Vermont Casting 33LDVT User Manual

FIREPLACE & CHIMNEY COMPONENT SPECIFICATIONS

NO

1

”

,

TDVP8

2

6

8

8

564

PERFECTVIEW 33LDVT TOP VENT

578mm

908mm

908mm

806mm

641mm

1283mm

733mm

162mm

368mm

118mm

356mm

753mm

851mm

794mm

838mm

152mm

466mm

51mm

118mm

162mm

225mm

86mm

VENT SECTIONS and OFFSETTING ELBOWS

1219mm

36"

914mm

8"

203mm

7

7"

178mm

24"

610mm

12"

305mm

7TDVP1

7TDVP24 7TDVP3

TE: THE INSTALLED LENGTH OF ANY VENTING SECTION IS

LENGTH

EXCEPT FOR THE LAST SECTION INSTALLED.

48"

7TDVP4

18"

457mm

12"

305mm

7TDVP121

LESS THAN ITS TOTAL

64"

1626mm

889mm

7TDVP3

35"

9

1/4

"

7

1/4

"

9

1/4

"

90°

7

"

13"

9

1/4

"

90

°

13"

7

1/4

"

13"

17

"

OFFSET

235mm

235mm

178mm

184mm

330mm

330mm

335mm

330mm

184mm

OFFSET w/2-90°

Back to Back

CONTEMPORARY TERMINATIONS

7TDV45

7TDVRT90

11"

7

3/8

"

45°

45°

7

3/8

"

OFFSET w/2-45°

Back to Back

45°

7

3/8

"

188mm

188mm

188mm

FP890

FP889

9³⁄₄"

12¹³⁄₁₆"

7"

7TDVSKV

9¹⁄₂"

7"

13³⁄₁₆"

7TDVSKS

32"

6

1/2

"

813mm

127mm

19"

16"

482mm

406mm

165
mm

5

"

ELBOWS

FIREPLACE FACTS

PerfectView 33LDVT

33” PerfectView Direct Vent Gas Appliance

FEATURES:

• 33” PerfectView Direct Vent Gas Appliance

• 11,200 to 16,000 BTU/hr. input

• Patented Insta-Flame TM Ceramic Burner System with 4-piece
Split Oak Ceramic Fiber Log Set

• Tempered Glass Panel Assembly

• Adjustable Flame and Heat Output

• Wall Switch

• 18” Flex Connector with Shutoff and EB1 electrical box installed

• Wall Firestop, Zero Clearance Sleeve (Rear vent models only)

• Rated as Fireplace Heater (AFUE)

• Uses 4”/7” Majestic (Direct Vent) Venting Components.

BURNER SYSTEM:

• Capacity – Natural: 16,000 BTU/HR Max.
11,200 BTU/HR Min.
– Propane: 16,000 BTU/HR Max.
12,000 BTU/HR Min.

• Fuel - Natural or Propane Gas

• Ignition System - Standing Pilot With Piezo Ignitor, A Low Voltage,
Self-Generating Power Pile System (mV)
– No Outside Electrical Power Needed OR
– Electronic ignition that requires 120 VAC Electrical hook up

• Gas Supply Line -

• Gas Inlet and Manifold Pressures

Consult Gas Code Book for Correct Sizing

Natural Propane

Minimum Inlet Pressure 5.5” w.c. 11.0” w.c.
Maximum Inlet Pressure 14” w.c. 14.0” w.c.
Manifold Pressure 3.5” w.c. 10.0” w.c.

MINIMUM FLOOR AREA:

• 33” W X 14” D

HEARTH EXTENSION:

A Hearth Extension Is Recommended But Not Required

ACCESSORIES:

33LDVTCR - 33” LDV Ceramic Refractory - Top
FK12 - Fan and Cord (160cfm) (for RN/RP only)
FK24 - Variable Speed Heat-Activated Fan Kit
IMTFK - IMT Thermostat w/ Face Kit

Minimum Mantel Clearances

Mantel Depth

The Fireplace Facts Information Sheets are for
quick reference only and are subject to change with­out notice. Actual fi replace instructions must abide
by specifi cations provided with each product.

REV. 10/07

2”
4”
6”
8”

10”

Clearance From Top

of Combustion Chamber Opening

To Bottom of Mantel

8

1/2

”

10

1/2

”

12

1/2

”

14

1/2

”

16

1/2

”

m

OPTIONAL ACCESSORIES (Continued):

(Trim Kits continued from second page)

• Louver Kits - Additional Louver Kits ( To replace all louvers in
desired color, 4 sets are required ) See Price List

• Filligree Louver Kits - See Price List

• Perimeter Trim Kits - See Price List

• Face Trim Kits - See Price List

WALL FRAMING DIMENSIONS

Vent Opening for
Combustible Wall

9³⁄₈"

(240 mm)

9³⁄₈"

(240 mm)

FLUE SYSTEM

7” Coaxial Direct Vent Syste

SPECIFICATIONS:

• 7” O.D.

• 4” I.D.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIAL

a) Vertical Side Wall Applications 1” to All Sides
b) Vertical thru the Roof Applications 1” to All Sides

MINIMUM COMBUSTIBLE WALL/FLOOR OPENINGS

a) 9 3/8” W x 9 3/8” H for Vertical Side Wall/Vertical
Applications

AXIMUM INSTALLATION LENGTHS

a) Vertical Side Wall Applications
36” (914 mm) Horizontal Vent Length with 90°
elbow installed directly on top of the unit
20ʼ (6 m) Horizontal Vent Length with

7.5ʼ (2.29 m) vertical rise
*Refer to manual for alternative venting distance

VERTICAL THRU THE ROOF APPLICATIONS

• 8ʼ (2.4 m) Minimum Vertical Rise

• 40ʼ (12 m) Maximum Vertical Rise

• 2 sets of 45° Elbows can be used in Vertical
rise with 8ʼ maximum distance between elbows

• Two 90° elbows maximum for 10ʼ (3 m)

Horizontal can be installed in Vertical Applications

Fireplace Hearth

Framing Detail

Opening for Non-combustible Wall

Rnd.

7¹⁄₂" Dia.

(190 mm)

VO584-100

MINIMUM FRAMING DIMENSIONS

2 x 4's

2 x 4

Header

2 x 4

33-1/2"

(851mm) (851mm)

2 x 4

29-5/8"

(753mm)

14-1/2"

(368mm)

33-1/2"

*Maximum angular variation for Vertical Sidewall/Vertical

Application in system is total of 270°

*Refer to installation manual for all venting restrictions

with elbow use

TERMINATION CLEARANCES MINIMUM

a) Horizontal
12” (305 mm) above Grade Level
18” (458 mm) to Ventilated Soffi t
12” (305 mm) to Unventilated Soffi t
12” (305 mm) under veranda, porch,

deck or balcony

b) Vertical

24” (610 mm) Above a Roof Surface and any other
obstruction within a horizontal distance
of 18” (458 mm)

*Refer to installation manual for more termination
restrictions

PRODUCT LISTING

33LDVT ANSI Z21.88 - 2005/CSA 2.33 2005
Vented Gas Fireplace Heaters

This gas appliance should be installed by qualifi ed installers
in accordance with local building codes and the current
National Fuel Gas code ANSI Z223.1 or CSA B 149.1
Installation code for Gas Burning Appliance and Equipment.