INSTALLER/CONSUMER
SAFETY INFORMA TION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING APPLIANCE.
Electric
WARNING!
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, AN ELECTRICAL
SHOCK OR FIRE MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS
OF LIFE.
FOR YOUR SAFETY
Service must be performed by
a qualified service agency.
DO NOT STORE OR USE
GASOLINE OR OTHER
FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
APPLIANCE.
Fireplace
Model:
DEF/DEFD26
DEF26_photo
Homeowner’s Installation &
Operating Manual
C US
410 Admiral Blvd. • Mississauga • Ontario, Canada L5T 2N6 • Ph: 905-670-7777
INSTALLER: DO NOT DISCARD THIS MANUAL - LEAVE FOR HOMEOWNER
Vermont Castings, Majestic Products
www.majesticproducts.com • www.vermontcastings.com
10005581 07/03 Rev.0
Vermont Castings, Majestic Products DEF/DEFD26
Table of Contents
Thank you, and Congratulations on your purchase of a Vermont Castings, Majestic Products Fireplace.
Please read the Installation & Operating Instructions before using this appliance.
IMPORTANT: Read all instructions and warnings carefully prior to commencing installation. Failure to follow
these instructions may result in a possible electric shock, fire hazard and/or injury and will void
the warranty.
Installation Instructions
General ....................................................................................................................... 3
Locating your Electric Fireplace .................................................................................. 3
Clearance to Combustibles ......................................................................................... 3
Hearth ......................................................................................................................... 3
Electrical Specifications .............................................................................................. 3
Optional Cabinet Dimensions...................................................................................... 4
Optional Cabinet Installation ....................................................................................... 4
Fireplace Dimensions.................................................................................................. 5
Screen Information...................................................................................................... 6
Electrical Connection .................................................................................................. 6
Service Instructions
Removal of Logs ......................................................................................................... 6
Cleaning Trim.............................................................................................................. 6
Replacing the Light Bulbs ........................................................................................... 7
Maintenance of Motors................................................................................................ 7
Trim Kit Installation...................................................................................................... 7
Electrical Wiring Diagram with Integral Remote Control ............................................. 8
Electrical Wiring Diagram without Integral Remote Control ........................................ 8
Operating Instructions
1. Main ON/OFF Switch .............................................................................................. 9
2. Heater Control......................................................................................................... 9
3. Flame Speed Control .............................................................................................. 9
4. Re-learn .................................................................................................................. 9
5. ON/OFF................................................................................................................... 9
Replacement Parts List
Replacement Parts List ............................................................................................. 10
Warranty .................................................................................................................................. 11
2
10005581
Installation Instructions
General
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns,
do not let bare skin touch hot surfaces. If provided,
use handles when moving this appliance. Keep
combustible materials, such as furniture, pillows,
bedding, papers, clothes and curtains at least 3'
(1 m) from the front of this appliance.
CAUTION: Extreme caution is necessary
when any heater is used by or near
children or invalids and whenever the
heater is left operating and unattended.
3. If possible, always unplug this appliance when not
in use.
4. Do not operate any heater with a damaged cord or
plug or after the appliance malfunctions, or if it has
been dropped or damaged in any manner.
5. Any repairs to this fireplace should be carried out
by a qualified service person.
6. Under no circumstances should this fireplace be
modified. Parts having to be removed for servicing
must be replaced prior to operating this fireplace
again.
7. Do not use outdoors.
8. This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never
locate this appliance where it may fall into a bathtub or other water container.
9. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners or the like. Arrange cord
away from traffic areas and where it will not be
tripped over.
10. To disconnect this appliance, turn controls to the
OFF
position, then remove plug from outlet.
11. Connect to properly grounded outlets only.
12. This appliance, when installed must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the current CSA
C22.1 Canadian Electrical Code or for U.S.A.
installations follow local codes and the National
Electrical Code, ANSI/NFPA NO. 70.
13. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause
an electric shock or fire, or damage the appliance.
14. To prevent a possible fire, do not block air intakes
or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become
blocked.
15. This appliance has hot and arcing or sparking parts
inside. Do not use it in areas where gasoline, paint
or flammable liquids are used or stored. This
10005581
fireplace should not be used as a drying rack for
clothing, nor should Christmas stockings or
decorations be hung in the area of it.
16. Use this appliance only as described in this
manual. Any other use not recommended by the
manufacturer may cause fire, electric shock or
injury to persons.
17. Avoid the use of an extension cord because the
extension cord may overheat and cause a risk of
fire. However, if you have to use an extension
cord, the cord shall be No. 14 AWG minimum size
and rated not less than 1875 Watts. The extension
cord must be a 3-wire cord with grounding-type
plug and cord connection.
shall not be more than 20' (6.1 m) in length.
18. SAVE THESE INSTRUCTIONS.
The extension cord
Locating Your
Electric Fireplace
Your new fireplace may be installed with an approved
Vissan cabinet.
When choosing a location for your new fireplace,
ensure that the general instructions are followed. For
best effect, install the fireplace out of direct sunlight.
Clearance to Combustibles
Sides .................................. 0" (0 mm)
Floor...................................0" (0 mm)
Top.....................................0" (0 mm)
Hearth
A hearth is not mandatory; however, it is recommended
for aesthetic purposes. Installation of a noncombustible
hearth that will not obstruct the louvre opening is
recommended.
Cold climate installation recommendation:
When installing this unit against a noninsulated exterior wall or chase, it is
mandatory the outer walls be insulated to
conform to applicable insulation codes.
Electrical Specifications
Voltage: 120VAC, 60Hz
Total Amps: 12.2 Amps
Total Watts: 1460 Watts
Heater Rating: 1300 Watts
3
Vermont Castings, Majestic Products DEF/DEFD26
Optional Cabinet Dimensions
Face
Pillar
C
A
B
G
J
H
Front Base
E
D
F
Back edge
K
I
Front and Side
Views of Cabinet
5581 cab dims
5581 base dims
Reference All Models
A 26 5/8" (676 mm)
B 26 1/2" (673 mm)
C 43 7/8" (1114 mm)
D 36 1/2" (927 mm)
E 13" (330 mm)
F 10 3/8" (264 mm)
G 38 1/2" (978 mm)
H 44 1/4" (1124 mm)
I 3" (76 mm)
J 45 1/4" (1149 mm)
K 15 1/2" (394 mm)
Optional Cabinet Installation
1. Refer to the installation instructions on Page 3 in
this owner's manual for electrical hookup and
SAFETY RULES.
2. Place the cabinet base into position, back edges of
the cabinet base flush against the wall.
3. Place the fireplace onto the base, centered side-toside, back edge of fireplace approximately 1"
(25 mm) out from the wall.
4. Place the cabinet assembly over the fireplace. The
opening in cabinet fits over fireplace, back edges of
the cabinet flush against the wall. Place the front of
the fireplace up flush against the front face of the
cabinet between the two (2) pillars.
4
10005581
Vermont Castings, Majestic Products DEF/DEFD26
Fireplace Dimensions
ROH
ROW
ROD
A
B
C
D
Framing & Finishing
E
A
G
F
5581 HEF26 specs
Reference All Models
A 26 1/8" (664 mm)
B 25 7/8" (657 mm)
C 17 1/2" (445 mm)
D 24 1/4" (615 mm)
E 10" (254 mm)
F 20 1/8" (511 mm)
G 21 1/4" (540 mm)
Rough Opening Depth (ROD) 10 1/2" (267 mm)
Rough Opening Width (ROW) 26 5/8" (676 mm)
Rough Opening Height (ROH) 26 3/8" (670 mm)
10005581
5
Vermont Castings, Majestic Products DEF/DEFD26
Screen Information
1. Under no circumstances is this product to be
operated if the screen door(s) are missing.
2. Do not strike or slam the screen doors.
3. This product uses screen doors. Replacement
screen doors are available from the manufacturer.
Replacement must be carried out by a qualified
service person.
Electrical Connection
A 15 AMP, 120 Volt, 60 Hz circuit with a properly
grounded outlet is required. Preferably, the fireplace
will be on a dedicated circuit as other appliances on
the same circuit may cause the circuit breaker to trip or
the fuse to blow when the heater is in operation.
The unit comes standard with a 6’ (1828 mm) long
3-wire cord, exiting from the side of the fireplace.
Plan the installation to avoid the use of an extension
cord. If an extension cord must be used, it must be a
minimum 14 AWG, 3-wire cord with grounding-type
plug connector, and rated not less than 1875 Watts.
The cord shall not be more than 20' (6.1 m) in length.
WARNING: Electrical outlet wiring must
comply with local building codes and
other applicable regulations to reduce
the risk of fire, electrical shock and
injury to persons.
WARNING: Do not use this fireplace if
any part of it has been under water.
Immediately contact a qualified service
technician to inspect the fireplace and
replace any part of the electrical system.
WARNING: This fireplace comes with a
manual circuit breaker reset near the
power cord supply. In case the fireplace
is not operating check the circuit breaker
and reset the button at the breaker. If the
fireplace remains inoperable,
immediately contact a qualified service
technician to perform an inspection.
Service Instructions
Removal of Logs
1. Turn
2. Let fireplace cool if it has been operating.
3. Gently open both screen doors.
4. Remove the two (2) screws securing the ember bed
Fig. 1 Electric logset
OFF
power to the unit by unplugging the
power cord.
and logset in position. One (1) screw is located on
either side of the ember bed near the center.
LG237_DEF26_logs
WARNING: Disconnect power before
attempting any maintenance or cleaning
to reduce the risk of fire, electrical shock
or personal injury.
Cleaning Trim
Clean the metal trim using a soft cloth, slightly
dampened with lemon oil, then buff with a clean soft
cloth. DO NOT use brass polish or household
cleaners, as these products will damage the metal
trim. Lemon oil may be obtained at supermarkets and
hardware stores.
6
10005581
Vermont Castings, Majestic Products DEF/DEFD26
Replacing the Light Bulbs
This fireplace uses two (2) clear 120 Volt, 60 Watt,
E-12 socket base light bulbs (small base, chandelier
candle type). The 60 Watt bulbs are located under the
logset/ember bed. For convenience, if one (1) of the
bulbs burns out, it will be prudent to replace both of the
light bulbs.
1. Turn
2. Let fireplace cool if it has been operating.
3. Remove the four (4) screws securing the bottom
4. Examine the bulbs to determine which bulb needs to
5. While holding the socket, unscrew defective bulb(s).
6. Install the new light bulb(s) by screwing it in while
7. Reinstall the bottom louvre. Follow the above
OFF
power to the unit by unplugging the power
cord.
louvre. Pull the louvre up and lift it out.
be replaced.
holding the socket.
procedure in reverse order.
WARNING: Do not exceed 60 Watts per
bulb. Use of higher-rated bulbs may result
in a fire, causing property damage or
personal injury.
Maintenance of Motors
Trim Kit Installation
1. Peel all plastic from the Trim Kit Assembly.
2. Press the Trim Kit Assembly onto the front of the
fireplace. To facilitate the installation process, these
pieces are magnetized. Align the top of the Trim Kit
Assembly with the top of the fireplace.
DEF26_3D
Fig. 2 Trim kit installation
The motors used on the fan and the flame generator
assembly are prelubricated for extended bearing life
and require no further lubrication. However, periodic
cleaning/vacuuming of the fan/heater unit is
recommended.
WARNING: Make sure the power is
turned
OFF
before proceeding.
10005581
7
Vermont Castings, Majestic Products DEF/DEFD26
Electrical Wiring Diagram with Integral Remote Control
Any electrical repairs or rewiring of this unit should be
carried out by a licensed electrician in accordance with
national and local codes.
11
BLACKBLACK
9 BLACK9 BLACK
REDRED
10 RED10 RED
FLAMEFLAME
MOTORMOTOR
++
SPEED SPEED
CONTROLCONTROL
--
1414
14 WHITE14 WHITE
7 BLACK7 BLACK
13 WHITE13 WHITE
6 BLACK6 BLACK
8 RED8 RED
T'T'
SS
TT
AA
TT
1010
1010
1111
5 BLACK5 BLACK
WHITEWHITE
BLACKBLACK
12 WHITE12 WHITE
1010
33
FANFAN
MOTORMOTOR
SWITCHSWITCH
ON/OFFON/OFF
HEATER HEATER
ELEMENTELEMENT
22
11 WHITE11 WHITE
4 BLACK4 BLACK
3 BLACK3 BLACK
2 BLACK2 BLACK
55
1010
66
44
BREAKERBREAKER
CIRCUITCIRCUIT
1 BLACK1 BLACK
15 WHITE15 WHITE
IN NIN N
OUT NOUT N
IN LIN L
OUT LOUT L
If repairing or replacing any electrical
component or wiring, the original wire
routing, color coding and securing
locations must be followed.
1. Motor Variable Speed 12VDC
2. Switch ON/OFF
3. Thermostat
4. Fan/Heater
5. Light Socket w /Wiring Assemblyy
6. Light Bulb 60 W
7. Breaker Circuit Manual Reset
8. Power Cord 16/3 HPN with Terminal
9. Bushing Straight-Thru Strain Relief
10. Cable Tie Nylon 6" - 11/8 Black
11. Bushing Snap 0.875"-0.625"
12. CFM Majestic Factory Wire Required
77
13. Receiver
14. Potentiometer with Harness Assembly
1111
8899
1313
10005352
1111
6 RED6 RED
THERMOSTATTHERMOSTAT
Electrical Wiring Diagram without Integral Remote Control
BLACKBLACK
5 BLACK5 BLACK
4 BLACK4 BLACK
BLACKBLACK
10 WHITE10 WHITE
33
FLAME FLAME
MOTORMOTOR
9 WHITE9 WHITE
8 WHITE8 WHITE
3 BLACK3 BLACK
22
11
BLACKBLACK
WHITEWHITE
1010
1010
SWITCH ON/OFFSWITCH ON/OFF
FANFAN
MOTORMOTOR
HEATER ELEMENTHEATER ELEMENT
2 BLACK2 BLACK
44
1010
66
BREAKERBREAKER
CIRCUITCIRCUIT
1 BLACK1 BLACK
7 WHITE7 WHITE
55
1. 120VAC Motor
2. Rocker Switch
3. Thermostat
4. Fan/Heater
5. Light Socket with Wiring
Assembly (2 Lamps)
6. Light Bulb 60 W
7. Breaker Circuit Manual Reset
8. Power Cord
9. Bushing Strain Relief
10. Nylon Cable Tie 61/8 Black
11. Bushing Snap Hole
12. CFM Majestic Factory Wire
77
99
88
10005350
8
10005581
Vermont Castings, Majestic Products DEF/DEFD26
Operating Instructions
NOTE: The control compartment is located behind the upper louvre panel. To access controls, flip the upper
louvre panel down.
3 1245
10005754
Fig. 3 Control locations behind upper louvre panel.
1. Main ON/OFF Switch
The ON/OFF switch supplies power to all functions of
the fireplace. This is an illuminated switch which
normally lights up when in the ON or OFF position.
2. Heater Control
The Heater Control acts to turn the heater ON and
OFF as well as setting the comfort level in the room.
Turning the knob clockwise from the OFF position will
place the heater into operation. The further the knob is
rotated clockwise, the higher the setpoint temperature.
Turning the knob counterclockwise will lower the
setpoint temperature. Turning it all the way
counterclockwise will turn the heater function OFF.
WARNING: During any service of this
appliance, the power to the unit must be
turned
ON/OFF
OFF
. It is not acceptable to use the
switch to meet this requirement.
3. Flame Speed Control
Turn the flame speed control knob to increase or
decrease the flame speed as desired.
4. Re-learn
This model fireplace with integral remote control has a
preprogrammed, matched-pair Receiver/Transmitter
already set with randomly-selected house codes. It is
highly unlikely that the fireplace code will ever need to
be re-learned. If the fireplace needs to re-learn
Receiver/Transmitter house codes, perform the
following steps:
1. Be sure there is power to the fireplace.
2. Be sure there is a good battery in the Transmitter
(hand-held remote).
3. Open the battery compartment of the remote.
4. Press and release the small button located in the
top left corner. This will randomly select a new
house code in the remote Transmitter.
5. Close the remote Transmitter battery
compartment.
6. Press either the ON or OFF button on the remote
Transmitter, and the Learn button on the fireplace
at the same time. The fireplace is now ready to
accept commands from the remote Transmitter.
5. ON/OFF
The ON/OFF button on the fireplace (below the Learn
button) is to turn the fireplace ON and OFF when the
battery in remote Transmitter is weak, or to manually
operate the fireplace without the remote Transmitter.
NOTE: The device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
10005581
9
Vermont Castings, Majestic Products DEF/DEFD26
Replacement Parts List
Item # Part Description
DEF26 DEFD26
1 Log Set Complete 10004588 10004588
2 Fan/Heater 10004198 10004198
3 Flame Generator Motor, 120 Volt AC w/Terminal 10004262 —
4 Cord Power 16/3 HPN w/Terminals 10003095 10003095
5 ON/OFF Switch 10001393 10001393
6 Heater Control (Thermostat) 10004199 10004199
7 Heater Control Knob 10001639 10001639
8 Breaker Circuit Manual Reset 10003093 10003093
9 Flame Generator Assembly 10003350 10003350
10 Screen Light Tinted (not shown) 10005345 10005345
11 Light Bulb Socket w/Wiring Assembly 10003568 10003568
12 Top Louvre Assembly 10005135 10005135
13 Bottom Louvre Assembly 10005153 10005153
14 Frame Door Screen Left Assembly 10005330 10005330
15 Frame Door Screen Right Assembly 10005329 10005329
16 Motor 12 VDC Flame Generator — 10001978
17 Potentiometer w/Harness Assembly — 10001168
18 Circuit Board Flame Speed Control — 10001589
19 Transmitter — 10005140
20 Receiver — 10005141
21 CFM-Majestic Wire (not shown) 10005347 10005758
1
2
11
17
4
20
6
8
16
9
Vermont Castings, Majestic Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and
products at any time, without notice.
19
6
7
12
14
13
3
5
15
5581_DEF26_parts
10
10005581
1 YEAR WARRANTY
For Vermont Castings, Majestic Products Electric Fireplace Models
BASIC WARRANTY:
Vermont Castings, Majestic Products (hereinafter referred to
collectively as the "Company") warrants that your new
Vermont Castings, Majestic Products fireplace is free from
manufacturing and material defects for a period of one (1) year
from date of installation, subject to the following conditions
and limitations:
GARANTIE DE BASE:
Vermont Castings, Majestic Products (aux présentes nommée
la "Société") garantit votre nouveau foyer électrique Vermont
Castings, Majestic Products contre tous défauts de fabrication
et de matières premières pour une période d'un an à compter
de la date d'installation, sujet aux conditions et limitations
suivantes.
1. This electric fireplace must be installed and operated at all
times in accordance with the Installation and Operating
instructions furnished with the product. Any alteration, willful
abuse, accident, or misuse of the product shall nullify this
warranty.
2. This warranty is nontransferable, and is made to the original
owner, provided that the purchase was made through an
authorized supplier of the Company.
3. This warranty is limited to the repair or replacement of part(s)
found to be defective in material or workmanship, provided that
such part(s) have been subjected to normal conditions of use
and service, after said defect is confirmed by the Company's
inspection.
4. This warranty does not cover the lightbulb(s) included with
the Vermont Castings, Majestic Products electric fireplace.
5. The Company may, at its discretion, fully discharge all
obligations with respect to this warranty by refunding the
wholesale price of the defective part(s).
6. Any installation, labour, construction, transportation, or other
related costs/expenses arising from defective part(s), repair,
replacement, or otherwise of same, will not be covered by this
warranty, nor shall the Company assume responsibility for
same. Further, the Company will not be responsible for any
incidental, indirect, or consequential damages, except as
provided by law.
7. All other warranties - expressed or implied - with respect to the
product, its components and accessories, or any obligations/
liabilities on the part of the Company are hereby expressly
excluded.
8. The Company neither assumes, nor authorizes any third party
to assume, on its behalf, any other liabilities with respect to the
sale of this electric fireplace.
9. The warranties as outlined within this document do not apply to
non-Vermont Castings, Majestic Products accessories used in
conjunction with the installation of this product.
This warranty is void if:
a)The fireplace has been operated in atmospheres
contaminated by chlorine, fluorine or other damaging
chemicals.
b)The fireplace is subjected to prolonged periods of
dampness or condensation.
c) Any alteration, willful abuse, accident, or misuse of the
product.
GLASS DOORS & BRASS PLATED PARTS . . .
Glass doors are not warranted for breakage due to misuse or
accident.
Brass parts should be cleaned with lemon oil only. Brass cleaners
cannot be used. Mortar mix and masonry cleaners may corrode
the brass finish. The Company will not be responsible for, nor will it
warrant any brass parts which are damaged by external chemicals.
IF WARRANTY SERVICE IS NEEDED . . .
1) Contact your supplier. Make sure you have your warranty, your
sales receipt, and the model/serial number of your Vermont
Castings, Majestic Products appliance.
DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.
2)
1. Le foyer électrique doit être installé par un entrepreneur de
service autorisé et compétent. Il doit être installé et utilisé en tout
temps selon les instructions d'installation et de fonctionnement
fournies avec le produit. Toute altération, abus volontaire,
accident ou mauvais usage du produit annulera cette
garantie.
2. Cette garantie n'est pas transférable et est offerte à l'acheteur au
détail d'origine, à condition que l'achat soit effectué par l'entremise d'un détaillant autorisé de la Société.
3. Cette garantie est limitée à la réparation ou au remplacement
de(des) pièce(s) trouvée(s) défectueuse(s) en matières premières ou main-d'oeuvre, à condition que lesdites pièces aient été
sujettes aux conditions normales d'usage et de service, après
que ledit défaut a été confirmé par une inspection par la Société.
4. Cette Garantie ne couvre pas les ampoules inclus dans le
foyer électrique Vermont Castings, Majestic Products.
5. La Société peut, à sa discrétion, se décharger entièrement de
toutes obligations se rapportant à cette garantie en remboursant
le prix de gros de la(des) pièce(s) défectueuse(s).
6. Tous les frais/dépenses d'installation, de main-d'oeuvre, de
construction, de transport ou autres causés par une (des)
pièce(s) défectueuse(s), une réparation, un remplacement ou
autre, ne seront pas couverts sous cette garantie, et la Société
n'assume aucune responsabilité pour ceux-ci. De plus, la
Société ne pourra être tenue responsable pour tous dommages
fortuits ou indirects sauf la ou prévu par la loi.
7. Toutes autres garanties, exprimées ou sous-entendues, en ce
qui a trait au produit, ses composants et accessoires, ou toutes
obligations/responsabilités de la part de la Société sont aux
présentes expressément excluses.
8. La Société ni n'assume, ni autorise aucun tiers assumer, en son
nom, des autres dettes en ce qui concerne la vente de cette
cheminée électrique.
9. Les garanties, telles que décrites dans ce document, ne s'appliquent accessoires non Vermont Castings, Majestic Products
utilisés conjointement pour l'installation de ce produit.
10. Cette garantie est nulle si:
a)Le foyer a été utilisé dans une atmosphère contaminée par
du chlore, du fluor ou tous autres produits chimiques.
b)Le foyer est assujetti à de longues périodes d'humidité ou
de condensation.
c) Toute altération, abus volontaire, accident ou mauvais
usage du produit annulera cette garantie.
PORTES EN VERRE & PIÈCES PLAQUÉES LAITON . . .
Les portes en verre ne sont pas garanties contre le bris causé par un
mauvais usage ou un accident.
Les pièces en laiton devraient être nettoyées qu'avec de l'essence
de citron. Les nettoyeurs de laiton ne peuvent pas être utilisés. La
Société ne sera pas responsable pour, et ne garantit pas les pièces
en laiton qui sont endommagées par de refoulement.
SI UN SERVICE SOUS GARANTIE EST REQUIS . . .
1) Communiquez avec votre détaillant. Assurez-vous que vous avez
votre garantie, votre reçu de caisse ainsi que le numéro de modèle/
série de votre produit Vermont Castings, Majestic Products.
NE TENTEZ PAS D'EFFECTUER DES RÉPARATIONS VOUS-MÊME.
2)
Vermont Castings, Majestic Products
410 Admiral Blvd. • Mississauga • Ontario, Canada L5T 2N6 • Ph: 905-670-7777
www.majesticproducts.com • www.vermontcastings.com
Loading...