOR DTC124EK T146 G3070034 1- R 2001 CHIP RES. 220ohm 1/10W 5% RMC1/10T 221J J24205221 1- R 2002 CHIP RES. 10kohm 1/10W 5% RMC1/10T 103J J24205103 1- R 2003 CHIP RES. 220ohm 1/10W 5% RMC1/10T 221J J24205221 1- R 2004 CHIP RES. 220ohm 1/10W 5% RMC1/10T 221J J24205221 1- R 2005 CHIP RES. 220ohm 1/10W 5% RMC1/10T 221J J24205221 1- R 2006 CHIP RES. 220ohm 1/10W 5% RMC1/10T 221J J24205221 1- R 2007 CHIP RES. 220ohm 1/10W 5% RMC1/10T 221J J24205221 1- R 2008 CHIP RES. 220ohm 1/10W 5% RMC1/10T 221J J24205221 1- R 2009 CHIP RES. 10kohm 1/10W 5% RMC1/10T 103J J24205103 1-

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** DISPLAY-1 UNIT *** PCB with Components CB0382001 Printed Circuit Board FR001580B

LOT. SIDE.

LAY ADR.

Page 58

Display-1 Unit

Note:

Page 59

Circuit Diagram

Display-2 Unit

Page 60

Display-2 Unit

16153211817411

1013128657

D2E2F2

Dig.1

Dig.2

Parts Layout

Side A

DN8657S (Q3001)

XN1213 (9L) (Q3002)

DTC124EK (25) (Q3003)

9 1

D.P1D.P2

C2 E2

B2 F2

10 18

C1 E1

B1 F1

Side B

A1 B1 C1 D1 E1 F1 G1 A2 B2 C2

DS3001 7-Segment LCD Display

Page 61

Parts List

Display-2 Unit

REF.

D 3002 DIODE 1SS355 TE-17 G2070470 1- D 3003 LED TLY211 G2090637 1- D 3004 DIODE 1SS355 TE-17 G2070470 1- D 3005 DIODE 1SS355 TE-17 G2070470 1- D 3006 LED TLG211 G2090343 1- D 3007 DIODE 1SS355 TE-17 G2070470 1- D 3008 LED TLS211 G2090704 1- DS3001 LED GL7S201J G2090488 1- JP3001 WIRE ASSY A0953+ T9206687 1- Q 3001 IC DN8657S-T1 G1092688 1- Q 3002 TRANSISTOR XN1213-(TX) G3070194 1- Q 3003 TRANSISTOR DTC124EK T146 G3070034 1- R 3001 CHIP RES. 680 1/10W 5% RMC1/10T 681J J24205681 1- R 3002 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- R 3003 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- R 3004 CHIP RES. 220 1/10W 5% RMC1/10T 221J J24205221 1- R 3005 CHIP RES. 10k 1/10W 5% RMC1/10T 103J J24205103 1-

DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** DISPLAY-2 UNIT *** PCB with Components CB0383001 Printed Circuit Board FR001590B

LOT. SIDE.

LAY ADR.

Page 62

Display-2 Unit

Note:

Page 63

Circuit Diagram

VR Unit

Parts Layout

Side A Side B

Parts List

REF. DESCRIPTION

PCB with Components CB0384001 Printed Circuit Board FR001600B

VR4001 POT. RK0971111 10KB/SW J60800228 1-

VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** VR UNIT ***

LOT. SIDE.

LAY ADR.

Page 64

MIC Unit

Circuit Diagram

Parts Layout

Side A Side B

Parts List

REF. DESCRIPTION VALUE WV TOL. VXSTD P/NMFR’S DESIG VERS.

*** MIC UNIT *** PCB with Components CB0385001 Printed Circuit Board FR001600B

D 5001 DIODE 1SS355 TE-17 G2070470 1- J 5001 CONNECTOR R41-2509H P1090714 1- JP5001 WIRE ASSY A0953+ T9206688 1-

LOT. SIDE.

LAY ADR.

Page 65

E095490

No portion of this manual

may be reproduced

VERTEX STANDARD CO., LTD.

without the ermission of

VERTEX STANDARD CO., LTD.

Vertex VX-2000U Service manual

Introduction

Contents

Operating Manual Reprint

CONTROLS & CONNECTORS

REAR (Heatsink)

OPERATION

USER PROGRAMMABLE CHANNEL SELECTIONS

OPTIONAL ACCESSORIES

J1003 DSUB 9-Pin Data Connector Pin Assignment

Specifications

General

Receiver

Transmitter

Exploded View & Miscellaneous Parts

Block Diagram

Interconnection Diagram

Circuit Description

Receive Signal Path

Transmit Signal Path

Automatic Transmitter Power Control

Transmit Inhibit

Spurious Suppression

PLL Frequency Synthesizer

Push-To-Talk (PTT) Transmit Activation

Channel Selection & Display

Alignment

Required Test Equipment

Alignment Preparation & Precautions

Transmitter Output Power

Transmitter Deviation

PLL Reference Frequency

Receiver Squelch Threshold

Restore Original Channel Data

Side A

Side B

Side A

Side B

Side A

Side B

Side A

Side B

Parts List

Circuit Diagram

Display-1 Unit

Parts Layout

Side A

Side B

Parts List

Circuit Diagram

Display-2 Unit

Parts Layout

Side A

Side B

Parts List

Circuit Diagram

VR Unit

Parts Layout

Side A Side B

Parts List

MIC Unit

Circuit Diagram

Parts Layout

Side A Side B

Parts List