Vermeiren Express V Instruction Manual
VERMEIREN
Express V
I N S T R U C T I O N M A N U A L
M O D E D ’ E M P L O I
G E B R U I K S A A N W I J Z I N G
G E B R A U C H S A N W E I S U N G
I S T R U Z I O N I P E R L ' U S O
MA N U A L D E I N S TR U C C I O N E S
Instructions to the specialist dealer
This instruction manual is part and parcel of the product and must accompany every product sold.
Version: A, 2013-06
All rights reserved, including translation.
No part of this manual may be reproduced in any form what so ever (print, photocopy, microfilm or any other process) without
written permission of the publisher, or processed, duplicated or distributed by using electronic systems.
© N.V. Vermeiren N.V. 2013
Instructions pour les distributeurs
Ce manuel d'instructions fait partie du produit et doit accompagner chaque produit vendu.
Version : A, 2013-06
Tous droits réservés, y compris la traduction.
Aucune partie de ce manuel ne peut être reproduite, sous quelque forme que ce soit (imprimée, photocopie, microfilm ou tout autre
procédé) sans l'autorisation écrite du publicateur, ni traitée, dupliquée ou distribuée à l'aide de systèmes électroniques.
© N.V. Vermeiren N.V. 2013
Instructies voor de vakhandelaar
Deze handleiding is deel van het product en dient bij iedere product te worden geleverd.
Versie: A, 2013-06
Alle rechten, inclusief vertaling, voorbehouden.
Niets uit deze handleiding mag geheel of gedeeltelijk in enige vorm (druk, fotokopie, microfilm of ieder ander procedé) zonder de
schriftelijke toelating van de uitgever worden gereproduceerd of met behulp van elektronische systemen worden verwerkt,
gekopieerd of verspreid.
© N.V. Vermeiren N.V. 2013
Hinweise für den Fachhändler
Diese Gebrauchsanweisung ist Bestandteil des Produkts und ist bei jeder Produkts auszuhändigen.
Version: A, 2013-06
Alle Rechte, auch an der Übersetzung, vorbehalten.
Kein Teil der Gebrauchsanweisung darf in irgendeiner Form (Druck, Fotokopie, Mikrofilm oder einem anderen Verfahren) ohne
schriftliche Genehmigung des Herausgebers reproduziert oder unter Verwendung elektronischer Systeme verarbeitet, vervielfältigt
oder verbreitet werden.
© N.V. Vermeiren N.V. 2013
Istruzioni per il rivenditore
Il presente Manuale di istruzioni è parte integrante del prodotto e deve essere fornito assieme alla prodotto.
Versione: A, 2013-06
Tutti i diritti riservati (anche sulla traduzione).
Il presente manuale non può essere riprodotto, neppure parzialmente, con alcun mezzo (stampa, fotocopia, microfilm o altro
procedimento) senza l’autorizzazione scritta della casa produttrice, né elaborato, duplicato o distribuito con l’ausilio di sistemi
elettronici.
© N.V. Vermeiren N.V. 2013
Instrucciones destinadas a los distribuidores especializados
El presente manual de instrucciones es parte integrante del producto y se debe adjuntar a todas las producto que se vendan.
Versión: A, 2013-06
Todos los derechos reservados, incluidos los de la traducción.
Se prohíbe la reproducción total o parcial del presente manual de cualquier forma (impresión, fotocopia, microfilm o cualquier otro
procedimiento), así como la edición, copia o distribución empleando sistemas electrónicos, sin el permiso escrito del editor.
© N.V. Vermeiren N.V. 2013
Express V
2013-06
Page 1
Contents
1 Productdescription .............................................................................................................. 3
1.1 Intended Use ............................................................................................................... 3
1.2 Technical specifications .............................................................................................. 4
1.3 Components ................................................................................................................ 6
1.4 Accessories ................................................................................................................. 6
1.5 Explanation of symbols .............................................................................................. 6
1.6 Safety instructions ...................................................................................................... 7
2 Use ........................................................................................................................................... 8
2.1 Remarks on electromagnetic compatibility (EMC) .................................................... 8
2.2 Carrying the electric wheelchair ................................................................................. 9
2.3 Assembly and disassembly of the electric wheelchair ............................................... 9
2.4 Fold up or unfolding the wheelchair ......................................................................... 10
2.5 Mounting or removing backrest ................................................................................ 11
2.6 Mounting or removing battery housing ..................................................................... 11
2.7 Mounting or removing armrest ................................................................................. 12
2.8 Mounting or removing of the footrests ..................................................................... 12
2.9 Operating the parking brakes .................................................................................... 13
2.10 Transfer in and out the electric wheelchair ............................................................... 13
2.11 Correct position in the electric wheelchair ............................................................... 14
2.12 Driving the electric wheelchair ................................................................................. 14
2.13 Operating the electromagnetic brakes ...................................................................... 14
2.14 Driving the electric wheelchair on stairs .................................................................. 18
2.15 Driving the electric wheelchair on ramps ................................................................. 18
2.16 Pushing the wheelchair ............................................................................................. 19
2.17 Transport in the car ................................................................................................... 20
2.18 Transport in an airplane ............................................................................................ 20
2.19 Batteries .................................................................................................................... 21
2.20 Battery charger .......................................................................................................... 21
2.21 Charging the batteries ............................................................................................... 21
2.22 Thermal fuse ............................................................................................................. 22
3 Installation and adjustment ............................................................................................. 22
3.1 Tools ......................................................................................................................... 22
3.2 Manner of delivery ................................................................................................... 22
3.3 Possible adjustments ................................................................................................. 23
3.4 Battery connections .................................................................................................. 24
3.5 Changing the batteries .............................................................................................. 25
3.6 Tyre changing ........................................................................................................... 25
4 Maintenance ........................................................................................................................ 26
Express V
2013-06
Page 2
Preface
First of all we want to thank you for putting your trust in us by selecting one of our products.
The expected lifetime of your electric wheelchair is strongly influenced by the care and
maintenance of the wheelchair.
This manual will help you get acquainted with the operation of your electric wheelchair.
Following of the user instructions and the maintenance instructions are an essential part of
the warranty.
This manual reflects the latest product developments. Vermeiren has the right to introduce
changes without the obligation to adapt or replace previously delivered models.
For any further questions, please consult your specialist dealer.
Express V
2013-06
Page 3
1 Productdescription
1.1 Intended Use
The electric wheelchair Express V is equipped with two motors, of 200W.
The electric wheelchair Express V is intended to comfortably transport persons with walking
difficulties or no walking abilities. This electric wheelchair is designed to transport 1 person.
The electric wheelchair is designed to transport persons only, no goods.
Neither should it be used by persons obviously suffering from physical or mental limitations
(e.g. visual impairment, ...) that render them incapable of safely handling the electric
wheelchair.
The different types of fittings and accessories, and the modular construction allow full use by
persons disabled by:
• paralysis
• loss of limbs (leg amputation)
• limb defects or deformations
• stiff or damaged joints
• heart insuffiencies and poor blood circulation
• balance disturbances
• cachexia (decrease in muscle)
The electric wheelchair is classified as class A.
The electric wheelchair is suited for indoor and limited outdoor use by the occupant.
The user can operate the wheelchair by himself or have the wheelchair pushed by an
attendant with the handgrips.
When providing for individual requirements:
• body size and weight (max. 90 kg)
• physical and psychological condition
• residential circumstances
• environment
should be taken into consideration.
Your electric wheelchair should be used on flat surfaces where all four wheels are touching
the ground and where there is sufficient contact to operate the wheelchair safely.
You should practice for use on uneven surfaces (cobblestones, etc.), slopes, curves and to
get past obstacles (curbs, etc.). A particular risk is involved when crossing surfaces such as
ice, grass, rubble, foliage, etc.
The electric wheelchair should not be used as a ladder, nor is it a transport for heavy or hot
objects.
When using your electric wheelchair on streets or footpaths, local laws and regulations apply.
The electric wheelchair can be used on sidewalks, urban road. Under no circumstances the
electric wheelchair may be used for driving on larger roads or expressways.
Use only Vermeiren approved accessories.
The manufacturer is not liable for damage caused by the lack of improper service or as a
result of not following instructions from this manual.
Visually impaired people can contact the dealer for the instructions for use.
Express V
2013-06
Page 4
1.2 Technical specifications
Technical terms below are valid for the electric wheelchair in standard settings and optimum
environmental conditions. If accessories are used, the tabulated values will change. Changes
in outdoor temperatures, humidity, uphill's, downhill's, soils and battery levels can reduce
output.
Brand
Vermeiren
Address
Vermeirenplein 1/15, B
-
2920 Kalmthout
Type Electric wheelchair
, Class
A
Model
Express
V
Maximum occupant mass
90 kg
Des
cription
Dimensions
Effective seat width 390 mm 420 mm 440 mm 460 mm 500 mm
Overall width (depends on the seat
width)
560 mm 580 mm 600 mm 620 mm 640 mm
Description
Dimensions Minimum
Dimensions Maximum
Max. speed 6 km/h
Continuous driving distance range* Approx. 18 km (batteries 38 Ah)
Overall length with footrest 950 mm
Overall height (backrest included) 960 mm
Folded / dismantled length (without
footrests, armrests, battery
housing)
790 mm
Folded / dismantled width
(wheelchair folded)
400 mm
Folded / dismantled height (without
backrest, without armrests)
710 mm (for seat width 460 mm; depends on seat width)
Total mass 71,90 kg (For seat width 460 mm;
depends on seat width and any accessories)
Mass of heaviest part (that can be
dismantled or removed)
Frame
,
armrest
+ joystick
:
29,15 kg
(for seat width 460 mm, depends on seat width)
Masses of parts that can be
dismantled or removed.
Arm
rest without joystick
:
1,60 kg;
Footrests:
1,80 kg;
Battery housing: 33,25 kg (Batteries: 27,15 kg);
Seat cushion: 3,30 kg ; Backrest: 2,40 kg ; Pushbar: 0,5 kg
Static stability downhill 7,5°
Static stability uphill 12°
Static stability sideways 10°
Obstacle climbing 15 mm
Ground clearance 30 mm
Seat plane angle 5°
Effective seat depth 430 mm
Thickness seat cushion 40 mm
Seat surface height at front edge
(with seat cushion)
540 mm
Backrest angle 5°
Backrest height 430 mm
Distance between footrest and seat
400 mm 520 mm
Angle between footrest and
footplate
80 ° 100 °
Angle between seat and footrest 105°
Express V
2013-06
Page 5
Brand
Vermeiren
Address
Vermeirenplein 1/15, B
-
2920 Kalmthout
Type Electric wheelchair
, Class
A
Model
Express
V
Maximum occupant mass
90 kg
Description
Dimensions Minimum
Dimensions Maximum
Angle between seat and footplate 5° 25°
Distance between armrest and seat
(with seat cushion)
225 mm 315 mm
Front location of armrest structure 400 mm
Driving motors 2 x 200W
Batteries 2 x 12V
/ 38 Ah / 20 hr
Battery charger
See separate manual battery charger
(Use ONLY the battery charger
that is delivered with your electric wheelchair)
Thermal fuse 30 AMP
Control unit See separate manual control unit / Electromagnetic braking system
Minimum turning diameter Approx. 1400 mm
Reversing width Not applicable
Diameter Rear wheels (number) 12 1/2 x 2 1/4" air (2)
Tyre pressure, rear wheels ** Max. 2,5 bar
Diameter front wheels (number) 200 x 50 mm air (2)
Tyre pressure, front wheels ** Max. 3 bar
Noise level < 65 dB (A)
Storage and use temperature -20 °C to +40 °C
Operating temperature of the
electronics
-10 °C to +40°C
Storage and use humidity 30% 70%
We reserve the right to introduce technical changes. Measurement tolerance
± 15 mm / 1,5 kg / ° .
* The theoretical driving distance will be reduced if the wheelchair is used frequently on slopes, rough
ground or to climb curbs.
**Since different tyres may be used, please note the correct operating pressure of the tyres you use.
For other tyre diameters refer to your specialist dealer.
Table 1: Technical specifications
The wheelchair complies to the requirements set up in:
ISO 7176-8: Requirements and test methods for static, impact and fatigue strengths.
ISO 7176-14: Wheelchairs - Part 14: Power and control systems for electrically powered
wheelchairs and scooters -- Requirements and test methods
EN 1021-1: Furniture - Assessment of the ignitability of upholstered furniture - Part 1 :
Ignition source smouldering cigarette
EN 1021-2: Furniture - Assessment of the ignitability of upholstered furniture - Part 2 :
Ignition source match flame equivalent
Express V
2013-06
Page 6
1.3 Components
1.4 Accessories
The following accessories are available for the electric wheelchair Express V:
• Back inclination (SE52)
1.5 Explanation of symbols
Maximum mass
Indoor and limited outdoor use
Indoor use (Only for battery charger)
Separate recovery and recycling of electric and electronic devices (Only for Battery charger)
Protection class II
Minimum slope
CE conformity
Maximum speed
Position: Parking brakes activated (electric driving possible)
Position: Parking brakes deactivated (free running and pushing possible, no electric driving)
During free running, be careful with slopes and inclinations
Not crash-tested
1 = Handgrips
2 = Backrest
3 = Adjustable armpads
4 = Armrests
5 = Battery housing
6 = Parking brakes
7 = Driving wheels (rear wheels)
8 = Driving Motors
9 = Basic frame
10 = Front forks
11 = Steering wheels (Front wheels)
12 = Footplate
13 = Footrests
14 = Identification plate
15 = Seat cushion
16 = Operator unit
Express V
2013-06
Page 7
1.6 Safety instructions
L
To prevent injury and/or damage to your wheelchair, make sure that no objects and/or
body parts are caught in the rims of the driving wheels.
L
Follow the instructions for using your wheelchair. For example, avoid driving without
brakes against an obstacle (step, edge of the curb) or dropping down from steps.
L
When getting into and out of the wheelchair, do not stand on the footplates. The
footplate should be folded up beforehand.
L
Investigate the effects of shifting the centre of gravity on the behavior of the wheelchair,
for example on up or down gradients, on laterally sloping ground, or when overcoming
obstacles. Obtain support from an attendant.
L
If you want to pick up something (lying in front of, on the side, or to the rear of the
wheelchair), you should not lean too far out to avoid tipping over.
L
When moving through doors, arches, etc. ensure that there is enough room at the sides
so that you do not get your hands or arms caught or crushed and that there is no
damage to the wheelchair.
L
Avoid uncontrolled rolling against obstacles (steps, curbs, doorframes, etc) or dropping
down from ledges. The manufacturer cannot assume liability for damage caused by
overloading, collision or other improper use.
L
When moving in public places, you are subject to local regulations.
L
Influence of medicine or alcohol reduces your driving capabilities.
L
When travelling outdoors, adapt your driving to weather and traffic conditions.
L
Do not use your electric wheelchair in rainy conditions.
L
Do not put your electric wheelchair into the free-wheeling position on slopes.
L
Never reverse uphill.
L
Reduce speed when you go round corners.
L
To be better visible when driving in the dark, wear the brightest possible clothing or
clothes with reflectors and make sure that the reflectors of the wheelchair are clearly
visible and drive with lightning on.
L
Make sure that the lights and reflectors of your electric wheelchair are free from dirt
and/or other objects that could hide them.
L
When transporting the wheelchair, never pick it up by grasping movable parts (wheels,
armrests, footrests, etc.)
L
When transporting the electric wheelchair, no persons may be transferred along with it.
L
No additional passengers may be taken.
L
When storing or parking your electric wheelchair outside, protect it with a shrouding
cover against humidity.
L
High levels of humidity or very cold conditions can reduce the performance of your
electric wheelchair.
L
Never use your electric wheelchair as a seat in an automobile or other vehicle
.
L
Never exceed the maximum load of 90 kg.
L
Use only Vermeiren approved accessories.
L
Before getting on or off, taking apart or transporting your electric wheelchair, put your
wheelchair off with the "ON/OFF" button.
L
Check that the profile depth of the tyres is adequate.
L
If your electric wheelchair has pneumatic tyres, be careful to inflate them to the correct
pressure (see pressure indication on the tyres).
L
Stairs may only be negotiated by an attendant. If devices and furnishings like ramps or
lifts are available, use them.
L
Risk of injury in case of a sudden stop - Always use the safety belt.
Express V
2013-06
Page 8
2 Use
This chapter describes the everyday use. These instructions are for the user and the
specialist dealer.
To find a service facility or specialist dealer near you, contact the nearest Vermeiren facility. A
list of Vermeiren facilities can be found on the last page.
The electric wheelchair is delivered fully assembled by your specialist dealer. The
instructions intended for the specialist dealer for adjusting the electric wheelchair are given in
§ 3.
2.1 Remarks on electromagnetic compatibility (EMC)
Your electric wheelchair has been tested according EN 61000-4-3 and EN 61000-4-2 for
EMC-compliance.
We wish to point out that sources of electromagnetic waves are liable to create interferences.
The electronics of the wheelchair itself could affect other electric appliances too.
To reduce the effect of electromagnetic sources of interference, please read the following
warnings:
L
WARNING:
The wheelchair might disturb the operation of devices in its
environment that emit electromagnetic field.
L
WARNING:
The driving performance of the wheelchair can be influenced by
electromagnetic fields (e.g. electricity generators or high power sources).
L
WARNING:
Avoid using any portable TV or radio in the immediate environment of
your wheelchair for as long as it is turned on.
L
WARNING:
Avoid using any transmitter-receiver in the immediate environment of
your wheelchair for as long as it is turned on.
L
WARNING:
Check the area for transmitter masts and avoid using the wheelchair
close to them.
L
WARNING:
If involuntary movements or braking occur, turn off the wheelchair as
soon as it is safe to do so.
Interfering electromagnetic fields may have a negative effect on the wheelchair’s electronic
systems. These can include:
• Disengagement of the engine brake
• Uncontrollable behavior by the wheelchair
• Unintentional steering movements
In the presence of very strong or enduring interfering fields, the electronic systems could
even break down entirely or suffer permanent damage.
Possible sources of radiation include:
• Portable receiver and transmitter installations (receiver and transmitter with fixed
antenna)
- Transmitting and receiving sets
- Portable TV, radio and navigation devices
- Other personal transmitting devices
• Mobile medium-range transmitting and receiving devices (e.g. car antennas)
- Fixed transmitting and receiving sets
- Fixed mobile transmitting and receiving devices
- Fixed radio, TV and navigation systems
Express V
2013-06
Page 9
• Long-range transmitting and receiving devices
- Radio and television towers
- Amateur radio sets
• Other home devices
- CD player
- Notebook
- Microwave oven
- Cassette recorder
- etc.
Devices like electric shavers and hair dryers will have no influence provided that they
function perfectly and their cabling be in an excellent condition. Please conform to the
operating instructions accompanying such electric instruments to ensure trouble free
operating of your wheelchair.
2.2 Carrying the electric wheelchair
The best way to carry the electric wheelchair is to make use of free-wheel mode of the
electric wheelchair. Place the wheelchair in free-wheel mode and roll the wheelchair with the
handgrips to the desired place.
When the wheelchair must be taken up or down stairs, do this with the wheelchair ramps or
lift systems. At least two persons are required to move the wheelchair up or down stairs or
over single steps.
Another way to carry the electric wheelchair is to dismantle the electric wheelchair. Carry the
separate parts (frame, armrests, footrests, battery housing, seat, backrest) to the desired
place. Grasp the wheelchair only on fixed frame parts (never by the footrests, armrests and
wheels).
2.3 Assembly and disassembly of the electric wheelchair
The electric wheelchair is delivered fully assembled. Your dealer delivers the wheelchair fully
assembled and explains the various operating elements and their use. However, for your
own safety we provide a further, detailed explanation of the different parts.
Express V
2013-06
Page 10
2.3.1 Assembly of the electric wheelchair
To assembly the electric wheelchair:
1. Unfold the wheelchair (paragraph 2.4).
2. Mount the backrest (paragraph 2.5), seat.
3. Place the battery housing on the guide rails next to the motors (paragraph 2.6).
4. Mount the armrests (paragraph 2.7).
5. Mount the footrests (paragraph 2.8).
6. Fold the footplates of the footrests down.
To disassembly the electric wheelchair do the reverse of the above instructions.
2.4 Fold up or unfolding the wheelchair
LLLL
CAUTION:
Risk of clamping – Keep fingers, buckles, clothes away from moving
parts of the wheelchair (eg. cross, ...).
To unfolding the wheelchair:
1. Position yourself behind the wheelchair.
2. Use the hand-grips to open the wheelchair as much as possible.
3. Position yourself at the front of the wheelchair.
4. Push both seating tubes down till they are fixed in their position.
5. Place the battery housing on the guide rails.
To fold up the wheelchair:
1. Remove the battery housing.
2.
Fold the footplates or remove the footrests (see § 2.8).
3. Remove the preshaped seat.
4. Lift the cross tubes upwards out the seat frame. Be careful for pinching your fingers.
Express V
2013-06
Page 11
2.5 Mounting or removing backrest
LLLL
WARNING:
Risk of injury – Make sure that both securing levers are engaged.
LLLL
CAUTION:
Chance of pinching – Do not place fingers between the backrest tubes
of the wheelchair.
For transport the backrest of the wheelchair can be completely removed.
To mount the backrest on the electric wheelchair:
1. Check that the levers are not fixated otherwise
loosen the levers .
2. Mount the backrest tubes Ⓐ in the hexagonal
tubes of the frame Ⓑ.
3. Retighten the levers properly.
To remove the backrest from the electric
wheelchair:
1. Turn on the levers until they come loose.
2. Remove the backrest tubes Ⓐ out the hexagonal
tubes of the frame Ⓑ.
2.6 Mounting or removing battery housing
LLLL
CAUTION:
Chance of pinching – Do not place fingers between the battery
housing and guide rails of the wheelchair.
To mount the battery housing on the electric wheelchair:
1. Grasp the handles to lift the battery housing.
2. Lift the battery housing with the plastic bushings on the rails .
3. Slide the battery housing backwards in the correct position.
4. Turn the locking hook clockwise to secure the battery housing.
5. Check that the battery housing is firmly fixated to avoid damage to the battery housing.
6. Connect the cables from the electronic.
To remove the battery housing of the electric wheelchair:
1. Disconnect the cables from the electronic.
2. Turn the locking hook anti-clockwise to loosen the battery housing.
3. Slide the battery housing to the front.
4. Grasp the handles to lift the battery housing.
5. Lift the battery housing out the rails .
Express V
2013-06
Page 12
2.7 Mounting or removing armrest
LLLL
WARNING:
Risk of injury and/or damage - Make sure that the levers are
properly tightened before using the wheelchair.
LLLL
WARNING:
Risk of tipping over - Check that the armrests are at the same height
on each side.
LLLL
CAUTION:
Risk of clamping – Keep fingers, buckles and clothes away from the
attachment points of the armrests.
The armrests can be removed so the patient can be moved sideways. The armrests
can also be removed for therapeutic purposes and to move the patient from the wheelchair.
To mount the armrests on the electric wheelchair:
1. Mount the armrest in the rectangular tube .
2. Retighten the handle properly. (If the lever of handle
is not in a good position, press on button on the
handle and place the lever in a good position that no
risk of injury to the hands can appear).
To remove the armrests from the electric wheelchair:
1. Turn on the handle until it come loose. (If the lever
of handle is not in a good position, press on button
on the handle and place the lever in a good
position that no risk of injury to the hands can appear).
2. Remove the armrest out the rectangular tube .
The armpads are adjustable in different heights over a range of 90 mm (stepless) Keep a
safe distance from 10 mm on the bottom of the armrest.
1. Loosen the lever a little.
2. Move the rectangular tubes and over each other until the desired armpad height.
3. Retighten the lever hand-tightened.
4. Check that the lever is securely fixed.
5. Adjust the other armpad with the same instructions.
2.8 Mounting or removing of the footrests
LLLL
CAUTION:
Risk of injury – Make sure that the footrests are firmly fixated.
The mounting of the footrests is done as follows:
1. Hold the footrest sideways at the outside of the
wheelchair frame and mount the tube hood into the
frame.
2. Swing the footrest inwards till it clicks in position.
3. Swing the foot plate downwards.
4. Check that the footrest is well fixated.
To take off the footrests:
1. Pull handle .
2. Swing the footrest to the outside of the wheelchair till it
comes loose from the guidance.
3. Pull the footrest from tube hood .
Express V
2013-06
Page 13
2.9 Operating the parking brakes
For each drive wheel your electric wheelchair has standard parking brakes.
LLLL
WARNING:
The brakes are not used to slow down the wheelchair during
movements – Use the brake only to prevent the wheelchair from unintended
movements.
LLLL
WARNING:
Good operation of the brakes is influenced by wear and
contamination of the tires (water, oil, mud, …) – Check the condition of the tires
before each use.
LLLL
WARNING:
The brakes are adjustable and can wear – Check the operation of the
brakes before each use.
To apply the brakes:
1. Push the brake levers forward till you feel a
distinctive click.
LLLL
CAUTION:
Risk of unintended movement –
Make sure the wheelchair is on a flat
horizontal surface before releasing the
brakes. Never release both brakes
simultaneously.
To release the brakes:
1. Release one brake by pulling the lever
backwards.
2. Release the second brake by pulling the lever
backwards.
2.10 Transfer in and out the electric wheelchair
LLLL
WARNING:
Power down the wheelchair before getting in or out the wheelchair.
LLLL
CAUTION:
In case you cannot perform the transfer in a safe manner, ask
someone to assist you.
LLLL
CAUTION:
Risk of injury – Do not use the joystick, footplates, armrests as
support.
LLLL
CAUTION:
Risk of tipping over of the wheelchair – Do not stand on the footplates.
1. Park the electric wheelchair as close as possible to
the place where you want to transfer.
2. Check that the operator unit is switched off. Make
sure that the wheelchair is NOT in freewheel
mode.
3. Fold the footplates upwards to prevent standing on
them.
4. If the transfer is on the side of the wheelchair,
remove the armrest on that side.
5. Transfer to / from the electric wheelchair.
Express V
2013-06
Page 14
2.11 Correct position in the electric wheelchair
Some recommendations for a comfortable use of the electric wheelchair:
1. Position your backside as close as possible to the backrest.
2. Make sure your upper legs are horizontal – If needed adjust the length of the footrests.
2.12 Driving the electric wheelchair
LLLL
WARNING:
Risk of burns – Be careful when driving in hot or cold environments
(sunshine, extreme cold, etc.) for a sufficient amount of time and when
touching - Surfaces can assume the environment temperatures.
LLLL
WARNING:
Risk of unsafe settings - Use only the driving characteristics
described in this manual.
2.12.1 Preparing the electric wheelchair for use
When you start using your electric wheelchair, make sure that it is standing on level ground.
All wheels must be in contact with the ground.
1. Make sure that the freewheel mode is OFF and the operator unit is switched off.
2. Adjust the wheelchair best suited for yourself.
3. Set the operator unit in the most comfortable position.
4. Sit down on the seat and verify that both armrests have been adjusted so your
forearms are folded down.
5. Put your wheelchair on with the "ON/OFF" button from the operator unit.
Now put the speed control on the operator unit to the minimum position. Your electric
wheelchair is now ready for use.
2.12.2 Handling after usage
Before getting off from your electric wheelchair, make sure that all four wheels touch the
ground simultaneously.
Push on the "ON/OFF" button from the operator unit, the display of the operator unit goes
out.
2.13 Operating the electromagnetic brakes
Let go of the joystick to stop the electric wheelchair.
2.13.1 Parking the electric wheelchair
Once your electric wheelchair has been turned off, no command can be sent to the driving
system. Always park your electric wheelchair on sites that are easy accessible and on
horizontal surfaces that the four wheels are touching the ground.
2.13.2 Operator units
* Controller
The instructions for use from the operator units you can find in the seperate user manals of
the operator units that is included with your wheelchair.
Changing the software is only allowed by Vermeiren. For changes in the software
contact Vermeiren.
Express V
2013-06
Page 15
2.13.3 Adjusting operator unit
LLLL
CAUTION:
Risk of pinching - Do not put your fingers between the operator
control and the other parts when positioning the operator unit.
The operator unit's horizontal position can be changed:
1. Loosen screw just under the armpad a little bit.
2. Move the operator unit to the desired position or remove the operator unit.
3. Retighten screw properly.
If you pull screw to the side, the operator unit can be turned to the side.
NOTE: Depending on the features of your wheelchair, screw could also be located
beneath the guide tube ➁ .
2.13.4 Connections for charger / program unit
LLLL
WARNING:
Risk of injury - Check that all plugs (battery charger and
programming unit) are removed before setting the wheelchair in motion.
The socket for connecting the charger supplied is
located on the front of the operator unit. Here, too, is
the connnection for the programming unit, which
should only be connected and used by authorised
persons who have been trained to program it
(Vermeiren personnel).
Make sure that the joystick is in the neutral
(central) position when pressing the on/off
button, otherwise the electronics will be blocked.
This block can be lifted by switching the control
unit off and then on again.
1
2
Express V
2013-06
Page 16
2.13.5 Your first trip
LLLL
WARNING:
Control your electric wheelchair - Accustom yourself with the driving
behavior of your electric wheelchair.
• Driving
Once you are seated on your electric wheelchair and have started it as described above,
take the joystick with your hand and push this in the required direction i.e.:
PUSH ACTION FORWARD = FORWARD MOVEMENT
PUSH ACTION BACKWARD = BACKWARD MOVEMENT
• Braking
To brake, let go of the joystick, which will let it return to the zero position and slow down your
electric wheelchair to a gentle stop. Practice pulling away and braking to get accustomed to
the electric wheelchair. You need to be able to estimate how your electric wheelchair will
react when you drive or brake.
• Driving in corners and bends
LLLL
WARNING:
Risk of tipping over - Reduce your speed before you enter a curve or
corner.
LLLL
WARNING:
Risk of clamping - Always maintain an adequate distance from
corners and obstacles.
Move the joystick into the position you wish to turn. The front wheels will turn accordingly and
steer the electric wheelchair into a new direction. It is very important that you ensure that
there is enough space allowing you to go around bends and corners. Narrow passages must
preferably be approached in a large curve so as to allow you to enter the narrowest part as
straight from the front as possible.
Take care not to enter curves and corners diagonally. By ‘cutting the corner’, chances are
that your rear wheels, back of wheelchair will run into obstacles and destabilize your electric
wheelchair.
2.13.6 Backward movement
LLLL
WARNING:
Control your electric wheelchair - Accustom yourself with the driving
behavior of your electric wheelchair.
LLLL
WARNING:
Control your speed - Always go backward in the lowest speed
possible.
LLLL
WARNING:
Risk of collision - Always look to the back when you go backward.
Backward driving requires increased concentration and care. This explains why we have
greatly reduced the speed of backward movement in comparison with forward driving. But we
still recommend that you put the speed on minimum when you drive backward.
Left and right controls act inverse when driving backwards.
Express V
2013-06
Page 17
2.13.7 Going uphill
LLLL
WARNING:
Control your electric wheelchair - Accustom yourself with the driving
behavior of your electric wheelchair.
LLLL
WARNING:
Control your electric wheelchair - Never put your electric wheelchair
in freewheel on slopes.
LLLL
WARNING:
Control your speed - Move on slopes as slow as possible.
LLLL
WARNING:
Risk of tipping over - Do not exceed the maximum gradient of static
and dynamic stability uphill (see paragraph "Technical specifications").
LLLL
WARNING:
Never reverse going uphill.
Always approach slopes directly from the front and, to avoid tipping over, see that all four
wheels stay in contact with the ground at all times (ramps, driveways, etc.).
If you come to a stop on a slope by letting go of the joystick, the engine break will prevent
your electric wheelchair from rolling backward. As soon as the joystick returns to zero
position, the engine break is activated.
To resume your uphill drive, push the joystick as much as possible to the front to ensure the
release of a sufficient amount of power. This will allow your electric wheelchair to slowly
ascend the slope.
If your wheelchair is unable to drive up, turn the speed control up and try again.
2.13.8 Going downhill
LLLL
WARNING:
Control your electric wheelchair - Accustom yourself with the driving
behavior of your wheelchair.
LLLL
WARNING:
Control your wheelchair - Never put your electric wheelchair in
neutral on slopes.
LLLL
WARNING:
Control your speed - Move on slopes as slow as possible.
LLLL
WARNING:
Risk of tipping over - Avoid sharp bends.
LLLL
WARNING:
Risk of tipping over - Do not exceed the maximum gradient of static
and dynamic stability downhill (see paragraph "Technical specifications").
Always approach downhill slopes directly from the front. Slantwise approaches can lead to
some of the wheels no longer staying in contact with the ground (danger of tipping over).
The weight of the electric wheelchair will increase your downhill speed. Lower the speed on
the operator unit.
Avoid sharp bends on downhill slopes. The weight of your electric wheelchair could cause
your electric wheelchair to lift up on one side or even fall over around bends.
Express V
2013-06
Page 18
2.14 Driving the electric wheelchair on stairs
LLLL
WARNING:
Risk of injury - Sit quietly in your wheelchair and avoid jerky
movements. If you cannot sit quietly when being transported because of illness
or disability (e.g. slightly spastic, etc.), then at least two persons are required to
secure the wheelchair on both sides by taking hold of fixed parts of the frame.
LLLL
WARNING:
Risk of injury – Wear suitable safety belt systems while being
transported (information obtainable from your specialist dealer).
LLLL
WARNING:
Risk of injury – Make sure that your arms and legs do not protrude
outside the wheelchair while being driving on stairs.
If you want to be taken up or down stairs with the wheelchair, you will need wheelchair ramps
or wheelchair liftsystems.
2.15 Driving the electric wheelchair on ramps
LLLL
WARNING:
Risk of injury - Do not exceed the maximum load of the ramps.
LLLL
WARNING:
Risk of injury - Choose the correct ramps to prevent injury or
damage.
LLLL
WARNING:
Risk of injury - Be sure that the wheel height is high enough to get
over the free height of the ramps. The electric wheelchair frame may not touch the
ramps.
LLLL
WARNING:
Risk of injury - Use a restraining safety belt to secure yourself in your
wheelchair.
LLLL
WARNING:
Risk of tipping over - Put the adjustment functions (seat, back,
footrests, ...) so that the wheelchair has the best stability.
Should you wish to use ramps to drive over an obstacle, please note the following:
1. Find out from the manufacturer what the maximum load is for the ramps.
2. Drive on the ramps at the lowest speed possible.
3. See the instructions in the chapter "your first trip".
If the wheelchair has adjustment functions, ensure that (because these has influence on the
stability of the electric wheelchair):
1. The seat is in the lowest position as possible and in the horizontal position.
2. The back is in the upright position.
3. The footrests have been set so that no collision can occur while passing the obstacle.
If another person is pushing you, note that the large weight of the electric wheelchair exerts
appreciable reverse forces.
Express V
2013-06
Page 19
2.16 Pushing the wheelchair
LLLL
WARNING:
Control your electric wheelchair - Never put your electric wheelchair
in neutral while you are driving.
LLLL
WARNING:
Control your electric wheelchair - Never put your electric wheelchair
in neutral on slopes. It may accidentally roll away.
The wheelchair is fitted with a freewheel device that is accessible and operable only by the
attendant.
2.16.1 200W motors - 6km/h
Put the chair in neutral with the adjusting levers on both motors. These levers are located
on the back of the electric wheelchair.
Clutch or declutch the motor by following the instructions below:
DRIVING
Pull the adjusting levers of both motors in the driving position. Loosen the parking
brakes. Switch the operator unit out and in. Electronically controlled driving is now
possible.
NEUTRAL
Push the adjusting levers of both motors in the neutral position and you will
activate the wheelchair's free-running mode. The wheelchair can now be pushed
without electronic drive.
In free wheel mode, the electronic brake is deactivated and the wheelchair will no
longer be held back. Do not activate free wheel mode on slopes.
L
When free-running is activated, the
electromagnetic braking system is
deactivated, so the wheelchair is no
longer secured against rolling away.
Take care not to set the wheelchair
down on slopes or uneven terrain,
or it may accidentally roll away.
L
The electronic system will indicate,
through the lock symbol flashing,
that electronic driving is not
possible.
Neutral
Driving
Express V
2013-06
Page 20
2.17 Transport in the car
L
DANGER:
Risk of injury – The wheelchair is not suited for use as a seat in a
motor vehicle.
L
WARNING:
Risk of injury - No people or objects should be under the electric
wheelchair, during transportation.
L
WARNING:
Risk of injury - See that the wheelchair is attached properly. So you
can avoid injury from the passengers during collision or sudden braking. Make
sure that they are only attached to solid parts of the frame.
L
WARNING:
Risk of injury- Use for attaching the wheelchair and passenger
NEVER the same seatbelt.
Never use your wheelchair as a seat in an automobile or other vehicle. The wheelchair shall
be marked with following symbol.
To transport the wheelchair in the car use following steps:
The best way to transport your electric wheelchair in the car is to drive the electric wheelchair
in the car by using ramps.
When you are not experienced to drive the electric wheelchair by using of ramps you can
also put the wheelchair in neutral mode and push the wheelchair in the car by using ramps.
When the wheelchair does not fit in the car it is also possible to transport the wheelchair by
the following steps:
1. Remove all moveable parts prior to transporting (footrests, armrests, etc.).
2. Store moveable parts safely.
3. Place the electric wheelchair in the car with 2 persons by grasping to the fixed parts of
the frames.
4. Attach the solid parts of the frame securely to the vehicle.
5. Place the wheelchair in drive mode (engage the parking brakes) and check that the
operator unit is switched off.
2.18 Transport in an airplane
The electric wheelchair can be transported in an airplane. Electric wheelchairs shall be
checked at the desk. Announce the wheelchair on time by the concern airline before
departure. Do not use the electric wheelchair as a seat in an airplane, the wheelchair must
be stored in the cargo room.
To transport the wheelchair in an airplane note the following requirements:
1. Type and properties of wheelchair (joystick, batteries)
The wheelchairs shall be foreseen of dry or gel batteries. Mostly these batteries must not
be removed out the wheelchair. Only disconnect and insulate the electrical connections
on the battery.
2. Dimensions and weight of the wheelchair
The allowable weight and dimensions of the wheelchair depends on the type of the
airplane.
Express V
2013-06
Page 21
3. Damage on the wheelchair
It is possible that the wheelchair could be damaged because the wheelchair will be
stored in a narrow area with the suitcases and other goods.
To prevent damage on the wheelchair:
• Put the electrical adjustments in standard position (lift column as low as possible,
seat inclination horizontal, back inclination the most foreward).
• Fold the footplates upwards, place the armrests in the most inward position.
• Check that the adjustment levers shall positioned inwards.
• Cover the operator unit with a soft material that can withstand shocks.
Before travelling contact the concerned airline about the requirements for
transporting the wheelchair in an airplane.
2.19 Batteries
The standard for your electric wheelchair are two closed batteries, 12 V/38 Ah. The batteries
used with your electric wheelchair are drive batteries which only attain full capacity after a
few charging and use cycles.
If the batteries loose their power after long usage, or if they are damaged, get them both
replaced by a specialist dealer only.
We accept no liability for damage caused through using other types of batteries.
If the batteries are opened, all manufacturer liability and all claims will become void.
Do not use the batteries at temperatures below -5°C or above +50°C (the ideal is: +20°C).
Use only the original batteries. We do not accept any liability for damages resulting
from use of other batteries.
2.20 Battery charger
To charge the batteries, only use the battery charger supplied.
For the user instructions of the battery charger you can refer to the manual that is delivered
with your battery charger.
2.21 Charging the batteries
LLLL
CAUTION:
Risk of injury - Only use the battery charger supplied to charge
batteries.
As the charger aligns the charge curve with the batteries charge level, you can recharge your
wheelchair after each use. This avoids any aggressive battery charging and the "memory
effect".
Recharge the wheelchair, at the latest, when the charge indicator on the operator unit goes
into the red zone. If, despite this, you continue driving, eventually only the last red diode
lights up and flashes continually, indicating that the batteries are nearly flat. If you disregard
this warning signal, too, an error message will shortly appear indicating that the batteries can
no longer provide power for driving. The batteries should therefore be charged before these
error messages appear, using the supplied battery charger. Avoid the batteries becoming
drained, in any case.
For the use of the battery charger refer to the separate manual of the battery charger.
If you decide not to use your electric wheelchair for an appreciable period, you must
nevertheless recharge it regularly to keep it in a running condition ready for immediate use.
Express V
2013-06
Page 22
The manufacturer accepts no liability for damage caused by improper charging.
For further information, please refer to the user instructions provided with the charger.
2.22 Thermal fuse
To protect the motor against overload, on the
back of the wheelchair topside of the battery
housing, there is a thermal safety mechanism
that will automatically cut off the motor to prevent
overheating and thus rapid wear and tear or
breakdowns. This can occur if you go up or down
slopes that exceed the maximum gradient
indicated. Nominal loads exceeding the
maximum could also trigger the safety
mechanism.
To be able to use the electric wheelchair again, remove the overload and wait till the motor
has cooled down. Then gently press the thermal safety mechanism back in. Your wheelchair
is now ready for use again.
3 Installation and adjustment
The instructions in this chapter are for the specialist dealer only.
The Express V has been designed as a rear wheel drive electric wheelchair.
LLLL
WARNING:
Risk of unsafe settings - Use only the settings described in this
manual.
LLLL
WARNING:
Risk of tipping over - Variation allowed adjustments can still change
the stability of your wheelchair (tilt back or sideways).
3.1 Tools
To set up the wheelchair the following tools are needed.
• Wrench set n° 8 to n° 19
• Allen keyset n° 3 to n° 6
• Screwdriver Phillips head
3.2 Manner of delivery
The electric wheelchair shall be delivered with:
• Framework with armrests, operator unit, rear and front wheels, seat and backrest
• 1 pair of footrests
• 2 x drive batteries + battery housing, 2 x drive motors
• Battery charger + manual of battery charger
• Electronics
• Tools
• Operator unit + manual operator unit
• Accessories
Before use, check that everything is included and that no products are damaged (example
by transport, ...). Please note that the basic configuration may differ in different European
countries. Contact your specialist dealer.
Express V
2013-06
Page 23
3.3 Possible adjustments
LLLL
WARNING:
Risk of injury - Turn the electric wheelchair off before you perform any
adjustments.
LLLL
WARNING:
Risk of injury - Never perform any adjustments while you are driving.
LLLL
WARNING:
Risk of injury - Adjustments may only performed by your specialist
dealer.
LLLL
WARNING:
Risk of injury - Make sure all screws, levers are firmly secured
before driving with your electric wheelchair.
L
L L
L
CAUTION:
Risk of clamping – Keep fingers, buckles and clothes away from the
attachment points or any moving parts.
3.3.1 Adjusting the armrests
The width of the armrests can be adjusted in horizontal direction.
1. Loosen the hexagon socket set screws
just under the seat frame.
2. Move the armrest in an horizontal direction
until the correct position, by moving the
rectangular tubes and over each
other. (Range 60 mm: step less)
3. Retighten the screws properly.
4. Repeat instructions above for the other
armrest.
Check that the armrests are positioned
identically on both sides.
3.3.2 Adjusting of the footrests
* Adjusting length:
LLLL
CAUTION:
Risk of damage – Avoid that the footrests make any contact with the
ground. Keep a minimum distance from 30 mm above the ground.
Adjust the length of the footrests as follow:
1. Remove the screw (on the back of the
footrests).
2. Adjust the length of the footrest to a comfortable
length (range: 120 mm, stepless).
3. Tighten the screw
properly.
Express V
2013-06
Page 24
* Adjusting the footplates:
The footplates can be used in 2 positions. Standard they are adjusted with the base plate in
the back position.
The footplates can be adjusted to the front by switching the left and right footplate.
* Adjusting the footplates:
Adjust the angle of the footplates as follow:
1. Loosen bolt .
2. Adjust tube in the desired angle. The angle indication (80°-85°-90°-95°-100°) is
according the dashes .
3. Retighten the bolt .
3.4 Battery connections
LLLL
CAUTION:
Risk of injury - Check that no tools or other conductive objects come
between the batteries poles, to avoid unintentionally current flows.
LLLL
CAUTION:
Risk of injury, damages - Do not work in a humid environment with
batteries and electronics.
The best way to disconnect the batteries:
1. Disconnect the main negative pole (-).
2. Disconnect the positive pole (+).
3. Disconnect the bridge.
To connect the batteries use the reverse order.
-
Battery
+
+
Battery
-
24
30
A
Red
Red
Black
Bridge
2
1
3
1
2
100°
80°
3
Express V
2013-06
Page 25
3.5 Changing the batteries
LLLL
CAUTION:
Risk of burns – Do not come in contact with the acid from the
batteries. See for a good ventilation of the battery compartment.
The battery shall be changed by trained personnel.
The battery can be changed according following
steps:
1. Remove the battery housing from the wheelchair.
2. Remove the battery cover by loosen the belt
.
3. Disconnect all the wires on the batteries, power
module.
4. Lift the batteries out the battery housing.
5. Place the new batteries in the battery housing.
6. Connect all the wires to the batteries.
7. Replace the battery cover with the belt .
3.6 Tyre changing
LLLL
CAUTION:
There must be no air in the tube before the tyre can be removed.
LLLL
CAUTION:
Risk of damage - If handled improperly, the rim might become
damaged.
Only an expert can guarantee correct assembly. Work not done by your specialist
dealer, would void any warranty claims.
Use only inflating equipment which complies to regulations and indicates the pressure in bar.
We do not accept any liability for damage caused by using inflation equipment or wheels not
supplied by the manufacturer.
LLLL
WARNING:
Risk of injury - Check that the pressure is correct.
LLLL
CAUTION:
Risk of injury - Make sure that no objects, body parts or inner tubes
are pinched between the tyre and the rim when mounting a tyre.
• Steering wheels (front wheels)
Removing tyre from rim:
1. Let all the air out of the tube.
2. Insert a tyre lever between the tyre and the rim.
3. Slowly and carefully push the lever downwards. This will pull the tyre over the edge of the
rim.
4. Move the lever along the rim, the tyre will jump out.
5. Now carefully remove the tyre from the rim and then remove the tube.
Note the following before inserting the new tube:
Check the rim bed and the inside wall of the tyre for foreign matter and clean these properly
if necessary. Check the condition of the rim bed, especially around the position of the air
valve. Please use only genuine original replacement parts. No liability is accepted for
damage caused by non-genuine replacement parts. Kindly contact your specialist dealer.
Express V
2013-06
Page 26
Assembly tyre from rim:
Put the deflated tube around the center of the rim. Make sure that the
valve juts out the valve opening in the rim.
Push the tyre over the edge of the rim, starting behind the air valve. Inflate
the tube slightly until it is round, and place it inside the tyre.
If the tube fits snugly inside the tyre without any folds (in the case of folds:
let out some air), then the upper side of the tyre can be pressed lightly
onto the rim with both hands, starting at the air valve.
Check all around on both sides that the tube is not pinched between the rim and the edge of
the tyre. Lightly push the air valve inwards and pull it out again to make sure that the tyre is
positioned properly in the region of the air valve.
To ensure that the wheel is inflated correctly, admit only so much air initially that the tyre can
still be easily pushed inwards by using your thumbs. If the check-lines are equidistant from
the edge of the rim on both sides of the tyre, then the tyre is centered properly. If not - let out
the air and position the tyre afresh. Now the tyre can be inflated to its full operating pressure
(note the maximum) and the valve cap should be replaced.
When inflating the tyres, always check that the pressure is correct. The correct pressure is
given on the tyre sides.
• Driving wheels (rear wheels)
LLLL
WARNING:
Risk of injury - Make sure all screws are firmly secured by hand
before driving with your electric wheelchair.
DISMANTLING
1. Loosen and remove the wheel fastenings .
2. Take the complete rear wheel from the motor axle .
ASSEMBLY
1. Make the threads and Motor axle free from dirt and grease the threads.
2. Mount the rear wheel on the motor axle so that the wheel hub fits on the motor axle
groove.
3. Secure the wheels firmly with the nut (wheel fastenings ).
4 Maintenance
For the maintenance manual of the electric wheelchairs refer to the Vermeiren website:
www.vermeiren.be.
1 = Motor axle
2 = Rear wheel
3 = Wheel fastening
Express V
2013-06
Page 1
Table des matières
1 Description du produit ........................................................................................................ 3
1.1 Utilisation prévue ....................................................................................................... 3
1.2 Spécifications techniques ........................................................................................... 4
1.3 Composants ................................................................................................................ 6
1.4 Accessoires ................................................................................................................. 6
1.5 Explication des symboles ........................................................................................... 6
1.6 Consignes de sécurité ................................................................................................. 7
2 Utilisation ............................................................................................................................... 8
2.1 Explication de la compatibilité électromagnétique (EMC) ........................................ 8
2.2 Transport du fauteuil électrique .................................................................................. 9
2.3 Montage et démontage du fauteuil électrique ........................................................... 10
2.4 Plier et déplier le fauteuil roulant ............................................................................. 10
2.5 Montage ou retrait du dossier .................................................................................... 11
2.6 Monter ou enlever le boîtier de la batterie ................................................................. 11
2.7 Placer ou enlever l'accoudoir .................................................................................... 12
2.8 Placer ou enlever les repose-pieds ............................................................................ 13
2.9 Utilisation des freins de stationnement ..................................................................... 13
2.10 Transfert dans et hors du fauteuil électrique ............................................................. 14
2.11 Position correcte dans le fauteuil électrique ............................................................. 14
2.12 Rouler avec le fauteuil électrique ............................................................................. 14
2.13 Utilisation des freins électromagnétiques ................................................................. 15
2.14 Rouler avec le fauteuil électrique sur des escaliers .................................................. 18
2.15 Conduire le fauteuil électrique sur des rampes ......................................................... 18
2.16 Pousser le fauteuil roulant ........................................................................................ 19
2.17 Transport en voiture .................................................................................................. 20
2.18 Transport dans un avion ............................................................................................ 20
2.19 Batteries .................................................................................................................... 21
2.20 Chargeur de la batterie .............................................................................................. 21
2.21 Chargement des batteries .......................................................................................... 21
2.22 Fusibles thermique .................................................................................................... 22
3 Installation et réglage ........................................................................................................ 22
3.1 Outils ........................................................................................................................ 22
3.2 Mode de livraison ..................................................................................................... 23
3.3 Réglages possibles .................................................................................................... 23
3.4 Raccordement des batteries ...................................................................................... 25
3.5 Remplacement des batteries ..................................................................................... 25
3.6 Changer les pneus ..................................................................................................... 26
4 Maintenance ........................................................................................................................ 27
Express V
2013-06
Page 2
Préface
Nous tenons tout d'abord à vous remercier de nous avoir fait confiance en choisissant l'un de
nos produits.
La durée de vie attendue de votre fauteuil roulant électrique est fortement influencée par
l'entretien et la maintenance dont il bénéficie.
Ce manuel vous familiarise avec la commande de votre fauteuil roulant électrique.
Le respect des instructions d'utilisation et des instructions de maintenance est une condition
essentielle de la garantie.
Ce manuel reflète les derniers développements du produit. Vermeiren est autorisé à apporter
des modifications sans devoir pour autant adapter ou remplacer les modèles fournis
précédemment.
Pour toute question, consultez votre distributeur.
Loading...