versa climber 108 LX, 108 LXP, 108 ALX, 108 ALXP Operational Manual

108 LX/LXP(ALX, ALXP) Operational Manual

108 LX/LXP (ALX, ALXP)

108 LX Series VersaClimber

(LXP, ALX, ALXP)

ASSEMBLY AND OPERATIONAL MANUAL

1.800.237.2271 | 714.850.9716 | Fax: [phone] | www.versaclimber.com | [e-mail]

Heart Rate Inc. 3190-E Airport Loop, Costa Mesa, California 92626 The VersaClimber is manufactured in the USA by Heart Rate Inc.

© 2007 Heart Rate Inc. All Rights Reserved. Made in USA

ASSEMBLY AND OPERATION MANUAL

FOR ALL LX SERIES VERSACLIMBERS

TABLE OF CONTENTS

GENERAL INTRODUCTION................................................................................................1

CALORIE BURN RATES ....................................................................................................2

STEPPING USER GUIDE ....................................................................................................3

CLIMBING USER GUIDE ....................................................................................................4

MODULE DISPLAY ..............................................................................................................5

HEART RATE MONITORING ........................................................................................6 - 7

PROGRAM LEVEL CHART ................................................................................................8

DETAILED USER GUIDE ............................................................................................9 - 10

SELECTING STEP HEIGHT ..............................................................................................11

SELECTING SPEED/TIME ................................................................................................12

USING VARIBALE CONTROL RESISTANCE ..................................................................13

SEAT/PEDALING USER GUIDE ......................................................................................14

USER GUIDE FOR AEROBIC & POWER CONDITIONING......................................15 - 17

STANDARD VS. CROSS CRAWL PATTERN....................................................................18

INTERVAL SPRINT TRAINING ..................................................................................19 - 21

USING THE VERSACLIMBER WITH MINOR INJURIES ..........................................22 - 23

UNPACKING INSTRUCTIONS ..........................................................................................24

ASSEMBLY INSTRUCTIONS - SINGLE MACHINE ..................................................25 - 29

ASSEMBLY INSTRUCTIONS - HI-TRI AND HIGH FIVE ..................................................30

MAINTENANCE SCHEDULE ....................................................................................31 - 34

TROUBLE SHOOTING GUIDE ..........................................................................................35

VERSACLIMBER SPECIFICATIONS ................................................................................36

SPARE PARTS LIST ..................................................................................................37 - 38

WARRANTY................................................................................................................38 - 39

Baby Steps. Ease into your VersaClimber workout.

Members who use stepping machines for 1/2 hour or more in my club can

only use the Versaclimber for a few minutes. Why is that?

LET’S TALK ABOUT IT!

Most stepping machines have a 12” to 14” maximum step height. The VersaClimber has a
20” maximum step height.

Most people that use stepping machines take a 5” to 8” step height, because taking longer
steps on a stepping machine is PHYSICALLY UNCOMFORTABLE. These same people take
a 15” to 20” step height on the VersaClimber, because it is PHYSICALLY MORE COMFORTABLE.

Most people lean on the hand rails of stepping machines and therefore, reduce their
gravitational body stepping weight resulting in cheating and burning less calories. The same
people cannot “cheat” on the VersaClimber because 100% of their body weight is climbing.

Members who use stepping machines at 1/2 to 1/3 the step height of a VersaClimber are
exerting 1/2 to 2/3 less energy at the same step rate. If they take the same step height and
step rate on the Versaclimber as they take on a stepping machine, they can exercise for the
same length of time on either machine. Or, if they take a longer step on stepping machines
than on the VersaClimber, they will be able to VersaClimb longer than they can step.

Most people exercise at a repetition rate of about 120 steps per minute because it is a
common aerobic music dance beat, cycling and running frequency. Most people climb 120
steps per minute or faster on the Versaclimber. If you VersaClimb at the same rate that you
step on stepping machines, but at DOUBLE or TRIPLE the step height, your workout
intensity is DOUBLED or TRIPLED making it uncomfortable and more demanding.

SO WHAT’S THE ANSWER?

Begin the VersaClimber workout with both feet at the same level. People that can step for
1/2 hour or more can also climb for 1/2 hour or more, IF THEY WORKOUT AT THE SAME

INTENSITY–achieved by simply reducing the step height on the VersaClimber.

DO YOUR MEMBERS A FAVOR!

Teach them to take a slow 5” to 8” step height, like they do on stepping machines. They will
then be able to enjoy a long and satisfying total body exercise on the VersaClimber.

WARNING

BEFORE UNPACKING, ASSEMBLING, OR EXERCISING ON THE VERSACLIMBER, READ
THIS OPERATION MANUAL THOROUGHLY. INSTRUCT OTHERS HOW TO USE THE
MACHINE IN ACCORDANCE WITH THE PROCEDURES OUTLINED IN THIS MANUAL.
ADDITIONAL MANUALS ARE AVAILABLE UPON REQUEST FROM HEART RATE, INC.
BEFORE BEGINNING THIS OR ANY OTHER EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR THOSE INDIVIDUALS OVER THE
AGE OF 30 AND THOSE WHO HAVE KNOWN HEALTH PROBLEMS. HRI ASSUMES NO
RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY
OR THROUGH THE USE OF THE VERSACLIMBER.

GENERAL INTRODUCTION

TOTAL BODY CLIMBING

The VersaClimber, introduced in 1981, was the first climbing exercise machine on the market.
It utilized one of the most natural, complete and intensive activities to which the body can be
subjected - continuous, total body, vertical climbing. This total body climbing exercise
machine provides an alternating arm and leg action against gravity with variable stroke length
and speed. All the major muscles of the arms, shoulders, back, chest, hips, buttocks and
legs are used while climbing. The VersaClimber is a proven and widely accepted, injury free,
total body exerciser that is used presently by health clubs, sports training facilities,
rehabilitation clinics, all branches of the armed forces, and professional athletes.

VersaClimber combines, in one exercise machine, the aerobic conditioning found in activities
such as: climbing, stepping, spinning, trail running, roller blading, cardio classes and cross
country skiing. It also provides the isokinetic training effects of resistance training of a pull
up, shoulder press, squat, lat pull down and military press. All of these activities are
symmetrical, recipricol and can be performed rhythmically and without orthopedic trauma.
The upper and lower body major muscle contractions maximize peripheral blood flow,
providing for higher levels of energy expenditure at lower levels of blood pressure and
perceived exertion.

A microcomputer monitors and displays the performance of the pedaling, stepping and
climbing activities. The heart rate monitor is used to guide the intensity of the workout using
heart rate as the speedometer of exercise.

NOTE:

BEGIN WITH FEET LEVEL THEN TAKE SHORT 4-6 INCH STEPS TO BEGIN. FIRST TIME
USERS OF THE VERSACLIMBER HAVE A TENDENCY TO CLIMB TOO FAST AND TO
TAKE TOO LONG A STEP. UNTIL USERS BECOME THOROUGHLY FAMILIAR WITH
THE VERSACLIMBER, IT IS MANDATORY THAT THEY TAKE SHORT, SLOW STEPS.
"LIMIT STOPS" HAVE BEEN PROVIDED TO SET THE RANGE OF MOTION BASED ON
THE ABILITY OF THE USER. FOR EXAMPLE, A MAXIMUM 6" STROKE LIMITATION
MAY BE SET FOR BEGINNERS IN THE SEATED, STEPPING, OR CLIMBING
POSITIONS.

Page 1

TYPICAL CALORIE BURN RATES

Take a moment to review the following activity comparisons. Note the difference in calorie
expenditures and speeds for various exercises. Full body climbing ranks highest in caloric
expenditure over all other activities even though speed is the slowest. Users often try to
maintain the speed that they are used to in other activities and over exert themselves due to
the total body, arm and leg movement involved in climbing at 75 degree angle. Therefore, it
is recommended that first time users of the VersaClimber begin with the feet level in the
stepping positions at a slow comfortable pace and a 4-6 inch step height.

CALORIES

ACTIVITY SPEED BURNED/MINUTE

Walking 3.0 mph 3.8
Bicycling 9.4 mph 6.4
Swimming 2.0 mph 8.1
Running 7.5 mph 13.2
Stepping 1.9 mph 14.4

Climbing 1.5 mph 16.2

1. Find your weight in the weight column

2. Find your climbing speed in feet per minute at the top of the chart

3. Read calories burned per hour in table

Page 2

STEPPING USER GUIDE

LEARN TO USE THE VERSACLIMBER AS A STEPPING MACHINE

BEFORE USING IT AS A CLIMBING MACHINE.

The hand rails not only provide support while getting on and off the VersaClimber, but also
the option of another exercise modality - Stair stepping.

1. Hold the stationary hand rails and step on the lower foot pedal.
Then, step on higher foot pedal until feet are level and stop.

2. Switch on display.

3. Turn hydraulic control knob toward "step slower."

4. Hold hand rails and take short, slow 6 inch steps for about ten minutes.

Step onto machine
by placing enough
weight on the lowest
pedal to bring it to
its bottom position.
Support the upper
body by holding
the hand rails.

Step up with
the opposite leg
and level feet.

DECREASE STEP RATE AND STEP HEIGHT FOR EASIER EXERCISE.

By holding the hand rails in the front or to the side of the body and stepping with the legs
only, the gluts, hip flexors, quads, hamstrings, calves and shins can achieve a complete
lower body aerobic and strength exercise. A variable stroke length of 1" to 20" is available.
Unlike other stair stepping machines, the foot pedal velcro straps allow the user to perform
leg lifts in the upward motion of the stroke to achieve a more effective and balanced lower
body workout. By shifting the hands from the stationary hand rails to the moving hand grips,
the machine automatically converts from a stepping machine into a total body climbing
machine or back to a stepping machine simply by changing hand position.

Page 3

NOTE:

TO MAINTAIN TRAUMA FREE MOTION, IT IS MANDATORY THAT YOU DO NOT, UNDER
ANY CIRCUMSTANCES, "BOTTOM OUT" AT THE END OF EACH STROKE. ALSO, DO
NOT HIT THE STEP HEIGHT LIMITERS WHEN THEY ARE IN USE.

CLIMBING USER GUIDE

1. Hold hand rails for support. Put foot on the lowest pedal. Apply enough weight to bring

the pedal to its lowest position. Step up with the other foot onto the higher pedal until
both feet are level.

2. With both feet at the same level, hand grips should be positioned at about shoulder
height. Adjust handles if necessary by depressing the pin at the end of the hand grip.
Remove it from its position and reinsert into hand grip adapter near shoulder height,
and release the pin.

3. Press ON/OFF button to turn on.
In Standard Mode: "Time, Rate and Distance"

10:00

STD.

854

95

information will be displayed.

4. After both feet are level, begin climbing by taking a short stroke length of approxi
mately 4" - 6" for approximately 10 minutes. "Stroke Rate" and length are deter
mined by the activity of the person climbing. After three twenty minute workouts,
the step height can be increased gradually from 4" - 6" up to a maximum of

20."

IDEAL STEP

4-6” Step Height
is the ideal step
range for those
starting out.

WHEN GRASPING THE HAND RAILS OR HAND GRIPS, KEEP FINGERS AND THUMBS
ON THE FOAM PADDING OF THE HAND RAILS OR RUBBER GRIPS OF THE HANDLES.
DO NOT GRASP OR EXTEND ANY PORTION OF THE HAND BEYOND THE FLANGES

OF THE MOVING HAND GRIPS. DO NOT HOLD ONTO THE VERTICAL POST.

WARNING

Page 4

MODULE DISPLAY

Selecting 3 modes of operation.

Standard
Mode

STANDARD MODE

1. Step on the lower pedal first. Then step
on the higher pedal until both feet are even.

2. Adjust handles at approximately shoulder

height. Press the button at end of handle
to reposition.

0:00

STD.

000

000

3. Press "ON/OFF" and the computer
defaults to the standard mode. (STD)

4. Press "ON/OFF" when finished. The display

will turn off after two minutes of inactivity.

PROGRAM MODE

1. Press "ON/OFF" and press “PROGRAM

MODE”

2. The display will ask you to “ENTER

TIME”. Keypad in a desired exercise
time and press "ENTER".

5. The object is to match your ACTUAL
FEET PER MINUTE displayed in the

upper right hand corner of the display
with the GOAL FEET PER MINUTE
located directly below.

6. You can exit the program at any time by
pressing "RESET".

7. Press "ON/OFF" when finished. The dis

play will turn off after 2 minutes of inactivity.

RACE MODE

1. Press the “RACE MODE” button.

2. The display will ask you to enter exercise

time. Keypad in total minutes and press
"ENTER".

3. The display will then say enter Total Feet
you wish to climb. Keypad in desired
feet from 0 to 9999 and press "ENTER”.
Press "START EXERCISE" and begin
your program.

Race
Mode

ENTER TIME

RACE

Program
Mode

0:00

PROG.

ENTER TIME

3. The display will ask you to enter a pro
gram from 1 through 15. Keypad in a
desired program number and press
"ENTER".

4. Press "START EXERCISE" and begin
your program.

5. The object is to exceed your OPPONENTS
FEET PER MINUTE displayed in the
lower right hand corner of the display.

6. You can exit the program by pressing

"RESET".

7. Press "ON/OFF" when finished. The dis

play will turn off after 2 minutes of inactivity.

Page 5

HEART RATE MONITORING USER GUIDE

FOR HEART RATE MODELS

The Heart Rate Monitoring mode is intended to guide the exerciser through an aerobic
exercise based on their heart rate. It is recommended to select and start with the minimum
70% of maximum age- related heart rate as suggested in this manual.

To use the Heart Rate Monitoring mode, you must wear a chest strap transmitter shown
below. The strap should be snug enough to hold electrodes securely against the skin
to prevent motion of the electrodes but should not feel uncomfortable.

HOW TO FIND YOUR

TARGET HEART RATE

Heart rate is the best indicator of exercise intensity. Use your heart rate and level of perceived
exertion (how you feel) as a guide to determine if you have selected the proper "LEVEL OF
CONDITIONING". The following HEART RATE TRAINING ZONE CHART may be used to
assist you in selecting your appropriate heart rate training zone.

1. Find your age at the bottom of the chart.

2. Beginners follow the column to 70% of
your maximum heart rate.

3. Advanced follow the column to 85% of
your maximum heart rate.

4. Exercise at your appropriate heart rate.

HEART RATE TRAINING GUIDE

Page 6

HEART RATE MODE (for LXP or ALXP models only)

Place
Adjustable
Chest Strap
Here.

Calculated
Max Heart
Rate based
on your age

Read Heart Rate Mode

1. Place the Heart Rate
Polar compatible transmitter
strap on the chest just
below the breast pectoral
muscles. Moisten the skin.

2. The strap can be moved up or down and
left to right to find the best transmission
area on the chest.

3. On the module, press "ON/OFF" and

then press "READ HEART RATE".

NOTE: Heart Rate can be read in each of the
4 modes by simply pushing the “READ
HEART RATE” button at any time.

4. Press "ENTER PERSONAL INFO".

5. Enter your age on number keypad and

press "ENTER".

6. Calculated heart rate max will be displayed.

NOTE: To change HR max number press “0”
three times and then key in a heart rate
goal.

7. Press "ENTER"

8. Press "START EXERCISE".

This number
is the % of

2:87

109

185

87

65

32

6

your Max
heart rate.
As your HR
increases so
does the %.
Ideal training
based on
60-80% of
your HR Max

9. As you begin to workout, the % Max Heart

Rate number will increase as your heart rate
rises. It is recomended to maintain a range of
60-80% of Heart Rate Max.
The module will beep to notify you when
your heart rate max as been exceeded.

Heart Rate Control Mode

With Polar compatible chest strap in place,
Press "CHANGES MODES” button and
select “HRC”

1. Press "ENTER PERSONEL INFO".

2. Enter age on number keypad and press
"ENTER".

3. Your Calculated heart rate max will be

displayed.

4. Press "ENTER" for 80% of max heart

rate or change by pressing 0 three times
and then key in a heart rate goal.

NOTE: The new Heart Rate goal (num
ber) you input will always default to an
output of 80%

5. Enter in amount of time. Press “ENTER”

6. Press "START EXERCISE".

7. Begin climbing. Match "Actual Feet Per

Minute" to "Goal Feet Per Minute"
indicated by up and down arrows. The
computer will display the proper climb
rate to keep user in the desired target
heart rate range.

8. Match the goal speed that is updated

every 30 seconds.

Your feet
per minute.

Heart Rate
Control
Mode

2:87

HRC

148

87

50

MATCH

6

51

Match this
number by
climbing
faster or
slower. This
number is
determined
by heart rate.

YOUR HEART RATE SHOULD BE USED AS A GENERAL REFERENCE FOR THE INTENSITY
LEVEL OF AN EXERCISE ACTIVITY. CONSULT A PHYSICIAN BEFORE BEGINNING THIS OR
ANY OTHER EXERCISE. IMMEDIATELY DISCONTINUE THIS OR ANY OTHER EXERCISE IF
YOU FEEL FAINT, ANY DISCOMFORT, SHORTNESS OF BREATH, OR DIZZINESS.

WARNING:

Page 7

PROGRAMMED LEVEL CHART

Minutes

PROGRAM NUMBERS

1 2 345678910111213141516

FEET PER MINUTE CLIMB RATES

10 15 20 25 30 35 40 45 55 75 95 115 135 155 175 195

15 20 25 30 35 40 45 50 60 80 100 120 140 160 180 200

20 25 30 35 40 45 50 55 70 90 110 130 150 170 190 210

25 30 35 40 45 50 55 60 80 100 120 140 160 180 200 220

30 35 40 45 50 55 60 65 85 105 125 145 165 185 205 225

25 30 35 40 45 50 55 60 80 100 120 140 160 180 200 220

30 35 40 45 50 55 60 65 90 110 130 150 170 190 210 230

35 40 45 50 55 60 65 70 100 120 140 160 180 200 220 240

25 30 35 40 45 50 55 60 85 105 125 145 165 185 205 225

30 35 40 45 50 55 60 65 90 110 130 150 170 190 210 230

35 40 45 50 55 60 65 70 100 120 140 160 180 200 220 240

40 45 50 55 60 65 70 75 110 130 150 170 190 210 230 250

30 35 40 45 50 55 60 65 105 125 145 165 185 205 225 245

35 40 45 50 55 60 65 70 110 130 150 170 190 210 230 250

45 50 55 60 65 70 75 80 100 120 140 160 180 200 220 240

30 35 40 45 50 55 60 65 90 110 130 150 170 190 210 230

35 40 45 50 55 60 65 70 100 120 140 160 180 200 220 240

40 45 50 55 60 65 70 75 110 130 150 170 190 210 230 250

35 40 45 50 55 60 65 70 100 120 140 160 180 200 220 240

30 35 40 45 50 55 60 65 105 125 145 165 185 205 225 245

35 40 45 50 55 60 65 70 100 120 140 160 180 200 220 240

40 45 50 55 60 65 70 75 110 130 150 170 190 210 230 250

30 35 40 45 50 55 60 65 105 125 145 165 185 205 225 245

35 40 45 50 55 60 65 70 110 130 150 170 190 210 230 250

45 50 55 60 65 70 75 80 100 120 140 160 180 200 220 240

30 35 40 45 50 55 60 65 90 110 130 150 170 190 210 230

35 40 45 50 55 60 65 70 100 120 140 160 180 200 220 240

40 45 50 55 60 65 70 75 110 130 150 170 190 210 230 250

35 40 45 50 55 60 65 70 100 120 140 160 180 200 220 240

30 35 40 45 50 55 60 65 105 125 145 165 185 205 225 245

35 40 45 50 55 60 65 70 100 120 140 160 180 200 220 240

32 37 42 47 52 57 62 67 95 115 135 155 175 195 215 235

Beginner Average Advanced Elite

0-1

1-2

2-3

3-4

4-5

5-6

6-7

7-8

8-9

9-10

10-11

11-12

12-13

13-14

14-15

15-16

16-17

17-18

18-19

19-20

20-21

21-22

22-23

23-24

24-25

25-26

26-27

27-28

28-29

29-30

30-31

FEET

FEET

FEET

FEET

AVERAGE FEET PER MINUTE

AVERAGE FEET PER MINUTE

AVERAGE FEET PER MINUTE

AVERAGE FEET PER MINUTE

Pro g ram Lev e l Char t

There are four major Program workout levels. Beginner 1-4, Average 5-7, Advanced 8-11
and Elite 12-16. Select a Program level when prompted by the display module based on
your level of fitness. Increase or decrease the level to fit your needs. All Programs have
built in warm up and warm down. The warm up is shown on the chart but the warm down is
not shown.

Select an exercise time when prompted by the display module. When you select an exercise
time, remember that the program includes a 5 minute warm down (not shown on the chart).
For example if you choose Program Level 5 and a 10 minute workout time you will climb for
1 minute at 30, 35, 40, 45, and 50 feet per minute and for 5 more minutes at a deceasing
speed for a total of 10 minutes. If you choose to workout without the warm down included,

add an extra 5 minutes to the time entered.

Page 8

DETAILED USERS GUIDE

1. STEPPING ON - Hold the hand rails for support. Put the foot on the lowest pedal
(photo 1) Apply enough weight to bring the pedal to its lowest position. Step up with the
other foot (photo 2) onto the higher pedal stepping up until both feet are level (photo 3)
This is the starting position.

Photo 1 Photo 2 Photo 3

2. HANDLE SELECTION - The VersaClimber is supplied with one pair of straight quick
release handles. To adjust the handles, simply depress the pin at the end of each handle
and remove it from its position. Reinsert the handle into the adaptor closest to the shoulder
height of user and release the pin.

3. Begin climbing, taking a short 2 to 4 inch step as shown below.

WHEN GRASPING THE HAND RAILS OR HAND GRIPS, KEEP FINGERS AND THUMBS
ON THE FOAM PADDING OF THE HAND RAILS OR RUBBER GRIPS OF THE HANDLES.
DO NOT GRASP OR EXTEND ANY PORTION OF THE HAND BEYOND THE FLANGES
OF THE HAND GRIPS. DO NOT HOLD ONTO THE MAIN VERTICAL POST.

Page 9

4. CLIMB RATE & STROKE LENGTH - Climb rate and stroke length are determined strictly
by the activity of the user. The user may take a stroke as short as 2 or 3 inches or as long
as the machines movement allows. To maintain a shock and trauma-free motion, do not
bottom out at the end of each stroke. The stroke rate can be maintained at a steady pace
by using the beat of music and/or maintaining a specific stroke length, steps or feet per
minute as indicated on the computer.

TO MAINTAIN A SHOCK AND TRAUMA FREE MOTION IT IS MANDATORY THAT YOU
DO NOT, UNDER ANY CIRCUMSTANCES, "BOTTOM OUT" AT THE END OF EACH
STROKE. ALSO, DO NOT HIT THE STEP HEIGHT LIMITERS WHEN THEY ARE IN USE.

5. HYDRAULIC CONTROL- The rate of motion or climbing speed can be controlled
hydraulically. The user, therefore, can simultaneously exert
upward and downward forces by pushing and pulling with
arms and legs against selected rates of motion. This
results in more agonist and antagonist gross muscle mass
contraction than on any other exercise machine. Faster
step rates are selected for aerobic exercise and slower step
rates are selected for low level aerobic and isokinetic
muscle strength, power and endurance training.

Select rate of motion, (faster/slower) by rotating hydraulic
control knob, when rate of motion is selected, any forces
applied by the person (pedaling, stepping or climbing), will be
resisted by the hydraulics set at that rate. Upper body or

lower body exercises can be performed fast or slow depending on the rate of motion selected
with the hydraulics.

Perform aerobic exercises with the hydraulics set to a minimum. To set hydraulics to a
minimum (increase rate of motion), turn the hydraulic control knob fully counter clockwise. To
slow the rate of motion, turn the hydraulic control knob in a clockwise rotation. The rate of
motion may be changed without stopping any time during exercise.

6. MODULE DISPLAY SYSTEM - The LX model VersaClimber has three modes of operation.

Standard, Program and Race.

Page 10

SELECTING STEP HEIGHT

START SLOW AND TAKE SHORT STEPS!

USE THE VERSACLIMBER AS A STEPPER FIRST.

To begin,
level feet

No matter what level of conditioning you are at, start slow and take a 4" to 6" step height.
Only take a step or stroke length that feels comfortable. Do not take long steps or you will
tire quickly!

Although a step height of up to 20 inches is available, it is not necessary to take the maximum
stroke length to receive cardiovascular and strength benefits.

To ensure that users maintain a short stroke length, range of motion limiters have been
provided for each machine. These "stops" can be set in the pedaling, stepping or climbing
positions and are designed for safe, controlled workout routines. They are easily installed
and adjustable to 6 different range limitations.

Beginners
should not
exceed a 4-6”
step height

Conditioned
users can
choose to
step15”-20”

RANGE OF MOTION (Optional Upgrade)

Limiter Bolt

(Optional Upgrade)

Limits step range of

motion.

The range of motion "limiters” or “stops”, are located on the slide bar inside the
track just above each left and right pedal. Extra holes have been threaded into
the slide bar to allow the limiters to be adjusted up or down in 2 inch increments.

To decrease the range of motion, remove both limiters from their lowest position.
Level pedals and re-install the limiters to a higher position (e.g. three holes
down). Both left and right limiters should be in the same position on both sides.

Hold the stationary hand rails to the front or side of the body and begin stepping.
Notice the limiters restrict the step height. Take short steps up to the stroke
length the limiters will allow. Do not bottom out or hit the limiters against the
frame. Do not over exert yourself. Step rate should be easy enough so that a
minimum exercise of 10 minutes can be achieved.

Page 11

SELECTING SPEED

Climbing uses many more muscles than jogging, pedaling or stepping and is therefore
performed at a much lower cyclic rate. The "Feet Per Minute" rate indication is the most
meaningful guide for the amount of work being done.

To determine speed or rate at which you are stepping, put the toggle switch in the up
position to display "Feet Per Minute." A reasonable rate for a 25 to 35 year old person in
good condition would be about 60 feet per minute. After 3 to 5 minutes of exercise, pulse
rate should be checked and the climbing rate adjusted appropriately to bring the user to their
target heart rate zone. Climbing at about 50 feet per minute would provide the equivalent
work load of running a 10 minute mile, while 80 feet per minute would be closer to an 8
minute mile. Similarly, exercise level 7 on a stationary bike is roughly equivalent to 70 feet
per minute on the VersaClimber. Exercise level 10 is roughly equivalent to 100 feet per
minute on the VersaClimber set at minimum resistance.

If your weight exceeds 240 pounds, divide your weight in half and follow the above 3 steps.
Double the calories per hour figure to get your total calorie burn rate based on your climbing
speed (feet per minute) and weight.

For most people losing weight it is often very difficult. It requires discipline in your eating
habits as well as participating in a regular exercise program. The objective to losing weight
is to consume less and exercise more, thereby expending calories that would normally be
stored in the body as fat. For example. 3,500 calories equals 1 pound of fat. If you eat 3,500
calories in a single day and expend 1,750 calories as energy (including walking, exercising,
breathing etc.) you would gain a 1/2 pound of fat. Over a one week period, by consuming
3,500 calories each day and converting only half the calories into energy, you would gain 3
1/2 pounds. Remember, to lose weight you need to decrease your calorie intake and
increase your physical activity. Elite athletes often eat thousands of calories each day to
maintain their body weight due to their high and frequent exercise activity.

SELECTING EXERCISE TIME

A warm up period of at least 5 to 10 minutes should always be included in each VersaClimber
workout. The first time user can climb for 15 minutes by including a 5 minute warm up and a
3 to 5 minute warm down period. Taking a short step at a slow climbing speed during the
warm up period is the key to a great workout. With repetitive use, it is possible to build up to
longer exercise times and higher rates.

Many individuals enjoy 60 or more minutes of uninterrupted climbing. At the end of climbing,
note your time and distance readings for establishing a goal for future sessions. Always use
pulse rate and perceived exertion to determine if you are at a comfortable exercise level.
Remember that work intensity is based on climbing speed. Climb at a faster or slower "Feet
Per Minute" speed to increase or decrease your work intensity.

Page 12

USING HYDRAULICS TO SELECT THE RATE OF MOTION

Beginners and individuals who are deconditioned may use the hydraulics to control the rate
of motion or speed of the exercise. The hydraulic control knob is located at the bottom of the
control console. Clockwise rotation of the control knob, (to the right), slows the rate of
motion. Counter-clockwise rotation of the control knob, (to the left), increases the rate of
motion. The rate of motion, (slower/faster), may be changed without stopping any time during
exercise. Start with the speed control knob fully rotated clockwise and gradually increase the
climb rate to the desired speed by turning the control knob in the counter-clockwise direction.

NOTE:

ALX models are
fixed resistance
and do not feature
a variable tension
control knob.

To use the hydraulic control as a low level exercise, turn the hydraulic control knob fully in
the clockwise direction. Transfer weight from one foot to the other to cause the machine to
move at the slow preset rate. Then, gradually turn the knob to climb at the desired speed.
Do not try to push or pull the foot pedals or hand grips to cause the machine to move faster
then it does by weight transference. Once again, take strokes that are comfortable.
Common rates in this mode are between 20 and 30 feet per minute.

STAIR STEPPING

The VersaClimber provides the ability to perform variable height and variable speed stair
stepping exercises for the lower body only. The hand rails, located about waist high, are
used to grasp and thus stabilize the upper body while stepping with the legs only. The upper
body is maintained in an erect stationary position while the legs and hips perform a lower
body stepping exercise. The foot straps also allow the user to perform a leg lift exercise while
stepping, not available on single purpose stepping machines.

By holding the hand rails in front of you or to the side of your body and stepping with legs
only, the buttocks, front and back of the thighs, calves, and shins can achieve a complete
lower body aerobic and strength workout. Stair stepping is recommended for beginners
before they attempt a full body climbing exercise and can be performed in any mode of operation.
Heart rate can be increased or decreased while stepping by increasing or decreasing step
rate and stroke length.

Set the rate of motion desired with the hydraulic control knob. To perform a leg lift exercise,
use the stirrups and lift with one leg while stepping down with the other leg and alternate.

Page 13

SEAT/PEDALING USER GUIDE

The seat option provides both a seated legs only exercise and a seated arm and leg
exercise. Unlike bicycles, the stroke length is variable from 1" to 20", and the feet can push
and pull for a complete leg exercise. By grasping the moving hand grips, the arms, chest
and back muscles can be added to the leg muscle activity. The seated exercise is primarily
for a warm up and low to medium exercise level.

THE SEAT OPTION PROVIDES THREE ADDITIONAL EXERCISES.

1. Pedal With Legs. Pedal with the legs only in the seated position while
holding the stationary hand rails for upper body support.

2. Push And Pull With Arms. Grasp the moving hand grips and push and
pull with arms only, allowing the legs to move passively.

3. Exercise Arms And Legs. Pedal with the legs while pushing and
pulling with the arms.

The seat transforms the machine into a pedaler, plus a pedaler with upper body exercise. To
accommodate differences in limb lengths, it may be necessary to lower the hand grips and
adjust the seat horizontally and vertically. Beginners can perform a legs-only exercise
comfortably by pushing and pulling with the feet. While bicycles have fixed range of motion,
stroke length on the VersaClimber is controlled by the user from 1" to 20" through a complete
range of pedaling rates. By grasping the moving hand grips, the muscles of the arms,
shoulders, chest and back are added to the leg muscle activity. The seated exercise is for
warming up and low to medium level exercises.

SEAT ADJUSTMENT

The seat assembly easily attaches to the VersaClimber by fully inserting a pin through two
holes in the mainframe of the VersaClimber and one of the holes in the seat assembly.

This comfortable bicycle seat is adjustable vertically with the pin and horizontally with a knob
located under the seat. The vertical seat adjustment is for differences in leg lengths while the
horizontal adjustment accounts for differences in arm lengths.

NOTE:
THE SEAT ASSEMBLY WEIGHS 8 POUNDS. IF YOU ARE UNABLE TO SUPPORT THE
WEIGHT OF THE SEAT FIRMLY IN ONE HAND, DO NOT ATTEMPT VERTICAL
ADJUSTMENT OF THE SEAT WITHOUT ASSISTANCE. DO NOT ATTEMPT SEAT
ADJUSTMENT WHILE STANDING ON FOOT PEDALS OR WHILE SEATED.

Page 14

USER GUIDE FOR AEROBIC CONDITIONING

NOTE:
REGARDLESS OF YOUR FITNESS LEVEL, THERE IS A STEP HEIGHT AND
CLIMBING SPEED THAT CAN BE MAINTAINED FOR A MINIMUM OF 15 MINUTES.

The VersaClimber has the capability of providing an aerobic exercise which is superior to
other types of aerobic exercise. Like swimming or cross country skiing, climbing involves
both arms and both legs.

The following guidelines are provided to acquaint the first time user to aerobic exercise on
the climber.

IF YOU CLIMB A MOUNTAIN "TOO FAST" YOU CAN ONLY

CLIMB FOR A FEW MINUTES–TAKE YOUR TIME.

*All calculations are based on hydraulics set at minimum.

LEVEL OF CONDITIONING CLIMB EXERCISE DISTANCE STEP

RATE TIME CLIMBED HGHT

(Estimated) (feet/min) (min) (feet) (inches)

1. OUT OF SHAPE BEGINNER 20 3 - 10 60 - 200 3 - 5

2. BEGINNER 25 4 - 15 100 - 375 4 - 6

3. NOVICE 35 5 - 20 175 - 700 4 - 7

4. WEEKEND ATHLETE 50 7 - 20 350 - 1000 5 - 8

5. FAIR CONDITION 60 8 - 20 480 - 1200 5 - 9

6. GOOD CONDITION 80 10 - 20 800 - 1600 6 - 10

7. VERY GOOD CONDITION 100 12 - 20 1200 - 2000 7 - 12

8. EXCELLENT CONDITION 115 14 - 20 1610 - 2300 8 - 16

9. ELITE CLIMBER 125 16 - 20 2000 - 2500 8 - 18

10. KING OF THE MOUNTAIN 145 18 - 20 2610 - 2900 8 - 18

To use the chart, first select the "LEVEL OF CONDITIONING" that best describes you.
Suppose the level you have selected was the (WEEKEND ATHLETE). Use the data shown
in line (4) for the (WEEKEND ATHLETE). For your first workout on the VersaClimber, choose
the lowest number in each section of the chart at your estimated "LEVEL OF
CONDITIONING".

Page 15

STRENGTH TRAINING

The VersaClimber can be used to develop strength, power and endurance for all of the major
muscles of the body. The VersaClimber hydraulic control system provides an ISOKINETIC
exercise. ISO: equal; similar. KINETIC: of or provided by motion. The term ISOKINETICS
when applied to EXERCISE indicates that THE EXERCISE IS PERFORMED AT THE SAME
RATE OF MOTION REGARDLESS OF THE AMOUNT OF FORCE EXERTED. More simply,
when the rate of motion is selected, any forces applied by the person pedaling, stepping or
climbing, high or low, will be resisted by the hydraulics, at that same pre-selected rate or
speed.

STRENGTH

To develop full body strength, set the hydraulics to a slow rate of motion. Rotate control knob
to the right (clockwise) until the desired slow rate of motion is obtained and perform 8 to 12
slow repetitions, Push and pull with both arms and legs in the upward and downward
directions.

POWER

To develop power, set the hydraulics to a faster rate of motion. Rotate control knob to the left
(counterclockwise) until the desired speed is obtained and perform 15 to 30 fast repetitions.
Push and pull with both arms and legs in the upward and downward directions.

ENDURANCE

To develop endurance, set the hydraulics at intermediate rates of motion and pedal step or
climb for extended periods of time, (30 minutes or more).

TYPES OF RESISTANCE EXERCISES

With the hydraulic control properly adjusted, the VersaClimber has the capability of providing
various strength conditioning exercises. A lat pull, chin up, military/shoulder press, squat, leg
press, and leg lift can all be implemented.

UPPER BODY EXERCISE

The arms, shoulders, chest and back can be isolated by standing on the base plate in front
of the VersaClimber and pushing and pulling the moving handles. Position the handles so
that they are within reach when the arms are fully extended. Select the desired rate of motion
with the hydraulic control knob. With your hands in the start position (palms facing away from
you), concentrate on pulling down right then left with your latissimus dorsi (side of
back), posterior fibers of deltoids, (back of shoulders) and the triceps brachaii (back of arm).
This flexion on one side of the body with extension of the other side of the body will tone and
trim your sides, stomach, back and back of arms.

To isolate more chest, (pectoralis group), biceps brachaii (front of arms), anterior deltoids
(front of shoulders) and stomach (abdominals) perform the same pulling action with a reverse
grip (palms facing you). Both sets of muscle groups, front and back, can be worked by
simultaneously pushing and pulling right and left. During this upper body only activity, a full
range of cyclic rates and stroke lengths can be selected.

Page 16

LEG LIFTS AND QUAD, HAMSTRING

AND GLUTE SUPER SETS

For isolated leg lifts and leg presses, adjust the velcro foot straps to fit snug on the feet. Set
the rate of motion with the hydraulic control knob. Grasp the hand rails to anchor the upper
body. Maintain the foot in horizontal position while lifting against the foot straps. Perform the
desired activity then recover as you would between intervals. See Interval Training, Page

For the advanced athlete, a "quad burn" can be achieved by squatting down (while holding
the stationary hand rails) and performing a stepping exercise. Use the foot straps to secure
the feet on the pedals and bend the knees until the thighs are approximately horizontal and
the knees straddle the machine. Start with short steps, pushing down with one leg while
lifting up with the other. Maintain the body weight within the base of the machine. Step in the
squat position until quads "burn out" or quad fatigue occurs. This exercise can also be performed
as an interval workout set.

Quad burn. Squat down, straddle
knees until thighs are horizontal.
Push and pull with legs while
maintaining crouched position.

Foot Positioning

The position of the foot or feet on the pedals will allow the focus of the work to be in a
concentrated area of the muscle or muscles. If tingling or numbness occurs, reposition
the foot on the pedal (forward or back) until you are comfortable.

To concentrate the work on your ankle and calves. Climb on your toes. Quad work can be
accentuated by climbing with the heel of the foot forward on the pedal. The intensity of the
work for the inner legs can be increased by pointing the toes inward. Turning the toes outward
will work the outer legs.

Page 17

CROSS BODY, SAME SIDE, AND FULL BODY SETS

CLIMBING VS. RUNNING MOTION

All Institutional VersaClimber Models, with the exception of models designated with "CC" for
cross crawl or running motion, and the Clinical Model CL-108C have been designed with the
standard "climbing motion". A "climbing motion" is produced, as the hand and foot on the
same side of the body move in an upward direction, while the opposite arm and leg move in
the downward direction.

Standard Pattern
Elbow & Knee move
in the same direction
maintaining equal
distance apart

Cross Crawl
Elbow & Knee
meet together on
the same side

The "cross-crawl" or "running motion" provide a unique alternative to the standard "climbing
motion". A "running motion" is produced as the arm and leg approach each other on one side
of body while the opposite arm and leg separate on the other side.

CROSS BODY AND SAME SIDE STRENGTH SETS

CLIMBING MOTION

To perform "cross body" strength sets, adjust the hydraulics to the appropriate speed and
tighten the foot straps. Climb using cross body forces by pulling down with the arm on one
side of the body and lifting with the leg on the other side of the body. Move as though you
were going to touch the elbow of the right arm to the opposite knee of the left leg as they
come together. Then alternate.

To perform an alternate cross body strength set, push up with the left arm and down with the
right leg. Alternate by pushing up with the right arm and down with the left leg.

RUNNING MOTION

To perform "same side" strength sets, adjust the hydraulics to the appropriate speed and
tighten the foot straps. Climb using the forces on the same side of the body by pulling down
with the arm and lifting up with the leg. Move as though you were going to touch the elbow
of right arm to the right knee on the same side of the body. The left arm and knee on the
opposite side of the body will separate. Alternate this pulling motion.

To perform an alternate "same side" body strength set, concentrate on pushing up with the
right arm and down with the right leg on the same side of the body. Move as though you are

Page 18

trying to push the elbow and the knee away from each other on the same side of the body.
The left arm and leg on the opposite side of the body will come together. Alternate this

pushing motion.

FULL BODY SETS

CLIMBING and RUNNING MOTIONS To perform full body strength sets, adjust the

hydraulics to the desired speed and secure the foot straps. Exert upward and downward
forces with the arms and simultaneously exert upward and downward forces with the legs.
This activity is equivalent to a lat pull and military press for the upper body and a leg press
and weighted lift for the lower body.

INTERVAL TRAINING

Interval training on the VersaClimber is for advanced level workouts. User's should be
thoroughly familiar with all functions of the VersaClimber and be able to comfortably climb a
minimum of 30 minutes per workout session before attempting this method of conditioning.

Interval training is for the advanced person who wants to increase their aerobic and anaerobic
capacity. The purpose of interval training is to increase the intensity of the workload for a short
period of time so that the oxygen supplied to the muscles is less than the amount of oxygen
required to maintain the workload. An oxygen debt is created in the muscles and therefore
they must work anaerobically or without oxygen for a short period of time. The intense portion
of the interval is then followed by a short, low intensity, recovery period.

Intervals on the VersaClimber are achieved by sprinting, that is, by increasing the speed and
the stroke length of each step (faster rates of motion) or by exerting maximal forces against
a preset rate of motion (slower rates of motion). Both of these methods of interval training
condition the cardiovascular system to become used to extremely strenuous work loads.

AEROBIC INTERVAL TRAINING

Sprint intervals consist of short sprints (hydraulic control set to a minimum) of 5 - 15 seconds
with both arms and legs pushing and pulling in the upward and downward directions (full
body sets). Motion should be as quick as possible until the anaerobic threshold (not to
exceed 85% of predicted maximal heart rate) is achieved. The foot straps should also be
used for vertical lift. The upper torso should remain stable during the sprint interval to ensure
unwasted motion. The interval should be followed by a recovery period of 2 - 3 minutes or
until breathing is controlled and muscle fatigue has diminished. Repeat. As you become better
conditioned, the rest time between each interval should become shorter.

Remember to always warm up 10 - 15 minutes on the VersaClimber before beginning interval
workouts and to always stay within your target heart rate. It is also very important to always
continue climbing during recovery periods at a slow, easy pace taking a 2 - 4 inch step. The
following aerobic-anaerobic training chart is a general guideline for advanced interval training on the
VersaClimber. This advanced training technique is not for beginners or for those who have
health problems.

Page 19

Time/Min Exercise Description % of Max HR

0 - 10 min Warm Up To Aerobic Rate Resting To 60-75%

10 - 20 min Aerobic-Anaerobic Interval

Training Period:
Interval: Exert maximal power (Force
and Speed) against a restricted rate of
motion set by the hydraulic knob.
Push and pull with both arms and legs
for 8-12 strokes on each side through a
full range of motion. Do not bottom out.
Restricted rate of motion should be set to
allow user to complete the 8-12 strokes and
not exceed the upper percentages of maximal
heart rate. After power strokes have been com­pleted, relax and take a shorter, slower step
until heart rate returns to lower aerobic recovery
level. Start next interval. Complete as many
as possible during the interval time limits.

Exercise Variations:
#1 Forehand Grip, Push and Pull Arms and Legs 80 - 85%
Aerobic Recovery - Short Slow Steps. 60 - 65%

#2 Stationary Hand Rails, Legs Only, Push and Pull 80 - 85%
Aerobic Recovery - Short Slow Steps. 60 - 65%

#3 Reverse Grip, Pull Down Arm, Pull Up Leg, Cross Body 80 - 85%
Aerobic Recovery - Short Slow Steps. 60 - 65%

#4 Forehand Grip Push Up Arm, Push Down Leg, Cross Body 80 - 85%
Aerobic Recovery - Short Slow Steps. 60 - 65%

#5 Forehand Grip, Push and Pull Arms and Legs 80 - 85%
Aerobic Recovery - Short Slow Steps. 60 - 65%

#6 Stationary Hand Rails, Legs Only, Push And Pull 80 - 85%
Aerobic Recovery - Short Slow Steps. 60 - 65%

#7 Reverse Grip, Pull Down Arm, Pull Up Leg, 80 - 85%
Aerobic Recovery - Short Slow Steps. 60 - 65%

#8 Forehand Grip, Push and Pull, Arms and Legs 80 - 85%

20 - 30 min. Aerobic Speed Work

30 - 35 min. Warm Down 70 - 75%

(Hydraulic Control Set To Minimum) 60 - 65%

Page 20

STRENGTH INTERVAL TRAINING

Strength intervals are achieved in a similar manner to aerobic interval training, except the
intervals are performed at a slow rate of motion. First, turn the hydraulic control knob located
at the bottom of the console in the clockwise direction, to approximately 75% of the user’s
capability. Begin climbing, exerting a maximum effort by pushing and pulling with arms and
legs in the upward and downward direction for 5 to 10 seconds or until muscles are almost
fatigued and anaerobic threshold is met (not to exceed 85% of your predicted maximal heart
rate). Be sure to use the foot straps to maximize the vertical lift. Hands may be in the forward
or reverse grip position depending on the desired muscle groups to be worked. Recover from
the interval by setting the hydraulic control to a minimum (counter-clockwise direction) and
taking short, slow, 2 to 4 inch strokes until breathing is controlled and muscles have recovered.
As previously mentioned, as you become better conditioned, the rest period between each
interval will become shorter.

1. Warm-up 10-15 minutes on the VersaClimber before beginning interval workouts.

2. Always stay within your target heart rate.

3. Continue climbing during the recovery periods.

USING THE VERSACLIMBER WITH MINOR INJURIES

MOST MINOR INJURIES THAT PREVENT RUNNING,

DO NOT PREVENT CLIMBING

You must always use common sense when exercising. If you have an injury that hurts when
you walk or run, it is common sense to stop walking or stop running. If the injury hurts while
climbing, do it easier or do it slower. If it continues to hurt...stop! Consult with your doctor
about any injury prior to engaging in an exercise program.

Some leg, knee, arm, chest, shoulder and back injuries can be safely exercised on the
VersaClimber by limiting the range of motion or isolating the motion of the injured body part
on one or both sides of the body. The smooth, rhythmic, impact free motion will decrease
the likeliness of further assault to the injured limb while maintaining or increasing
cardiovascular and muscular fitness.

The VersaClimber eliminates all pounding trauma and provides biofeedback information to
the user to monitor step heights and step rates. It is ideal for controlled upper and lower body
activity for fitness maintenance during the recovery phase of minor injuries.

LEG INJURIES

The VersaClimber eliminates pounding and jarring of the joints and can therefore be used to
exercise such injuries as hamstring pulls, knee injuries, shin splints, achilles pulls, turf toe,
leg bruises and sprains. By controlling the rate of climb, the range of motion, and/or by
repositioning the foot or feet on the pedal(s), specific areas of the leg and foot may be
exercised passively.

Page 21

IMMOBILIZATION OF THE LOWER BODY

If the lower body must be completely immobilized due to injury, you can still strengthen your
upper body and maintain cardiovascular fitness by doing an arms only workout on the
VersaClimber. Stand on the base plate with one foot on each side of the post. Select or
reposition the hand grips so that when one arm is outstretched it is fully extended. Alternate
the pushing and pulling motion of the arms while the lower body remains still.

UPPER BODY INJURIES

The arms, chest and shoulders can be totally or partially immobilized while climbing by
placing one or both hands on the stationary hand rails. If upper body limb motion is
desirable without active muscle contraction, the injured arm can be placed on the moving
hand grip and moved passively, without pushing or pulling.

BACK INJURIES

Exercise that causes back or neck discomfort is frequently the result of either vertical
compression loading of the vertebrae or a shearing or bending of the spinal column and back
muscles. By keeping the back straight while climbing, with the hydraulic control knob set to
a minimum, the discomfort of the injury is minimized. The vertebrae are kept in line rather
than being sheared, bent or compressed like with many other conventional exercises. To
perform strength workouts, lift with the legs and pull with the arms. These forces tend to
elongate the body and stretch the spinal column and provide an otherwise unattainable high
level full body workout, without neck or back discomfort. If the lower back injury is such that
it cannot be moved at all, you can still exercise the upper body by doing an upper body
workout only. If the injury is in the cervical or thoracic areas, (lower or upper spine) one can
utilize the VersaClimber by grasping onto the stationary hand rails and simply using the legs
only.

The seat provides an easy sit down routine for beginners and a safe exercise for those who
require a non-weight bearing type of activity. Push and pull with any combination of healthy
arms and legs to assist the movement of the injured limb or limbs. It is also possible to
completely isolate one or both arms or one or both legs while in the non-weight bearing seated
position. Set the hydraulic speed control and range of motion limiters to accommodate the
injury. The heart rate control mode can also be used to regulate work intensity of the
seated arm and leg exercise.

FOR ZERO RANGE OF MOTION IN KNEE

The VersaClimber can be used for aerobic and strength training by a person in a brace or a
thigh to ankle weight bearing cast that can not bend at the knee. Workouts to maximal heart
rates and maximal forces can be performed with one totally immobile leg while it may be
necessary to walk up to and away from the machine using a crutch or cane.

SEATED EXERCISES

Page 22

To exercise, set the range of motion limiter on the same side as the injured leg, so the range
of motion in the injured joint is limited. Place the injured leg on the lower foot pedal and keep
it straight at all times. Do not bend at the hip, knee or ankle when mounting the
VersaClimber. Step on the high foot pedal with the good leg and while holding the hand rails,
move until both feet are at the same level. Lower the injured leg to the floor and the good
leg will raise to the initial position. Repeat the motion allowing the injured leg to be moved
just short of the stop, set to limit the range of motion of the injured leg. The good leg maintains a
full range of motion. If the injured leg can be flexed at the knee, set the limiter to allow
flexion to the extent that the injury will allow. This will gradually increase flexibility of the limb
and work the local muscle groups.

FOR ZERO RANGE OF MOTION IN ANKLE

For shin splints, achilles tendon pulls, ankle sprains, turf toe and calf pulls, stand on the foot
pedal with the heel of the injured foot contacting the pedal. Standing on the heel eliminates
both flexion and muscular loading of the ankle, achilles and calf. By pulling with the arm on
the injured leg side, further weight bearing loads can be removed from the injured leg. Stand
on the foot pedal with the ball of the foot to accentuate ankle and calf muscle usage. Stand
on the foot pedal with heel of the foot to accentuate the quad muscle usage.

Page 23

UNPACKING

INSTRUCTIONS

1. Remove the shipping container's top cover. Then remove the wooden cross support that
holds the mainframe down and the two bolts securing the machine to the end of the wood crate.
Using two people, carefully remove the vertical mainframe from the container and lay the
machine on the floor. Avoid lifting or setting the machine on any portion of the black plastic
housing or plastic oil accumulator (see page 26 for details).

A. (1) Mainframe post with control module

display attached

F. (1) Floor brace, 1/8" x 1

bar

1/2" rectangular

B. (1) Pair of foot pedals

C. (1) Pair of “Quick Release” handles

D. (1) Base plate

E. (1) Angle brace, 1

1/2" x 3" rectangular

tubing

The following items are included in the single machine shipping crate:

Padded Side Hand Rails

G. (2) Straight handrail supports, 1

1/2"

diameter

H. (2) S shaped padded side handrails

I. (1) AC adapter

J. (1) Hardware package

Flat Tie

Brace

Foot Pedals

Hand Rail Support Bars

Base Plate

Page 24

ASSEMBLY OF A VERSACLIMBER LX Series

NOTE:

Due to the durable, double welded, steel construction of the VersaClimber, two able bodied
persons are required for its set up. The set up procedure requires two 9/16” wrenches and two
crescent wrenches for pedals and side hand rails. Set up can be accomplished in about 15­20 minutes. When handling the machine, avoid lifting the machine by, or setting the
machine on any part of the black housing or oil reservoir (accumulator).

TOOLS REQUIRED FOR ASSEMBLY:

(I) Phillips screwdriver

(2) 9/16" wrenches

(2) Crescent wrenches

(1) 1/4" hex key

(2) 3/16" hex key

Two able body persons are
required for assembly.

HARDWARE PACKAGE CONTENTS

(1) 5/8" diameter x 41/4” hex head bolt and

locking nut

(2) 5/16" diameter x 21/2" round head

screws

(2) 3/8" - 16 x 1" hex head long bolts

Crescent Wrench

9/16" wrenches

Philips screw driver

1/4" hex key

3/16" hex key

(1) 3/8" - 16 diameter x 1

(7) 3/8" - self locking nuts

(1) 1/4" hex key

(1) 3/16" hex key

2) 5/16 – 18 x 1.5” Flat head bolt

(2) 3/8 – 16 x 1” Flat head bolt

(2) Washers

3/4" hex head screw

Page 25

Use two people to remove mainframe from
the shipping container.

Oil Reservoir

(Accumulator)

NOTE:

To protect the oil reservoir and the black
plastic computer housing, rest the top
end of the VersaClimber on a block of
wood. ALX models this is not required.

Bolt flat tie to brace using 3/8" self-locking
nut.

Place base plate into position and attach to
bottom of mainframe.

Assemble the two piece support brace.
Interlock flat tie to brace.

Tighten base plate to bottom of mainframe
post.

Page 26

Pre-Assemble the handrails. Bolt straight
tube onto the “S” shaped padded side rails.

Bolt second straight hand rail tube to the left
hand “S” shaped padded side rails. Use a
black 5/16” x 2

1/2” round head bolt and tighten

securely.

Attach pre-assembled hand rails to machine
post and base plate using two crescent
wrenches and a 3/16” allen wrench. Use the
5/8” x 4

1/4” long hex head bolt and lock nut to

fasten the rails to the block welded on the
back of the mainframe post. Tighten finger
tight.

Using two crescent wrenches, fasten the
upper part of rails to the block welded to the
back of the machine

Install the handles as follows. The machine
is supplied with one pair of quick release
straight handles. To insert, depress the pin
at the end of the handle. This “retracts” the
locking balls at the other end of the handle.
Insert the handle into any quick change
adaptor and release pin. This extends the
locking balls and secures the handle in
place.

Install standard straight handles. To insert
standard handle, depress pin with thumb
and insert.

While supporting the upper portion of the
rails, fasten lower part of rails to the base
plate using 5/16" x 1
screws. Now tighten the 5/8" x 4
bolt. Use the 5/16” x 11/2” long flathead socket
screws to fasten the hand rails to the base
plate. Tighten securely.

Running Handle. To insert running handle,
depress pin with thumb and insert.

1/2" long flat head

1/4" long

Page 27

NOTE:
IT IS IMPORTANT TO TIGHTEN THE FOOT
PEDALS SECURELY INTO POSITION.
INJURY MAY RESULT AND DAMAGE TO
THE MACHINE MAY OCCUR IF THEY ARE
NOT PROPERLY FASTENED.

Bolt foot pedals on machine, with " L" pointing
up, using two 3/8" x 1

1/4" long hex head bolts.

With one person standing on the base plate,
support mainframe the other person places
the previously assembled support brace into
position as shown above.

Next, attach the brace at the upper joint first
using the 2

1/4” bolt, (2) washers and self-

locking nut.
Attach the bottom joint of the support brace
using the self locking nut.

Raise or lower the brace in the slot until the
machine is stable “front to back”, flush on the
ground. Then fully tighten both nuts.

Tighten the 5/8” x 4

1/4” long bolts securely

using the two crescent wrenches.The hand
rails are now securely attached to each of the
machine posts and the machine base plate.

Using two people lift VersaClimber to upright
position.

Page 28

Tighten floor tie. Tighten locknut at bottom
of angle brace.

The machine is now free to stand on its own.

TO LEVEL THE MACHINE FRONT TO
BACK, LOOSEN THE 3/8” X 21/4“ LONG

BOLT. Position the base plate flat on the
floor. Move the brace in the slot until the
machine is stable front to back. Tighten the

1/4” long bolt.

2

Leveling Knob

TO LEVEL MACHINE LEFT TO RIGHT, first
level front to back. Then raise or lower the
two adjusting knobs in the base plate until the
machine is stable.

Notes:

Install the AC adaptor by plugging the
circular plugs into the appropriate receptacle
at the top of each VersaClimber (LX models
only), then plug it into any standard 120

V wall

outlet or extension cord.

Page 29

HI-TRI AND HIGH FIVE

ASSEMBLY

INSTRUCTIONS

The following VersaClimber assembly
instructions are to set up multi-station Hi-Tri
(3 stations) and High-Five (five stations)
configurations.

1. Follow the Unpacking and Assembly
Instructions for single machines. In place of
the base plate and two piece angled support
bracket, you will receive a circular top plate
or donut and 3 or 5 tubular floor ties and 3 or
5 base plates.

2. In place of the listed hardware, you will
receive four 1” long bolts, two 1/1/4 long
bolts, 8 self locking nuts and two flat head
screws per climber.

3. Due to the heavy construction of the
VersaClimber, two able bodied persons are
required for its set up. the set up procedure
requires two 9/16” wrenches, two crescent
wrenches, 1/4” allen wrench, 3/16” allen
wrench. Set up can be accomplished in
about 30 minutes. In handling the machine,
avoid lifting the machine by, or setting the
machine on any portion of the black plastic
housing, the hydraulic tubing or the hydraulic
reservoir. The hydraulic pump can be used
as a support or as a hand lift point.

4. Place the multi-machine base plates into
position on each of the climbers. Attach each
base plate to the mainframe of each climber
with two flat head screws through the bottom.
Tighten securely using an allen key and 9/16”
wrench.

5. Pre-assemble hand rails. Bolt one
straight hand rail tube to the right hand
angled “S” shaped tube. Use a 5/16” x 2
round head bolt and tighten securely.

1/2”

6. Bolt the second straight hand rail tube to
the left hand angled “S” shaped tube. Use a
5/16” x 2
securely.

7. Assemble rails to machine post and base
plate. Use the 5/8” x 4
and lock nut to fasten rails to the block
welded on the back of each machine.
Tighten, finger-tight.

8. Use the 5/8” x 1
screws to fasten the hand rails to the base
plates. Tighten securely.

9. Tighten the 5/8” x 4
using the two crescent wrenches.

10. The hand rails are now securely
attached to each of the machine posts and
the machine base plates.

11. Attach the first VersaClimber to the
circular top plate using four 1” bolts and four
self locking nuts. Angle brackets must set on
top of circular plate. Bolts go through from
bottom, nuts on top. Nuts must be snug but
not fully tightened.

12. Install second Versaclimber to top plate
in similar fashion. Do not fully tighten nuts.

13. Lift assembly of two Versaclimbers,
place third VersaClimber into position and
loosely tighten bolts through circular plate.

14. The High-Five multi-station will require
the attachment of two additional
VersaClimbers to the top plate.

15. Using the 1
nuts, connect the bases of the Versa
Climbers together with the tubular floor ties.
The ties overlap so that each tie is held by
two bolts at each VersaClimber with nuts on
the back side. Do not fully tighten until all ties
are in place.

1/2” round head bolt and tighten

1/4” long hex head bolt

1/2” long flat head socket

1/4” long bolts securely

1/4” bolts and self locking

Page 30

16. After all ties are in place, tighten bottom
tie nuts and bolts completely, (two per
VersaClimber).

17. After bottom tie bolts are fully tightened,
proceed to tighten all top plate nuts and
bolts.

18. Install the foot pedals by making sure the
“L” of the pedal is pointed up. Use two 3/8” ­16 x 1
each pedal. Bolt screws into the hole pattern
that is located 2
of each internal slide bar (carriage). Tighten
securely. The pedals are interchange able.

IT IS IMPORTANT TO TIGHTEN THE FOOT
PEDALS SECURELY INTO POSITION.
INJURY MAY RESULT AND DAMAGE TO
THE MACHINE MAY OCCUR IF THEY ARE
NOT PROPERLY FASTENED.

19. Install the handles as follows. The

machine is supplied with one pair of quick
change handles. To insert, depress the pin
at the end of the handle. This “retracts” the
locking balls at the other end of the handle.
Insert the handle into any quick change
adaptor and release the pin. This extends
the locking balls and secures the handle in
place.

1/4” hex head bolts provided to mount

1/4” and 41/4” from the bottom

NOTE:

MAINTENANCE

INSTRUCTIONS

MECHANICAL DESCRIPTION - The
VersaClimber consists of a mainframe made
of two rectangular tubes that are welded
together. The mainframe is supported by a
base plate and bracket that are bolted to it. A
shaft and sprocket is located at the top of the
mainframe. The shaft ends are supported
with ball bearings. One end of the shaft is
coupled to a digital shaft encoder that is used
to transmit climb rate and distance data to
the micro-computer.

Two rectangular bars that carry the handle
grips and foot pedals are located inside the
two rectangular tubes. These bars also carry
rollers and slide bearings. They are attached
to a roller chain that passes over the top and
bottom sprockets and connect the bars
together. While the VersaClimber is in use,
the bars travel vertically up and down inside
the rectangular tubing whenever the person
climbing exerts sufficient upward or
downward forces on the foot pedals or
handles. There are rubber shock mounts
located under the foot pedal shafts to absorb
any shock if the twenty-inch stroke is
exceeded. The digital encoder and micro­computer electronics are enclosed in a black
plastic housing mounted on the upper portion
of the machine.

20. Install the AC adaptor by plugging the
circular plugs into the appropriate receptacle
at the top of each Versaclimber (LX models
only), then plug it into any standard 120
outlet or extension cord.

V wall

Page 31

THE HYDRAULIC SYSTEM

The hydraulic system consists of a heavy
duty, reversible gear pump. A flow control
valve is connected between the input and the
output ports with copper tubing and heavy
duty high pressure tube fittings. A clear oil fill
reservoir is located on top of the pump, at the
very top of the unit.

NOTE: The oil in the pump reservoir always
darkens in color and most of the time, turns
black in color. This is normal.

The hydraulic resistance is developed in a
permanent closed loop system filled with

hydraulic oil that does not require changing.
The oil is maintained in the system with one
static seal and one rotating shaft seal. The
rotating shaft seal is rated for continuous
duty at operational pressures. If a large
amount of slack (more than 1/2" travel)
develops when reversing the stepping
motion, this indicates a possible loss of oil
from the system. Visually check the fittings
and the shaft seal for oil leaks. Tighten any
leaking fitting and then fill the reservoir with
oil up to 1/2" from the top.

PREVENTATIVE

MAINTENANCE SCHEDULE

Daily:

1) Wipe down the main post, base and side

rails with a rag and non-solvent, non-ammonia
cleaning solution.

Weekly:

1) Hand check quick-release handle bushings,

which the handles lock into, on both sides to
make sure they are tight.

ROLLER AND SLIDE

BEARINGS

There are rollers and slide bearings made
from high pressure application moly-disulfide
filled nylon on each oscillating bar. The roller
bearings are held on with 3/8” shafts and
press-on grip rings. The slide bearings are
held in place with two 3/8” pins. The slide
bearings have lubrication points. This
bearing material is expected to be
maintenance free for years. The bearings
are lightly lubricated at the factory and the
wear life and smooth operation of the
machine can be assured by lubricating every
two months or sooner if required. Lubricate
with 3-In-One High Performance Spray
Lubricant with PTFE.

NOTE: NEVER LUBE INTERNAL TRACKS
WITH ANY KIND OF GREASE.

You can find 3-In-One High Performance
Spray Lubricant with PTFE at Graingers
Industrial Supply www.grainger.com or
www.wd40.com (Item #10046 ). If not call our
service department 1-800-237-2271 ext.

226.

First wipe any excess oil, lint, dirt, etc. from
all i nter n a l acc e ssibl e surfa c es of the
rectangular tubing. Move the bars up and
down to allow access to clean the two foot
pedal slots and the two hand grip slots. Use
paint thinner to remove the oil and lint
residue. When clean, wipe or spray a synthetic
lubricant on all four internal surfaces of the
rectangular tubing.

2) Check oil level in top reservoir, it should
be at least 3/4 full when it leave the factory
and should never drop.

A) If oil level is low, fill using medium
wt. hydraulic oil. Oil level should
remain 3/4 full.

B) If you notice the oil has turned
dark or black, this is normal.
Oil never has to be changed.

(Excludes ALX model)

Monthly:

1) Check bottom chain tightness; with the

pedals even you should be able to push the
chain in about 1/4 inch. If the chain pushes
in more than this, then the chain is loose and
will need to be tightened. See below.

*To tighten the chain you will need a 9/16”
open end wrench. From behind the machine,
go to the bottom of the main post and there
will be an opening just above where the main
post connects to the straight base. In the
opening you will find a 9/16” hex head bolt.
Loosen the bottom bolt first, then loosen the
top bolt until the idler is movable. With a
screwdriver, push down gently on the flat
spacer under the bolt heads until the slack is
taken out of the chains. Then, while
maintaining chain tension, tighten the top
bolt first, then tighten the bottom bolt.

2) Spray internal tracks with 3-In-One
Synthetic Lubricant with PTFE to maintain a
smooth running fluid motion.

3) Check to make sure the pedals are spinning
freely, if not spray pedal shafts with 3-In­One Synthetic Lubricant with PTFE.

Page 32

Quarterly:

1) Wipe off the top & bottom chains and put

a very light coat of light grease on chain.

Using a toothbrush, or firm paint brush this is
the ONLY place you will use grease on the
VersaClimber.

NOTE: Never lube the internal tracks with
any kind of grease.

If this occurs, place the two foot pedals at
equal height and loosen the two bolts located
down in the slot at the back base of the
machine. Use a 9/16” open end wrench.

Loosen the bottom bolt first, then loosen the
top bolt or about 3/4 of a turn just enough for
the idler bracket is slightly movable.

CHAIN TENSION AND

LUBRICATION

The chain tension control is located at the
base of the machine.

It is set / adjusted at the factory to remove
slack in the lower chain. During the first few
weeks of operation, the chain and sprockets
will settle in and may produce a slight
amount of slack in the lower roller chain.

With a screwdriver, push down gently on the
flat spacer under the bolt heads until the
slack is taken out of the chains.

Then, while maintaining pressure on the
chain tension, tighten the top bolt first, then
tighten the bottom bolt.

Page 33

Every three months, lubricate the upper and
lower sprockets and upper and lower chain.
Use light grease.

With the aid of a flashlight and a 4 inch oil
spout can, place a few drops of oil between
the bottom sprocket hub and its mounting
bracket. Wipe off excess oil from the
sprocket and both chains. Lubricant may be
purchased directly from VersaClimber’s
Service Department by calling 1-800-237­2271 x226

OTHER MAINTENANCE

CLEANLINESS -- It is recommended that the
VersaClimber be placed on approximately a
five foot square rubber or plastic mat
because users are going to perspire profusely.
To prevent corrosion, it is recommended that
the machine mainframe and base plate be
wiped clean with soap and water at a "good
housekeeping frequency" to remove salts
and other body residues. Wipe machine
down no less than once a week. It is further
recommended that the machine be cleaned
and waxed once a month with any good
quality car wax.

HANDGRIPS -- The handgrips are a high
quality 1 1/4” diameter rubber bicycle grip.
When handle grips wear out replace them
with any good quality "flanged" grip from
your local bike shop or contact HRI for
spares.

FOOT PEDALS -- The foot pedals are made

of a strong durable extruded aluminum.
Every two months place a few drops of light
oil between the pedal and pedal shaft at both
ends of the foot pedal.

If a malfunction occurs, refer to trouble
shooting guide or contact the Heart Rate Inc.
Service Department for further instructions.

To remove the electronic control unit from a
single machine installation unit, simply
remove the four mounting screws on the
sides of the plastic console.

Then unplug the wires to the digital encoder
and from the power supply. Replacement is
the reverse of this procedure. If the unit is to
be shipped, package it carefully to avoid
physical damage.

The machine can be used while the
electronics are either turned off or out for
repair if the bare wire ends are insulated with
electrical tape.

TROUBLE SHOOTING

If a malfunction occurs, please refer to
the following symptom guide for instruction.

TO EXPEDITE SERVICE, CALL THE FACTORY
FIRST. RETURN ALL PARTS TO THE FACTORY
WITH A BRIEF NOTE STATING THE FACILITY
NAME, ADDRESS, PHONE NUMBER, CONTACT
NAME AND A DESCRIPTION OF THE SYMPTOM.
IF A DESCRIPTION OF THE PROBLEM IS NOT
INCLUDED WITH THE RETURNED PART,
REPAIRS MAY BE SIGNIFICANTLY DELAYED.
Please call Parts & Service 1.800.237.2271 x226

Page 34

SYMPTOM--ALL ZEROS ARE

REGISTERING ON MODULE.

If all zeros register on the display when the
machine is in motion, the computer is not
receiving input data from the upper rotating
shaft. The problem could be a faulty encoder
circuit board, broken or loose wire connectors
between the encoder circuit board and
computer or the encoder disk has become
detached from the pump shaft.

With the top black plastic cover removed,
slowly move the handles up and down. A
plastic encoder disc should be seen rotating
through a slot that houses infra red sensors.
Check to be sure that the disc and sensor are
clean and the encoder circuit board and the
module are in tact. If no mechanical malfunction
is visible, the encoder circuit board may be
faulty and should be replaced. If necessary,
contact Heart Rate, Inc. for further information.

SYMPTOM--LCD READOUT HAS

A BLACK SPLOTCH

If the display window is ruptured, the LCD
glass is also ruptured and a black shadow
area will appear in the LCD. The module will
need to be removed and returned to Heart
Rate, Inc. for LCD replacement and repair. To
remove the module, remove the four screws
that mount the module to the machine and
disconnect the wires from the module. The
machine can be used while the module is out
for repair.

SYMPTOM--MACHINE SQUEAK.

A lack of lubrication can cause a squeak in
the bottom sprocket shaft, or the foot pedal
shaft. To lubricate the bottom sprocket. If
rotating the foot pedal while standing on the
pedal causes a squeak, lubricate the
shaft/pedal interface. Remove the snap ring
from the end of the pedal shaft with snap ring
pliers being careful not to over extend the
ring. Remove the foot pedal and degrease
the shaft and pedal hole. If necessary, use
fine sandpaper to smooth the shaft surface.
Apply grease liberally and reassemble the
pedal. Be sure that the snap ring is fully

engaged in the groove.

SYMPTOM--MACHINE IS "STICKY"

IRREGULAR OR HARD TO MOVE.

The foot pedals and handgrips are attached
to metal bars that move up and down inside
C shaped metal channels. The bars have
plastic rollers and slides that guide the bars
through the channels. Over time, the
lubricant in the channels picks up dust and
lint and dries out producing a "sludge" tar like
coating that prevents smooth machine
operation. If the tar like coating is removed
the machine will function like brand new.

SYMPTOM--OIL ON BASE PLATE

Occasionally excess lubrication may be
applied at the factory and run down the
inside of the post onto the base plate. Do not
be concerned, all parts are functioning
normally. Wipe up the excess oil with a rag.

SYMPTOM-- OIL LEAK FROM

HYDRAULIC ADJUSTMENT KNOB

An oil leak from the hydraulic knob indicates
a malfunction in the needle valve. The needle
valve must be replaced. Do not remove the
defective valve until you receive the new
one. Installation instructions will be sent from
the factory with your replacement valve.

SYMPTOM-- OIL LEAK FROM

RESERVOIR ON HYDRAULIC MOTOR

If oil leaks from the top seal between the
black plastic cap and the plastic bowl, tighten
cap by hand. If oil leaks from the threads at
the base of the accumulator, tighten by
turning clockwise with an open-end wrench.
If reservoir is physically damaged and a
replacement is required, do not remove the
reservoir until you receive a new one. The
replacement will include installation
instructions.

Page 35

VERSACLIMBER SPECIFICATIONS

PHYSICAL SIZE

Height, Model CL-108LX 7 feet, 10 inches
Height, Model CL-109LX 8 feet, 10 inches
Required Floor Space 48 inches x 48 inches
Weight 130lbs. - 150 lbs - Assembled

PHYSICAL CHARACTERISTICS

Structural Steel
Sliding and Rolling Bearings Filled Nylon
Speed Control/Force Control Hydraulic
Date Processing 8 Bit Microcomputer
Data Display 22 Digit LCD
110 VAC Powered 12 Volt AC Adapter
Quick Change Hand Grips 2
Stationary Hand Rails 2
Hand Grip Adjustment 3.75 Inch Increments
Foot Pedals 2

FUNCTIONAL FEATURES

Pedal/Step/Climb Stroke Length 0 To 20 Inches
Overall Climb Rate Ability Of Person Climbing
Hydraulic Climb Rate Control 20-240 Feet/Min.
Hydraulic Force Control 0 To 500 Lbs.
Program Workout Levels 1 To 15
Heart Rate Control 120 To 190
Climb Angle 75 Degrees
Vertical Lift Factor 96.6 Percent

VERSACLIMBER ACCOMMODATIONS

Level of Physical Fitness Sedentary To Elite Athlete
Climber's Height 4 Feet 6 Inches And Taller
Climber's Weight 50 To 350 Pounds
Age and Sex Any

MICROCOMPUTER FUNCTIONS

Exercise Time 0 To 99.9 Minutes
Exercise Rate 0 To 350 Feet/Min.
Total Exercise Distance 0 To 9999 Feet
Total Exercise Steps 0 To 9999 Feet
Step Height/Stroke Length 0 To 20 Inches

Page 36

SPARE PARTS LIST

In the event that a replacement part is ordered from the factory, Please refer to the
following spare parts list for the correct part description and part number. This information
will expedite your shipment when calling our Service Department.

LX Module (108/109) LX........................................................................................158-01-000

LX Module (108A/109A) LX...................................................................................161-01-000

LXP Module (1081109) LXP...................................................................................166-02-000

LXP Module (108A/109A) LXP...............................................................................166-03-000

Encoder Circuit Board Assembly.........................................................................013-01-000G

Encoder Disc......................................................................................................... 013-01-003

Electrodes...............................................................................................................041-00-000

LCD/VersaClimber .........................................................................................................54502

Accumulator....................................................................................................................30038

Valve Stem......................................................................................................................30027

Foot Pedal Assembly..............................................................................................101-04-000

Foot Pedal Straps...................................................................................................008-03-000

Foot Pedal Connector, (Plastic Triangle)................................................................008-00-007

Quick Change Handle (1).......................................................................................101-06-000

Quick Change Running Handle (1) .......................................................................101-03-000

Handle Grip Only.............................................................................................................30009

8’ Bar - Left.............................................................................................................055-00-000

8’ Bar - Right...........................................................................................................054-00-000

Slides......................................................................................................................003-00-009

Rollers....................................................................................................................003-00-005

CL-108 Pump Assembly.........................................................................................039-00-000

AC Adaptor......................................................................................................................60019

AC Adaptor Assembly - Hi-Tri.................................................................................114-00-000

AC Adaptor Assembly - Hi-Five..............................................................................115-00-000

Brackets - HI-Tri Assembly (108)........................................................................... 048-00-000

Brackets - High Five Assembly (108).....................................................................050-00-000

Base Plate..............................................................................................................101-00-001

Brace......................................................................................................................101-00-003

Tie...........................................................................................................................101-00-002

Rail Assembly (no base plate)................................................................................047-02-000

Station Base Plate..................................................................................................047-00-008

8’ Top Cover............................................................................................................029-00-000

Bottom Chain Assembly..........................................................................................037-00-000

Top Chain Assembly...............................................................................................043-00-000

Pump Sprocket...............................................................................................................30010

Sprocket Assembly (CL-108A/CL-109A)................................................................042-00-000

Pump Sprocket Bushing (Post 1990).............................................................................30065

Seat........................................................................................................................019-02-000

Ears - Left...............................................................................................................147-00-005

Ears - Right............................................................................................................147-00-004

Leg Isolator.............................................................................................................145-01-000

Page 37

Stopper................................................................................................................... 101-00-008

Flange (108ALX/109ALX) (2 each)................................................................................30033

Bearing (108ALX/109ALX) (1 each)...............................................................................30044

Super Lube..................................................................................................................... 30090

Top Chain Master Link....................................................................................................30003

Bottom Chain Master Link..............................................................................................30007

Front Strip.......................................................................................................................60039

Bottom Sproket Assembly.......................................................................................002-00-000

A/C Jack Assembly.................................................................................................045-00-000

Small Brass Elbow........................................................................................B-500-2-2 30026

Large Brass Elbow........................................................................................B-500-2-4 30014

For Parts & Service Please call: 1.800.237.2271 x226

VERSACLIMBER

THREE YEAR LIMITED WARRANTY

1. Heart Rate, Inc. (H.R.I.) warrants to the original purchaser that Institutional VersaClimbers are

free from defects in material and workmanship under normal use and maintenance under a three
year limited warranty subject to the terms and conditions Hereafter set forth. Except for the above
warranty, it is expressly agreed that NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE or of a particular use nor any warranty of any kind whatsoever express,
implied or statutory is made by H.R.I.

2. This warranty does not cover any damage caused by misuse, tampering, negligence, accidents,
abnormal conditions, lack of adequate maintenance or unauthorized service or alterations to the product.

3. Liability of H.R.I. is limited to either repair or replacement of the defective part or the replacement
of the machine at the option of H.R.I. on an exchange basis, with the customer bearing all costs of
shipping and handling to and from the factory.

4. Length of Warranty, Parts

ITEM

FRAME, HAND RAILS, BASE PLATE 3 YEARS
HYDRAULIC MOTOR 3 YEARS
FOOT PEDALS 2 YEARS
HANDLES 2 YEARS
CHAINS AND SPROCKETS 2 YEARS
DISPLAY ELECTRONICS 2 YEARS
ROLLERS AND SLIDES 2 YEARS
ELECTRONICS 1 YEAR
HAND GRIPS 1 YEAR
FOOT PEDAL STRAPS 1 YEAR
SEAT 1 YEAR

5. Length of Warranty, labor
During the first year, all labor is covered by the warranty. All labor repairs will be performed at the
factory on warranty and non-warranty parts.

PARTS REPLACEMENT

Page 38

6. This warranty does not cover paint deterioration, discoloration, chipping or rust.

7. After all of the foregoing conditions have been complied with, if H.R.I. shall thereupon attempt

repairs and /or replacements which shall for any reason fail, H.R.I.’s shall be allowed to continue to
attempt to remedy any defects for so long a period of time as, In H.R.I. sole judgement, such
attempt is justified.

8. The foregoing shall be buyer’s sole and exclusive remedy, whether based on or otherwise, and
H.R.I. shall not be liable for any injuries to persons or property. In no event shall H.R.I. be liable for
incidental or consequential damages to commercial losses, nor for any other loss or damages
except as above set forth.

9. This warranty is expressly in lieu of all other warranties, express or implied, and of all other
obligations or liability on the part of H.R.I. No person, firm or corporation is authorized to assume
any other liability on behalf of H.R.I.

VERSACLIMBER WARRANTY VALIDATION FORM

To validate your Warranty Registration, please fill out the following form and return it to
Heart Rate, Inc.

VersaClimber Model Number:___________________________________________

Machine Serial Number:_______________________________________________

Name:_________________________________Title:________________________

Facility Name:_______________________________________________________

Address:____________________________________________________________

City:_______________________________State:_____________Zip:___________

Phone Number: (_____)____________________ (_____)_____________________

Email:__________________________Fax: (____)___________________________

Purchase Date:_______________________From HRI [ ] Dealer [ ] Other [ ]

Dealer Address:______________________________________________________

City_______________________State_________________Zip________________

I first saw/heard about the VersaClimber:__________________________________

___________________________________________________________________

I have seen the VersaClimber advertisements in the following magazines:________

___________________________________________________________________

Page 39

VersaClimber, 3190-E, Airport Loop, Costa Mesa, CA 92626 • Toll free: 1.800. 237.2271
Tel: [phone] Fax: [phone] Email: [e-mail] Visit us online at www.versaclimber.com

A trusted name in tness for nearly 30 years. Proudly made in USA since 1981.

To learn more about other great VersaClimber accessories and options to enhance
your workout, please visit us on line at www.versaclimber.com or call our toll free
number at 1.800.237.2271 for more details.

MADE IN THE U.S.A.