Vermont Castings Intrepid 1640 Owners Installation And Operating Manual
The Intrepid
Woodburning Stove
Model 1640
Homeowner’s
Installation and
Operating Manual
f i r e - p a r t s . c o m
For use in the
United States and Canada
SAFETY NOTICE: IF THIS APPLIANCE IS NOT PROPERLY INSTALLED, OPERATED AND MAIN
TAINED, A HOUSE FIRE MAY RESULT.
TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. FAILURE TO
FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN
DEATH. CONTACT LOCAL BUILDING OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION
INSPECTION REQUIREMENTS IN YOUR AREA.
CFM Specialty Home Products
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777
www.majesticproducts.com • www.vermontcastings.com
-
Do Not Discard This Manual: Retain for Future Use
30000830 4/05 Rev. 5
Intrepid 1640 Woodburning Stove
C US
Introduction
Thank you for choosing a Vermont Castings Intrepid to meet your heating needs. We’re confident you will find the
Intrepid to be an effective wood-burning heater incorporating modern, non-catalytic combustion technology with the
classic aesthetic appeal of its Vermont Castings lineage.
The Intrepid achieves high-efficiency through precisely calibrated delivery of primary and secondary air into a refrac
tory-insulated firebox. Properly operated and maintained according to the guidelines in this manual, your Intrepid will
provide safe, dependable, and economical heating for years to come.
The Intrepid Model 1640 series has been tested and is listed by the Canadian Standards Associa
tion (CSA). The test standards are ANSI/UL-1482 for the United States and ULC S627 and CAN/CSA
B366.2 for Canada.
The Intrepid Model 1640 is listed for burning wood fuel only. Do not burn other fuels.
The Intrepid Model 1640 is approved for installation in manufactured (mobile) homes in the United
States only using the optional Mobile Home Kit #1881 in accordance with the instructions in that kit
and any local codes.
The Intrepid Model 1640 complies with the standards set forth by the Federal Environmental Protection Agency, 40
CFR Part 60.532(b)(2), as stated on the permanent label attached to each stove.
We recommend that you hire a professional, solid-fuel stove technician to install your Intrepid, or to advise you on the
installation should you attempt to install it yourself. Consult the authority having local jurisdiction (such as a municipal
building department, fire department, fire prevention bureau, etc.) before installation to determine the need for a building permit. Also, consult your insurance agent to be sure your installation complies with specific requirements that may
vary locally.
In addition to directions on installation and operation, this manual includes directions on maintenance and assembly.
Please read this entire manual before you install or operate your new room heater.
f i r e - p a r t s . c o m
Save These Instructions For Future Reference.
-
-
Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of
combustion of such fuels, contain chemicals known to
the State of California to cause cancer, birth defects
and other reproductive harm.
California Health & Safety Code Sec. 25249.6
Table of Contents
Specifications .....................................3
Installation Requirements ...................4
Clearances .........................................14
Assembly ...........................................16
Operation ............................................18
Maintenance ....................................... 22
Appendix - Draft Management ...........25
Parts List ...........................................28
Installation Accessories
#1878 Outside Air Kit
#1881 Mobile Home Kit
#0307 Bottom Heat Shield
#0868 Short Legs - Classic Black
#1515 Short Legs - Red
#1512 Short Legs - Sand
#1520 Short Legs - Moonlight Blue
#1510 Short Legs - Green
#0136 Sparkscreen
#0098 Warming Shelf - Classic Black
#1355 Warming Shelf - Red
#1362 Warming Shelf - Sand
#1363 Warming Shelf - Moonlight Blue
#1365 Warming Shelf - Forest Green
2
30000830
Specifications
22”
560mm
24”
610mm
20
”
520mm
21
”
545mm
25”
630mm
21”
540mm
18
”
470mm
4”
112 mm
19”
482mm
18”
473 mm
Rear Exit
Flue Collar
Top Exit
Flue Collar
Height
Top Exit
Flue Collar
C
L
14”
356mm
C
L
Intrepid, Model 1640
Maximum Heat Output ............8,200 - 19,500 Btu’s/hr.
Maximum Heat Output ..........................22,00 Btu’s/hr.
Area Heated .....................Up to 1000 sq. ft.(92 sq. m)
Fuel Size / Type ................................16” (410 mm) logs
EPA Emissions Rating (g/h, non-catalytic) ..............3.33
Loading Front
Chimney Connector .................... 6” (150 mm) diameter
Chimney Flue Size .....................6” (150 mm) minimum
Flue Exit Position ..................... Reversible, Top or Rear
Primary Air ... Manually set, thermostatically maintained
Secondary Air .........................................Self-regulating
Ash Handling System ................... Removable Ash Pan
Glass Panels ................High-temp Ceramic, IR Coated
Weight 255 lbs. (116kg.)
Height to top of flue collar:
With regular legs ...........25¹⁄₄” (630mm) top exit
....................................... 24” (610mm) rear exit
With optionalshort legs . 21¹⁄₄” (540mm) top exit
....................................... 20” (510mm) rear exit
Intrepid 1640 Woodburning Stove
1
This value can vary depending on how the stove is operated,
3
1
2
the type and moisture content of the fuel used, as well as
the design, construction and climatic location of your home.
Figures shown are based on maximum fuel consumption
obtained under laboratory conditions and on average efficiencies.
2
These values are based on operation in building codeconforming homes under typical winter climate conditions
in New England. If your home is of nonstandard construction (e.g., unusually well insulated, not insulated, built under
ground, etc.) or if you live in a more severe or more temperate
climate, these figures may not apply. Since so many variables
affect performance, consult your Vermont Castings authorized
dealer to determine realistic expectations for your home.
3
Under specific conditions used during EPA emissions test-
ing.
f i r e - p a r t s . c o m
Fig. 1 Intrepid 1640 dimensions.
30000830
0830
3
Intrepid 1640 Woodburning Stove
2' Min.
2' Min.
3'
Min.
0 To 10'
3'
Min.
0 To 10'
Installation
SAFETY NOTICE: IF YOUR STOVE IS NOT PROPERLY INSTALLED, OPERATED AND MAINTAINED, A
HOUSE FIRE MAY RESULT. FOR SAFETY, FOLLOW
ALL INSTALLATION, OPERATION AND MAINTENANCE DIRECTIONS. CONTACT LOCAL BUILDING
OFFICIALS ABOUT RESTRICTIONS AND IN�.
Before you begin an installation, review your plans to
be certain that:
• Your stove and chimney connector will be far
enough from combustible material to meet all clearance requirements.
• The floor protector is large enough and is construct-
ed properly to meet all requirements.
• You have all necessary permits from local authori-
ties.
Your local building official is the final authority for approving your installation as safe and determining that it
meets local and state codes.
The metal label permanently attached to the back of
the stove indicates that the Intrepid has been tested
to current UL and ULC standards by CSA. Clearance and installation information is also printed on the
f i r e - p a r t s . c o m
label. Local authorities generally will accept the label
as evidence that, when the stove is installed according
to the information on the label and in this manual, the
installation meets codes and can be approved. Codes,
however, vary in different areas. Before starting the
installation, review your plans with the local building
authority. Your local dealer can provide any additional
information needed.
For any unresolved questions about installation, refer
to the National Fire Protection Association’s publication
ANSI/NFPA 211–1988 Standard for Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances. In
Canada, the equivalent publication is CSA CAN-B365,
Installation Code for Solid Fuel Burning Appliances and
Equipment. These standards are the bases for many
national codes. They are nationally recognized and are
accepted by most local authorities. Your local dealer
or your local building official may have a copy of these
regulations.
IMPORTANT: FAILURE TO FOLLOW THESE IN
STALLATION INSTRUCTIONS MAY RESULT IN A
DANGEROUS SITUATION, INCLUDING A CHIMNEY
OR HOUSE FIRE. FOLLOW ALL INSTRUCTIONS
EXACTLY AND DO NOT ALLOW MAKESHIFT COMPROMISES TO ENDANGER PROPERTY AND PER-
SONAL SAFETY.
4
-
Your stove must be connected either to a sound
masonry chimney that meets local codes, to a relined
masonry chimney that meets local codes, or to an
approved prefabricated metal chimney. Whichever of
those types you use, the chimney and chimney connector must be in good condition and kept clean.
If you use an existing masonry chimney, it must be
inspected to ensure safe condition before the stove is
installed. Your local professional chimney sweep, building inspector, or fire department official will be able to
make the inspection or direct you to someone who can.
The chimney should extend at least 3’ (914mm) above
the highest point where it passes through a roof, and at
least 2’ (610mm) higher than any portion of a building
within 10’ (3m).
To assure proper draft and good performance, any
chimney used with this stove should extend at least 16’
(5 m) above the flue collar of the stove.
Reference Point
Fig. 2 The 2’-3’-10’ Chimney Rule.
An existing masonry chimney must be inspected to confirm that it has a lining. Do not use an unlined chimney.
The chimney also should be examined for cracks,
loose mortar, other signs of deterioration, and blockage.
Repair any defects before the chimney is used with
your stove.
A prefabricated doublewall insulated chimney
A tile-lined
masonry
chimney
Fig. 3 Standard Chimney Types
Chimneys
Masonry Chimneys
AC617
ST241
30000830
Intrepid 1640 Woodburning Stove
Masonry Chimneys, cont’d.
• Unused openings in an existing masonry chimney
must be sealed with masonry to the thickness of
the chimney wall, and the chimney liner should be
repaired. Openings sealed with pie plates or wallpaper are a hazard and should be sealed with mortar
or refractory cement. In the event of a chimney
fire, flames and smoke may be forced out of these
unused thimbles.
• The chimney should be thoroughly cleaned before
use.
• A newly-built masonry chimney must conform to the
standards of local building code, or, in the absence
of a local code, to a recognized national code. Masonry chimneys must be lined, either with code-approved masonry or precast refractory tiles, stainless
steel pipe, or a code-approved, “poured-in-place”
liner. The chimney clean-out door must seal tightly to
ensure a good draft.
Prefabricated Chimneys
A prefabricated metal chimney must be one that is tested and listed for use with solid-fuel burning appliances
to the High-Temperature (H.T.) Chimney Standard
UL-103-1985 (2100°F.) for the United States, and High
Temperature (650°C) Standard ULC S-629 for Canada.
f i r e - p a r t s . c o m
Chimney Size
This stove is approved for venting into a masonry chimney with a nominal flue size of 8” x 8” (203 x 203mm),
and into a round flue size of 8” (203mm) or 6” (152mm).
It may be vented into larger chimneys as well. However, chimneys with liners larger than 8” x 12” (203 x
305mm) may experience rapid cooling of smoke and
reduction in draft, especially if they are located outside
the home. Such large chimneys may need to be insulated or have the flue relined for proper stove performance.
Do not connect this unit to a chimney flue serving another appliance.
Note: Do not vent this stove into a factory-built
(zero-clearance) fireplace. This stove has not
been tested and listed for that type of installation. Factory-built fireplaces and their chimneys
are specifically designed as a unit for use as
fireplaces. It may void the listing or be hazard
ous to adapt them for any other use.
Do not connect the STOVE to any air distribu
tion duct or system.
-
-
Ask your dealer about components available for connecting the stove to a steel chimney liner.
Chimney Connector Guidelines
A chimney connector is the double-wall or single-wall
pipe that connects the stove to the chimney. The chimney itself is a masonry or prefabricated structure that
encloses the flue. Chimney connectors are used only
to make the connection from the stove to the chimney.
They are for interior use only.
Double-wall connectors must be tested and listed for
use with solid-fuel burning appliances. Single-wall connectors should be made of 24 gauge or heavier steel,
and should be 6” (152mm) in diameter. Do not use
galvanized chimney connector; it cannot withstand the
high temperatures that can be reached by smoke and
exhaust gases, and may release toxic fumes under high
heat.
If possible, do not pass the chimney connector through
a combustible wall or
ceiling. If passage
through a combustible
wall is unavoidable,
refer to the recommendations in the section
following on Wall Passthroughs. Do not pass
the connector through
an attic, a closet or
any similar concealed
space. The whole
chimney connector
should be exposed and
accessible for inspection and cleaning.
Install the single wall chimney connector not less than
18” (457mm) from the ceiling. Keep it as short and
direct as possible, with no more than two 90° turns. If
possible, use 45° elbows. Slope horizontal runs of connectors upward 1/4” per foot (20 mm per meter) going
from the stove toward the chimney. The recommended
maximum length of a horizontal run is 3 feet (1 meter),
and the total length of chimney connector should be no
longer than 8’ (2.4meters).
In cathedral ceiling installations, extend the prefabricated chimney downward to within 8’ (2.4m) of the stove.
SAFETY NOTE: ALWAYS WEAR GLOVES AND PRO
TECTIVE EYEWEAR WHEN DRILLING, CUTTING OR
JOINING CHIMNEY CONNECTOR SECTIONS .
Toward
stove
Fig. 4. Chimney connector.
Flue gas
direction
-
30000830
5
Intrepid 1640 Woodburning Stove
Double-wall Chimney Connectors
The Intrepid is approved for installation in the U.S. and
Canada with double-wall chimney connectors that have
been tested and listed for use with solid-fuel burning
appliances by a recognized testing laboratory.
Follow the instructions for assembling and installing
double-wall connectors provided by the manufacturer of
the double-wall chimney. To ease assembly and help
assure safety, use chimney components manufactured
by a single source.
NOTE: For installations using double-wall connectors, minimum clearances must conform to those
listed in the clearance chart on Page 14.
Thimble Sleeve
Chimney
Connector
Fig. 6 The thimble, made of either ceramic or metal, must be
cemented securely in place.
Flue
Keep sleeve
end flush with
flue tile
ST243
Single-wall Chimney Connectors
• Beginning at the flue collar of the stove, assemble
the chimney connector. Insert the first crimped end
into the stove’s flue collar, and keep each crimped
end pointing toward the stove. Using the holes in
the flue collar as guides, drill 1/8” (3mm) holes in the
bottom of the first section of chimney connector and
secure it to the flue collar with three #10 x 1/2” sheet
metal screws.
• Secure each joint between sections of chimney
connector, including telescoping joints, with at least
f i r e - p a r t s . c o m
three sheet metal screws. The predrilled holes in
the top of each section of chimney connector serve
as guides when you drill 1/8” (3mm) holes in the bottom of the next section.
• Secure the chimney connector to the chimney. In-
structions for various installations follow.
• Be sure the installed stove and chimney connector
are correct distances from nearby combustible material.
Note: Special slip pipes and thimble sleeves that form
telescoping joints between sections of chimney connector are available to simplify assembly. Slip pipes
eliminate the need to cut individual connector sections.
Consult your local dealer about these special connector
sections.
Securing the Single-wall Connector to a
Prefabricated Chimney
Follow the installation instructions of the chimney
manufacturer exactly.
Special adaptors are available from your local dealer to
make the connection between the prefabricated chimney and the chimney connector. The top of such adaptors attach directly to the chimney or to the chimney’s
ceiling support package. The bottom of the adaptor is
secured to the chimney connector.
The adapter forms a union between the chimney and
chimney connector that ensures any soot or creosote
falling from the inner walls of the chimney will stay
inside the chimney connector.
Securing the Single-wall Connector to a
Masonry Chimney
The Intrepid may be connected to either a freestanding
masonry chimney or to a fireplace masonry chimney.
Freestanding Installations
If the chimney connector must pass through a combustible wall to reach the chimney, follow the recommendations for Wall Pass-Through construction on Pages 7-8.
The opening through the chimney wall to the flue - the
“breech” – must be lined with a ceramic or metal
thimble which is securely cemented in place.
A metal pipe section called the “thimble sleeve,” slightly
smaller in diameter than standard connector and the
thimbles, will allow the removal of the chimney connector system for inspection and cleaning. Thimble
sleeves are available from your local dealer.
To install a thimble sleeve, slide it into the breech until
it is flush with the inner flue wall. Be sure that it does
not extend into the flue passage where it could interfere
with the draft.
The thimble sleeve should protrude 1-2” (25-50mm) into
the room. Use furnace cement and thin gasketing to
seal the sleeve in place in the thimble. Secure the chimney connector to the outer end of the sleeve with sheet
metal screws.
6
30000830
Intrepid 1640 Woodburning Stove
Connection Above the Fireplace
In this installation, the chimney connector enters the
fireplace flue though a thimble located above the fireplace. The liner of the fireplace chimney should extend
at least to the point at which the chimney connector
enters the chimney. Follow all the guidelines for installing a chimney connector into a freestanding masonry
chimney, and pay special attention to these additional
points:
• Check the stove and chimney connector clearances
to combustible mantel and trim materials. If necessary, use a combination of mantel, trim, and connector heat shields to provide the required clearances.
Refer to Page 12.
• Double-check connector clearance to the ceiling.
• The fireplace damper must be closed and sealed to
prevent room air from being drawn up the flue which
could reduce performance. However, it must be
possible to reopen the damper to inspect or clean
the chimney.
• Floor protection requirements also apply to fireplace
installations. Refer to Page 8.
Wall Pass-throughs
Whenever possible, design the installation so that the
connector does not pass through a combustible wall.
If you must include a wall pass-through in your installation, check with your building inspector before you
begin. Also check with the chimney connector manufacturer for any specific requirements.
Consult with your dealer regarding special connection
components available for use as wall pass-throughs.
Use only parts that have been tested and listed for
use as a wall pass-through. Refer to Figures 9 - 12 for
further details.
U.S. Requirements:
The National Fire Protection Association (NFPA) has
established guidelines for use in the United States for
passing chimney connectors through combustible walls.
Many building code inspectors follow these guidelines.
Figure 9 shows one NFPA-approved method. All combustible material in the wall is cut away to provide 12”
(305mm) clearance to the connector. Brick and mortar
are used to enclose the clearance area.
Fire clay liner
Min. 2” (51mm) Chimney clearance to brick and combustibles
f i r e - p a r t s . c o m
With Chimney Connector Heat Shields 10”
(250 mm)
10”
(250 mm)
Mantel
ST244a
Fig. 7 If the clearance between the chimney connector and
either the ceiling or the mantel is inadequate, a protective
heat shield is required.
A
A
Fig. 9 Masonry Wall Pass-through with single wall
chimney connector.
Alternate Methods Approved by the NFPA:
• Using a section of double-wall chimney with a 9”
(229mm) clearance to combustibles. (Fig. 10)
• Placing a chimney connector pipe inside a steel
double-wall ventilated thimble, which is then separated from combustibles by 6” (152mm) of fiberglass
insulating material. (Fig. 11)
• Placing a chimney connector pipe inside a section
of 9” (229mm) diameter, solid-insulated, factory-built
chimney, with two inches of air space between the
chimney section and combustibles. (Fig. 12)
Masonry
Chimney
constructed
to NFPA 211
Chimney Flue
A = Minimum 12” (305 mm) brick construction between liner and combustible
framing materials
Min. 12”
(305 mm)
Fire clay
liner
Chimney connector
30000830
7
Intrepid 1640 Woodburning Stove
Solid insulated,
listed factorybuilt chimney
length set flush
with flue
Masonry
Chimney
constructed to
NFPA 211
Non-soluble refractory cement
ST273
Min. 9”
230mm
Sheet Steel
Supports
Fig. 10 Wall Pass-through using factory-built insulated
chimney section.
Chimney clearance to sheet steel
supports and combustibles
Steel Thimble
with two 1”
(25mm) Ventilated
Channels
Min. 2”
(51mm)
Chimney Flue
2” (51mm) Min.
Min. 9”
(230mm)
Air Space
24 ga.Sheet
Steel Supports
Min. 6”
(152mm)
Chimney
Connector
your local building inspector can provide details of other
approved methods of passing a chimney connector
through a combustible wall.
In Canada, this type of installation must conform to
CAN/CSA-B365, Installation Code for Solid Fuel Burning Appliances and Equipment.
Min. 18”
(460mm)
ST276
Fig. 13 CSA approved Wall Pass-through.
Chimney clearance to sheet steel
supports and combustibles
Chimney Flue
24 ga. Sheet
Steel Support
(one side only)
2” (51mm)
Min.
Min. 18”
(460mm)
Chimney
Connector
24 ga.Sheet
Steel Support
Masonry Chimney
constructed to CAN/CSAB365
Chimney Connector
Masonry Chimney construct
ed to NFPA 211
f i r e - p a r t s . c o m
ST274
-
Chimney Flue
Glass Fiber
Insulation
24 ga.Sheet
Steel Supports
Fig. 11 Wall Pass-through using single wall chimney
connector with a ventilated steel thimble.
ST275
Chimney clearance to sheet steel
supports and combustibles
2” (51mm) Min.
air space
Prefab Chimney
Section
24 ga. Sheet
Steel Supports
Chimney Flue
2” (51mm)
Min.
2” (51mm) Min.
Chimney Connector
Prefab
Chimney
Section
24 ga. Sheet
Masonry Chimney constructed to NFPA 211
Steel Supports
Fig. 12 Wall Pass-through with ventilated steel thimble.
A tremendous amount of heat radiates from the bottom
plate of an Intrepid II, and the floor beneath requires
two kinds of special protection.
Heat protection is provided by a Vermont Castings Bottom Heat Shield, part #0307.
Spark and ember protection is provided by a floor protector, which may be any noncombustible material.
For a new hearth, we recommend a noncombustible
floor protector such as 1/4” non-asbestos mineral board
or its equivalent, or 24 gauge sheet metal. If carpeting
is present, it must be removed before installation of the
floor protector. The floor protector may be covered with
a noncombustible decorative material if desired. When
using brick, tile, or stone, individual pieces must be
mortared so sparks cannot fall through.
When the optional 3” (75mm) short legs are used, the
bottom heat shield must be used.
Most installations will require that the bottom heat
Floor Protection
shield be attached. Only when the stove is placed
Canadian Requirements:
In Canada, the Canadian Standards Association has
established specific guidelines regarding wall passthough design. Figure 13 shows one approved method
in which all combustible material in the wall is cut away
to provide the required 18” (457mm) clearance around
the connector. The resulting space must remain empty.
A flush-mounted sheet metal cover may be used on one
side only. If covers must be used on both sides, each
cover must be mounted on noncombustible spacers at
least 1” (25mm) clear of the wall. Your local dealer or
on a completely noncombustible surface, such as
unpainted concrete over earth, may it be used without the bottom heat shield.
Even with the bottom heat shield installed, you must
also use a floor protector.
In the United States, the floor protector required under
the stove must extend at least 16” from the front of the
stove - not from the ashlip - ( ‘E’ in Fig. 14), and at least
6” from the sides and rear (‘D’, Fig. 14).
To meet the requirement in the United States, a floor
protector must be at least 34” wide and 40” deep.
8
30000830
In Canada, the floor protector required under the stove
D
D
DD
D
E
E
B
C
A
A
must extend 18” (457mm) to the front (‘E’, Fig. 14), and
8” (203mm) from the sides and rear. (‘D’ ,Fig. 14)
To meet Canadian requirements, a floor protector must
be at least 43” (1092mm) wide and 48” (1219mm)
deep.
Floor protection also must extend under the chimney
connector and 2 inches to either side. (‘C’, Fig. 14)
For 6” (152mm) connector used with the Intrepid II, the
protector must be a minimum of 10” (254mm) wide,
centered under the connector.
Floor Protection Requirements
Top Exit Rear Exit
Intrepid 1640 Woodburning Stove
Wooden Framing
Fig. 15 Supporting timbers under fireplace hearths are
considered to be combustible.
from the front in the United States and 18” (457 mm)
from the front in Canada.
The optional 3” (75 mm) legs may be used only on
hearths that meet the width and depth requirements.
Hearth rugs do not satisfy the requirements for floor
protection as they are only fire-retardant, not fire proof.
ST247b
Mobile Home Installation
The Intrepid is approved for use in manufactured
(mobile) homes when installed with the optional Ver
f i r e - p a r t s . c o m
U.S. Canada
A 34” 38” (965 mm)
B 40” 42” (1067 mm)
C 10” 10” (254 mm)
D 6” 8” (203 mm)
E 16” 18” (457 mm)
Fig. 14 These dimensions are minimum requirements only.
Use greater dimensions whenever possible.
Fireplace Hearth Protection
Do not assume that your fireplace hearth is completely
noncombustible. Many fireplace hearths do not satisfy
the “completely noncombustible” requirement because
the brick or concrete in front of the fireplace opening
is supported by heavy wood framing. Because heat
is readily conducted by brick or concrete, it can easily
pass through to the wood. As a result, such fireplace
hearths can be a fire hazard and are considered a combustible floor.
For all fireplace installations, follow the floor protection
guidelines described above.
Keep in mind that many raised hearths will extend
less than the required clearance from the front of the
heater when it is installed. In such cases, sufficient
floor protection as described above must be added in
front of the hearth to satisfy the minimum floor protector
requirement from the front of the stove: 16” (416 mm)
30000830
ST567
mont Castings Mobile Home Kit #1881 in accordance
with the instructions provided with that kit and any local
codes. This approval applies only in the United States.
In addition to the standard installation requirements
described in this manual, the following guidelines apply
to mobile home installations:
1. The stove must be permanently secured to the floor
using the leg clamps and fasteners provided in the
kit.
2. The stove must have a permanent connection to the
outside to supply combustion air.
3. The stove must be grounded to the steel chassis of
the mobile home.
4. A listed chimney system, including roof thimble,
spark arrestor, chimney supports, roof flashing and
any other components suitable for use in mobile
homes must be used. The chimney system must
comply with the standard for Chimneys Factory-Built
Residential Type and Building Heating Appliances
UL 103.
5. The chimney must be attached directly to the stove
and must extend at least 3’ (914 mm) above the part
of the roof through which it passes. The top of the
chimney must extend at least 2’ (610 mm) above the
highest point of any part of the mobile home structure within 10’ (3 m) of the chimney.
-
9
Intrepid 1640 Woodburning Stove
6. If the chimney exits the mobile home through a wall
at a point 7’ (2.1 m) or less above the ground level
on which the mobile home is located, a guard or
other noncombustible enclosure must be fitted at the
point of exit and extend up to a height of 7’ (2.1m).
Any openings in this guard must be smaller than 3/4”
(19mm).
7. Check all local building codes, specifically those
related to mobile homes. Other requirements may
be applicable to chimney system removal for transportation of the mobile home.
WARNING:
room or hallway.
CAUTION: The structural integrity of the mobile
home roof, floor, walls and ceiling must be maintained.
Do not install the Intrepid in a sleeping
Clearance to Surrounding
Combustible Materials
When the stove is operating, both the stoveplate and
the chimney connector radiate heat in all directions. A
safe installation requires that adequate clearance be
maintained between the stove and nearby combustible
materials to ensure that those materials do not overheat.
Clearance is the distance between either your stove
f i r e - p a r t s . c o m
or chimney connector, and nearby walls, floors, the
ceiling, and any other fixed combustible surface. Keep
furnishings and other combustible materials away
from the stove as well. In general, a distance of 48”
(1219mm) must be maintained between the stove and
moveable combustible items such as drying clothes,
furniture, newspapers, firewood, etc. Keep this area
empty of any combustible material.
Safe Ways To Reduce Clearances
The Intrepid clearance requirements, listed and
diagramed on Pages 14-15, have been established
through testing to UL and ULC standards to meet most
installation configurations. These involve four basic
variables:
Reducing a stove clearance may require installation of
a listed heat shield on the chimney connector as well.
Clearances may be reduced only by means approved
by the regulatory authority, or in accordance with the
clearances listed in this manual.
When determining clearance, always measure from
the top plate of the stove, or, from the chimney connector itself, to the adjacent combustible surface. Do not
measure from the heat shields of the stove or connector
to the combustible surface.
Wall Shields
Wall shields should be constructed of 24 gauge or
heavier sheet metal, or another noncombustible material such as 1/2” (13mm) insulation board or common
brick “laid on flat,” with the 3¹⁄₂" (89mm) side down.
Shields must be spaced out from the combustible surface 1" (25mm) on noncombustible spacers. The spacers should not be directly behind the stove or chimney
connector. (Fig. 16)
Air must be able to flow between the wall and the
shield. At least 50% of the bottom 1" (25mm) of the
shield should be open and the shield must be open at
the top.
Air flow
Screen
Stud wall
framing
Wall shield
Noncombustible spacers
and fasteners
Metal Spacer
Drywall
Air flow
• When the stove has no listed heat shield in-
stalled.
• When the stove does have a listed heat shield
mounted on it.
• When the wall has no listed heat shield installed.
• When the wall does have a listed heat shield
mounted on it.
In general, the greatest clearance is required when the
stove will be positioned with no heat shield near a wall
with no heat shield. The least clearance is required
when both the stove and the wall have heat shields.
Fig. 16 Approved Wall shield construction
The following examples of wall shield construction illustrate common designs used to safely achieve reduced
clearances to combustible wall materials.
Parallel installation, vertical chimney connector,
two wall shields. Fig. 17: Reduced clearances for
both rear and side walls. Wall shields may meet at
corner if desired. Shielding for connector is centered
behind connector.
Shield
ST248
10
30000830
Loading...