Verner pH Sensor User Manual

pH Sensor

(Order Code P H-BTA)

The pH Sensor can be used for any lab or demonstration
that can be done with a traditional pH meter, including
acid-base titrations, monitoring pH in an aquarium, and investigating the water
quality of streams and lakes.

Note: Vernier products are designed for educational use. Our products are not
designed nor are they recommended for any industrial, medical, or commercial
process such as life support, patient diagnosis, control of a manufacturing
process, or industrial testing of any kind.

What's Included

 pH Sensor
 Electrode Storage bottle, containing pH 4/KCl solution

Compatible Software and Interfaces

See www.v erni er.c om/man ua ls/p h-b ta for a list of interfaces and software compatible
with the pH Sensor.

Getting Started

1. Connect the sensor to the interface (LabQuest Mini, LabQuest 2, etc.).

2. Start the appropriate data-collection software (Logger Pro, Logger Lite,
LabQuest App) if not already running, and choose New from File menu.

The software will identify the sensor and load a default data-collection setup. You
are now ready to collect data.

If you are collecting data using a Chromebook™, mobile device such as iPad

®

or
Android™ tablet, or a Vernier wireless sensor or interface, please see the following
link for up-to-date connection information:

www.vern ie r.co m/st art/ ph -b ta

Using the Product

1. Remove the storage bottle from the electrode by unscrewing the lid and

removing the bottle and lid.

2. Thoroughly rinse the lower section of the probe, especially around the

bulb-shaped tip, using distilled or deionized water.

3. Connect the sensor following the steps in the Getting Started section of this

user manual.

4. When you are finished making measurements, rinse the electrode with distilled

water.

5. Slide the cap onto the electrode body, and then screw the cap onto the storage

bottle so the tip of the electrode is immersed in the storage solution.

Important: Do not fully submerge the sensor. The handle is not waterproof.

Do not leave the electrode in acids or bases with concentrations greater than

1.0 M for periods longer than 5 minutes. See

www.vern ie r.co m/ph -s ens ors fo r other

types of pH electrodes.

Videos

View videos related to this product at www.vern ier.c om/p h-b ta

Calibration

For many experiments, calibrating the pH Sensor is not required. A calibration
equation is stored on each pH Sensor before they are shipped, which is used as a
default by Vernier software.

For the most accurate measurements with this sensor, we recommend calibration. It
is a simple process that takes only a few minutes.

 For instructions for pH Sensor calibration using Logger Pro computer software,

see

www.vern ie r.co m/til/2341

 For instructions for pH Sensor calibration using LabQuest App, see

www.vern ie r.co m/til/3394

 For instructions for pH Sensor calibration using Graphical Analysis with a

Chromebook, see

www.vern ie r.co m/til/3631

 For instructions for pH Sensor calibration using Graphical Analysis with an

iOS or Android device, see

www.vern ie r.co m/til/3630

In order to calibrate a pH Sensor, or to confirm that a saved pH calibration is
accurate, you should have a supply of pH buffer solutions that cover the range of
the pH values you will be measuring. For more information about pH buffer
solutions, including recipes for preparation, see

www.vern ie r.co m/til/3625

Specifications

Type Sealed, gel-filled, polycarbonate body, Ag/AgCl

Response time 90% of final reading in 1 second in a buffer

Temperature range 5 to 80°C (readings not compensated)

Range pH 0–14

Accuracy ± 0.2 pH units

Isopotential pH pH 7 (point at which temperature has no effect)

Default calibration values slope: –3.838

intercept: 13.720

Shaft diameter 12 mm OD

Care and Maintenance

Short-term storage (up to 24 hours): Place the electrode in pH 4 or pH 7 buffer
solution. It should never be stored in distilled water.

Long-term storage (more than 24 hours): Store the electrode in a pH 4
buffer/KCl storage solution in the storage bottle. The pH electrode is shipped in

2

this solution. Vernier sells 500 mL bottles of pH Storage Solution (order code
PH-SS), or you can prepare additional storage solution by adding 10 g of solid
potassium chloride (KCl) to 100 mL of pH 4 buffer solution. Vernier sells a
pH Buffer Capsule kit (PH-BUFCAP) that includes a buffer solution preservative.
Storing the electrode in this solution contributes to electrode longevity and retains
electrode response time when the unit is placed back into service.

If the electrode is inadvertently stored dry for a short period of time, immerse the
tip in the pH 4 buffer/KCl storage solution for a minimum of 8 hours prior to use.
If the readings are still not accurate after calibration or if the response is slow, try
shocking the sensor as described in the Troubleshooting section.

How the Sensor Works

The pH amplifier inside the handle is a circuit that allows the standard
combination pH electrode to be monitored by a lab interface. The cable from the
pH amplifier ends in a BTA plug.

The pH Sensor produces a voltage of approximately 1.75 volts in a pH 7 buffer.
The voltage increases by about 0.25 volts for every pH number decrease. The
voltage decreases by about 0.25 volts/pH number as the pH increases.

The Vernier gel-filled pH Sensor is designed to make measurements in the pH
range of 0 to 14. The gel-filled reference half cell is sealed; it cannot be refilled.

The pH Sensor is designed to be used in aqueous solutions. The polycarbonate
body of the sensor can be damaged by many organic solvents. In addition, do not
use the sensor in solutions containing: perchlorates, silver ions, sulfide ions,
biological samples with high concentrations of proteins, or Tris buffered solutions.
Do not use the sensor with hydrofluoric acid or in acid or base solutions with a
concentration greater than 1.0 molar.

Troubleshooting

When testing a pH Sensor, it is best to measure a buffer solution because it is
easier to determine if the sensor is reading correctly. Do not test your sensor by
measuring distilled water. Distilled water can have a pH reading in the range of

5.5–7.0, due to varying amounts of dissolved carbon dioxide. Furthermore, due to
a lack of ions, the pH values reported with the sensor in distilled water will be
errat ic.

If your pH Sensor is reading differently from the pH of a buffer solution (e.g., reads

6.7 in a buffer 7), you may simply need to calibrate the sensor. See the Calibration
section for more information.

Examine the glass bulb. If it is broken, pH readings will be incorrect.

If your readings are off by several pH values, the pH readings do not change when
moved from one buffer solution to a buffer solution of different pH, the sensor was
stored dry for an extended period of time, or the sensor’s response seems slow, the
problem may be more serious. A method called “shocking” can be used to revive
pH electrodes. To shock your pH Sensor, perform the following:

3

1. Soak the pH Electrode for 4–8 hours in an HCl solution of 0.1 M–0.5 M.

2. Rinse off the electrode and soak the tip in freshly prepared long term storage
solution (recipe above) for 30–60 minutes.

3. Rinse the electrode and test it with buffer solutions of known pH.

Occasionally, mold will grow in the pH 4 buffer/storage solution. Mold will not
harm the electrode and can easily be removed using a mild detergent solution.
Mold growth in the storage solution can be inhibited by adding a buffer
preservative.

For additional troubleshooting and FAQs, see

www.vern ie r.co m/til/1361

Repair Information

If you have watched the related product video(s), followed the troubleshooting
steps, and are still having trouble with your pH Sensor, contact Vernier Technical
Support at [e-mail] or call 888-837-6437. Support specialists will
work with you to determine if the unit needs to be sent in for repair. At that time,
a Return Merchandise Authorization (RMA) number will be issued and
instructions will be communicated on how to return the unit for repair.

Accessories/Replacements

Item Order Code

Electrode Storage Solution, 500 mL PH-SS
pH Buffer Capsules (3×10) kit PH-BUFCAP
Storage Solution Bottles, pkg of 5 BTL

Warranty

Vernier warrants this product to be free from defects in materials and workmanship
for a period of five years from the date of shipment to the customer. This warranty
does not cover damage to the product caused by abuse or improper use. This
warranty covers educational institutions only. Additionally, the warranty does not
cover accidental breakage of the glass bulb of the pH Sensor.

Vernier Softwar e & Technology

139 79 SW M illikan Way • Be aver ton, O R 97005- 2886

Toll Free [phone] • [phone] • FAX [phone]

[e-mail]• www.vernier.com

Rev. 2/8/16

Logger Pro, Logger Lite, Vernier LabQuest 2, LabQuest Mini, and other marks shown are our trademarks or
registered trademarks in the United States.

All other marks not owned by us that appear herein are the property of their respective owners,who may or may
not be affiliated with, connected to, or sponsored by us.

4