Vernier LS-BTA User Manual

Light Sensor

(Order Code LS -BTA)

The Light Sensor can be used for
measurements of light intensity in a variety
of situations.

 Perform inverse square light intensity experiments using a point source of light.
 Conduct polarized filter studies.
 Demonstrate the flicker of fluorescent lamps and other lamps.
 Carry out solar energy studies.
 Perform re flecti vity stu dies.
 Study light intensity in various parts of a house or school.
 Use it as part of a study of plant growth to measure light intensity.

Note: Vernier products are designed for educational use. Our products are not
designed nor are they recommended for any industrial, medical, or commercial
process such as life support, patient diagnosis, control of a manufacturing
process, or industrial testing of any kind.

Compatible Software and Interfaces

See www.v ern ier.c om/man ua ls/l s-b ta for a list of interfaces and software compatible
with the Light Sensor.

Getting Started

1. Connect the sensor to the interface (LabQuest Mini, LabQuest 2, etc.).

2. Start the appropriate data-collection software (Logger Pro, Logger Lite,
LabQuest App) if not already running, and choose New from File menu.

The software will identify the sensor and load a default data-collection setup. You
are now ready to collect data.

If you are collecting data using a Chromebook™, mobile device such as iPad

®

or
Android™ tablet, or a Vernier wireless sensor or interface, please see the following
link for up-to-date connection information:

www.vern ier.co m/sta rt/ ls- bt a

Using the Product

Connect the sensor following the steps in the Getting Started section of this user
manual.

The switch on the box is used to select the range. If the reading from the sensor
reaches the maximum for the selected ranges, you need to switch to a less sensitive
range. If the reading is very small or 0, you need to select a more sensitive range.

 The 0–600 lux range is the most sensitive range. It is useful for low levels of

illumination.

 The 0–6000 lux range is a good general purpose range for indoor light levels.
 The 0–150,000 lux range is used mainly for measurements in sunlight.

Videos

View videos related to this product at www.vern ier.c om/l s-b ta

Calibration

You should not have to perform a new calibration when using the Light Sensor in
the classroom. We have set the sensor to match our stored calibration before
shipping it. If you have a calibrated light meter and would like to calibrate the
Light Sensor to match it, you can find instructions at

www.vern ier.co m/til/3615

Specifications

13-bit resolution 0–600 lux: 0.1 lux

0–6000 lux: 1 lux

0–150000 lux: 25 lux

12-bit resolution 0–600 lux: 0.2 lux

0–6000 lux: 2 lux

0–150000 lux: 50 lux

10-bit resolution 0–600 lux: 0.3 lux

0–6000 lux: 8 lux

0–150000 lux: 200 lux

Default calibration values 0–600 lux

slope: 154 lux/V

intercept: 0 lux

0–6000 lux

slope: 1692 lux/V

intercept: 0 lux

0–150000 lux

slope: 38424 lux/V

intercept: 0 lux

How the Sensor Works

The sensor uses a silicon photodiode. It produces a voltage that is proportional to
light intensity. The spectral response approximates the response of the human eye,
as shown in this diagram.

2

Troubleshooting

The Light Sensor is sensitive enough to pick up the 60 or 120 Hz flicker of
overhead fluorescent lamps, which may interfere with light experiments. If you
think such interference may be occurring, try the following:

 First, eliminate all artificial light sources (except battery-powered flashlights)

and try your experiment again.

 Next, test the Light Sensor positioned as you plan to use it. Set the sampling at

1000 points/second for 0.1 second. If the flicker is the problem, you will see a
drastic variation in the light intensity with a period of 60 or 120 Hz
(50 or 100 Hz outside of North America).

 If the overhead flicker is an issue, set the sampling rate to a number that is not

a factor of 60. For example, using 30, 20, or 10 samples/s is worse than using
17, 23, 27 samples/s.

For further troubleshooting tips and FAQs, see

www.vern ier.co m/til/1419

Repair Information

If you have watched the related product video(s), followed the troubleshooting
steps, and are still having trouble with your Light Sensor, contact Vernier
Technical Support at [e-mail] or call 888-837-6437. Support
specialists will work with you to determine if the unit needs to be sent in for
repair. At that time, a Return Merchandise Authorization (RMA) number will be
issued and instructions will be communicated on how to return the unit for repair.

Warranty

Vernier warrants this product to be free from defects in materials and workmanship
for a period of five years from the date of shipment to the customer. This warranty
does not cover damage to the product caused by abuse or improper use. This
warranty covers educational institutions only.

3

Vernier Software & Technology

139 79 SW M illikan Way • Be aver ton , OR 97005-2886

Toll Free (888) 837- 6437 • (503) 277- 2299 • FAX [phone]

[e-mail]• www.vernier.com

Rev. 2/8/16

Logger Pro, Logger Lite, Vernier LabQuest 2, LabQuest Mini, and other marks shown are our trademarks or
registered trademarks in the United States.

All other marks not owned by us that appear herein are the property of their respective owners,who may or may
not be affiliated with, connected to, or sponsored by us.

4