Vermont Castings LSTF36, LPF36, LRF36, LLF36, 36STFL Installation Instructions Manual

Thermostatic Blower
Installation Instructions
Model: BLOTDL

Before You Start

This instruction sheet is ONLY for models listed below. Carefully inspect the contents for shipping damage. If any parts
are missing or damaged, immediately inform the dealer from whom you purchased the part.

Models: LSTF36, LPF36, LRF36, LLF36, 36STFL, 36PFL, 36RFL, 36LFL, (ST, CL, CR, PF)LDV

Kit Contents:

(1) Blower Assembly (4) Screws #14 x 3/4 (2) Screws #8 x 1/2 (1) Power Cord
(1) Speed Control (1) Speed Control Mounting Bracket (2) Wire Ties
(1) Gasket (2) High Temperature Wire (4) Rubber Grommets
(1) Thermostatic Sensor (Large screw-in style) (1) Thermostatic Sensor (Small snap-in style)
Tools Required:
Phillips screwdriver, Small jeweler’s style screwdriver

Before installing the blower, turn off the replace
and allow to cool. Only a qualied service person
should service and repair the replace. A qualied
service person should connect and disconnect the
replace to gas supply. Follow all local codes.

WARNING

Electrical Grounding Instructions:

This appliance is equipped with a three-prong
(grounding) plug for your protection against shock
hazard and should be plugged directly into a prop­erly grounded three prong receptacle.

WARNING

Electrical connections should only be performed
by a qualied licensed electrician. Main power
supply must be turned off before connecting fans
to the main electrical power supply or performing
service.

CAUTION

IMPORTANT: Always check local building codes. This

installation must comply with local regulations as well
as the National Electric Code.

Installation Instructions

Wiring

1. Before installing the blower, wire the receptacle into an electrical circuit. This should be done
before framing the replace. Wire with minimum 60° C wire in accordance with prevailing
codes.

2. Remove the external junction box cover by removing the screw
from the left side of the outside rebox wall. Junction box was
installed at the factory.

3. The junction box cover has a factory installed “romex” style strain
relief connector. After connecting the wires, route the wire leads
through this connector. Refer to the wiring diagram in Figure 1.

Junction Box

Figure 1
Junction Box Wiring Diagram

120V AC
60Hz

Factory Supplied

Not Supplied

79D0009 1/13 Rev. 3

Installation Instructions - (LF,FL)

NOTE: The blower can be installed through the end access panel
at time of replace installation before framing.

1. Disconnect gas line and remove burner and logs.

2. Remove brick wall(s) and hearth oor. Figure 3

3. Remove blower access/mounting plate. Figure 3

4. Mount the blower to the mounting plate by using the four (4) rub­ber grommets between the blower and plate. Attach with four (4)
#14 x 3/4 screws. Figure 5. NOTE: The blower may be mounted
on either side of unit according to which side the air is to be
discharged.

Install Thermal Sensor

NOTE: There are two (2) thermal sensors packed with this kit. Be

sure to install the correct sensor. Figure 6

1. Remove the thermal sensor plate located inside at top of re­place on the air channel. Figure 4

2. Route the two (2) thermal sensor wires down through the air
channel to the bottom blower compartment of the unit. Align
the thermal sensor and attach to the sensor mounting plate
with screws provided. After the sensor is mounted reinstall the
mounting plate with the screws previously removed. Figure 4

Attach Speed Control

1. Slide the speed control knob through slot from under the blower
compartment. Align mounting holes in side panel to mounting
bracket. Use two (2) #8 x 1/2 screws to attach. Figure 5

2. Connect wiring according to the wiring diagram. Figure 2

WARNING: It is important to wire tie the loose wires and arrange

the wiring harness neatly so the wires cannot come in contact
with blower fan blades.

3. Plug power cord into junction box.

4. Reinstall blower access panel/mounting plate with blowers in­stalled.

5. Reinstall brick, burner and logs in reverse order of removal.

6. To operate blower, turn replace ON. Turn the knob on the
speed control clockwise. The blower should be operating
at the highest speed within 10 min­utes. Continue to turn the knob until
it reaches the desired speed. If the
low speed is set too low, it can be
adjusted. Figure 6

KT1353

Figure 2 ­Brick Removal

2

Speed
Control

Figure 3 ­Speed Control Installation

Blower

Blower Access /
Mounting Plate

KT1354

79D0009